Documentos de Académico
Documentos de Profesional
Documentos de Cultura
TRANSFERENCIA DE CALOR
INTEGRANTES:
JUAN ESTEBAN GÓMEZ ROJAS - 5211107
HECTOR ALEJANDRO VELASQUEZ PINEDA- 5211130
JAIRO AREVALO CARDENAS - 6201130
RESUMEN ABSTRACT
En esta práctica se emplearán los conceptos de la In this practice the concepts of one-dimensional
conducción estacionaria unidimensional; calor, stationary conduction will be used; heat,
temperatura, pared multicapa, aislantes, temperature, multilayer wall, usable, conductivity
conductividad y resistencia térmica. and thermal resistance. By means of different
Por medio de diferentes materiales ( cartón, materials (cardboard, acetate, ethyl-vinyl acetate,
acetato, Etil-vinil acetato, MDF, cartulina y papel MDF, cardboard and iris paper) cut in a circular
iris) recortados de forma circular se planea way, it is planned to present how they act in an
presentar como estos actúan de manera aislante, occupational way, in order to determine the linear
para así, determinar la conductividad lineal y por conductivity and therefore the variation in terms of
consiguiente la variación en cuanto a la transmisión to the transmission of generated heat or also known
de calor generada o también conocida como as temperature variation. These materials have a
variación de temperatura. certain degree of thickness that will be taken into
Dichos materiales presentan cierto grado de espesor account for data collection and solution of
que se tendrá en cuenta para la toma de datos y unknowns or variables that arise. On the meter is a
solución de incógnitas o variables que se presentan. cooling water flow that is estimated to reach
En el medidor se encuentra un flujo del agua de approximately 1.5 l/min. For this practice, the
enfriamiento que se estima para llegar a tener water flow remains constant for the two data
aproximadamente 1,5 l/min. Para esta práctica, el collections that will be carried out, the variables
flujo del agua permanece constante para las dos will be voltage and current. In this case, and as
tomas de datos que se llevarán a cabo, las variables mentioned above, two sensors will be carried out,
serán el voltaje y la corriente. En este caso, y como in the first, there will be a voltage of 1.5 V and a
se mencionó anteriormente, se llevarán a cabo dos current of: 0.15 A, for the second data collection, 2
mediciones, en la primera, se tendrá un voltaje de V and 0.20 A, respectively .For each measurement
1.5 V y una corriente de: 0.15 A, para la segunda for each material, a total of 8 temperatures will be
toma de datos, 2 V y 0.20 A, respectivamente. taken, in the first four the record of the higher
Por cada medición para cada material, se tomará un temperatures will be kept and in the following 4 the
total de 8 temperaturas, en las cuatro primeras se decrease of these due to the flow of water and the
llevará el registro de las temperaturas superiores y impermeable material will be shown. Once the data
en las 4 siguientes se muestra la disminución de is taken, calculations are proposed to give
estas por el flujo del agua y el material aislante. necessary results to be measured, such as: the
Una vez tomados los datos, se plantean cálculos average conductivity of the brass bar, the heat flow,
para dar resultados a mediciones necesarias como the temperature changes and the temperature
lo son: la conductividad media de la barra de latón, gradient.
el flujo de calor, los cambios de temperatura y el
gradiente de temperatura.
PALABRAS CLAVE:
Propiedades termicas, Adiabatico, Temperatura, Aislante, Conductividad
DIAGRAMA DE FLUJO
MATERIALES Y MÉTODOS
TOMA N °1
Tabla N°1. Variación de temperatura respecto al material aislante, voltaje y corriente iniciales.
Tabla N°2. Variación de temperatura respecto al material aislante, voltaje y corriente secundarias..