Documentos de Académico
Documentos de Profesional
Documentos de Cultura
1
Ingeniería civil. 2135121. MSUB+9. Johan.mora@mail.escuelaing.edu.co
2
Ingeniería civil. 2114520. MSUB+9. Juan.guarnizo@mail.escuelaing.edu.co
3
Ingeniería civil. 2108429. MSUB+9. Juan.gamboa@mail.escuelaing.edu.co
1
ESCUELA COLOMBIANA DE INGENIERÍA JULIO GARAVITO
CENTRO DE ESTUDIOS GEOTÉCNICOS
LABORATORIO DE MECÁNICA DE SUELOS BÁSICA
PRIMER SEMESTRE 2019
Abstract:
In this laboratory the direct cutting test shall be carried out, in which the procedure
is performed to determine the shear resistance of a consolidated and drained soil
sample.
The test initially consisted of taking the sample, carving it and placing it in the
chamber. It was later placed and adjusted in the machine, where a normal force was
applied to determine which drained the sample (consolidation of the sample).
Subsequently, the cut was applied, whereby one half of the sample was moved
horizontally from the other at a constant rate of deformation. Meanwhile, the cutting
force and normal and horizontal shifts were recorded.
The test results are applicable to estimate the shear strength in a field situation
where complete consolidation has taken place under current normal stresses.
Keywords:
Fault, Soil, Surfice of fault, Desplazamiento lateral relativo, Norlam force, Shear
force.
2
ESCUELA COLOMBIANA DE INGENIERÍA JULIO GARAVITO
CENTRO DE ESTUDIOS GEOTÉCNICOS
LABORATORIO DE MECÁNICA DE SUELOS BÁSICA
PRIMER SEMESTRE 2019
2. METODOLOGÍA
Se realizó una pequeña inspección manual y visual del material, identificando las
características del suelo a el cual se realizará el procedimiento.
Para el ensayo de corte directo se utilizó una arena la cual facilitaba su rápida
consolidación, ya que el exceso de presión de agua se disipa rápidamente. Se
toman las dimensiones de la caja en la cual se va a confinar la muestra de suelo.
Luego de esto se ubica la muestra en una cámara, la cual debe estar confinada
entre piedras porosas, y se ubica la cámara dentro del equipo de corte para la toma
de las medidas.
3
ESCUELA COLOMBIANA DE INGENIERÍA JULIO GARAVITO
CENTRO DE ESTUDIOS GEOTÉCNICOS
LABORATORIO DE MECÁNICA DE SUELOS BÁSICA
PRIMER SEMESTRE 2019
3. DATOS Y RESULTADOS
Se toman los siguientes datos como iniciales:
4
ESCUELA COLOMBIANA DE INGENIERÍA JULIO GARAVITO
CENTRO DE ESTUDIOS GEOTÉCNICOS
LABORATORIO DE MECÁNICA DE SUELOS BÁSICA
PRIMER SEMESTRE 2019
Aquí se deben presentar todos los datos tomados durante la práctica. Deben
presentarse DE FORMA MUY ORDENADA, COMPRENSIBLE Y CON TODAS LAS
UNIDADES.
Una ves presentados los datos tomados se procede a mostrar los cálculos
realizados con ellos, deben ser claros y SE DEBEN PRESENTAR TODAS LAS
ECUACIONES UTILIZADAS, ASÍ COMO EJEMPLOS DE CÁLCULOS. Ejemplos de
lo anterior de muestra en la Ecuación 1.
5
ESCUELA COLOMBIANA DE INGENIERÍA JULIO GARAVITO
CENTRO DE ESTUDIOS GEOTÉCNICOS
LABORATORIO DE MECÁNICA DE SUELOS BÁSICA
PRIMER SEMESTRE 2019
𝜏 = 𝑐 ′ + 𝜎 ′ ∗ tan 𝜑
.
5. CASO PRÁCTICO DE APLICACIÓN
“No aplica”
6. CONCLUSIONES Y RECOMENDACIONES
Basándose en los objetivos planteados y en los resultados obtenidos se deben
generar conclusiones y recomendaciones ingenieriles.
BIBLIOGRAFÍA
[1] Bojacá Torres, D. (2019). ENSAYO DE CORTE DIRECTO.
[2] ENSAYO DE CORTE DIRECTO EN CONDICIÓN CONSOLIDADA DRENADA (CD).E - 154.
6
ESCUELA COLOMBIANA DE INGENIERÍA JULIO GARAVITO
CENTRO DE ESTUDIOS GEOTÉCNICOS
LABORATORIO DE MECÁNICA DE SUELOS BÁSICA
PRIMER SEMESTRE 2019