Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Instalacion de Arbol de Leva c2.2
Instalacion de Arbol de Leva c2.2
Procedimiento de instalacion
PPI
-
202 0006
AVISO
13: 3 / 0 0 C8C
6
Mantenga todas las piezas limpias de contaminantes.
0 / 1
KE :52- 0
9
Los contaminantes pueden provocar un desgaste rápido y
reducir la vida útil de los componentes.
N 0
©2 R 694 3:00
023 8
1. Asegúrese de que el conjunto del árbol de levas esté limpio y sin daños.
Cat
2. Lubrique los cojinetes del árbol de levas con aceite de motor limpio.
erp
illa
r In
c.
Ilustración 1 g01311416
ejemplo tipico
https://sis2.cat.com/#/print-preview/service/%257B%2522title%2522%253A%2522Camshaft%2520-%2520Install%2520(KENR6948-11)%2522%… 1/4
10/6/23, 10:09 SIS 2.0
Ilustración 2 g01311407
ejemplo tipico
3. Instale con cuidado el conjunto del árbol de levas (8) en el bloque de cilindros. Asegúrese de
que las marcas de superhéroe (X) estén alineadas en los siguientes engranajes:
https://sis2.cat.com/#/print-preview/service/%257B%2522title%2522%253A%2522Camshaft%2520-%2520Install%2520(KENR6948-11)%2522%… 2/4
10/6/23, 10:09 SIS 2.0
Ilustración 3 g01311411
Ejemplo típico
Nota: El motor C2.2 tiene un retenedor de árbol de levas diferente al de los motores C1.1, C1.5
y C1.7. El procedimiento de extracción es similar para todos los modelos. El C1.1 tiene
sujetadores diferentes a los de C1.5, C1.7 y C2.2. El procedimiento de extracción es similar
para todos los modelos.
4. Place camshaft retainer (5) in position. Align the holes in the retainer with the holes in the
cylinder block.
5. Rotate camshaft gear (4) to align the access hole in the camshaft gear with the hole for fastener
(2).
For the C1.1, C1.5, and C1.7 engines, install allen head screw or bolt (2) and bolt (1). Tighten
fasteners (1) and (2) to a torque of 10 N·m (89 lb in).
For C2.2 engines, install bolt (2) and tighten the bolt to a torque of 10 N·m (89 lb in). Rotate
camshaft gear (4) to align the access hole in the camshaft gear with the hole for bolt (1). Install
bolt (1) and tighten the bolt to a torque of 10 N·m (89 lb in).
7. If the engine is equipped with a mechanical fuel transfer pump, install the fuel transfer pump.
Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove and Install".
End By:
https://sis2.cat.com/#/print-preview/service/%257B%2522title%2522%253A%2522Camshaft%2520-%2520Install%2520(KENR6948-11)%2522%… 3/4
10/6/23, 10:09 SIS 2.0
a. Instale los elevadores. Consulte Desarmado y Armado, "Grupo elevador - Quitar e instalar".
PPI-00060C8C
2023/06/10
13:09:42-03:00
i02873594
© 2023 Caterpillar Inc.
https://sis2.cat.com/#/print-preview/service/%257B%2522title%2522%253A%2522Camshaft%2520-%2520Install%2520(KENR6948-11)%2522%… 4/4