Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Pantalla anterior
Bienvenido: pvaldez
Producto: TALADR O S R O TATIVO S / SO BR E O R UGA
Mode lo: MD6420C TALADR O S R O TATIVO S / SO BR E C ADENAS DW 9
C onfiguración: UTILIZAR IDENTIFIC AC IÓ N DE PIEZAS EXPANDIDAS
MINER ÍA DW 900001-UP (MÁQ UINA)
i06891560
Especificación
tabla 1
Válvula de control LS - Prueba y ajuste
Herramientas necesarias
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 1/7
21/2/2021 USE PARTS IDENTIFICATION EXPANDED MINING DW900001-UP (MACHINE)(SEBP6510 - 00) - Documentación
Ilustración 1 g01623868
Tooling group "B"
198-4240 Digital Pressure Indicator Gp
Table 2
Tool Item Part Number Description Qty
B1 198-4234 Indicator 1
E Fitting assembly 2
E1 6S-5693 Adapter-Tee 2
E2 6V-8925 Adapter 2
E4 3J-1907 Seal-O-Ring 2
Introduction
The Mast, jacks, winch, and water valve, is a proportional, pressure compensated, load-sensing (LS), directional control
valve, with LS pressure reliefs in winch section.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 2/7
21/2/2021 USE PARTS IDENTIFICATION EXPANDED MINING DW900001-UP (MACHINE)(SEBP6510 - 00) - Documentación
Illustration 2 g06003372
(1) Directional Control Valve
(2) Adjustment Screw
(3) Locknut
(4) Adjustment screw
(5) Locknut
Machine Preparation
1. Position the machine on level ground and stop the engine.
Illustration 3 g06006578
(6) Hose
(7) Hose
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 3/7
21/2/2021 USE PARTS IDENTIFICATION EXPANDED MINING DW900001-UP (MACHINE)(SEBP6510 - 00) - Documentación
Test Procedure
1. Start the engine.
3. Increase the hydraulic oil temperature to a minimum of 40°C (104°F). Refer to Testing and Adjusting, "Hydraulic
System Warm-up" for any additional information.
Illustration 4 g06006672
(8) Winch control lever
5. While lowering the winch, monitor the pressure. If pressure is within specification, no adjustment is needed. Refer
to Table1 for specification.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 4/7
21/2/2021 USE PARTS IDENTIFICATION EXPANDED MINING DW900001-UP (MACHINE)(SEBP6510 - 00) - Documentación
Illustration 5 g06006680
(8) Winch control lever
7. While raising the winch, monitor the pressure. If pressure is within specification, no adjustment is needed. Refer to
Table 1 for specification.
Adjustment Procedure
Winch Raise
Illustration 6 g06003372
(1) Directional Control Valve
(2) Adjustment Screw
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 5/7
21/2/2021 USE PARTS IDENTIFICATION EXPANDED MINING DW900001-UP (MACHINE)(SEBP6510 - 00) - Documentación
(3) Locknut
(4) Adjustment screw
(5) Locknut
2. Simultaneously move the control lever (8) and monitor the pressure.
Note: Turn adjustment screw (2) CLOCKWISE to increase pressure or COUNTERCLOCKWISE to decrease
pressure.
3. Adjust the adjustment screw (2) until pressure is within specification. Refer to Table 1 for specification.
Winch Lower
Illustration 7 g06003372
(1) Directional Control Valve
(2) Adjustment Screw
(3) Locknut
(4) Adjustment screw
(5) Locknut
2. Simultaneously move the control lever (8) and monitor the pressure.
Note: Turn adjustment screw (4) CLOCKWISE to increase pressure or COUNTERCLOCKWISE to decrease
pressure.
3. Adjust the adjustment screw (4) until pressure is within specification. Refer to Table 1 for specification.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 6/7
21/2/2021 USE PARTS IDENTIFICATION EXPANDED MINING DW900001-UP (MACHINE)(SEBP6510 - 00) - Documentación
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/sis… 7/7