Documentos de Académico
Documentos de Profesional
Documentos de Cultura
MOTOR Y VARIADOR
P0317 = 1 (Start-up Orientado = Si) 0
P0202 = 0 (Tipo de Control = V/f 60Hz) 0
P0296 = X (Tensión Nominal Red/ VER MANUAL DE PROGRAMACION) 0 -> 200 - 240V
P0398 = XX (Factor Servicio del Motor / Seleccionar de acuerdo al dato de placa del motor) 1.15
P0400 = 220V (Tensión Nominal Motor / Seleccionar de acuerdo al dato de placa del motor) 220
P0401 = XX (Corriente Nominal Motor/ Seleccionar de acuerdo al dato de placa del motor) 56
P0402 = XX(RPM del Motor / Seleccionar de acuerdo al dato de placa del motor) 3550
P0403 = 60 Hz (Frecuencia Nominal Motor = 60 Hz) 60
P0404 = XX (Potencia Nominal Motor VER MANUAL DE PROGRAMACIÓN) 17-> 20hp
P0406 = 0 (Ventilación del Motor = 0 Autoventilado / 1 = Independiente) 0
P0407 = 0.8 (Factor de potencia del motor / Seleccionar de acuerdo al dato de placa del motor) 0.8
P0408 = 0 (Autoajuste = 0 No) 0
P0409 = XXX (Resistencia Estator / Conforme modelo del convertidor)
PARÁMETROS DE COMUNICACIÓN
P0308 = 1 (Dirección Serial) 1
P0310 = 1 (Tasa Comunicación. Serial / 1 = 19200 bits/s) 1
P0311 = 0 (Configuración Bytes Serial / 0 = 8 bits. sin. 1) 1
P0312 = 2 (Protocolo Serial (1) (2) / 2 = Modbus RTU (1)) 2
PUMP GENIUS
LOCAL/REMOTE
P0220 Local/Remote selection 11 SoftPLC
P0221 Speed reference at Local 0 HMI
P0222 Speed reference at remote 12 SoftPLC
P0223 Forward/reverse key at Local 2 Fwd
P0224 Run/Stop at Local 0 Keys
P0225 JOG at Local 0 Disabled
P0226 Forward/reverse key at Remote 2 Fwd
P0227 Run/Stop at Remote 5 SoftPLC
P0228 JOG at Remote 0 Disabled
INPUT /OUTPUTS
P0263 DI1 Function 44 Enable Pump Genius
P0264 DI2 Function 39 Enable Pump 1 (DO1)
P0265 DI3 Function 41 Enable Pump 2(DO2)
P0266 DI$ Function 0 Not used
P0267 DI5 Function 0 Not used
P0268 DI6 Function 0 Not used
P0269 DI7 Function 0 Not used
P0270 DI8 Function 0 Not used
P0271 Digital input signal 0 All Dix are NPN
P0275 DO1 Function 37 Start Pump 1
P0276 DO2 Function 0 Not used
P0277 DO3 Function 38 Start Pump 2
P0278 DO4 Function 13 No Fault
P0279 DO5 Function 0 Not used
PROCESS
P0100 Acceleration time 10 s
P0101 Deceleration time 10 s
P0134 Maximum speed 60 Hz
P0133 Minimum speed 30 Hz
ANALOG INPUT
P0231 AI1 Signal Function 8 Process Variable
P0233 AI1 Signal Type 1 4 to 20 mA
P0510 Engineering Unit 1 0 None
P0511 Decimal Point og Engineering unit 1 xyw.z
ANALOG INPUT
P0234 AI1 Offset 0%
P0235 AI1 Filter 0.25 %
P0323 AI1 Gain 1
P0018 AI1 Value Read %
ANALOG INPUT
P1023 Maximum Level 165 eng 1
PID
P1030 Control action of PID 1 Direct mode (SP-PV)
P1031 Proporcional Gain P 0.8
P1032 Integral Gain I 20
P1033 Derivative Gain D 17
P1016 Process Value read
P1011 Control setpoint read
SP
P1020 Control Setpoint Source P1011 4 SP via HMI
SLEEP / WAKE UP
P0002 Motor Speed read
P1037 Motor speed to sleep 48 hz
P1038 Time delay to sleep 5s
P1034 Deviation to wake up 1 eng 1
P1036 Time delay to wakeup 1s
FORCING ROTATION
P1018 Time for rotation 72 h
P1019 Speed for rotation 0 Hz
PIPE BREAKING
P1024 Low level limit 30 eng 1
A770 Alarma pipe breaking
P1025 Time delay for fault 3s
F771 Low level FAULT Stop system
PIPE OBSTRUCTION
P1026 High level limit 95 eng 1
A772 Alarm pipe obstruction
P1027 Time dealy for fault 3s
F773 High level Fault
HMI MONITORING
P0206 Secondary display P0002
P0205 Main display P1016
P0207 Bar graph display P0003
FALLA EXTERNA
F0070 FALLA SOBRE CORRIENTE /CORTOCIRCUITO
Short-circuit between two motor phases.
Short-circuit of the rheostatic braking resistor connecting cables.
IGBTs module in short-circuit or damaged.
Start with too short acceleration ramp.
Start with motor spinning without the Flying Start function.
00-00 Code of drive
00-02 Reset 0
00-03 Start-up display Freq command 0
00-04 User display Dcbus 3
00-10 Control mode Speed mode 0
00-11 Speed mode control V/F 0
00-16 Load selection Normal 0 1 Heavy
00-20 Source of master freq comm(AUTO) Digital Key pad 0
00-21 Source of operation comm(AUTO) External terminals 1
00-22 Stop method Ramp to stop 0 1 Coast stop
00-23 Motor direction reverse disable 1 0 en fwr /rev
Basic parameters
01-00 Max freq 60Hz
01-01 Output freq m1 60Hz
01-09 Start up freq 0,5Hz
01-10 Output freq upper limit 60Hz
01-11 Output freq lower limit 0Hz
01-12 Accel time 40 seg
01-13 Decel time 40 seg
01-43 V/f curve selection 0
01-45 Time unit for accel/decel 0.01 0 1 0,1 Punto decimal
Group 02 Digital Input/output parameters
02-00 2-wire/3-wire opreation control 0
02-01 Input command 1 MI1 Reset 5
02-13 Output function RY1 Malfunction 11
02-14 Output function RY2 Operation indication 1
Group 05 Motor parameters
05-01 Motor auto tunning No function 0
05-01 FLA m1 10 - 120% drive´s rated current xxxA
05-02 Rated power m1 xxx kW
05-03 Rated speed xxxx rpm
05-04 Pole Number x
05-05 No load current of m1 xxA
05-33 Induction or permanent motor Induction 0 1 Permanent
Group 06 Protection Parameters
06-00 Low voltage level 230V: 150-220V frame A to D 180
230V: 190-220V frame E and above
460V: 300 - 440V frame A to D 360
460V: 380 - 440V frame E and above 400
06-01 Over Voltage Stall prevention 0: disabled
230V: 0,0 - 450,0 VDC 380
460V: 0,0 - 900,0VDC 760
06-02 Selection for Over Voltage Stall prevention 0: Traditional 0
1: Smart
Over-current stall prevention during Normal Load : 0 - 160% (100% drive´s rated
06-03 acceleration current) 120
Heavy Load: 0 - 180% (100% drive´s rated
current) 150
Over-current stall prevention during Normal Load : 0 - 160% (100% drive´s rated
06-04 operation current) 120
Heavy Load: 0 - 180% (100% drive´s rated
current) 150
Accel./Decel. Time selection of Stall
06-05 prevention at Constant Speed 0: by current Accel /Decel time 0
06-06 Over-torque detection Selection (OT1) 0. No function 0
06-07 Over-torque detection level (OT1) 10 - 250% (100% drive´s rated current) 120
06-08 Over-torque detection time (OT1) 0,0 - 60,0 seg 0.1
06-12 Current Limit 0 - 250% (100% drive´s rated current) 170
06-13 Electronic Thermal Relay Selection M1 2: Disable 2 1 Standard motor
06-14 Electronic Thermal Characteristics M1 30,0 - -600,0 s 60s
06-15 Heat sink Over-heat (OH) Warning 0,0 - 110 °C 105
06-16 Stall prevention Limit level 0 - 100% (Pr 06-03, Pr06-04) 50
06-17 Present Fault record 0