Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Volumen 2 PDF
Volumen 2 PDF
Cañas
Veladero
OMM/EPR
Mayo 2004
AB Transmission-Consult
Rutherford, NJ, USA
EMPRESA PROPIETARIA DE LA RED
SIEPAC
Informe Final
Mayo 2004
AB Transmission-Consult
Rutherford, NJ, USA
ANEXO 2
(Vol. II)
ANEXO 3
(Vol. II)
ANEXO 6
(Vol. II)
EMPRESA PROPIETARIA DE LA LINEA
EPR
1. ACTO INAUGURAL
2. DISCUSIÓN DE LA AGENDA
3. PARTICIPANTES
4. OBJETIVOS DE LA REUNIÓN.
El objetivo de este taller es conocer los criterios de cada empresa con respecto
a los temas en estudio, también intercambiar experiencias que ayuden a
completar dicho estudio, y escuchar las opiniones del Consultor, luego de
haber efectuado la revisión de los documentos que le fueron entregados,
específicamente los informes de DPC, Ingendesa, y estudios de EPR.
5. DESARROLLO DE LA REUNIÓN
J. Transposiciones.
7. ACUERDOS
8. CLAUSURA
(Vol. II)
Comentarios recibidos de ETESA
Hasta el año 1995 nuestras líneas de transmisión fueron diseñadas tradicionalmente basadas
en los requerimientos del NESC. Después de este año, en el diseño de la nueva línea de
transmisión de 230 KV que se está construyendo se aceptaron los requerimientos del IEC
826 y CIGRÉ SC22, pero con un poco de reserva, porque estas normas utilizan métodos
probabilísticos, que según el período de retorno del viento puede resultar presiones de
viento sobre los conductores menores que lo señalado por el NESC.
En Costa Rica usted concluyó que se adoptará para el proyecto una velocidad de viento de
100 km/hr, que representa una presión de viento de 44 kg/m2 y un factor de sobrecarga de
1.5. Lo que me preocupa que esto constituye una presión total de viento de 66 kg/m2
aplicados directamente a los conductores, y que resulta menor a lo utilizado en Panamá (por
ETESA), como se podrá aprecia a continuación.
Según el NESC
Con el propósito de adecuar los datos ambientales disponibles en Panamá a nuestras líneas
de transmisión, se utilizaron los registros de datos de viento de que dispone ETESA.. Estos
registros de datos de viento corresponden a valores de velocidades máximas de ráfagas de
viento (velocidad instantánea) medidos a una altura de 10 metros, para las diversas
estaciones meteorológicas existentes en Panamá. Estos datos corresponden a un período
comprendido entre 1971 y 1995 y permiten su modelado para el uso con seguridad, dentro
de los procedimientos del IEC 826, que recomiendan la existencia de mediciones en el
período de, por lo menos, 20 años.
De acuerdo con los criterios del IEC 826, las velocidades de ráfaga pueden ser consideradas
dentro de un período de integración de 3 segundos. Para la conversión de estos datos para
el período de integración de 10 minutos fue utilizado el gráfico correspondiente indicado
por el IEC 826. Con estos valores, es posible entonces, siguiendo los procedimientos del
IEC 826, determinar la velocidad de referencia para la línea de transmisión, la cual es 30.0
m/s (108 km/h), considerando un período de retorno de 500 años, y las siguientes presiones
de diseño:
Con respecto al viento sobre las torres, no disponemos de un valor de presión porque de
acuerdo con el IEC 826 las torres deben ser divididas en diversos paneles, siendo la fuerza
calculada sobre cada uno de ellos individualmente de acuerdo con una fórmula de la IEC
826. Este cálculo de viento lo hace el diseñador del fabricante de las torres. ¿existe alguna
manera, como lo hace el NESC, de poder especificar una presión de viento para la torre?
En Panamá el nivel isoceráunico es alto, de tal forma que a la fecha estamos utilizando para
los cálculos el valor de 150. Además, consideramos una resistividad del suelo de 1000
ohmios-m. y hasta la fecha hemos utilizado una resistencia máxima de tierra de 20 ohmios.
Este valor lo vamos a revisar, por la cantidad de rayos que caen en la Provincia de Chiriquí,
lugar donde se construirá el tramo de la línea del SIEPAC.
Para cada torre utilizamos un sistema de puesta a tierra radial básico (“crowfoot”): Desde
cada pata se extiende un conductor de compensación (“counterpoise”) de 30 metros de
longitud, consistente y las cuatro patas se interconectan. Se utiliza un conductor
copperweld 3#6 Awg. Antes de 1995 se instalaba una varilla de tierra en cada extremo de
cada conductor radial; ahora, se eliminó.
Comentarios recibidos del INDE
Participantes:
d) Para el cable de guarda propuesto el Consultor deberá indicar cuales fueron los
valores de corrientes considerados tanto para cortocircuito como para protección
frente a descargas atmosféricas y presentar el cálculo de blindaje del cable de
guarda. Asimismo, presentar la memoria de cálculo que llevó a determinar que el
cable de guarda propuesto es la mejor opción técnica y económica, respecto de otras
opciones.
2. - ESTRUCTURAS
En las hipótesis de carga, para el diseño de las torres, en las cargas de conductor
roto, el Consultor deberá considerar la ruptura de un cable de guarda y una fase por
cada circuito.
El Consultor deberá presentar las consideraciones técnicas para la definición de los
factores de seguridad en el diseño de la torres.
2.2 Torres
Para los vanos de peso y viento sugeridos, las torres de anclaje no podrían utilizar
vanos de gran longitud, lo que podría causar inconveniente en el diseño de la línea,
debido a que la mayor parte del terreno en El Salvador es montañoso.
3.- AISLADORES
ANEXO
En El Salvador debido a la topografía del terreno (la mayor parte montañoso), es necesario
que las prestaciones de las torres tengan un vano máximo de gran longitud. En el siguiente
cuadro se muestran los vanos de viento, peso y máximo, que se utilizaron en el Proyecto
Interconexión Eléctrica a 230 kV Honduras – El Salvador.
Tangente (R) Suspensión 0°- (2°) 700 460 700 280 420
(400) (240)
Ezequiel Galdamez
Presente.
Estimado Señor:
Con respecto a los conceptos vertidos en el Taller No 1 del Diseño Básico de la Línea SIEPAC, la
Unidad Ejecutora tiene los siguientes comentarios y/o observaciones acerca de la selección del
conductor:
Es importante mencionar que el requerimiento básico del Proyecto SIEPAC es que se puedan
intercambiar por lo menos 300 Mw entre pares de países. La Línea SIEPAC, junto con los sistemas
nacionales existentes y las interconexiones actuales, permitirá realizar este objetivo. Debido al
hecho de que la Línea SIEPAC se interconectara en 16 puntos del Sistema Eléctrico Regional
Centroamericano, estará en paralelo con el mismo y cuando se estén intercambiando 300 Mw entre
pares de países, la Línea SIEPAC llevara aproximadamente 150 Mw. Solamente en condiciones de
emergencia, cuando exista una contingencia simple en líneas paralelas a la Línea SIEPAC, esta será
exigida para transportar los 300 Mw. El caso del tramo Guate Norte – Panaluya - Río Lindo será
respaldado por los sistemas eléctricos de Honduras y El Salvador.
El Consultor DPC recomendó que la ampacidad necesaria del conductor debería estar en el rango de
750 a 800 amperios (Ver Numeral 9.4.3) . Basado en una temperatura máxima del conductor de 80
°C, radiación solar de 1,000 w/m², temperatura ambiente de 40 °C, 200 metros sobre el nivel del
mar y una velocidad del viento de 0.6 m/s, el Consultor DPC calculo una ampacidad de 766
amperios para el conductor Condor. (Ver Numeral 9.4).
Utilizando otros parámetros, el Consultor Beloff calcula que la ampacidad del Condor es de 831
amperios a 100 metros sobre el nivel del mar (8.5% mayor que la calculada por DPC). También
calculo que la ampacidad del conductor Condor a 2,000 metros sobre el nivel del mar era de 770
amperios.
De acuerdo a los datos del Consultor Beloff, el conductor Condor se sobrecargaría 0.7% a 100
metros y 8.7% a 2000 metros si hubiera una contingencia de las líneas paralelas a la Línea SIEPAC
y se le exigiera a la Línea SIEPAC transportar 300 Mw (837 amperios @ 0.9 pf).
En el análisis económico, el Consultor Beloff considera elegibles a los Conductores Ruddy, Rail y
1024 ACAR. El más económico desde el punto de vista de costos totales anuales es el Rail AW y
considerando que la EPR no percibiría la disminución de perdidas sino que únicamente haría frente
a los sobrecostos de inversión, el más económico desde el punto de vista de la EPR es el Ruddy.
Además, el Consultor Beloff ha considerado que la línea estaría cargada a 300 Mw y como
mencionamos anteriormente esto solo ocurriría en situaciones de contingencia.
Finalmente, deseo reiterarle la disposición de todos los órganos del Proyecto SIEPAC a colaborar
con la EPR en el desarrollo de la Línea SIEPAC.
(Vol. II)
Respuesta a comentarios de Panamá
Actualmente Panamá diseña sus líneas con una presión final de 105 kg/m2 sobre los
conductores, esto se traduciría en aproximadamente 105/72=45% mas de presión que lo
propuesto lo que resultaría en un sobrepeso de acero de 15-20% o aproximadamente 3
toneladas más por km (15% de 20 t/km), o un total de 3 t/km x 1830 km = 5500 toneladas
que al precio de $2,500 por tonelada (material y montaje) nos daría una sobre inversión en
exceso de $12,000,000, sin contar con el costo extra de las fundaciones.
Llama la atención que la aplicación lisa y rasa de las prescripciones de la NESC no tuvieron
validación efectiva a través de la investigación de vientos en la región, cuya justificación
ahora es que la velocidad de viento adoptado (siguiendo la metodología IEC 826 a la inversa)
es de 30 m/s (108 km/h) considerando un periodo de retorno de 500 años.
La línea SIEPAC no justificaría ser diseñada para un periodo de retorno de 500 años y
tampoco para un período de retorno de 150 años como fue propuesto en el informe DPC. De
ahí que la conclusión de adoptar un viento de 100 km/h directamente sobre el conductor
aparece económicamente y técnicamente correcta si se compara con las propias experiencias
de dos países tan alejados como Guatemala y Costa Rica que diseñan sus líneas para 100
km/h y 80 km/h, respectivamente con factores de carga alrededor de 1.50, con excelente
experiencia operacional. También El Salvador diseña para un viento máximo de 100 km/h
directo en los conductores.
Este es un procedimiento laborioso de gran complejidad, muy exacto pero que exige de gran
atención y cuidado al proyectista y dificulta la tarea del ingeniero revisor, es inclusive difícil
de duplicar en los modelos de pruebas a escala natural en las estaciones de ensayo de los
fabricante de estructuras.
Un ejercicio de tal precisión es innecesario y me remito a las recomendaciones del ASCE-74
donde claramente se establece que para torres hasta 200 ft (65 m) de altura es suficiente
especificar una única presión de viento calculada a la altura del centro de gravedad de la
estructura o a 2/3 de la altura total de la misma. La presión resultante así calculada es
aplicada a toda la extensión de la torre y con esto se obtiene un solo e inequívoco parámetro
de velocidad y presión de viento. En USA se utiliza un único valor de presión de viento en la
estructura.
Aclaro que solo en estructuras muy elevadas como podrían ser las grandes travesías de ríos
de llanura (caso de las travesías del río Mississippi en USA) con alturas de hasta 200 m se
aplican velocidades y presiones corregidas por altura a partir de los 60 m.
1 TRANSPOSICIONES
En la actualidad, con los sistemas en expansión y más líneas llegando a los nodos del
sistema interconectado (subestaciones), es difícil concluir en la necesidad de
transposiciones para distancias de 100 km. En los sistemas de transmisión se acepta
un cierto grado de desbalance en las reactancias e impedancias mutuas de cada fase,
esta es una condición que depende en gran parte de la configuración de conductores.
Para la línea SIEPAC, mayormente configurada en triángulo para las secciones de
circuito simple el desbalance de fases es menor aún. Longitudes de líneas de hasta
200 millas (320 km) no llevan transposiciones de línea en USA. La línea SIEPAC es
altamente seccionada y no se recomienda el uso de transposiciones. Por otra parte es
bueno resaltar que las transposiciones son puntos débiles de la línea en cuanto están
sujetas a mayor número de salidas por descargas atmosféricas que las geometrías
normales.
2 AISLADORES
Las economías de escala serán evaluadas durante el análisis de las propuestas de los
contratistas. Ellos seleccionaran en sus propuestas las opciones más económicas
conforme especificaciones de EPR.
1. CONDUCTOR
Los cálculos del consultor no avalan las conclusiones de Costa Rica referentes a las
flechas mayores encontradas para el conductor 1024 ACAR comparadas con ACSR.
El conductor propuesto tiene formación 18/19 y aparentemente Costa Rica utilizó una
formación con menor RTS. Favor verificar.
La tensión EDS 16% para el ACAR es estándar en la industria en USA y tiene bases
en las recomendaciones del CIGRE, IEEE, fabricantes de conductores (ALCOA,
ALCAN) y muchos años de aplicación exitosa.
Nada nuevo.
Nada nuevo.
6. TRANSPOSICIONES
Las justificativas para el uso de transposiciones en el tramo mas largo (234 km) deben
provenir de los estudios de comportamiento del sistema (estudios de flujos de carga),
o de los criterios de desbalance de fases de las propias compañías integrantes del
SIEPAC. Nuestra recomendación ha sido no usar transposiciones por no ser la línea
suficientemente larga para que provoque un desbalance importante entre las fases. Por
otra parte es bueno resaltar que las transposiciones son puntos débiles de la línea en
cuanto están sujetas a mayor número de salidas por descargas atmosféricas que las
geometrías normales.
7. GEOMETRIA DE LA TORRE
Respecto de los parámetros que aplica el ICE en el diseño de las líneas de transmisión
estos deben ser sometidos a apreciación del consultor. Sin embargo este no se
constituye en tema de discusión sino que sería meramente informativo.
Como ya fue indicado el uso de dos conductores por fase es considerablemente más
oneroso (15-20%) que una línea de conductor simple para una misma capacidad de
transporte. El uso de conductor doble atentaría contra el criterio de mínima inversión
que se indica en el informe DPC. Efectivamente dos conductores Flicker ofrecen una
sección transversal de conductor 2x0.846”/1.165”= 1.45 veces mayor de área
expuesta al viento y también una tensión máxima de ruptura de 2x17,200/26,700 =
1.29 veces mayor lo que hace que las estructuras sean mas pesadas en un 20 % sin
considerar el impacto económico de las fundaciones. El informe DPC descartó el uso
de dos conductores por fase y seria un ejercicio fútil considerar esta opción en el
estudio económico de conductores cuando por el contrario la Unidad Ejecutora
SIEPAC esta procurando medios de minimizar la inversión inclusive cuestionando el
uso de conductores de mayor diámetro que el Cóndor.
2. ESTRUCTURAS
3. AISLADORES
4. PUESTA A TIERRA
El tema no esta incluido en las tareas del Consultor. Sin embargo estoy de acuerdo
con el temperamento de especificar resistencias bajas de pie de torre debido a la gran
actividad atmosférica en la región que necesitará de todos los métodos posibles de
mitigación de los efectos indeseables de las descargas en el desempeño de la línea. El
uso de 5 ohms en vez de los 10 ohms especificados por DPC para la resistencia de
puesta a tierra esta siendo estudiado.
5. VIENTOS
1. VIENTOS
ENTRESA diseña sus líneas para vientos de 120 km/h (60 kg/m2, sobre los
conductores?) De acuerdo con nuestros cálculos la presión del viento sobre el
conductor debería ser de 69 kg/m2. Si fuera adoptado para la linea SIEPAC esto
significaría una sobrecarga adicional sobre conductores y estructuras de 69/48 = 1.44
veces lo que se traduciría en un sobrepeso en las estructuras de aproximadamente 15-
20% con un costo adicional para el proyecto de mas de $12,000,000, sin todavía
contar con el costo extra de las fundaciones.
El viento de 120 km/h es mayor que el utilizado en Costa Rica (80 km/h) y
Guatemala y El Salvador (100 km/h) y no se conocen registros de viento que
justifiquen elevar el viento propuesto de 100 km/h para el proyecto SIEPAC. Por
otra parte es muy importante notar que la experiencia operacional en esos tres países
ha sido excelente y no se ve la necesidad de una mayoración en los criterios de
diseño. Sería interesante saber cuales son los factores de sobrecarga utilizados por
Nicaragua en conjunción con el viento de 120 km/h.
1. CRITERIOS DE OPERACIÓN
El conductor Cóndor y todo otro conductor tienen capacidad para transportar más
de lo que normalmente son diseñados. Bastaría con cambiar la temperatura
máxima de operación, digamos de 80 oC a 90, 100 o 125 oC para aumentar
notablemente la ampacidad del mismo. Conforme recomendación de DPC la línea
SIEPAC esta diseñada para 80 oC y no podrá ser operada a temperaturas mayores
por un tiempo prolongado ya que se reducirían las libranzas al suelo y otros
obstáculos. La adopción de 80 oC de temperatura máxima del conductor es de uso
generalizado y esta de acuerdo con los criterios operacionales de los países del
SIEPAC. Operar una línea a mayores temperaturas tiene su costo económico ya
que habría que aumentar la altura de las torres. Sin embargo la línea podría ser
sobrecargada por un periodo de 20 minutos sin prácticamente infringir las
libranzas ya que los conductores demoran un tiempo para alcanzar la temperatura
de régimen (régimen transitorio) que puede durar de 30 a 60 minutos dependiendo
de la masa del conductor y del valor de la sobrecarga. De todas maneras esta
sobrecarga no podría ser superior al 25-30% de la carga normal.
Finalmente entra la naturaleza de la atmósfera: Clara con sol, o industrial, sin sol
y la latitud donde esta localizada la línea. Cuanto mas al norte mayor la
ampacidad, cuanto mas se acerca al Ecuador menor es la capacidad térmica de
transporte.
En vista que la línea SIEPAC esta localizada un 85% de su longitud por debajo de
los 1000 m podría aun considerarse el uso de un conductor diferente para el resto
de la línea situada entre los 1000 a 2000 m. Sin embargo las desventajas de crear
una segunda familia de estructuras conspira contra la economía de escala y
también complicaría los planes de materiales de repuestos y mantenimiento.
(Vol. II)
EMPRESA PROPIETARIA DE LA LINEA
EPR
Ayuda Memoria
Taller Intermedio Diseño Básico de la Línea
San José, Costa Rica, 6 de Febrero 2004.
1. ACTO INAGURAL
El Ing. Francisco Núñez, Gerente General de EPR, dio la bienvenida a los asistentes y
mencionó que el objetivo de este taller era analizar y discutir aspectos técnicos del diseño de
la línea para continuar con el estudio, asimismo recalcó que anteriormente la región aprobó un
diseño preliminar el cual era la base para que el consultor hiciera una revisión mejorando el
diseño con la información actual.
2. DISCUSIÓN DE LA AGENDA
Previamente se envió por correo electrónico la agenda a tratar con el consultor, se sometió a
consideración, la cual fue aprobada y se adjunta como Anexo No. 1.
3. PARTICIPANTES
4. OBJETIVOS DE LA REUNIÓN
El objetivo de este taller era informar del avance del estudio y analizar los aspectos técnicos
planteados por el consultor en el primer taller.
5. DESARROLLO DE LA REUNION
5.1. CONDUCTOR.
El Consultor dio una amplia explicación del por qué se cambió el conductor propuesto
en los estudios de DPC (Cóndor 795 ACSR) mencionando que los aspectos más
importantes considerados son los fenómenos corona y sus efectos eléctricos y
ambientales en las líneas de 230 kV operando a alturas que superan los 1000 metros,
adicionalmente mencionó otros beneficios de confiabilidad, seguridad y reducción de
pérdidas.
5.2 VIENTOS
Se discutió la propuesta de emplear una velocidad de 100 kph y una presión de 48 kg/m2,
dado que se ajusta en la mayor medida a la experiencia de los países.
5.3 ESTRUCTURAS
El Consultor expuso que luego de conocer el caso de las salidas de línea en las
subestaciones en Guatemala y la experiencia que este país ha tenido con el uso de postes
de concreto, se analizará como una opción su uso en casos con restricciones en el
derecho de vía.
El Consultor solicitó a los países que usarán torres de 2 circuitos (El Salvador y Costa
Rica) revisar las prestaciones (vanos) propuestas para dichas estructuras.
• Hipótesis de carga (este tema no se envió antes de la reunión, el material será remitido
a los países):
o Contención de falla: Se define para evitar la propagación de una falla por rotura
de un conductor o un hilo de guarda a la vez (sin viento). El coeficiente es de 1.2.
(Hará el efecto necesario para evitar la cascada).
Con respecto a las torres intermedias en tangentes largas se analizará el caso de Nicaragua
donde hay una tangente de más de 20 km.
7. RECOMENDACIONES
8. CONCLUSIONES
2. Aceptar que la velocidad de viento a la altura de los conductores será de 100 km/h
lo que corresponde a una presión de 48 kg/m2.
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Long Span Suspension Structure
Date: 24/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TS2 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 700 m Conductor per phase: 1
Weight Span: 1050 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - 1,000 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Suspension and Small Angle Structure
Date: 24/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TSA Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 10 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1050 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - 1,000 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure
Date: 24/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TMS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure
Date: 06/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TMS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -900 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure
Date: 24/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TDS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 65 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
345.6
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure
Date: 24/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TDS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 0 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 65 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -900 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
TORRES DE CIRCUITO DOBLE NORMALES
STRUCTURE LOADS: Lattice Normal Span Suspension Structure
Date: 27/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TD1 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - 1,000 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Long Span Suspension Structure
Date: 27/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TD2 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 700 m Conductor per phase: 1
Weight Span: 1050 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - 1,000 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Suspension and Small Angle Structure
Date: 27/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TDA Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 10 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1050 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - 1,000 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure
Date: 27/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure
Date: 06/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -900 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure
Date: 27/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TDD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 65 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure
Date: 27/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TDD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 0 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 65 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -900 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
TORRES DE BASE ESTRECHA
STRUCTURE LOADS: Lattice Normal Span Suspension Structure Base Estrecha
Date: 26/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TES1 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure Base Estrecha
Date: 26/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TEMS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Normal Span Suspension Structure Base Estrecha
Date: 26/02/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TED1 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure Base Estrecha
Date: 26/02/2004
Client: EPR OFS: D
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: TEMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
ESTRUCTURAS ESTÉTICAS DE POSTES DE ACERO
STRUCTURE LOADS: Steel Pole Normal Span Suspension Structure (Aesthetics)
Date: 26/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PS1 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m
2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
- - - - -
STRUCTURE LOADS: Steel Pole Medium Angle Deadend Structure (Aesthetics)
Date: 26/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PMS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Steel Pole Medium Angle Deadend Structure (Aesthetics)
Date: 26/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PMS Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -900 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Steel Pole Normal Span Suspension Structure (Aesthetics)
Date: 26/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PD1 Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
- - - - -
STRUCTURE LOADS: Steel Pole Medium Angle Deadend Structure (Aesthetics)
Date: 26/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 1500 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Steel Pole Medium Angle Deadend Structure (Aesthetics)
Date: 26/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -900 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
ANEXO 28A
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 2 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 110 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 2,091 1,000 110 10 - -
5 Longitudinal Unbalance 1.20 1.20 1.20 1.20 400 200 110 10
6 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
7 Heavy Vertical 1.70 1.70 1.70 1.70 - 1,000 360 250 - -
- - - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure 4Ckt
Date: 12/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: 2TMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Medium Angle Deadend Structure 4Ckt
Date: 12/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: 2TMD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 30 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -400 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 200 120 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 200 120 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 2,091 1,000 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,000 580 250 - -
- 1,000 - - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure 4Ckt
Date: 12/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: 2TDD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 65 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure 4Ckt
Date: 12/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: 2TDD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 65 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: -400 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
STRUCTURE LOADS: Lattice Terminal and Large Angle Deadend Structure 4Ckt
Date: 12/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: 2TDD Approved By:
Conductor: 1024.5 KCMIL 18/19 ACAR Diameter: 29.59 mm Weight: 1.4312 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAGTEN2 Ver. 2.20a
Line Angle: 0 Deg. Ruling Span: 300 m
Wind Span: 400 m Conductor per phase: 1
Weight Span: 600 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 3,118 1,490 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,425 1,120 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,631 1,234 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,464 700 982 600
8 Heavy Vertical EDS 1.70 1.00 1.70 1.70 - - 580 250 - -
ANEXO 29A
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 5 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: 350 m OHGW/Attachment: 1
Insulator String: V-BRACE Length: 2.60 m Susp Hdw: 20 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 100 100 20 10 76.80 24.00
4 Stringing 1.50 1.50 1.50 1.50 88 770 294 635 - -
5 Heavy Vertical 1.50 1.50 1.50 1.50 - - 360 250 - -
PCAS1-S2 1/2
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 230 kV Suspension and Angle 5-15o
Date: 25/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCASA Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm 2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 15 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: 350 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Susp Hdw: 20 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
1 Transverse High Wind 1,060 2,800 300 330 1,010 150 230 72 All wires intact
2 Longitudinal High Wind 1,060 1,800 360 330 720 150 230 72 All wires intact
3 High Wind 45 degree 1,060 2,290 300 330 850 150 230 72 All wires intact
4 Long. Load Containment 850 1,110 2,120 270 350 1,320 - - Anyone Phase or S Wire
5 Stringing 2,640 1,570 4,190 1,440 490 1,310 - - Anyone Phase or S Wire
6 Heavy Vertical 2,940 1,570 - 1,140 490 - - - Anyone Phase or S Wire
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m 2 kg/m 2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 100 100 20 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 880 1,100 20 10 - -
5 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
PCASA 1/2
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 69 kV Suspension and Angle 5-15o
Date: 25/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCASA Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm 2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 15 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 1
Weight Span: 350 m OHGW/Attachment: 1
Insulator String: 6 ANSI Class 52-5 Length: 1.00 m Susp Hdw: 20 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m 2 kg/m 2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 100 100 20 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 1,760 1,100 20 10 - -
5 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
PCASA 2/2
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 230 kV Dead End and Angle 0-30
Date: 25/03/2004
Client: EPR OFS: Rev A
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCAMS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 30 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: 450 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OPGW Cond. OPGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 400 100 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 400 100 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 1,760 1,100 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,232 770 1,317 635 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 580 250 - -
PCAMS 1/1
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 69 kV Dead End and Angle 0-30
Date: 25/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCAMS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 30 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 1
Weight Span: 450 m OHGW/Attachment: 1
Insulator String: 6 ANSI Class 52-5 Length: 1.00 m Weight: 40 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OPGW Cond. OPGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 40 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 400 100 40 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 400 100 40 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 1,760 1,100 40 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 2,091 1,100 580 250 - -
PCAMS 1/1
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 230 kV Dead End and Angle 0-30
Date: 25/03/2004
Client: EPR OFS: Rev A
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCAMS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 30 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: -300 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 30 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OPGW Cond. OPGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 30 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 400 100 30 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 400 100 30 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 1,760 1,100 30 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,232 770 1,317 635 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 580 250 - -
PCAMS-Uplift 1/1
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 69 kV Dead End and Angle 0-30
Date: 25/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCAMS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 30 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 1
Weight Span: -300 m OHGW/Attachment: 1
Insulator String: 6 ANSI Class 52-5 Length: 1.00 m Weight: 40 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OPGW Cond. OPGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 40 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 400 100 40 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 400 100 40 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 1,760 1,100 40 20 - -
5 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 580 250 - -
PCAMS-Uplift 1/1
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 230 kV Terminal and Angle 0-50
Date: 25/03/2004
Client: EPR OFS: Rev A
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCADS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 50 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: 450 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 2,500 1,933 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,286 1,815 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,346 1,848 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,232 770 1,317 635
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCADS-50 1/2
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 69 kV Terminal and Angle 0-50
Date: 25/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCADS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
2
Overh'd Ground Wire: 107.17 mm OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 50 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 1
Weight Span: 450 m OHGW/Attachment: 1
Insulator String: 6 ANSI Class 52-5 Length: 1.00 m Weight: 40 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 40 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 40 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 40 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 2,500 1,933 40 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,286 1,815 40 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,346 1,848 40 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCADS-50 2/2
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 230 kV Terminal and Angle 0-50
Date: 25/03/2004
Client: EPR OFS: Rev A
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCADS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 50 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: -300 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 2,500 1,933 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,286 1,815 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,346 1,848 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,232 770 1,317 635
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCADS-50-Uplift 1/2
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 69 kV Terminal and Angle 0-50
Date: 25/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCADS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 50 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 1
Weight Span: -300 m OHGW/Attachment: 1
Insulator String: 6 ANSI Class 52-5 Length: 1.00 m Weight: 40 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 40 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 40 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 40 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 2,500 1,933 40 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,286 1,815 40 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,346 1,848 40 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCADS-50-Uplift 2/2
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 230 kV Terminal and Angle 0-50
Date: 28/05/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCADS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 0 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 2
Weight Span: 450 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 2,500 1,933 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,286 1,815 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,346 1,848 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,232 770 1,317 635
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCADS-0 1/2
o
STRUCTURE LOADS: Steel Poles Compact Design Single Ckt 69 kV Terminal and Angle 0-50
Date: 28/05/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCADS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 0 Deg. Ruling Span: 150 m
Wind Span: 250 m Conductor per phase: 1
Weight Span: 450 m OHGW/Attachment: 1
Insulator String: 6 ANSI Class 52-5 Length: 1.00 m Weight: 40 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 500 250 40 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 400 200 40 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 400 200 40 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 2,500 1,933 40 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 2,286 1,815 40 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 2,346 1,848 40 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 1,232 770 866 635
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCADS-0 2/2
ANEXO 30A
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 5 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: 250 m OHGW/Attachment: 1
Insulator String: V-BRACE Length: 2.60 m Susp Hdw: 20 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 100 100 20 10 76.80 24.00
4 Stringing 1.50 1.50 1.50 1.50 125 295 313 397 - -
5 Heavy Vertical 1.50 1.50 1.50 1.50 - - 360 250 - -
PCCS1-S2
STRUCTURE LOADS: Concrete Poles Compact Design Single Ckt 230 kV Suspension and Angle 5-10o
Date: 24/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCCSA Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm 2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 10 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: 250 m OHGW/Attachment: 1
Insulator String: Running Corner Length: 2.60 m Susp Hdw: 20 kg Diameter: 0.254 m
G Wire Hwre Weight: 10 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m 2 kg/m 2
1 Transverse High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 100 100 20 10 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 100 100 20 10 76.80 24.00
4 Long. Load Containment 1.20 1.20 1.20 1.20 658 421 20 10 - -
5 Stringing 1.70 1.70 1.70 1.70 461 295 480 397 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 360 250 - -
PCCSA
STRUCTURE LOADS: Concrete Poles Compact Design Dead End and Medium AngleSingle Ckt 230 kV
Date: 24/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCCMS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 30 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: 250 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OPGW Cond. OPGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 400 100 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 400 100 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 658 421 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 461 295 480 397 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 580 250 - -
PCCMS
STRUCTURE LOADS: Concrete Poles Compact Design Dead End and Medium AngleSingle Ckt 230 kV
Date: 24/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCCMS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 30 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: -150 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OPGW Cond. OPGW Flat Round
Conditions Wind Tension kg/wire kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Transverse High Wind 1.50 1.50 1.50 1.50 500 250 110 20 76.80 48.00
2 Longitudinal High Wind 1.50 1.50 1.50 1.50 400 100 110 20 76.80 48.00
3 High Wind 45 degree 1.50 1.50 1.50 1.50 400 100 110 20 76.80 24.00
4 Temporary deadend EDS 1.20 1.20 1.20 1.20 658 421 110 20 - -
5 Stringing 1.70 1.70 1.70 1.70 461 295 480 397 - -
6 Heavy Vertical 1.70 1.70 1.70 1.70 - - 580 250 - -
PCCMS-Uplift
STRUCTURE LOADS: Concrete Poles Compact Design Terminal and Large Angle Single Ckt 230 kV
Date: 24/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCCDS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 50 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: 250 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 200 100 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 100 100 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 100 100 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 1,000 700 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 747 521 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 823 576 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 461 295 480 397
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCCDS-50
STRUCTURE LOADS: Concrete Poles Compact Design Terminal and Large Angle Single Ckt 230 kV
Date: 24/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCCDS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 50 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: -150 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 200 100 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 100 100 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 100 100 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 1,000 700 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 747 521 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 823 576 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 461 295 480 397
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCCDS-50-Uplift
STRUCTURE LOADS: Concrete Poles Compact Design Terminal and Large Angle Single Ckt 230 kV
Date: 24/03/2004
Client: EPR OFS:
Project: SIEPAC 230 kV Interconnection By: AB
Reviewed By:
Structure Type: PCCDS Approved By:
Conductor: 477.0 KCMIL 26/7 ACSR Diameter: 21.793 mm Weight: 0.976 kg/m
Overh'd Ground Wire: 107.17 mm2 OPGW Diameter: 14.00 mm Weight: 0.593 kg/m
Cable Tens. Source: Sag & Tension Calcs 02/13/2004--SAG10
Line Angle: 0 Deg. Ruling Span: 100 m
Wind Span: 175 m Conductor per phase: 2
Weight Span: -150 m OHGW/Attachment: 1
Insulator String: 16 ANSI Class 52-5 Length: 2.60 m Weight: 110 kg Diameter: 0.254 m
G Wire Hwre Weight: 20 kg
Overload Capacity Factors Long. Cable Tens. Add'l Weight Wind on Structure
Loading Vertical Transv. Long. Cond. OHGW Cond. OHGW Flat Round
Conditions Wind Tension kg/phase kg/wire kg/phase kg/wire kg/m2 kg/m2
1 Angle Trans High Wind 1.50 1.50 1.50 1.50 200 100 110 20 76.80 48.00
2 Angle Long High Wind 1.50 1.50 1.50 1.50 100 100 110 20 76.80 48.00
3 Angle 45 deg High Wind 1.50 1.50 1.50 1.50 100 100 110 20 38.40 24.00
4 Term Trans High Wind 1.50 1.50 1.50 1.50 1,000 700 110 20 76.80 48.00
5 Term Long High Wind 1.50 1.50 1.50 1.50 747 521 110 20 76.80 48.00
6 Term 45 deg High Wind 1.50 1.50 1.50 1.50 823 576 110 20 38.40 24.00
7 Stringing 1.70 1.70 1.70 1.70 461 295 480 397
8 Heavy Vertical EDS 1.70 1.70 1.70 1.70 - - 580 250 - -
PCCDS-0