Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Se diseñara una vivienda unifamiliar de tres niveles siguiendo las pautas y consideraciones desarrolladas en las
clases.
ESTRUCTURACIÓN PRELIMINAR
Se asigna los datos requeridos a la hoja de cálculo para verificar el mínimo de densidad de muros en ambas
direcciones como lo estipula la Norma E.070
En ambas direcciones de análisis se comprueba que cumplen el mínimo de densidad de muros portantes.
MODELADO ETABS
DEFINICION DE PROPIEDADES DE MATERIAL
DEFINICION DE SECCIONES
MODELADO DE LA EDIFICACION EN ETABS
-No presenta dado que las aberturas son inferiores al 50% del área total bruta del diafragma.
PESO SISMICO
EL RANGO DEL RATIO PARA EDIFICIO TIPO "C" DEBE ESTAR POR LOS 1000 KG/M2
PARAMETROS PARA EL ANALISIS SISMICO ESTATICO EN LA DIRECCION EN X
TX= 0.09 S
Z= 0.45 Zona 4-Lima
S= 1.05 Suelo S2
TP= 0.6
TL= 2
U= 1 TIPO "C" Vivienda
C= 2.5
Ro= 3 Albañilería Confinada Ro=3
Ia= 1 Verificar
Ip= 1 Verificar
VEXX= 104.019
Tx= 0.09
k= 1
TY= 0.147 S
Z= 0.35 Zona 4-Lima
S= 1.05 Suelo S2
TP= 0.6
TL= 2
U= 1 TIPO "C" Vivienda
C= 2.5
Ro= 3 Albañilería Confinada Ro=3
Ia= 1 Verificar
Ip= 1 Verificar
VERIFICACIÓN ETABS:
Los valores difieren del cálculo manual aproximadamente en 10 toneladas dado que el cálculo de sismo estatico
en Etabs no es preciso.
ANALISIS SISMICO DINAMICO
Definición del espectro de respuesta de la Norma E.030 y los casos de carga de sismo dinámico en ambas
direcciones X y Y.
CONSIDERANDO UNA ZONA SISMICA DE Z4, SUELO S2 Y UNA EDIFICACION DESTINADA A VIVIENDA
Z 0.45
TP (s) 0.6
TL (s) 2
Factor de suelo "S" 1.05
Factor de Uso "U" 1
Rx 3 FALTA VERIFICAR
Ry 3 FALTA VERIFICAR
FACTOR=ZUSg/R 1.545075
T C Sa Sa(g)
0 2.5 3.8626875 0.39375
0.1 2.5 3.8626875 0.39375
0.2 2.5 3.8626875 0.39375
0.3 2.5 3.8626875 0.39375
0.4 2.5 3.8626875 0.39375
0.5 2.5 3.8626875 0.39375
0.6 2.5 3.8626875 0.39375
0.7 2.142857 3.310875 0.3375
0.8 1.875 2.897015625 0.295313
0.9 1.666667 2.575125 0.2625
1 1.5 2.3176125 0.23625
1.1 1.363636 2.106920455 0.214773
1.2 1.25 1.93134375 0.196875
1.3 1.153846 1.782778846 0.181731
1.4 1.071429 1.6554375 0.16875
1.5 1 1.545075 0.1575
1.6 0.9375 1.448507813 0.147656
1.7 0.882353 1.363301471 0.138971
1.8 0.833333 1.2875625 0.13125
1.9 0.789474 1.219796053 0.124342
2 0.75 1.15880625 0.118125
2.1 0.680272 1.051071429 0.107143
2.2 0.619835 0.957691116 0.097624
2.3 0.567108 0.876224008 0.089319
2.4 0.520833 0.804726563 0.082031
2.5 0.48 0.741636 0.0756
2.6 0.443787 0.685684172 0.069896
2.7 0.411523 0.635833333 0.064815
2.8 0.382653 0.591227679 0.060268
2.9 0.356718 0.551156361 0.056183
3 0.333333 0.515025 0.0525
3.1 0.312175 0.482333507 0.049168
3.2 0.292969 0.452658691 0.046143
3.3 0.275482 0.425640496 0.043388
3.4 0.259516 0.400971021 0.040874
3.5 0.244898 0.378385714 0.038571
3.6 0.231481 0.35765625 0.036458
3.7 0.219138 0.338584733 0.034514
3.8 0.207756 0.320998961 0.032722
3.9 0.197239 0.304748521 0.031065
4 0.1875 0.289701563 0.029531
4.1 0.178465 0.275742118 0.028108
4.2 0.170068 0.262767857 0.026786
4.3 0.16225 0.25068821 0.025554
4.4 0.154959 0.239422779 0.024406
4.5 0.148148 0.2289 0.023333
4.6 0.141777 0.219056002 0.02233
4.7 0.135808 0.209833635 0.02139
4.8 0.130208 0.201181641 0.020508
4.9 0.124948 0.193053936 0.019679
5 0.12 0.185409 0.0189
ANALISIS SISMICO DINAMICO EN ETABS
SISMO DINAMICO EN X
SISMO DINAMICO EN Y
VERIFICACION DE DERIVAS EN X Y EN Y
DERIVA XX
Story Output Case Step Type Direction Drift Label X Y Z
m m m DMAX=0.005
NIVEL 3 DERIVA X Max X 0.000221 7 11.85 5.85 8.9 CUMPLE
NIVEL 2 DERIVA X Max X 0.000306 7 11.85 5.85 6.2 CUMPLE
NIVEL 1 DERIVA X Max X 0.000294 7 11.85 5.85 3.5 CUMPLE
DERIVA YY
Story Output Case Step Type Direction Drift Label X Y Z
m m m DMAX=0.005
NIVEL 3 DERIVA Y Max Y 0.000915 20 0 0 8.9 CUMPLE
NIVEL 2 DERIVA Y Max Y 0.001106 20 0 0 6.2 CUMPLE
NIVEL 1 DERIVA Y Max Y 0.000946 20 0 0 3.5 CUMPLE
IRREGULARIDAD EN TORSION
No se realiza el cálculo de la irregularidad en torsión debido a que las derivas no superan el 50% del máximo
permitido en la norma, pero se verifica por recomendación.
IRREGULARIDAD TORSION XX
Story Output Case Case Type Step Type Item Max Drift Avg Drift Ratio Label Max Loc X Max Loc Y Max Loc Z
NIVEL 3 DERIVA X Combination Max Diaph D3 X 0.000221 0.000215 1.03 7 11.85 5.85 8.9 NO HAY TORSION EN X-X
NIVEL 2 DERIVA X Combination Max Diaph D2 X 0.000306 0.000295 1.03 7 11.85 5.85 6.2 NO HAY TORSION EN X-X
NIVEL 1 DERIVA X Combination Max Diaph D1 X 0.000294 0.000281 1.05 7 11.85 5.85 3.5 NO HAY TORSION EN X-X
IRREGULARIDAD TORSION YY
Story Output Case Case Type Step Type Item Max Drift Avg Drift Ratio Label Max Loc X Max Loc Y Max Loc Z
NIVEL 3 DERIVA Y Combination Max Diaph D3 Y 0.00092 0.000661 1.39 20 0 0 8.9 HAY TORSION EN Y-Y
NIVEL 2 DERIVA Y Combination Max Diaph D2 Y 0.00111 0.000786 1.41 20 0 0 6.2 HAY TORSION EN Y-Y
NIVEL 1 DERIVA Y Combination Max Diaph D1 Y 0.00095 0.00066 1.43 20 0 0 3.5 HAY TORSION EN Y-Y
JUNTA SISMICA
JUNTA SÍSMICA
Junta
2/3 D max
Dirección D max (cm) S/2 (cm) Sísmica
(cm)
(cm)
Dirección X-X 0.24 0.16 2.67 3.00
Dirección Y-Y 0.87 0.58 2.67 3.00
CORTANTE BASAL DE DISEÑO
CARACTERISTICAS DE LA ALBAÑILERIA
SISMO MODERADO X y Y
P V2 V3 T M2 M3
Story Pier Output Case Case Type Step Type Location
kgf kgf kgf kgf-m kgf-m kgf-m
NIVEL 1 MX 1 SXMOD Combination Max Bottom 1975.82 15278.36 2.96 35.09 6.38 48556.32
NIVEL 1 MX 2 SXMOD Combination Max Bottom 422.79 2076.03 1.29 1.68 0.09 4436.4
NIVEL 1 MX 3 SXMOD Combination Max Bottom 29.04 1658.37 0.79 1.69 0.21 3360.29
NIVEL 1 MX 4 SXMOD Combination Max Bottom 449.91 1247.72 0.83 1.05 0.07 2446.88
NIVEL 1 MX 5 SXMOD Combination Max Bottom 917.88 1795.21 3.03 1.4 1.71 3505.41
NIVEL 1 MX 6 SXMOD Combination Max Bottom 228.83 2161.05 1.66 1.83 0.2 4685.56
NIVEL 1 MX 7 SXMOD Combination Max Bottom 1073.08 1091.52 0.4 1.06 0.79 2128.07
NIVEL 1 MX 8 SXMOD Combination Max Bottom 1178.33 13906.95 2.1 21.13 3.46 47409.56
NIVEL 1 MY 1 SXMOD Combination Max Bottom 931.97 525.87 1.58 0.96 0.07 871.37
NIVEL 1 MY 2 SXMOD Combination Max Bottom 106.34 445.41 7.16 2.07 16.67 850.04
NIVEL 1 MY 3 SXMOD Combination Max Bottom 426.19 396.38 7.27 1.77 8.03 698.27
NIVEL 1 MY 4 SXMOD Combination Max Bottom 212.37 240.79 5.84 2.01 4.7 510.56
NIVEL 1 MY 5 SXMOD Combination Max Bottom 359.82 327.92 6.88 2.27 8.02 671.34
NIVEL 1 MY 6 SXMOD Combination Max Bottom 466.43 350.09 3.73 1.29 5.54 646.31
NIVEL 1 MY 7 SXMOD Combination Max Bottom 4262.01 2865.91 10.48 8.5 14.94 6069.84
P V2 V3 T M2 M3
Story Pier Output Case Case Type Step Type Location
kgf kgf kgf kgf-m kgf-m kgf-m
NIVEL 1 MX 1 SYMOD Combination Max Bottom 11607.94 8512.52 47.08 65.6 84.91 27651.74
NIVEL 1 MX 2 SYMOD Combination Max Bottom 169.92 506.6 14.36 3.77 0.79 904.19
NIVEL 1 MX 3 SYMOD Combination Max Bottom 129.09 392.09 7.06 4.03 0.38 703.07
NIVEL 1 MX 4 SYMOD Combination Max Bottom 891.08 373.69 7.58 3.31 0.42 600.81
NIVEL 1 MX 5 SYMOD Combination Max Bottom 4028.11 742.69 14.28 6.34 18.48 908.75
NIVEL 1 MX 6 SYMOD Combination Max Bottom 45.21 133.9 7.48 6.34 0.33 299.69
NIVEL 1 MX 7 SYMOD Combination Max Bottom 1039.56 136.96 6.75 4.83 12.91 334.55
NIVEL 1 MX 8 SYMOD Combination Max Bottom 16119.94 8834.25 42.54 44.35 81.3 21113.78
NIVEL 1 MY 1 SYMOD Combination Max Bottom 2978.02 3126.93 2.13 1.69 0.1 5667.62
NIVEL 1 MY 2 SYMOD Combination Max Bottom 1486.39 6285.5 1.14 7.65 4.4 13622.34
NIVEL 1 MY 3 SYMOD Combination Max Bottom 881.32 5309.24 4.84 4.66 4.63 10493.17
NIVEL 1 MY 4 SYMOD Combination Max Bottom 287.22 4981.5 1.67 7.66 3.25 10636.12
NIVEL 1 MY 5 SYMOD Combination Max Bottom 496.51 3038.97 4.41 4.95 4.63 6318.77
NIVEL 1 MY 6 SYMOD Combination Max Bottom 401.35 1379.06 1.61 3.33 2.97 2717.78
NIVEL 1 MY 7 SYMOD Combination Max Bottom 520.85 8008.31 0.77 22.29 0.81 23867.57
SISMO SEVERO X y Y
P V2 V3 T M2 M3
Story Pier Output Case Case Type Step Type Location
kgf kgf kgf kgf-m kgf-m kgf-m
NIVEL 1 MX 1 SXSEV Combination Max Bottom 3951.64 30556.73 5.91 70.18 12.77 97112.63
NIVEL 1 MX 2 SXSEV Combination Max Bottom 845.58 4152.06 2.59 3.35 0.17 8872.8
NIVEL 1 MX 3 SXSEV Combination Max Bottom 58.08 3316.74 1.57 3.38 0.42 6720.57
NIVEL 1 MX 4 SXSEV Combination Max Bottom 899.82 2495.44 1.66 2.11 0.14 4893.76
NIVEL 1 MX 5 SXSEV Combination Max Bottom 1835.75 3590.42 6.07 2.8 3.41 7010.82
NIVEL 1 MX 6 SXSEV Combination Max Bottom 457.65 4322.11 3.32 3.67 0.4 9371.12
NIVEL 1 MX 7 SXSEV Combination Max Bottom 2146.15 2183.03 0.8 2.13 1.59 4256.15
NIVEL 1 MX 8 SXSEV Combination Max Bottom 2356.65 27813.89 4.19 42.25 6.93 94819.11
NIVEL 1 MY 1 SXSEV Combination Max Bottom 1863.93 1051.74 3.15 1.92 0.14 1742.73
NIVEL 1 MY 2 SXSEV Combination Max Bottom 212.68 890.81 14.33 4.14 33.35 1700.08
NIVEL 1 MY 3 SXSEV Combination Max Bottom 852.38 792.77 14.54 3.55 16.05 1396.53
NIVEL 1 MY 4 SXSEV Combination Max Bottom 424.74 481.58 11.68 4.03 9.39 1021.13
NIVEL 1 MY 5 SXSEV Combination Max Bottom 719.64 655.84 13.77 4.54 16.04 1342.67
NIVEL 1 MY 6 SXSEV Combination Max Bottom 932.86 700.19 7.47 2.58 11.08 1292.62
NIVEL 1 MY 7 SXSEV Combination Max Bottom 8524.02 5731.81 20.95 17 29.88 12139.67
P V2 V3 T M2 M3
Story Pier Output Case Case Type Step Type Location
kgf kgf kgf kgf-m kgf-m kgf-m
NIVEL 1 MX 1 SYSEV Combination Max Bottom 23215.88 17025.04 94.15 131.21 169.82 55303.47
NIVEL 1 MX 2 SYSEV Combination Max Bottom 339.83 1013.2 28.73 7.53 1.59 1808.37
NIVEL 1 MX 3 SYSEV Combination Max Bottom 258.17 784.18 14.13 8.06 0.75 1406.14
NIVEL 1 MX 4 SYSEV Combination Max Bottom 1782.15 747.38 15.15 6.61 0.84 1201.62
NIVEL 1 MX 5 SYSEV Combination Max Bottom 8056.22 1485.39 28.55 12.68 36.95 1817.49
NIVEL 1 MX 6 SYSEV Combination Max Bottom 90.41 267.81 14.97 12.68 0.66 599.39
NIVEL 1 MX 7 SYSEV Combination Max Bottom 2079.11 273.92 13.51 9.66 25.82 669.09
NIVEL 1 MX 8 SYSEV Combination Max Bottom 32239.88 17668.51 85.08 88.69 162.59 42227.56
NIVEL 1 MY 1 SYSEV Combination Max Bottom 5956.03 6253.87 4.27 3.38 0.2 11335.24
NIVEL 1 MY 2 SYSEV Combination Max Bottom 2972.79 12570.99 2.28 15.29 8.8 27244.69
NIVEL 1 MY 3 SYSEV Combination Max Bottom 1762.65 10618.47 9.68 9.32 9.26 20986.35
NIVEL 1 MY 4 SYSEV Combination Max Bottom 574.43 9963.01 3.34 15.33 6.5 21272.25
NIVEL 1 MY 5 SYSEV Combination Max Bottom 993.01 6077.94 8.82 9.89 9.27 12637.54
NIVEL 1 MY 6 SYSEV Combination Max Bottom 802.7 2758.11 3.21 6.65 5.93 5435.56
NIVEL 1 MY 7 SYSEV Combination Max Bottom 1041.7 16016.62 1.54 44.58 1.62 47735.14
30250.65 15278.36 48556.32 47.08 84.91 15278.36 48556.32 3.776 1.000 79857.6495 NO FISURADO
6779.11 2076.03 4436.40 14.36 0.79 2076.03 4436.4 1.240 1.000 17657.9453 NO FISURADO
5643.63 1658.37 3360.29 7.06 0.38 1658.37 3360.29 1.061 1.000 14359.2849 NO FISURADO
4571.30 1247.72 2446.88 7.58 0.42 1247.72 2446.88 0.867 0.867 10003.9868 NO FISURADO
4612.11 1795.21 3505.41 14.28 18.48 1795.21 3505.41 1.127 1.000 14425.7853 NO FISURADO
8448.34 2161.05 4685.56 7.48 0.33 2161.05 4685.56 1.291 1.000 18953.1182 NO FISURADO
3273.52 1091.52 2128.07 6.75 12.91 1091.52 2128.07 0.859 0.859 9495.12883 NO FISURADO
29769.16 13906.95 47409.56 42.54 81.30 13906.95 47409.56 3.520 1.000 79746.9068 NO FISURADO
2449.46 1.58 0.07 3126.93 5667.62 3126.93 5667.62 0.717 0.717 6227.73025 NO FISURADO
5893.64 7.16 16.67 6285.50 13622.34 6285.50 13622.34 1.292 1.000 18365.5372 NO FISURADO
5380.38 7.27 8.03 5309.24 10493.17 5309.24 10493.17 1.164 1.000 15209.9874 NO FISURADO
6642.13 5.84 4.70 4981.50 10636.12 4981.50 10636.12 1.311 1.000 18537.6899 NO FISURADO
5711.40 6.88 8.02 3038.97 6318.77 3038.97 6318.77 1.106 1.000 15286.122 NO FISURADO
3491.03 3.73 5.54 1379.06 2717.78 1379.06 2717.78 0.837 0.837 9195.2762 NO FISURADO
13584.57 10.48 14.94 8008.31 23867.57 8008.31 23867.57 2.013 1.000 39574.4511 NO FISURADO
DISEÑO POR RESISTENCIA-SISMO SEVERO
VEi - X VEi - Y VEi
(kg) (kg) (kg)
Para evitar la falla frágil se incremento el espesor del muro 1 en la dirección de y de 0.15 cm a 0.25 cm.
DETERMINACION DE REFUERZO HORIZONTAL
CONDICIÓN
(kg) (kg-m)
5.226846959 3 45835.08 145668.96 NO NECESITA REFUERZO
8.505631084 3 6228.09 13309.2 NO NECESITA REFUERZO
8.658673818 3 4975.11 10080.87 NO NECESITA REFUERZO
8.017813957 3 3743.16 7340.64 NO NECESITA REFUERZO
8.035709081 3 5385.63 10516.23 NO NECESITA REFUERZO
8.770328405 3 6483.15 14056.68 NO NECESITA REFUERZO
8.69899666 3 3274.56 6384.21 NO NECESITA REFUERZO
5.734320379 3 41720.85 142228.68 NO NECESITA REFUERZO
685.82127 527.555 2 1.3 0.65 1224.73 3113.87 -697.18 1752.28 0.8 4ф8mm 2.012 -48.0 104.7 375.0 375.0 25 29 30 15
8397.9052 2999.25 3 1.7 1.4 1964.55 4181.44 1034.71 4963.80 0.8 4ф8mm 2.012 -9.4 140.6 375.0 375.0 25 29 30 15
4051.9064 1761.7 2 2.3 1.15 2690.19 7604.99 -928.49 4451.89 0.8 4ф8mm 2.012 -15.6 255.6 375.0 375.0 25 29 30 15
208.91027 74.6108 3 1.7 1.4 2214.04 4220.63 -2139.43 2288.65 0.8 4ф8mm 2.012 -41.5 141.9 375.0 375.0 25 29 30 15
-7182.9586 3123.03 2 2.3 1.15 2855.7 7643.06 267.33 5978.73 0.8 4ф8mm 2.012 2.8 256.9 375.0 375.0 25 29 30 15
-7570.5823 4588.23 2 1.65 0.825 1745.52 4597.64 2842.72 6333.75 0.8 4ф8mm 2.012 7.0 154.5 375.0 375.0 25 29 30 15
3930.3986 655.066 4 2.82 3 3396.14 5936.17 -2741.08 4051.21 0.8 4ф8mm 2.012 -20.4 199.5 375.0 375.0 25 29 30 15
390 CUMPLE 450 3.00 1.20 1.88 4.20 4.20 4 φ1/2" 5.16
390 CUMPLE 450 3.09 0.84 1.88 3.93 3.93 4 φ1/2" 5.16
390 CUMPLE 450 2.51 1.10 1.88 3.61 3.61 4 φ1/2" 5.16
390 CUMPLE 450 1.75 0.97 1.88 2.72 2.72 4 φ3/8" 2.84
390 CUMPLE 450 2.53 1.16 1.88 3.68 3.68 4 φ1/2" 5.16
390 CUMPLE 450 3.32 0.65 1.88 3.97 3.97 4 φ1/2" 5.16
390 CUMPLE 450 1.66 1.19 1.88 2.85 2.85 4 φ1/2" 5.16
390 CUMPLE 450 2.99 1.25 1.88 4.24 4.24 4 φ1/2" 5.16
650 CUMPLE 750 1.75 0.90 3.13 2.65 3.13 4 φ3/8" 2.84
390 CUMPLE 450 1.46 0.29 1.88 1.75 1.88 4 φ3/8" 2.84
390 CUMPLE 450 2.66 0.26 1.88 2.92 2.92 4 φ1/2" 5.16
390 CUMPLE 450 1.48 0.60 1.88 2.08 2.08 4 φ3/8" 2.84
390 CUMPLE 450 2.68 0.07 1.88 2.75 2.75 4 φ3/8" 2.84
390 CUMPLE 450 1.61 0.80 1.88 2.41 2.41 4 φ3/8" 2.84
390 CUMPLE 450 2.08 0.77 1.88 2.85 2.85 4 φ1/2" 5.16
tn S1 S2 S3 S4 S final 45cm ó
Distribución Refuerzo de Estribos
(cm) (cm) (cm) (cm) (cm) (cm) 1.5d
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢8mm,9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
21 14 5 7 10 5 45 ▢8mm,9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢8mm,9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢8mm,9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢8mm,9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢8mm,9@5cm,Rto@25cm C/E
11 27 10 7 10 7 45 ▢3/8",9@5cm,Rto@25cm C/E
Se exporta la planta típica del Etabs al Safe con la CM y la CV, en el mismo Safe se define la combinación ultima
CU=1.4 CM +1.7 CV para el diseño de la losa.
Se define las líneas para seccionar en áreas tributarias para el calculo de cada vigueta.
La deflexión máxima permisible es de 379 /120 = 3.16 cm por lo que se concluye que cumple.
Momentos en losas aligeradas X y Y resectivamente,
ASIGNACION DE ACERO DEL SAFE CON VARILLAS DE 3/8” EN LA PARTE INFERIOR Y SUPERIOR(ACERO POSITIVO
Y NEGATIVO)
Los aceros negativos se colocarán como bastones de acuerdo a la luz libre de losa para el paño en cuestión se
tiene: Ln=2.3 m entonces Ln1=0.46m0.50m y Ln2=0.76m0.80m
0.50m
0.80m
ACERO DE TEMPERATURA
El acero de temperatura se coloca perpendicular al sentido de las viguetas con la finalidad de resistir los esfuerzos
de contracción y temperatura del aligerado. Este acero no requiere un cálculo para el diseño, pues es de menor
diámetro que los refuerzos diseñados a flexión. Por convención se instala varillas de ø1/4” @ 0.25 m