Documentos de Académico
Documentos de Profesional
Documentos de Cultura
FACULTAD DE INGENIERÍA
PROGRAMA CURRICULAR DE INGENIERÍA CIVIL
UNIDAD ACADÉMICA DE GEOTECNIA
TALLER 1
2. Sobre muestras de limos arcillosos (MH) se realizan dos ensayos triaxiales tipo
(CU). En el primero, la presión de cámara total es de 2Kg/cm2 y la falla ocurre a un
esfuerzo axial adicional de 6 Kg/cm2. En el segundo el esfuerzo total de
confinamiento es de 3.5 Kg/cm2 y la falla ocurre a un esfuerzo vertical adicional de
10.5 Kg/cm2.
a) ¿Qué valores de la cohesión (c) y del angulo de fricción (φ) corresponden los
resultados?
b) Graficar la trayectoria de esfuerzos en los planos (s vs t) y (q vs p) para los
especímenes ensayados.
c) Si en este material el parámetro Af representativo es de 0.65, ¿cuál es el
incremento no drenado de la presión de poros en la falla?
4. Dadas las mismas condiciones iniciales del problema anterior dibuje las trayectorias
de esfuerzos para carga, cuando:
∆𝜎𝑣
a) = ∆𝜎ℎ
3
∆𝜎𝑣
b) = ∆𝜎ℎ
4
1 100 238 36
tf = s`(sen`) + c`(cos`)
(a) Create a graph with the x-axis as p, p` and the y-axis as q. Calculate and plot
the initial mean effective stress and deviatoric stress.
(b) Calculate the increase in mean total stress and deviatoric stress.
(c) Plot the current total and effective stress paths (assume the soil is a linear,
isotropic, elastic material, A=0.33).
(d) Determine the slopes of the total and effective stress paths and the maximum
excess porewater pressure.
(a) Plot the initial stress state and the total stress path in (p, q) space.
(b) Plot the effective stress path assuming that the soil is a linearly elastic material.
(c) Determine the maximum excess porewater pressure.
10. An oil tank (10 m in diameter) is to be constructed on a 10m thick layer of soft,
normally consolidated clay classified as CH. Its saturated unit weight is 18.8
kN/m3 and the lateral earth pressure coefficient at rest is Ko=0.5. Groundwater
is at the surface. The clay is underlain by a sand classified as SP. The estimated
settlement of the tank is intolerable. The geotechnical engineer proposes to
preload the soft clay by constructing the tank and then filling it with water in
stages. The dead load of the tank and its foundation will impose a uniform vertical
stress of 25 kPa at the ground surface. The water level in the tank for the first
stage of loading is 2 m. For a soil element at a depth of 5 m under the center of
the tank:
(a) Calculate the initial mean total and effective stresses and the initial deviatoric
stresses. Create a graph with the x-axis as p, p` and the y-axis as q. Plot the initial stress
state.
(b) Calculate the total vertical stress applied at the ground surface when the tank is filled
with 2 m of water.
(c) Calculate the increase in vertical and lateral stresses on the soil element due to the
total applied surface stress when the tank is filled with 2 m of water.
(d) Calculate the increase in mean total stress and deviatoric stress due to the total
applied surface stress
when the tank is filled with 2 m of water.
(e) Plot the total stress path when the tank is filled with 2 m of water. Clearly label this
stress path.
(f) If the soft clay were to behave as an isotropic, elastic material, plot the effective stress
path and calculate the increase in pore water pressure.
11. For figure 11, calculate the normal stress and the shear stress for the inclined
plane and the magnitude and direction of the principal stresses. Show the
graphical (Möhr Circle) and the analytical solution.
Figure 11.
12. In figure 12, for the inclined plane (), determine the normal and shear
stresses. Show the graphical (möhr circle) and the analytical solution.
Figure 12
14. Assume that a soil’s specific gravity Gs is 2.65, the void ratio is 0.91, and the effective
stress parameter (c) varies linearly with saturation from c= 0 at S= 0 to c=1.0 at S=100%.
What is the relationship between c and gravimetric water content w? What is the
relationship between c and volumetric water content Ѳw? Hint: Se=Gsw, and Ѳw = Se/(1+e).
15. What are the major mechanisms to explain soil-water hysteresis? Given these
mechanisms, explain why the same soil has higher soil suction when drying than
when wetting? Will suction stress be higher during a drying process or a wetting
process?
16. The following stress components are measured at a point in an unsaturated where
x and y are the horizontal directions, z is the vertical direction, positive stress or
pressure is compressive, and negative stress or pressure is tensile.
17. If the stress components at the same point as Problem 16 change to the following
values:
b. Las dimensiones del cimiento para el mismo factor de seguridad indirecto del
punto (a), considerando la excentricidad causada por el momento.
c. ¿Cómo varía el resultado del punto (a), si el nivel de agua libre se localiza a
3m bajo el nivel de apoyo del cimiento?
d. ¿Cómo varía el resultado del punto (b), si el nivel de agua libre se localiza a
3m bajo el nivel de apoyo del cimiento?
22. Un edificio se apoyará sobre arcillas de origen lacustre, mediante una placa de
cimentación de 30m x 30m que recibirá todas las cargas del sistema estructural
sismo-resistente, a 1.50m bajo la superficie del terreno (ver figura 22). La carga
muerta es 6 KN/m2 y la carga viva es 5KN/m2, por placa de entrepiso en el edificio.
Los parámetros de diseño de resistencia y rigidez de los materiales, así como el
perfil de análisis geotécnico obtenido a partir de los registros estratigráficos de los
sondeos, se presenta en la tabla 22.1. El nivel freático se localiza a 1.50m bajo la
superficie del terreno.
Peso
Relación Módulo de Cv
Profundidad unitario
Material de Elasticidad (eo) RSC Cc Cr (m2/s)
(tope y base) m total
Poisson (kPa)
(KN/m3)
Arena
-
Arcillosa 0.00 / 1.50 19 0.35 15000 - - - -
(SC)
1.9 x 10-8
Arcilla (CH) 1.50 / 20.00 17 0.45 10000 1.5 1.2 1.5 0.10
Gravas y
-
arenas (SP 20.00/ 30.00 22 0.30 50000 - - - -
y GP)
Ángulo de resistencia
Cohesión no drenada al corte drenado
Profundidad Cohesión drenada (criterio
Material promedio (comportamiento (criterio Möhr-
(tope y base) m Möhr-Coulomb)
aparente) – kPa Coulomb)
Arena
30
Arcillosa 0.00 / 1.50 - -
(SC)
24
Arcilla (CH) 1.50 / 20.00 25 10
Gravas y
35
arenas (SP 20.00/ 30.00 - -
y GP)
Figura 22. Esquema de distribución del edificio y placa de cimentación a -1.50m.
Si el factor de seguridad indirecto mínimo contra la falla por capacidad portante es 3.0:
23. De acuerdo a la siguiente figura, encontrar el valor de B para el cual se logre soportar
la carga de 1000 kN aplicada, teniendo en cuenta un factor de seguridad igual a 3.
De igual manera calcular los asentamientos elásticos y por consolidación para el
estrato arcilloso. Si los asentamientos producidos son mayores a los admisibles,
proponer la relación más óptima para cumplir con las solicitaciones.