Documentos de Académico
Documentos de Profesional
Documentos de Cultura
MAQUINA:
TRACTOR ORUGA
NOMBRE:SAMUEL QUISPE TICONA
PROFESOR:JESÚS VILLALOBOS PEÑA
AULA:A
AÑO:2014
MAJES-PEDREGAL
INTRODUCCION
En el presente trabajo nos dispondremos a analizar las funcionalidades del buldócer o tractor
sobre orugas el cual es un pilar fundamental dentro de la construcción, en lo que es
movimiento de tierras para urbanizaciones en general como para labores forestales de
construcción de caminos y otros.
MANTENIMIENTO Y REPARASION DEL TRACTOR
ORUGA
De oruga
Enllantados.
Al seleccionarse un tractor debe considerarse distintos factores que determinaran el tamaño,
potencia, tipo de hoja a utilizar, entre otros. Algunos de estos factores son:
El tamaño que se requiere para determinada obra.
La clase de obra en la que se empleara, conformación, jalando una es crepa, jalando un vagón, arando,
etc.
Especificaciones
Motor
Sistema de carburante con inyección directa. Gobernador mecánico a toda velocidad. Lubricación
forzada conducida por la bomba de engranaje. A todo régimen para la purificación del lubricante. Filtro
de aire dry-type con el evacuador del polvo y el indicador automático de polvo. Motor de arranque
eléctrico de 24V/11 kW. Alternadores 24V/35. 2 baterías de 12V/140 Ah (amperio hora).
Número de cilindros 6
Manejo
Controles single-rever para todos los movimientos direccionales. Incline simplemente la palanca a la
izquierda para hacer una curva a la izquierda. Inclínela a la derecha para hacer una vuelta a la derecha.
Empujar la palanca adelante da lugar al movimiento delantero; el tirar hacia el operador retrocede la
máquina. Sistema de manejo hidrostático (HSS) del tipo planetario diferenciado del engranaje.
Accionado por el motor hidráulico, actuando hidráulicamente, y la funcionalidad manual.
Tren de aterrizaje
Funcionamiento de la presión
sobre la tierra 8,20 PSI 0,57 kg/cm?
Capacidad del líquido refrigerador y del lubricante (al rellenar)
Peso del tractor: Incluyendo la capacidad clasificada del lubricante, del líquido refrigerador, de
DISPOSITIVOS DE PROTECCIÓN EN CASO DE VOLCAMIENTO, del depósito de gasolina lleno,
del operador, y del equipo estándar. 34.240 libras 15530 kilogramos
Sistema Hidráulico
la carga de Cerrado-centro que detectaba el sistema (CLSS) se diseñó para el control exacto y reposición
y para la operación simultánea eficiente.
En la Unidad de control hidráulica - todas las válvulas de control del carrete externamente montaron al
lado del tanque hidráulico. Bomba hidráulica volumétrica con la capacidad (flujo de la descarga) de 55,5
U.S gal/min 210 ltr/min en el motor clasificado RPM.
Configuración de la válvula de
descarga 2.990 PSI 210 kg/cm?
Válvulas de control
Posiciones:
Posición - elevación de la
lámina Aumento, asimiento, más bajo, y flotador
Cilindros hidráulicos/Numero
de cilindros Alesaje Alesaje
Dozer de la
inclinación de 17'8 ' ' 7,34 yd? 11'4 ' ' x 4'8 ' ' 3'7 ' '
Semi-U 5390 mm 5,61 m? 3460 mm x1425 mm 1095 mm
Peso adicional -
Gota máxima bajo Ajuste máximo Peso adicional - unidad de control
tierra de la inclinación equipo de Dozer hidráulica Peso adicional
1'6 ' ' 2'11 ' ' 5.090 lb 1.590 lb 1,56 PSI
450 mm 880 mm 2310 kgs 720 kgs 0,11 kg/cm?
Equipo Estándar
Alternador, 35 amperios
Alarmar de reserva
Desacelerador
Defensas
Sistema De Manejo Hidrostático (Hss)
El escarificador montado parece a primera vista más eficaz que el de tracción, pero presenta
el inconveniente de exigir mayor tiempo de montaje. Son muchos los constructores de
escarificadores montados o de tracción, pero los modelos varían poco.
Los dientes escarificadores que se montan sobre la cuchilla de empuje tienen idéntica misión
que el escarificador, pero son de construcción mucho más simple, puesto que la cuchilla y su
bastidor le sirven de asiento. El modo de actuación es diferente: en el escarificador de tracción
la barra de unión al tractor ejerce un esfuerzo dirigido ligeramente hacia arriba, con tendencia
de los dientes a salir del suelo cuando la resistencia es excesiva; se mantienen clavados
gracias a su perfil y al peso del escarificador. El tractor es libre de saltar o patinar cuando el
esfuerzo es excesivo.
Por el contrario, el esfuerzo de presión ejercido por el tractor sobre los dientes fijos montados
en el bulldozer se dirige hacia abajo y tiende a mantener los dientes clavados, sea cualquiera
la resistencia del suelo, retenidos por el cable o los husillos. El tractor no puede así saltar, su
adherencia es mayor y su potencia se utiliza al máximo
Escarificador desraizador Esco
Dientes escarificadores situados delante de la cuchilla del bulldozer. Los dientes
escarificadores están formados por un gancho robusto, regulable en profundidad y con punta
de ataque intercambiable. El diente va sujeto en un alojamiento, fijo a su vez sobre la hoja
mediante dos mordazas que lo afianzan a la parte superior e inferior de la misma, sin
necesidad de abrir orificios. El montaje es fácil y rápido. Estos dientes actúan a la vez que la
cuchilla del bulldozer. El suelo queda con ello mullido a medida que se avanza.
Pueden instalarse, según convenga, uno o dos dientes en la cuchilla. Para desmontarlos se
recomienda clavarlos primero en el suelo, pues así quedan en posición de trabajo y listos para
ser montados de nuevo sin ninguna otra operación
A la izquierda: cuchilla con inclinación vertical; centro: cuchilla recta; derecha: cuchilla
con inclinación horizontal.
OPERACIONES REALIZADAS POR BULLDOZER
EMPUJE
Una operación de empuje se realizara con una hoja frontal de empuje montada en el extremo
frontal del tractor. Las condiciones de carga para el bulldozer, variaran desde las relativamente
ligeras y uniformes, hasta las aplicaciones de fuerza de impacto necesaria, a través de la hoja,
para mover una piedra muy grande, como arrancar una raíz o derribar un árbol. Para llenar los
requisitos de fuerza de impacto, se prefiere la transmisión directa. De lo contrario, para las
variaciones más ligeras y graduales de carga de un bulldozer, es mejor que posea convertidor
de par de torsión. Para todos los usos es mejor tener transmisión de cambios de potencia.
DESMONTE O DESPEJE:
Esta función requiere en la mayoría de los casos de un angledozer que posee una hoja
angular especial de empuje y accesorios de desgarramiento.
DESGARRAMIENTO
Los materiales sólidos o fuertemente consolidados pueden tener que aflojarse sea por una
maniobra de rasgamiento o desgarramiento, o por una perforación o voladura. Cuando las
condiciones del trabajo indiquen operación de desgarramiento, debe hacerse otras
determinaciones preliminares. El uso final del material es importante, si va a ser utilizado como
material de relleno, de nivelado o se va a desechar. Controlando la distancia entre las pasadas
o los accesorios, puede regularse perfectamente bien el tamaño del material arrancado.
DESCRIPCION DE TRABAJO EN OBRAS.
690.028 D33
Métodos, planeamiento y equipos de construcción (David A. Day). 690.028 P462
Pagina internet komatsuamerica.com.
suplementos de revistas de internet.
INGLES
INTRODUCTION
• From caterpillar
• Enllantados.
• The kind of work which was employed, forming, pulling one is crepe,
pulling a wagon, plowing, etc..
• The type of work that has to be done after the work is finished.
FEATURES AND MACHINERY FUNCUIONAMIENTO
YEAR: 1996.
FUEL: oil.
Model HP Kw M lb Sheet
specs
engine
Number of cylinders 6
* Horses with thick hard: hard thick horses appeared for the standard
engine as SAE J1995 conditions.
TRANSMISSION TORQFLOW
0-3.9 MPH 1st Gear 0-2,4 mph 0-5.0 MPH 0 to 3.1 mph
0-4.2 MPH 2nd gear 0 to 6.8 0 to 5.3 mph 0-8.6 MPH MPH
0 to 6.6 0 to 10.6 MPH the 3rd gear mph from 0 to 8.3 0 to 13.4 miles per
hour MPH
Management
Pedal Brakes wet multiple disc, spring-applied, hydraulically on, foot pedal
operated safety lever
Final Drive
Undercarriage
Rollers and Idlers carriel / lubricated track rollers and idlers are sealed with
floating seals
Hydraulics
In the hydraulic control unit - all control valves externally mounted beside
spool hydraulic tank. Hydraulic pump with volumetric capacity (discharge
flow) of 55.5 U.S. gal / min 210 ltr / min at rated engine RPM.
Control Valves
Spool control valve for dozer tilt Semi-U and straight tilt dozer.
positions:
dimensions
N 2.6 '' 65 mm
Sheet
Overall length with blade * Ability dozer blade length blade x Maximum lift
height on earth
7.34 mm d 5390?
1095 mm
1'6 ''
2310 kg 1,590 lb
0.11 kg / cm?
Standard Equipment
Alternator, 35 amp
Alarm booking
Batteries, 2 x 12 V/140 Ah
Fan Blower
decelerator
defenses
It has been seen that the tractor with dozer blade and winch is a machine
that can perform all the work of uprooting. However, it will get better
performance if the tractor is fitted with special accessories.
scarifying machines
Harrow or mounted drive. These machines are used to prepare the work of
the bulldozer. Mullen overly compacted soils, destroy crusts or hard surface
layers, cut and dig up the roots, etc.. Subsequent work of bulldozers, power
shovels or other machines is thus facilitated. There towed or mounted
scarifier, scarifier teeth located in front of the blade and scarifier teeth
located behind the blade.
The scarifier uprooted type (rotate) is the typical machine of this category.
It may be pulling or towing. In the first case, it is equipped with wheels that
support a tool rack height adjustable through a system of cables. If
mounted on the tractor, working bodies adapt to a fixed frame of the
tractor capable of ascent and descent.
The scarifier mounted seems at first more effective than pulling eye, but
has the disadvantage of requiring more assembly time. Many builders
mounted rippers or traction, but the models vary little.
The scarifier teeth that are mounted on the dozer are the ripper same
mission, but are much simpler construction, since the cutter and serve him
seat frame. The mode of action is different: the scarifier bar pull tractor
binding exerts a force directed slightly upward, with teeth tendency to
leave the ground when the resistance is excessive; remain fixed through
your profile and weight of the scaler. The tractor is free to jump or skate
when effort is excessive.
Scarifier teeth located in front of the bulldozer blade. The scarifier teeth are
formed by an adjustable ball and tipped interchangeable sturdy hook
attack. The tooth is clamped in a housing, fixed in turn to the sheet by two
clamps that secure it to the top and bottom thereof, without having to
open holes. Installation is quick and easy. These teeth act while the blade
of the bulldozer. The soil is thereby fluffy as it progresses.
Performance-leveling tractors
Transport of materials
This is the simplest operation, which ultimately may refer other particular
cases. The bulldozers are constructed primarily to transport quickly large
amounts of materials over short distances (50 to 80 m.).
Left: vertical tilt blade; center: straight blade; Right: horizontal tilt blade.
TRANSACTIONS BY BULLDOZER
PUSH
REMOVE OR CLEARANCE:
This function requires in most cases having a particular angledozer angle
dozer attachments and tear.
tear
The crawler is perhaps the most basic and versatile machine in the
construction industry. Serves many purposes, such as pushing or pulling
them move loads such as winches and drive unit for smaller lifters, and as
bulldozer blades, side feathers and front loading bucket.
Mainly used in the early work to fill the swampy area where they currently
work. Thanks to its tracks, this machine can be used in all types of soil
except boggy, so it only moves the filler material to this place to achieve
firmness of the ground where he later worked the rest of the machines.
The material was moved into the marsh. The filling consisted of gravel, sand
and other materials to ensure compaction.
It is also used in the construction of the roads that will be used later for
current traffic of vehicles and machinery, as the drag of vehicles or
machines that get stuck in the sector.
PERFORMANCE FEATURES
The blade of a bulldozer, has a theoretical capacity varies with land classes
and the size of the blade. If the capacity of the blade is known, you can
have. the approximate performance of a machine by estimating the
number of passes that you can make in an hour.
MAINTENANCE
In extreme cases we noted that the limited resources of the machine owner
makes changes, with used parts, which anyway is harmful because life is
much less than a new one.
CONCLUSION
One can conclude from this work that the machine under study, a
bulldozer, gives us great power working in any state of the land except
swamp as I was mentioned but not away from work on steeper slopes of
usually other machines where wheel work since it provides greater stability
for the improved dispersion of the load on the ground itself. Also note the
large power developed even used breaking rocks noting that the lower
ends of the blade has the butt end that are species Rams to a driven best
blade on the ground which was clearly indicated by the operator this
machine.
This work is an opening for the next job on a front loader or a bulldozer
being used in earthworks, which interested me very much for the great
power capabilities of these machines that represent great help in rubra
construction.
REFERENCES