Documentos de Académico
Documentos de Profesional
Documentos de Cultura
325
235
315
235
215
80 e d 100
510-680
420-570
360-510
e3
490-630
400-560
340-470
3 d e d 100
470-630
390-530
340-470
100 e d 150
Resistencia
a la traccin
R*
(MPa)
22
22
26
e d 40
0,26
0,24
F-26
F-36
0,24
0,27
0,21
16 e d 40
(2)
0,28
0,23
40 e d 100
S mx.
(%)
0,045
0,045
0,045
20
20
24
63 e d 100
0,050
0,050
0,050
P mx.
(%)
21
21
25
40 e d 63
A
(%)
(3) Para espesores ! 100 mm, el contenido de carbono debe acordarse entre las partes.
18
18
22
100 e d 150
(1) El contenido de carbono mximo puede incrementarse hasta en 0,02% siempre y cuando se cumpla con el valor del carbono equivalente mximo indicado en 5.6.1 a).
0,20
e d 16
C mx.
(1) (3)
(%)
295
215
195
100 e d 150
F-24
Designacin
345
235
215
63 e d 80
355
F-36
245
215
40 e d 63
*
**
250
F-26
225
16 e d 40
Re
(MPa)
235
e d 16
F-24
Designacin
del acero
2,5 e
1,5 e
e d 16
1,5 e
16 e d 40
2,5 e
1,5 e
40 e d 63
Doblado** a 180
sobre calza de
IRAM-IAS U 500-503:2003
A 36/A 36M 05
TABLE 3 Tensile RequirementsA
Plates, Shapes,B and Bars:
Tensile strength, ksi [MPa]
Yield point, min, ksi [MPa]
Plates and BarsD,E:
Elongation in 8 in. [200 mm], min, %
Elongation in 2 in. [50 mm], min, %
Shapes:
Elongation in 8 in. [200 mm], min, %
Elongation in 2 in. [50 mm], min, %
5880 [400550]
36 [250]C
20
23
20
21B
A
See the Orientation subsection inthe Tension Tests section of Specification
A 6/A 6M.
B
For wide flange shapes with flange thickness over 3 in. [75 mm], the 80 ksi [550
MPa] maximum tensile strength does not apply and a minimum elongation in 2 in.
[50 mm] of 19 % applies.
C
Yield point 32 ksi [220 MPa] for plates over 8 in. [200 mm] in thickness.
D
Elongation not required to be determined for floor plate.
E
For plates wider than 24 in. [600 mm], the elongation requirement is reduced
two percentage points. See the Elongation Requirement Adjustments subsection
under the Tension Tests section of Specification A 6/A 6M.
SUPPLEMENTARY REQUIREMENTS
These requirements shall not apply unless specified in the order.
Standardized supplementary requirements for use at the option of the purchaser are listed in
Specification A 6/A 6M. Those that are considered suitable for use with this specification are listed by
title:
S5. Charpy V-Notch Impact Test.
SUMMARY OF CHANGES
Committee A01 has identified the location of the following changes to this standard since A 36/A 36M-03a that
may impact the use of this standard. (Approved March 1, 2005.)
(1) Paragraph 6.1 was revised.
Committee A01 has identified the location of the following changes to this standard since A 36/A 36M-03a that may impact
the use of this standard. (Approved April 1, 2004.)
(1) Table 2 has been revised to make Footnote B also apply
to bars.
3
Copyright by ASTM Int'l (all rights reserved); Wed Mar 21 14:37:21 EST 2007
Downloaded/printed by
HILARIO GARCIA (INDUSTRIAS MONTERREY SA DE CV) pursuant to License Agreement. No further reproductions authorized.