Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Operación de viaje
1. Coloque la máquina en un suelo nivelado.
2. Detenga el motor.
3. Libere la presión en el sistema hidráulico. Consulte Prueba y ajuste, "Presión del sistema hidráulico: liberación".
Ilustración 1 g00860741
Compartimento de la bomba
(1) Toma de presión (presión de entrega de la bomba derecha)
(2) Toma de presión (presión de entrega de la bomba izquierda)
4. Conecte un manómetro de 60000 kPa (8700 psi) a las tomas de presión (1) y (2).
Ilustración 2 g00860769
(3) Tornillo de ajuste
(4) Contratuerca
(5) Tapón de ajuste
(6) Contratuerca
(7) Válvula de alivio principal
Ilustración 3 g00860753
(8) Conjunto de bloque de cadenas FT-2542
(9) Piñón
5. Coloque el conjunto del bloque de cadenas (8) en la rueda dentada (9) para bloquear el desplazamiento hacia adelante a la izquierda.
7. Coloque los controles de la máquina en los siguientes ajustes: selector de velocidad del motor "10" y el interruptor de ralentí bajo en la
posición OFF. Consulte Prueba y ajuste, "Rendimiento del motor - Prueba" para conocer las configuraciones de rpm del motor.
10. Slowly move the left travel control lever to full FORWARD position and check the pressure gauge reading at pressure tap (2). The
pressure setting should be 34300 ± 490 kPa (4950 ± 72 psi). If the pressure gauge reading is not 34300 ± 490 kPa (4950 ± 72 psi), the
relief valve must be adjusted.
11. In order to adjust the relief valve, perform the following steps:
12. Repeat step 10 and step 11 until the pressure gauge is set to the correct reading.
Implement Operation
1. Position the machine on level ground.
3. Release the pressure in the hydraulic system. Refer to Testing And Adjusting, "Hydraulic System Pressure - Release".
Illustration 4 g00860741
Pump compartment
(1) Pressure tap (right pump delivery pressure)
(2) Pressure tap (left pump delivery pressure)
4. Attach a 60000 kPa (8700 psi) pressure gauge to pressure taps (1) and (2).
Illustration 5 g00860769
(3) Adjustment screw
(4) Locknut
(5) Plunger
(6) Locknut
(7) Main relief valve
9. Slowly move the joystick for the stick to the STICK IN position. Hold the joystick for the stick in the position and check the pressure gauge
reading at pressure tap (2). The pressure setting should be 29900 ± 490 kPa (4350 ± 72 psi). If the pressure reading is not
29900 ± 490 kPa (4350 ± 72 psi), the relief valve must be adjusted.
10. In order to adjust the relief valve, perform the following steps:
c. Repeat step 9.
11. Repeat step 9 and step 11 until the pressure gauge is set to the correct reading.
12. Return the joystick for the stick to the NEUTRAL position.
Illustration 6 g00860769
(3) Adjustment screw
(4) Locknut
(5) Adjustment plug
(6) Locknut
(7) Main relief valve
PPI-00011A92
2021/10/05
21: 57: 56-05: 00
i01666584
© 2021 Caterpillar Inc.
Caterpillar:
Confidential Green