Documentos de Académico
Documentos de Profesional
Documentos de Cultura
FF
FF
Goulds Pumps
3656/3756 M & L-Group
Cast Iron, Bronze Fitted, End-Suction Flanged Pumps
Bombas horizontales con brida en hierro fundido
o hierro fundido y bronce
www.goulds.com
GOULDS PUMPS 2
Commercial Water
Performance Coverage
Campo de desempeño
FEET
PIES
500
3500 RPM
400
21/2 x 3 — 10
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
300
11/2 x 2 — 10
2 1 /2 x 3 — 8
200
21/2 x 3 — 9
3x4—8 3 x 4 — 10
4x5—8
100
0
0 200 400 600 800 1000 1200 1400 1600 1800
GALLONS PER MINUTE (GALONES POR MINUTO) U.S. GPM
FEET
PIES
300
1750 RPM
4 x 6 — 16
250
200
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
150
21/2 x 3 — 13
6 x 8 — 13
100 2 1/2
x3 3 x 4 — 13
— 4 x 6 — 13 8 x 10 — 13
10
1 /2 x 2 — 10
1 2 1/
2
x3
—
9
4 x 6 — 10
50
2 1 /2 x 3 — 8
3 x 4 — 10
3x4—8 4x5—8
0
10 100 200 400 1000 1500 2000 3000 4000 5000
GALLONS PER MINUTE (GALONES POR MINUTO) U.S. GPM
GOULDS PUMPS 3
Commercial Water
3656/3756 M & L-Group Numbering System
Sistema de numeración del Grupo M y L, modelos 3656/3756
The various versions of the 3656 and 3756 M & L-Group are identified by Las diferentes versiones de los modelos 3656 y 3756 del Grupo M Y L se identifi-
a product code number on the pump label. This number is also the catalog can con un número de código de producto en la etiqueta de la bomba. Este nú-
number for the pump. The meaning of each digit in the product code num- mero es también el número de catálogo de la bomba. A continuación se ilustra el
ber is shown below. Not all combinations are possible; consult your Goulds significado de cada dígito en el código del producto. No todas las combinaciones
Pumps distributor for specific requirements. son posibles, consulte a su distribuidor Goulds Pumps para requisitos específicos.
Example Product Code, Ejemplo del código de producto
11 BF 2 L 5 A 0
Mechanical Seal/Packed Box and O-ring Material, Materiales del sello mecánico/empaque y anillo en O
For Optional Mechanical Seal modify catalog order no. with Seal code listed below.
Para sellos mecánicos optativos, modificar el número de pedido del catálogo con los códigos de sello que se indican a continuación.
Seal Part No., Pieza Número
Code, Rotary, Stationary, Elastomers, Metal Parts,
M-Group, Grupo-M L-Group,
Código Rotativo Estacionario Elastómeros Partes Metálicas
del Sello 1.25" Shaft 1.625" Shaft Grupo-L
0 Ceramic, Cerámica BUNA-N 10K13 10K16 10K84
Carbon,
1 Carbone EPR 10K19 10K20 NA
3 Sil-Carbide, 316 SS, 10K27 10K45 10K112
5 Carburo de Viton 316 Acero inoxidable 10K64 10K65
8A* Sil-Carbide silicona NA NA 10K144
8B** 10K64 10K65
9*** Packed Box Design with BUNA O-Ring, Diseño de prensaestopas empacado con anillo en O de BUNA 15K17 15K3 15K4
* Prime-Safe option with oiler, Opción Primero-Segura con el engrasador ** Prime-Safe option with grease, Opción Primero-Segura con la grasa
*** All Packed Box Units use JP style motors, Todas las unidades de prensaestopas empacado utizilan motores estilo JP
Impeller Option Code, Código de opción de impulsor
■ Indicates L-Group pump (1780 RPM, 60 to 150 HP) • For 1180 RPM Close-Coupled applications only.
■ Indica una bomba Grupo “L”. (1780 RPM, de 60 a 150 HP) • Para aplicaciones de acople cerrado de 1180 RPM únicamente.
L-Group Pump Size,
M-Group Pump Size, Tamaño de la bomba
Impeller Code Tamaño de la bomba
Código del 8 7 11 13 16 12 14 10 17 15 21 18 19 20
impulsor
Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia. Dia.
A 10 1⁄16" 715⁄16" 101⁄16" 131⁄16" 81⁄16" 101⁄16" 131⁄16" 77⁄8" 101⁄16" 127⁄8" 101⁄16" ■13” ■13” ■16”
B 93⁄16 77⁄16 97⁄8 12¾ 77⁄16 9¾ 129⁄16 7¾ 99⁄16 12½ 97⁄8
■12½ ■12¾ ■155⁄8
C 8 ⁄8
3
7 ⁄16
3
9 ⁄8
5
11 ⁄8
7
7 ⁄16
7
9 12 ⁄16
5
7½ 91⁄8 12¼ 9½
■125⁄16 ■123⁄8 ■153⁄16
D 7¾ 613⁄16 9 113⁄8 6¾ 85⁄8 12 7¼ 811⁄16 117⁄8 9¼
■117⁄8 ■1115⁄16 ■14½
E 7¼ 63⁄8 85⁄8 97⁄8 63⁄8 81⁄8 11¾ 7 81⁄8 113⁄8 815⁄16
115⁄8 ■1111⁄16 ■13¾
F 7 63⁄16 8¼ 93⁄8 515⁄16 75⁄8 115⁄16 6¾ 7¾ 111⁄16 8½
111⁄8 ■11¼
G 8 5½ *91⁄8 10¾ 6½
107⁄8 83⁄16
107⁄8 ■107⁄8
H 75⁄8 51⁄8 *8¾ 101⁄8 61⁄16
10½ 8
10½
■913⁄16
J 71⁄8 45⁄8 *89⁄16 91⁄8 5¾
10¼ 711⁄16
10 •13
K *8 ⁄8 8 ⁄16
1 11
97⁄8
9½ •12¾
L *7¾ 8 93⁄8 •13 •123⁄8
M *75⁄8 79⁄16 131⁄16 •12½ •1115⁄16
N *7¼ •125⁄16 •1111⁄16
P *71⁄16 •117⁄8 •11¼
Q •107⁄8
R *6¾ •913⁄16
Driver, Elemento motor Drive Options, Opciones de mando
1 = 1 PH, ODP 3 = 575 V, ODP 5 = 3 PH, TEFC 7 = 3 PH, XP 9 = 3 PH, TEFC, Substitute, Description,
2 = 3 PH, ODP 4 = 1PH, TEFC 6 = 575 V, TEFC 8 = 575 V, XP Premium efficiency Substituto Descripción
1PH = monofásico, 3PH = trifásico 0 = 1 PH, XP Eficiencia superior
FRM Bearing frame mount,
HP Rating, Potencia nominal, HP Montaje del bastidor del cojinete
G = 2 J = 5 L = 10 N = 20 Q = 30 S = 50 U = 75 W = 125
SAE1 SAE #1 mount, Montura SAE #1
H = 3 K = 7½ M= 15 P = 25 R = 40 T = 60 V = 100 X = 150
SAE2 SAE #2 mount, Montura SAE #2
Driver: Hertz/Pole/RPM, Elemento motor: Hertz/Polos/RPM
1 = 60 Hz, 2 pole, 3500 RPM 3 = 60 Hz, 6 pole, 1180 RPM 5 = 50 Hz, 4 pole, 1450 RPM SAE #3 mount, Montura SAE #3
2 = 60 Hz, 4 pole, 1750 RPM 4 = 50 Hz, 2 pole, 2900 RPM SAE4 SAE #4 mount, Montura SAE #4
Material (Packed Box in AI or BF), Material (Caja prensaestopas en AI o BF) SAE #5 mount, Montura SAE #5
AI = All iron BF = Bronze fitted AI = Todo hierro BF = con accesorios de bronce SAE drive number is determined by the
Pump Size, Tamaño de bomba engine flywheel housing size.
8 = 1½ x 2 – 10 11 = 2½ x 3 – 10 12 = 3 x 4 – 10 10 = 4 x 5 – 8 16 = 3 x 4 – 8 El número del mando SAE se determina por
18 = 6 x 8 – 13 19 = 8 x 10 – 13 20 = 4 x 6 – 16 21 = 2½ x 3 – 9 el tamaño de la caja del volante del motor.
7 = 2½ x 3 – 8 13 = 2½ x 3 – 13 14 = 3 x 4 – 13 15 = 4 x 6 – 13 17 = 4 x 6 – 10 (BF Only) (Accesorios de bronce únicamente)
* Indicates 3500 RPM impeller for the 3 x 4 – 10, all others are 1750 RPM.
* Indica un impulsor de 3500 RPM para el 3 x 4 – 10, todos los demás son de 1750 RPM.
GOULDS PUMPS 4
Commercial Water
Performance Curves – 60 Hz, 3500 RPM
Curvas de desempeño – 60 Hz, 3500 RPM
These curves show the performance of the 3656 and 3756 at 3500 RPM and Estas curvas ilustran el desempeño de los modelos 3656 y 3756 operando a
1750 RPM, 60 Hz, and at 2900 RPM and 1450 RPM, 50 Hz. Standard impeller 3500 RPM y 1750 RPM en 60 Hz, y a 2900 RPM y 1450 RPM en 50 Hz. Se
trims are shown. Note that not all pump sizes are available at the higher speeds. muestran los diámetros de impulsor estándar. Se ha de notar que no todos los
tamaños de bomba están disponibles en altas velocidades.
Model 8AI/BF / Size (Tama o) 11/2 x 2 — 10 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
RPM 3550 Curve (Curva) CN0207R01 NOTA: No se recomienda para funcionamiento superior Impulsor optativo
METERS FEET
METROS IMP. DWG. No. 114-51 al impreso en la curva H-Q.
PIES Ordering Code Dia.
160
Código de pedido Diá.
500 A 101/16" DIA. 50 % EFF A 101⁄16"
8’ 54 12’ NPSHR — FEET (PIES)
10’ B 93⁄16"
140
58 14’ 16’ C 83⁄8
400
B 93/16" 60 D 7¾
120 58
E 7¼
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
54
C 83/8" F 7
100
300 D 73/4" NOTE: Pump will pass a
sphere to 5⁄32" diameter.
40 HP
80 E 71/4" NOTA: La bomba dejará pasar
F 7"
30 HP una esfera de hasta 5⁄32 de
200
pulgada de diámetro.
60
25 HP
20 HP
40
15 HP
100
20
0 0
0 50 100 150 200 250 U.S. GPM 300
0 10 20 30 40 50 60 m hr
3
CAPACITY (CAPACIDAD)
Model 7AI/BF / Size (Tama o) 21/2 x 3 — 8 NOTE: Not recommended for operation beyond printed H-Q curve. Optional Impeller
RPM 3500 Curve (Curva) CN208R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
en la curva H-Q.
IMP. DWG. No. 114-50 Ordering Code Dia.
Código de pedido Diá.
METERS FEET 6’ NPSHR — FEET (PIES) 8’ A 715⁄16"
METROS PIES 7’
73 B 77⁄16
300 40% EFF 50 60 10’
65 70
A 715/16" DIA. 75 12’ C 73⁄16
80 78
D 613⁄16
15’ 18’ E 63⁄8
250 B 77/16"
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
78
75
73 F 63⁄16
C 73/16"
NOTE: Pump will pass a
60 200 D 6 /16"
13
50
0 0
0 50 100 150 200 250 300 350 400 U.S. GPM
0 20 40 60 80 100 m3 hr
CAPACITY (CAPACIDAD)
GOULDS PUMPS 5
Commercial Water
Performance Curves – 60 Hz, 3500 RPM
Curvas de desempeño – 60 Hz, 3500 RPM
Model 21BF / Size (Tama o) 21 2 x 3 — 9 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve. Impulsor optativo
RPM 3550 Curve (Curva) CN0672R00 NOTA: No se recomienda para funcionamiento
METERS FEET
METROS PIES IMP. DWG. No. 279-15 superior al impreso en la curva H-Q. Ordering Code Dia.
450 Código de pedido Diá.
90 A 101 16" DIA.
B 97 8" 60 % EFF A 101⁄16"
400 8’ NPSHR — FEET (PIES) B 97⁄8
80 C 91 2" 65 10’
D 91 4" 14’ C 9½
68
70 350 16’ D 9¼
E8 15
16 "
70 24’ E 815⁄16
20’
F 81 2"
300 F 8½
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
60 65
G8 3
16 "
H 8" 60
G 83⁄16
50 250 J 711 16" 56
H 8
J 711⁄16
40 200
NOTE: Pump will pass a
sphere to 5⁄16" diameter.
60 HP
30 150
50 HP
NOTA: La bomba dejará pasar
una esfera de hasta 5⁄16 de
20 HP 40 HP pulgada de diámetro.
20 100
30 HP
25 HP
10 50
0 0
0 100 200 300 400 500 600 700 U.S. GPM 800
Model 11AI/BF / Size (Tama o) 21 2 x 3 — 10 NOTE: Not recommended for operation beyond
Optional Impeller
printed H-Q curve.
RPM 3550 Curve (Curva) CN0085R01 NOTA: No se recomienda para funcionamiento superior Impulsor optativo
IMP. DWG. No. 121-37 al impreso en la curva H-Q.
METERS FEET Ordering Code Dia.
METROS PIES Código de pedido Diá.
10’ NPSHR — FEET (PIES)
A 101⁄16"
12’ 14’ 16’
150 64 % EFF
B 97⁄8
500 72 18’
A 101 16" DIA. 70
B 97 8"
74 20’ C 95⁄8
76 22’ D 9
C 95 8"
125 76 E 85⁄8
400 D 9" 74
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
72 F 8¼
E 85 8"
100
G 8
F 81 4"
300 G 8" 75 HP
H 75⁄8
H 75 8" J 71⁄8
75 J 71 8" 60 HP NOTE: Pump will pass a
200 50 HP
sphere to 5⁄16" diameter.
50 40 HP NOTA: La bomba dejará pasar
una esfera de hasta 5⁄16 de
30 HP
pulgada de diámetro.
100
25
0 0
0 100 200 300 400 500 600 700 U.S. GPM 800
GOULDS PUMPS 6
Commercial Water
Performance Curves – 60 Hz, 3500 RPM
Curvas de desempeño – 60 Hz, 3500 RPM
Model 16AI/BF / Size (Tama o) 3 x 4 — 8 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
RPM 3500 Curve (Curva) CN374R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
METERS FEET
METROS PIES IMP. DWG. No. 277-09 en la curva H-Q. Ordering Code Dia.
90 300 45% EFF 58 68 11’ 13’
Código de pedido Diá.
73
A 81 " DIA.
16
76 A 81⁄16"
80 B 77⁄16
250 D 6¾
16’ 21’ NPSHR — FEET (PIES)
76
70 B 77 16 " E 63⁄8
73
27’
F 515⁄16
200
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
60 68 G 5½
D 63 4"
H 51⁄8
E 63 8" 58
50 J 45⁄8
150
F5 15
16 " NOTE: Pump will pass a
40 sphere to 3⁄8" diameter.
G 51 2"
NOTA: La bomba dejará pasar
50
H 51 8"
100 una esfera de hasta 3⁄8 de
HP
30
40
pulgada de diámetro.
HP
J 45 8" 30
20 HP
25
50 20 HP
HP
10 15
10 HP
71 HP
2
HP
0 0
0 100 200 300 400 500 600 700 800 U.S. GPM 900
Model 3656/3756 M-Group 3500 RPM NOTE: Not recommended for operation beyond
printed H-Q curve.
Optional Impeller
METERS FEET 12BF / Size (Tama o) 3 x 4 — 10 NOTA: No se recomienda la operaci n m s all
Impulsor optativo
METROS PIES Imp. Dwg. 118-81 de la curva impresa de H-Q (carga-capacidad). Ordering Code Dia.
400
Código de pedido Diá.
60% EFF. 70
10' NPSHR – FEET (PIES)
74 76
11' G 91⁄8"
350 G 9 ⁄8 DIA.
1
78
80 13'
H 8¾
100 H 83⁄4
15' J 89⁄16
300 J 8 ⁄16
9
80 K 81⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
K 81⁄8 78
76 18'
74 L 7¾
250 L 7 ⁄54
3
M 7 ⁄8
70 20' M 75⁄8
N 71⁄4 N 7¼
200 P 71⁄16 60
P 71⁄16
R 63⁄4
50 R 6¾
150
NOTE: Pump will pass a
75 HP sphere to ½" diameter.
100
60 HP NOTA: La bomba dejará pasar
50 HP una esfera de hasta ½ de
40 HP
50 pulgada de diámetro.
30 HP
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200U.S. GPM
0 50 100 150 200 250 300 350 m3 hr
CAPACITY (CAPACIDAD)
GOULDS PUMPS 7
Commercial Water
Performance Curves – 60 Hz, 3500 RPM
Curvas de desempeño – 60 Hz, 3500 RPM
Model 10AI/BF / Size (Tama o) 4 x 5 — 8 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
RPM 3500 Curve (Curva) CN0078R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
METERS FEET IMP. DWG. No. 120-08 en la curva H-Q.
METROS PIES Ordering Code Dia.
Código de pedido Diá.
% EFF NPSHR — FEET (PIES)
275 50 60 20’ A 77⁄8"
80 70 75
A 77 8" DIA. 78 80 B 7¾
250 B 73 4" 82
C 71 2"
22’ C 7½
70
225 24’ D 7¼
D 71 4"
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
200
E 7
60
E 7" 80 26’ F 6¾
175 F 63 4" 78
30’ G 6½
50 75
G 61 2"
150 70
H 61⁄16
40
H 61 16 " J 5¾
125
J 53 4" 60 NOTE: Pump will pass a
30 100 sphere to 5⁄16" diameter.
75
HP NOTA: La bomba dejará pasar
75 60 una esfera de hasta 5⁄16 de
20 50 HP
HP pulgada de diámetro.
50 40
HP
10
25 30
HP
0 0
0 200 400 600 800 1000 1200 1400 1600 U.S. GPM
Model 8AI/BF / Size (Tama o) 11 2 x 2 — 10 NOTE: Not recommended for operation beyond printed H-Q curve. Optional Impeller
NOTA: No se recomienda para funcionamiento superior al impreso en la curva H-Q.
METERS FEET RPM 1750 Curve (Curva) Impulsor optativo
METROS PIES IMP. DWG. No. 120-03
120 Ordering Code Dia.
5’ NPSHR — FEET (PIES)
35 30% EFF
35
Código de pedido Diá.
40
110 A 101 16" DIA. 42
45
A 101⁄16"
47 6’
48 B 93⁄16
30 100
C 83⁄8
B 93 16 "
D 7¾
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
90 48
7’
47
25 45
F 7
80
C 83 8" 42
NOTE: Pump will pass a
70 40 sphere to 5⁄32" diameter.
D7 3
"
20 4
NOTA: La bomba dejará pasar
60 una esfera de hasta 5⁄32 de
35
F 7" pulgada de diámetro.
15 50
5
HP
40
10
30
20
2
5
3
HP
HP
10
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 U.S. GPM
0 5 10 15 20 25 30 35 m3 hr
CAPACITY (CAPACIDAD)
GOULDS PUMPS 8
Commercial Water
Performance Curves – 60 Hz, 1750 RPM
Curvas de desempeño – 60 Hz, 1750 RPM
Model 7AI/BF / Size (Tama o) 21 2 x 3 — 8 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
METERS FEET
RPM 1750 Curve (Curva) NOTA: No se recomienda para funcionamiento superior Impulsor optativo
METROS PIES IMP. DWG. No. 120-01 al impreso en la curva H-Q.
70
Ordering Code Dia.
A 715 16" DIA. 50% EFF 55 4’ 60 6’ NPSHR — FEET (PIES) Código de pedido Diá.
64
20 A 7 15⁄16"
65 66 8’
68 B 7 7⁄16
60 B 77 16"
9’
C 73⁄16
66
55 C 73 16" D 613⁄16
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
64 10’
F 6 3⁄16
15 50 D 613 16" NOTE: Pump will pass a
11’
60 sphere to 5⁄16" diameter.
45
NOTA: La bomba dejará pasar
55 una esfera de hasta 5⁄16 de
40 F 63 16" pulgada de diámetro.
50
35
10
30 5 HP
25
3 HP
20
2 HP
5
15
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 U.S. GPM
0 10 20 30 40 50 60 70 m3 hr
CAPACITY (CAPACIDAD)
Model 21BF / Size (Tama o) 21 2 x 3 — 9 NOTE: Not recommended for operation beyond Optional Impeller
RPM 1750 Curve (Curva) CN0674R00 printed H-Q curve. Impulsor optativo
METERS FEET NOTA: No se recomienda para funcionamiento
METROS PIES IMP. DWG. No. 279-15 superior al impreso en la curva H-Q. Ordering Code Dia.
120 Código de pedido Diá.
A 101⁄16"
A 10 16" DIA.
1
64 % EFF 65
B 97⁄8
B 97 8" 4’ NPSHR — FEET (PIES)
100 3’ 66 68 C 9½
30
C 91 2" 70 D 9¼
8’
D 91 4"
5’
E 815⁄16
E8 15
" 70
80
16
68 F 8½
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
F 81 2" 66 G 83⁄16
G 83 " 62
H 8
16
20 H 8"
60 J 7
11
16 " 56 J 711⁄16
NOTE: Pump will pass a
sphere to 5⁄16" diameter.
40 2 HP 71 2 HP NOTA: La bomba dejará pasar
10
una esfera de hasta 5⁄16 de
5 HP pulgada de diámetro.
20
3 HP
0 0
0 50 100 150 200 250 300 350 U.S. GPM 400
0 10 20 30 40 50 60 70 80 90 m3 hr 100
CAPACITY (CAPACIDAD)
GOULDS PUMPS 9
Commercial Water
Performance Curves – 60 Hz, 1750 RPM
Curvas de desempeño – 60 Hz, 1750 RPM
Model 11AI/BF / Size (Tama o) 21 2 x 3 — 10 NOTE: Not recommended for operation beyond
printed H-Q curve. Optional Impeller
METERS FEET RPM 1750 Curve (Curva)
METROS PIES NOTA: No se recomienda para funcionamiento superior Impulsor optativo
IMP. DWG. No. 120-04 al impreso en la curva H-Q.
130 Ordering Code Dia.
35 62 % EFF 6’ NPSHR — FEET (PIES)
Código de pedido Diá.
120 A 101 16" DIA. 65
70
8’
A 10 1⁄16"
110 C 95 8" 72
10’
C 9 5⁄8
30 72
D 9
100
70
D 9" E 85⁄8
25 90
G 8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
E 85 8 "
65
80 J 7 1⁄8
G 8"
20 70 NOTE: Pump will pass a
10 HP sphere to 5⁄16" diameter.
60 J 71 8" 71 2 HP NOTA: La bomba dejará pasar
15 una esfera de hasta 5⁄16 de
50
pulgada de diámetro.
40
5 HP
10
3 HP
30
20
5
10
0 0
0 50 100 150 200 250 300 350 400 U.S. GPM
0 10 20 30 40 50 60 70 80 90 m3 hr
CAPACITY (CAPACIDAD)
Model 13AI/BF / Size (Tama o) 21 2 x 3 — 13 NOTE: Not recommended for operation beyond printed
Optional Impeller
H-Q curve.
RPM 1750 Curve (Curva) CN0104R00 NOTA: No se recomienda para funcionamiento superior al Impulsor optativo
IMP. DWG. No. 276-46 impreso en la curva H-Q.
METERS FEET
Ordering Code Dia.
METROS PIES Código de pedido Diá.
% EFF
8’ NPSHR — FEET (PIES) A 131⁄16"
60 50 B 12¾
200 55
A 131 " DIA. 60
16
63
12’ C 117⁄8
180 B 123 4"
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
65
D 113⁄8
50 16’
160
C 117 8"
E 97⁄8
65
F 93⁄8
140 D 113 8" 20’
40 63 NOTE: Pump will pass a
60 sphere to 5⁄16" diameter.
120
E 97 8" 55 NOTA: La bomba dejará
30 100
F 93 8" 50
pasar una esfera de hasta 5⁄16
de pulgada de diámetro.
80
40
20
60
40
20
10
HP
15
20
10
HP
HP
0 0
0 100 200 300 400 500 600 700 800 U.S. GPM
GOULDS PUMPS 10
Commercial Water
Performance Curves – 60 Hz, 1750 RPM
Curvas de desempeño – 60 Hz, 1750 RPM
Model 16AI/BF / Size (Tama o) 3 x 4 — 8 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
METERS FEET RPM 1750 Curve (Curva) CN375R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
METROS PIES IMP. DWG. No. 277-05 en la curva H-Q.
100 Ordering Code Dia.
30 Código de pedido Diá.
A 8 1⁄16"
C 7 7⁄16
25
80 D 6¾
NPSHR — FEET (PIES) 4’
45% EFF 58
68 73 E 63⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
76 6’
A 81 16" DIA.
F 515⁄16
20
76 8’ G 5½
60 73
C 77 16" 68 H 51⁄8
58
15
J 4 5⁄8
D 6 3 4" NOTE: Pump will pass a
40 E 63 8" sphere to 3⁄8" diameter.
7
1 2
NOTA: La bomba dejará
H
10
P
F 515 16"
pasar una esfera de hasta 3⁄8 de
G 5 1 2"
5 pulgada de diámetro.
H 51 8" HP
20
5 J 45 8"
3
HP
2
HP
1H
P
0 0
0 50 100 150 200 250 300 350 400 U.S. GPM 450
0 10 20 30 40 50 60 70 80 90 m3 hr 100
CAPACITY (CAPACIDAD)
Model 12AI/BF / Size (Tama o) 3 x 4 — 10 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
RPM 1750 Curve (Curva) CN0096R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
IMP. DWG. No. 120-05 en la curva H-Q.
METERS FEET Ordering Code Dia.
METROS PIES NPSHR — FEET (PIES) Código de pedido Diá.
% EFF
6’
A 10 1⁄16"
50 60 8’
70 75 B 9¾
78
110 A 101 16" DIA. 10’
80 12’ C 9
B 93 4"
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
30 100 D 85⁄8
80
90 78
E 81⁄8
C 9" 75
25
15’ F 7 5⁄8
80 D 85 8"
70 NOTE: Pump will pass a
70 E 81 8" sphere to 3⁄8" diameter.
20
60
NOTA: La bomba dejará pasar
60 F 75 8" una esfera de hasta 3⁄8 de
50 pulgada de diámetro.
15 50
40
10
30
15
HP
5
20
H
5
P
10
7
1 2
HP
H
0 10
P
0 100 200 300 400 500 600 700 800 U.S. GPM
GOULDS PUMPS 11
Commercial Water
Performance Curves – 60 Hz, 1750 RPM
Curvas de desempeño – 60 Hz, 1750 RPM
Model 14AI/BF / Size (Tama o) 3 x 4 — 13 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
RPM 1750 Curve (Curva) CN0112R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
IMP. DWG. No. 276-45 Ordering Code Dia.
METERS FEET
METROS PIES Código de pedido Diá.
A 13 1⁄16"
NPSHR — FEET (PIES) 4’
60 200
C 12 5⁄16
5’
60 % EFF 70
6’ E 11¾
75
180 A 131 16" DIA. G 10¾
50 78
160 78
8’
J 91⁄ 8
C 125 16 "
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
75 L 8
140 E 113 4" 10’
40 70 12’ NOTE: Pump will pass a
120 sphere to 3⁄8" diameter.
G 10 3 4
"
60 NOTA: La bomba dejará pasar
30 100 una esfera de hasta 3⁄8 de
50 pulgada de diámetro.
J 91 8"
80
30
20 HP
60 L 8"
25
40 HP
10 20
HP
20 15
71 10 HP
2
HP HP
0 0
0 100 200 300 400 500 600 700 800 U.S. GPM 900
Model 14AI/BF / Size (Tama o) 3 x 4 — 13 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
RPM 1750 Curve (Curva) CN0118R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
IMP. DWG. No. 276-45 en la curva H-Q. Ordering Code Dia.
METERS FEET
METROS PIES Código de pedido Diá.
B 12 9⁄16"
60
D 12
200
4’ NPSHR — FEET (PIES)
F 115⁄16
60% EFF 5’
180 70 H 10 1⁄8
75 6’
50 B 129 " DIA. K 8 11⁄16
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
16
160 78
D 12" 78
8’ M 7 9⁄16
140
40 F 115 16 "
75 10’ NOTE: Pump will pass a
120
70 12’ sphere to 3⁄8" diameter.
NOTA: La bomba dejará pasar
H 101 8" 60
30 100 una esfera de hasta 3⁄8 de
pulgada de diámetro.
50
80
K 811 16 "
20
60 30
M 79 16 "
HP
25
40 HP
10 20
HP
20 71 15
10
2
HP HP HP
0 0
0 100 200 300 400 500 600 700 800 U.S. GPM 900
GOULDS PUMPS 12
Commercial Water
Performance Curves – 60 Hz, 1750 RPM
Curvas de desempeño – 60 Hz, 1750 RPM
Model 10AI/BF / Size (Tama o) 4 x 5 — 8 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
METERS FEET
RPM 1750 Curve (Curva) NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
METROS PIES IMP. DWG. No. 120-02 en la curva H-Q.
70 Ordering Code Dia.
6’ NPSHR — FEET (PIES)
Código de pedido Diá.
50% EFF 60
20 70 8’
65 A 77 8" DIA. 75
78 A 7 7⁄8"
80 82 C 7½
60 C 71 2"
D 7¼
55 D 71 4" F 6¾
10’
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
82
G 6½
80 11’
15 50 J 5¾
78
F 63 4"
45 75
NOTE: Pump will pass a
sphere to 5⁄16" diameter.
12’
70
40 G 1
6 2"
NOTA: La bomba dejará pasar
una esfera de hasta 5⁄16 de
60 pulgada de diámetro.
35
10
J 53 4"
30
25
3
10
HP
7
1 2
HP
HP
20
5
HP
15
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 U.S. GPM
Model 17BF / Size (Tama o) 4 x 6 — 10 1750 RPM NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve. Impulsor optativo
RPM 1750 Curve (Curva) CN0452R00 NOTA: No se recomienda para funcionamiento superior
METERS FEET IMP. DWG. 277-78 al impreso en la curva H-Q. Ordering Code Dia.
METROS PIES Código de pedido Diá.
NPSHR — FEET (PIES)
35 A 101⁄16"
8’
110 60 70 75 B 99⁄16
A
C 91⁄8
30 100 101/16’’ DIA. 80 82
83 D 811⁄16
B 10’
E 81⁄8
90 99/16’’
F 7¾
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
83
25 C 14’
80 91/8’’ 82 NOTE: Pump will pass a
D sphere to 7⁄16" diameter.
811/16’’ 80
70 NOTA: La bomba dejará pasar
20 E 18’ una esfera de hasta 7⁄16 de
75
81/8’’ pulgada de diámetro.
60 F
25
73/4’’
HP
15 50
20
HP
40
15
10
HP
10
30
HP
0 0
0 200 400 600 800 1000 1200 U.S. GPM
GOULDS PUMPS 13
Commercial Water
Performance Curves – 60 Hz, 1750 RPM
Curvas de desempeño – 60 Hz, 1750 RPM
Model 15AI/BF / Size (Tama o) 4 x 6 — 13 NOTE: Not recommended for operation beyond printed
Optional Impeller
H-Q curve.
METERS FEET RPM 1750 Curve (Curva) CN0664R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
METROS PIES IMP. DWG. No. 276-44 Casing Dwg. : 279-19 en la curva H-Q.
200 Ordering Code Dia.
6’ NPSHR — FEET (PIES) Código de pedido Diá.
A 127 8" DIA. 76 % EFF
175 8’ 80 82 A 12 7⁄8"
10’
50 12’ C 12¼
C 121 4" 82 80
150
84 E 113⁄8
16’ 76
E 113 8" G 107⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
20’
40 G 107 8"
72
J 10¼
125
J 101 4" L 9 3 ⁄8
68
100 L 93 8" NOTE: Pump will pass a
30
sphere to 7⁄16" diameter.
NOTA: La bomba dejará pasar
75 una esfera de hasta 7⁄16 de
20 pulgada de diámetro.
15 HP
50
50 HP
40 HP
10
25 30 HP
25 HP
20 HP
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 U.S. GPM
Model 15AI/BF / Size (Tama o) 4 x 6 — 13 NOTE: Not recommended for operation beyond printed
Optional Impeller
H-Q curve.
METERS FEET RPM 1750 Curve (Curva) CN0665R00 NOTA: No se recomienda para funcionamiento superior al impreso Impulsor optativo
METROS PIES IMP. DWG. No. 276-44 Casing Dwg. : 279-19 en la curva H-Q.
200 Ordering Code Dia.
M 131 16 " DIA. 6’ NPSHR — FEET (PIES) Código de pedido Diá.
76 % EFF
8’ 80 M 131⁄16"
175 82
10’
50
B 121 2" 12’ 82 B 12½
D 117 8" 80
150 D 11 7⁄8
16’ 76
84
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
20’ F 111⁄16
F 111 6"
40
125 H 101 2" 72 H 10½
K 9 7⁄8
K 97 8" 68
100 NOTE: Pump will pass a
30
sphere to 7⁄16" diameter.
NOTA: La bomba dejará pasar
75 una esfera de hasta 7⁄16 de
20 pulgada de diámetro.
15 HP
50
50 HP
10
30 HP
25 40 HP
20 HP 25 HP
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 U.S. GPM
GOULDS PUMPS 14
Commercial Water
Performance Curves – 60 Hz, 1780 RPM
Curvas de desempeño – 60 Hz, 1780 RPM
Model 18BF / Size (Tama o) 6 x 8 — 13 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve. Impulsor optativo
METERS FEET RPM 1780 Curve (Curva) CN0445R00 NOTA: No se recomienda para funcionamiento superior
METROS PIES IMP. DWG. No. 278-10 al impreso en la curva H-Q. Ordering Code Dia.
250 Código de pedido Diá.
4’ NPSHR — FEET (PIES)
■A 13"
70
200 ■B 12½
60% EFF. 70 5’
74 78 82 7’ ■C 125⁄16
A 13" DIAMETER
60 175 84
B 12 2" 1 85 ■ D 117⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
9’ E 115⁄8
C 125 16"
50 150 D 117 8" 85 11’ F 111⁄8
E 115 8" 84
G 107⁄8
F 11 8" 1 82
125 H 10½
40 G 107 8"
H 101 2" J 10
J 10" 75
100 HP K 9½
K 9 1 2"
30 60
HP NOTE: Pump will pass a
75 50 sphere to 7⁄8" diameter.
HP
20 40 NOTA: La bomba dejará pasar
HP
50 30 una esfera de hasta 7⁄8 de
HP pulgada de diámetro.
10 ■ Indicates “L” Group pump.
25
■ Indica una bomba Grupo
“L”.
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 U.S. GPM
0 50 100 150 200 250 300 350 400 450 500 m 3 hr
CAPACITY (CAPACIDAD)
Model 19BF / Size (Tama o) 8 x 10 — 13 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve. Impulsor optativo
METERS FEET RPM 1780 Curve (Curva) CN0446R01 NOTA: No se recomienda para funcionamiento superior al
METROS PIES IMP. DWG. No. 278-12 impreso en la curva H-Q. Ordering Code Dia.
60 200 Código de pedido Diá.
60% EFF.
■A 13"
180 8’ NPSHR — FEET (PIES)
A 13" DIA. ■B 12¾
72 11’
50
160 80 14’ ■C 123⁄8
B 123 4"
C 123 8" 85 17’ ■ D 1115⁄16
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
140 86 ■E 1111⁄16
86 20’
40 D 1115 16"
■ F 11¼
85
120 ■ G 107⁄8
E 1111 16" 24’
F 111 4" 80 ■ H 913⁄16
30 100
G 107 8" 15 NOTE: Pump will pass a
0H
P
80
sphere to 7⁄8" diameter.
H 913 16"
12 NOTA: La bomba dejará pasar
20 5H
60 10 P una esfera de hasta 7⁄8 de
0H
P
pulgada de diámetro.
75
40 HP ■ Indicates “L” Group pump.
10 ■ Indica una bomba Grupo
60
20 HP “L”.
0 0
0 500 1000 1500 2000 2500 3000 3500 4000 4500 U.S. GPM 5000
0 100 200 300 400 500 600 700 800 900 1000 m 3 hr 1100
CAPACITY (CAPACIDAD)
GOULDS PUMPS 15
Commercial Water
Performance Curves – 60 Hz, 1780 RPM
Curvas de desempeño – 60 Hz, 1780 RPM
Model 20BF / Size (Tama o) 4 x 6 — 16 NOTE: Not recommended for operation beyond printed Optional Impeller
METERS FEET RPM 1780 Curve (Curva) CN0447R01 H-Q curve. Impulsor optativo
NOTA: No se recomienda para funcionamiento superior al
METROS PIES
IMP. DWG. No. 278-14 impreso en la curva H-Q. Ordering Code Dia.
350 Código de pedido Diá.
70
■A 16"
60% EFF. 5’ NPSHR — FEET (PIES)
300 A 16" DIA. 65
70
■B 155⁄8
60 B 155 8" 73
6’ 74 ■C 153⁄16
C 153 16"
74 ■ D 14½
8’ 73
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
250
50 D 141 2" ■ E 3¾
10’
E 133 4" NOTE: Pump will pass a
200 10 sphere to 5⁄8" diameter.
40 0H
P NOTA: La bomba dejará pasar
una esfera de hasta 5⁄8 de
75 pulgada de diámetro.
30 150 HP
■ Indicates “L” Group pump.
60 ■ Indica una bomba Grupo
HP
20 100 “L”.
10 50
0 0
0 200 400 600 800 1000 1200 U.S. GPM 1400
Model 18BF / Size (Tama o) 6 x 8 — 13 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve. Impulsor optativo
METERS FEET
RPM 1180 Curve (Curva) CN0450R01 NOTA: No se recomienda para funcionamiento
METROS PIES IMP. DWG. No. 278-35 superior al impreso en la curva H-Q. Ordering Code Dia.
90 Código de pedido Diá.
25 L 13" Dia. 60% EFF. 70 2’ NPSHR — FEET (PIES)
L 13"
80 80 M 12½
M 121 2"
84
3’ 86 N 125⁄16
N 12 5
"
70
16
86
20 P 117 8"
P 117⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
4’ E 115⁄8
60 E 115 8" 84
F 111 8" 25
F 111⁄8
H
80 P G 107⁄8
15 50 G 10 8" 7
H 101 2"
H 10½
70
J 10" 20 J 10
40 HP
K 9 2"
1
K 9½
10
30 15 NOTE: Pump will pass a
HP
sphere to 7⁄8" diameter.
20 NOTA: La bomba dejará pasar
5 10 una esfera de hasta 7⁄8 de
HP
7.5 pulgada de diámetro.
HP
10
0 0
0 200 400 600 800 1000 1200 1400 U.S. GPM 1600
0 50 100 150 200 250 300 350 m 3 hr
CAPACITY (CAPACIDAD)
GOULDS PUMPS 16
Commercial Water
Performance Curves – 60 Hz, 1180 RPM
Curvas de desempeño – 60 Hz, 1180 RPM
Model 19BF / Size (Tama o) 8 x 10 — 13 NOTE: Not recommended for operation beyond Optional Impeller
RPM 1180 Curve (Curva) CN0448R02 printed H-Q curve. Impulsor optativo
METERS FEET NOTA: No se recomienda para funcionamiento
METROS PIES IMP. DWG. No. 278-36 superior al impreso en la curva H-Q. Ordering Code Dia.
80 Código de pedido Diá.
3’ NPSHR — FEET (PIES)
J 13" Dia. 60% EFF. J 13"
70 5’
80 K 12¾
70 K 12 4"3
85
L 123 8"
8’
L 123⁄8
20
86 M 1115⁄16
60
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
M 1115 16"
85 N 1111⁄16
N 1111 16"
P 11¼
50
15 P 111 4" 80 Q 107⁄8
10’
Q 107 8" R 913⁄16
40
NOTE: Pump will pass a
40
R 913 16"
HP sphere to 7⁄8" diameter.
10
30 30 NOTA: La bomba dejará pasar
HP una esfera de hasta 7⁄8 de
25 pulgada de diámetro.
20 HP
20
5 HP
15
HP
10
0 0
0 500 1000 1500 2000 2500 3000 U.S. GPM 3500
Model 8AI/BF / Size (Tama o) 11 2 x 2 — 10 NOTE: Not recommended for operation beyond printed Optional Impeller
H-Q curve.
METERS FEET RPM 2900 Curve (Curva) CN0295R00 NOTA: No se recomienda para funcionamiento superior
Impulsor optativo
METROS PIES IMP. DWG. No. 114-51 al impreso en la curva H-Q. Ordering Code Dia.
400
120
NPSHR — FEET (PIES) Código de pedido Diá.
6’ 7’ 8’ A 10 1⁄16"
30 35 40
A 101 16" DIA. 45 48
50
10’ B 93⁄16
51 C 83⁄8
12’
90 300 D 7¾
B 93 16 " 51
E 7¼
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
50
F 7
C 83 8" 48
45% EFF NOTE: Pump will pass a
D 73 4" sphere to 5⁄32" diameter.
60 200
E 71 4"
NOTA: La bomba dejará pasar
F 7" una esfera de hasta 5⁄32 de
25
pulgada de diámetro.
HP
20
HP
15
30 100
H
10
P
HP
0 0
0 50 100 150 200 250 300 U.S. GPM
0 10 20 30 40 50 60 70 m3 hr
CAPACITY (CAPACIDAD)
GOULDS PUMPS 17
Commercial Water
Performance Curves – 50 Hz, 2900 RPM
Curvas de desempeño – 50 Hz, 2900 RPM
Model 7AI/BF / Size (Tama o) 21 2 x 3 — 8 NOTE: Not recommended for operation beyond printed H-Q curve. Optional Impeller
NOTA: No se recomienda para funcionamiento superior al impreso
RPM 2900 Curve (Curva) CN0298R00 en la curva H-Q. Impulsor optativo
IMP. DWG. No. 114-50
METERS FEET Ordering Code Dia.
METROS PIES Código de pedido Diá.
NPSHR — FEET (PIES)
40
5’ 6’ 7’ 8’ A 7 15⁄16"
50 60 10’
200 A 7 15
" DIA. 65 68 70
60 B 7 7⁄16
16
73 75
12’
C 73⁄16
14’
75 D 613⁄16
B 77 "
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
16
73
50 E 63⁄8
C 73 "
20
16
150 F 6 3⁄16
HP
D 613 16 " 70
68 NOTE: Pump will pass a
40 sphere to 5⁄16" diameter.
E 63 8"
F 63 16" NOTA: La bomba dejará pasar
una esfera de hasta 5⁄16 de
15
65
H
100 pulgada de diámetro.
P
30
60% EFF
20 10
HP
7
1 2
H
50
P
10
25
0 50 100 150 200 250 300 350 U.S. GPM
0 10 20 30 40 50 60 70 80 m3 hr
CAPACITY (CAPACIDAD)
Model 21BF / Size (Tama o) 21 2 x 3 — 9 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
RPM 2900 Curve (Curva) CN0673R00 NOTA: No se recomienda para funcionamiento
Impulsor optativo
METERS FEET
METROS PIES IMP. DWG. No. 279-15 superior al impreso en la curva H-Q. Ordering Code Dia.
300 Código de pedido Diá.
90 A 101 16" DIA.
B 97 8" 6’ NPSHR — FEET (PIES) A 10 1⁄16"
64 % EFF
80 8’ B 9 7⁄8
C 91 2" 66
250 D 91 4" 68 C 9½
70
10’
70 E 815 16 "
12’ D 9¼
70
E 815⁄16
200 F 8 2"
1
68
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
60 66 F 8½
G 83 16 "
H 8" 62
G 83⁄16
J 711 "
50 16 56 H 8
150
J 7 11⁄16
40
NOTE: Pump will pass a
sphere to 5⁄16" diameter.
30 100 30 HP
25 HP NOTA: La bomba dejará pasar
20 HP
una esfera de hasta 5⁄16 de
20 pulgada de diámetro.
15 HP
50
10
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 U.S. GPM
0 50 100 m hr3
CAPACITY (CAPACIDAD)
GOULDS PUMPS 18
Commercial Water
Performance Curves – 50 Hz, 2900 RPM
Curvas de desempeño – 50 Hz, 2900 RPM
Model 11AI/BF / Size (Tama o) 21 2 x 3 — 10 NOTE: Not recommended for operation beyond
Optional Impeller
printed H-Q curve.
METERS FEET RPM 2900 Curve (Curva) CN0301R00 NOTA: No se recomienda para funcionamiento superior al Impulsor optativo
METROS PIES IMP. DWG. No. 121-37 impreso en la curva H-Q.
400
Ordering Code Dia.
120 Código de pedido Diá.
NPSHR — FEET (PIES) A 10 1⁄16"
8’
% EFF 50 10’ B 9 7⁄8
60 12’
14’ C 95⁄8
A 10 1 16
" DIA. 63
90 300 D 9
B 97 8" 65 18’
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
C 95 8" 70
E 85⁄8
65 22’
63
F 8¼
D 9"
72
26’
G 8
E 85 8" 60
200 F 81 4"
H 75⁄8
60
G 8"
J 7 1⁄8
H 75 8" 50
NOTE: Pump will pass a
J 71 8"
sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar
30 100 40 una esfera de hasta 5⁄16 de
30
HP pulgada de diámetro.
25 HP
20 HP
15 HP
HP
0 0
0 100 200 300 400 500 600 700 U.S. GPM
Model 16AI/BF / Size (Tama o) 3 x 4 — 8 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
METERS FEET RPM 2900 Curve (Curva) CN376R00 NOTA: No se recomienda para funcionamiento superior Impulsor optativo
METROS PIES
IMP. DWG. No. 277-09 al impreso en la curva H-Q.
Ordering Code Dia.
250
Código de pedido Diá.
70
NPSHR — FEET (PIES)
A 8 1⁄16"
9’
45% EFF
10’ B 7 7⁄16
58 12’
A 81 " DIA. 68 73
60 200
16
D 6¾
76
E 63⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
15’
B 77 " 76
F 515⁄16
50 16
73 19’ G 5½
150
H 51⁄8
D 63 4" 68
40
J 4 5⁄8
E6 3
8 "
58 NOTE: Pump will pass a
F 515 "
30 100
16
sphere to 5⁄16" diameter.
G 51 2"
NOTA: La bomba dejará pasar
30
25
H 51 8"
H
P
pulgada de diámetro.
20
20
H
J 45 8" 15
P
50 10 HP
HP
71
10 2
HP
5
HP
0 0
0 100 200 300 400 500 600 700 800 U.S. GPM
GOULDS PUMPS 19
Commercial Water
Performance Curves – 50 Hz, 2900 RPM
Curvas de desempeño – 50 Hz, 2900 RPM
Model 10AI/BF/ Size (Tama o) 4 x 5 — 8 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
METERS FEET RPM 2900 Curve (Curva) CN0319R00 NOTA: No se recomienda para funcionamiento superior
Impulsor optativo
METROS PIES
IMP. DWG. No. 120-08 al impreso en la curva H-Q. Ordering Code Dia.
60 200
NPSHR — FEET (PIES) Código de pedido Diá.
50 60 15’
70 75 78 A 7 7⁄8"
A 77 8" DIA. 80
B 73 4" 81 B 7¾
50 18’
C 71 2"
20’ C 7½
81
150 D 71 4" 22’
D 7¼
80
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
24’
E 7
40 E 7"
78
F 63 4 " 26’ F 6¾
75
G 6 2"
1 70
G 6½
100
H 61⁄16
30 H6 1
16 "
60% EFF
J 5¾
J 53 4 "
NOTE: Pump will pass a
sphere to 5⁄16" diameter.
20
NOTA: La bomba dejará pasar
40
una esfera de hasta 5⁄16 de
HP
50 30
HP pulgada de diámetro.
25
10 HP
20
HP
15
HP
0 0
0 200 400 600 800 1000 1200 1400 U.S. GPM
Model 13AI/BF / Size (Tama o) 21 2 x 3 — 13 NOTE: Not recommended for operation beyond printed H-Q curve. Optional Impeller
NOTA: No se recomienda para funcionamiento superior al impreso en
METERS FEET
RPM 1450 Curve (Curva) CN0304R00 la curva H-Q.
Impulsor optativo
METROS PIES IMP. DWG. No. 276-46 Ordering Code Dia.
160
Código de pedido Diá.
NPSHR — FEET (PIES) 6’
A 131⁄16"
50 55 B 12¾
40 A 131 " DIA. 8’
16
60 62
C 117⁄8
120 B 12 4"
3
10’ D 113⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
E 97⁄8
C 117 8"
30
62 F 9 3⁄8
D 113 8" 12’
60 NOTE: Pump will pass a
80
sphere to 5⁄16" diameter.
E 97 8" 55 NOTA: La bomba dejará pasar
20 F9 3
8 "
50 una esfera de hasta 5⁄16 de
pulgada de diámetro.
40% EFF
40
15 HP
10
10
7
HP
1 2
5
HP
HP
0 0
0 100 200 300 400 500 600 700 U.S. GPM
GOULDS PUMPS 20
Commercial Water
Performance Curves – 50 Hz, 1450 RPM
Curvas de desempeño – 50 Hz, 1450 RPM
Model 12AI/BF / Size (Tama o) 3 x 4 — 10 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
METERS FEET RPM 1450 Curve (Curva) CN0315R00 NOTA: No se recomienda para funcionamiento superior Impulsor optativo
METROS PIES IMP. DWG. No. 120-05 al impreso en la curva H-Q. Ordering Code Dia.
Código de pedido Diá.
NPSHR — FEET (PIES) 5’ A 10 1⁄16"
25 6’
80 50 60 68 70 B 9¾
73 7’
A 101 " DIA. 75
16
77 8’ C 9
B 93 4"
D 85⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
20 77 10’ E 81⁄8
60 C 9" 75
73
F 7 5⁄8
12’
D 85 8" 70 NOTE: Pump will pass a
68
sphere to 3⁄8" diameter.
15 E 81 8" NOTA: La bomba dejará pasar
60
una esfera de hasta 3⁄8 de
F 75 8"
40 pulgada de diámetro.
50% EFF
10
10
HP
20
3
7
1 2
H
P
HP
5
10 HP
0 100 200 300 400 500 600 U.S. GPM
Model 14AI/BF / Size (Tama o) 3 x 4 — 13 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
METERS FEET
RPM 1450 Curve (Curva) CN0317R00 NOTA: No se recomienda para funcionamiento superior Impulsor optativo
METROS PIES IMP. DWG. No. 276-45 al impreso en la curva H-Q.
160
Ordering Code Dia.
Código de pedido Diá.
NPSHR — FEET (PIES) A 13 1⁄16"
3’
60 B 12 9⁄16
40 70 4’
73 C 125⁄16
A 131 16 " DIA. 5’
120 75 D 12
B 129 16" 6’
76
C 125 16" 75 F 115⁄16
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
7’
D 12" 73
30 8’
G 10¾
70
F 115 16 "
H 101⁄8
80 G 103 4"
J 91⁄8
60
H 101 8"
K 811⁄16
20 30% EFF L 8
J 91 8"
M 7 9⁄16
K8 11
16 "
L 8" NOTE: Pump will pass a
40 M 73 "
16
sphere to 3⁄8" diameter.
20
10 15
NOTA: La bomba dejará pasar
HP
HP
10
HP
una esfera de hasta 3⁄8 de
71 pulgada de diámetro.
2
HP
5H
0 P
0
100 200 300 400 500 600 700 800 U.S. GPM
GOULDS PUMPS 21
Commercial Water
Performance Curves – 50 Hz, 1450 RPM
Curvas de desempeño – 50 Hz, 1450 RPM
Model 17BF / Size (Tama o) 4 x 6 — 10 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
RPM 1450 Curve (Curva) NOTA: No se recomienda para funcionamiento superior Impulsor optativo
IMP. DWG. 277-78 al impreso en la curva H-Q. Ordering Code Dia.
METERS FEET Código de pedido Diá.
METROS PIES
100 A 101⁄16"
30
B 99⁄16
NPSHR — FEET (PIES) C 91⁄8
6’ D 811⁄16
80
E 81⁄8
59% EFF. 69
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
74 79
F 7¾
A 101/16’’ DIA. 81 82 7’
20
10’ NOTE: Pump will pass a
60 B 99/16’’ 15 HP sphere to 7⁄16" diameter.
82
81
C 91/8’’ 13’ NOTA: La bomba dejará pasar
D 811/16’’ 79 una esfera de hasta 7⁄16 de
pulgada de diámetro.
E 81/8’’ 74
40
F 73/4’’
10
10 HP
71/2 HP
20 5 HP
0 0
0 100 200 300 400 500 600 700 800 900 U.S. GPM
Model 15AI/BF / Size (Tama o) 4 x 6 — 13 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve.
METERS FEET
RPM 1450 Curve (Curva) CN0322R00 NOTA: No se recomienda para funcionamiento superior Impulsor optativo
METROS PIES IMP. DWG. No. 276-44 al impreso en la curva H-Q. Ordering Code Dia.
150
Código de pedido Diá.
140
72 % EFF 6’ NPSHR — FEET (PIES) M 131⁄16"
40 130 M 13 " DIA.
1
16
78 7’
82
8’ A 12 7⁄8
A 127 8" 10’
120 B 12½
B 121 2"
82 C 12¼
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
L 9 3⁄8
40
30 HP
10 NOTE: Pump will pass a
30 25 HP
sphere to 7⁄16" diameter.
10 HP 20 HP
20 NOTA: La bomba dejará pasar
15 HP
10
una esfera de hasta 7⁄16 de
pulgada de diámetro.
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 U.S. GPM
GOULDS PUMPS 22
Commercial Water
Performance Curves – 50 Hz, 1450 RPM
Curvas de desempeño – 50 Hz, 1450 RPM
Model 18BF / Size (Tama o) 6 x 8 — 13 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve. Impulsor optativo
METERS FEET RPM 1450 Curve (Curva) CN0451R00 NOTA: No se recomienda para funcionamiento superior
METROS PIES IMP. DWG. No. 278-10 al impreso en la curva H-Q. Ordering Code Dia.
140 Código de pedido Diá.
40 2’ NPSHR — FEET (PIES) ■A 13"
60% EFF.
A 13" DIA. 70
120 80
■B 12½
4’
35 B 121 2" 84 ■C 125⁄16
85
C 125 16" 85 6’ ■ D 117⁄8
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
Model 19BF / Size (Tama o) 8 x 10 — 13 NOTE: Not recommended for operation beyond Optional Impeller
printed H-Q curve. Impulsor optativo
METERS FEET RPM 1450 Curve (Curva) CN0449R00 NOTA: No se recomienda para funcionamiento
METROS PIES
IMP. DWG. No. 278-12 superior al impreso en la curva H-Q. Ordering Code Dia.
120 Código de pedido Diá.
9’ NPSHR — FEET (PIES)
A 13" DIA.
60% EFF. ■A 13"
70
B 123 4"
80 12’ ■B 12¾
30
100 C 123 8" 85 15’ ■ C 123⁄8
86 ■D 1115⁄16
D 1115 16"
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
25 ●E 1111⁄16
85
80 E 1111 16" 18’
●F 11¼
F 11 4"
1
80 ● G 107⁄8
20 G 107 8"
75
●H 913⁄16
60 HP
H 913 16"
NOTE: Pump will pass a
15 60
70 HP sphere to 7⁄16" diameter.
40 50 NOTA: La bomba dejará pasar
60 HP una esfera de hasta 7⁄16 de
10
40 pulgada de diámetro.
HP
30
■ Indicates “L” Group pump.
20 HP
5 ■ Indica una bomba
Grupo “L”.
● For close coupled version,
0 0 consult factory.
0 500 1000 1500 2000 2500 3000 3500 U.S. GPM 4000
● Para la versión compacta,
0 100 200 300 400 500 600 700 800 m 3 hr 900 consulte con la fábrica.
CAPACITY (CAPACIDAD)
GOULDS PUMPS 23
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
Model 8BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
Size (Tama o) 1 2 x 2 — 10
1 (Velocidad variable) NOTA: No se recomienda para funcionamiento
FEET
PIES
101 16 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0453R01 superior al impreso en la curva H-Q.
45
3200 RPM
50
3000 RPM
300 45
2800 RPM
2600 RPM
30
HP
2400 RPM
200
25
HP
2200 RPM
20
2000 RPM
HP
1800 RPM
15
HP
100 1600 RPM 10
HP
5
HP
0
0 25 50 75 100 125 150 175 200
CAPACITY (CAPACIDAD) U.S. GPM
Model 7BF Variable Speed NOTE: Not recommended for operation beyond
Size (Tama o) 21 2 x 3 — 8 (Velocidad variable) printed H-Q curve.
NOTA: No se recomienda para funcionamiento
715 16 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0454R01 superior al impreso en la curva H-Q.
NPSHR — FEET (PIES)
FEET
PIES
30
20
10
50% EFF. 60 65 70
300 3600 RPM (MAXIMUM) 0
75
3400 RPM
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
250
3200 RPM
30
3000 RPM HP
200 25
2800 RPM HP
2600 RPM 20
HP
150
2400 RPM 15
HP
2200 RPM
100 2000 RPM 10
HP
1800 RPM 7.5
HP
1600 RPM
5H
50 3H P
P
0
0 50 100 150 200 250 300 350 400 U.S. GPM 450
CAPACITY (CAPACIDAD)
GOULDS PUMPS 24
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
2800 RPM
250
2600 RPM 66
Model 11BF Variable Speed NOTE: Not recommended for operation beyond
Size (Tama o) 21 2 x 3 — 10 (Velocidad variable) printed H-Q curve.
NOTA: No se recomienda para funcionamiento
FEET 101 16 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0455R01 superior al impreso en la curva H-Q.
2600 RPM 65
250
2400 RPM
60
200
HP
2200 RPM
50
2000 RPM 60
HP
150
1800 RPM
40
30
HP
20 25
15 HP HP
50 HP
10
HP
0
0 100 200 300 400 500 600 700 U.S. GPM 800
CAPACITY (CAPACIDAD)
GOULDS PUMPS 25
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
Model 13BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET
Size (Tama o) 2 2 x 3 — 13
1 (Velocidad variable) NOTA: No se recomienda para funcionamiento
PIES
131 16 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0456R01 superior al impreso en la curva H-Q.
300 65
2000 RPM
250 63
1800 RPM 60
200
50
1600 RPM HP
150 50
1400 RPM 40
HP
100 30
25 HP
20 HP
15 HP
50 HP
10
HP
0
0 100 200 300 400 500 600 U.S. GPM 700
CAPACITY (CAPACIDAD)
Model 16BF Variable Speed NOTE: Not recommended for operation beyond
Size (Tama o) 3 x 4 — 8 (Velocidad variable) printed H-Q curve.
NOTA: No se recomienda para funcionamiento superior
FEET 81 16 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0457R01 al impreso en la curva H-Q.
PIES
NPSHR — FEET (PIES)
350 30
58% EFF.
20
3600 RPM (MAXIMUM) 68 10
73
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
300 0
3400 RPM 76
1800 RPM 30
HP
25 HP
20 HP
50 1600 RPM 15 HP
5 10 HP
HP 7.
5 HP
HP
0
0 100 200 300 400 500 600 700 800 U.S. GPM 900
CAPACITY (CAPACIDAD)
GOULDS PUMPS 26
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
Model 12BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET
Size (Tama o) 3 x 4 — 10 (Velocidad variable) NOTA: No se recomienda para funcionamiento superior
PIES
91 8 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0458R01 al impreso en la curva H-Q.
500
350 80
3200 RPM 78
300 75
3000 RPM
70
250 2800 RPM
60
2600 RPM
200
2400 RPM
Model 14BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET Size (Tama o) 3 x 4 — 13 (Velocidad variable) NOTA: No se recomienda para funcionamiento
PIES 131 16" Dia. Impeller (Di . Impulsor) Curve (Curva) CN0459R01 superior al impreso en la curva H-Q.
500
75
60
250 2000 RPM
50
200 1800 RPM
12
1600 RPM
0
150
HP
1400 RPM
10
0
100
HP
75
60 HP
50 HP
50 40 HP
30 HP
20 HP
HP
0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400
CAPACITY (CAPACIDAD) U.S. GPM
GOULDS PUMPS 27
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
Model 10BF Variable Speed NOTE: Not recommended for operation beyond
Size (Tama o) 4 x 5 — 8 (Velocidad variable) printed H-Q curve.
NOTA: No se recomienda para funcionamiento superior
FEET
PIES
77 8 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0460R01 al impreso en la curva H-Q.
80
200 3000 RPM 82
2800 RPM
Model 17BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET
Size (Tama o) 4 x 6 — 10 (Velocidad variable) NOTA: No se recomienda para funcionamiento superior
PIES 101 16 Dia. Impeller (Di . Impulsor) Curve (Curva) CN0461R01 al impreso en la curva H-Q.
200 30 NPSHR — FEET (PIES)
20
60% EFF.
2200 RPM (MAXIMUM) 10
175 75 0
80
83
80
125
1800 RPM
75
100
1600 RPM
50
HP
75 1400 RPM 40
HP
30
HP
50
20
15 HP
HP
25 10
HP
0
0 200 400 600 800 1000 1200 1400 U.S. GPM 1600
CAPACITY (CAPACIDAD)
GOULDS PUMPS 28
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
Model 15BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET Size (Tama o) 4 x 6 — 13 (Velocidad variable) NOTA: No se recomienda para funcionamiento
PIES 131 16" Dia. Impeller (Di . Impulsor) Curve (Curva) CN0462R02 superior al impreso en la curva H-Q.
400 30
72
250 2000 RPM
1800 RPM
200
60
1600 RPM
150
12
5
HP
100
10
0
HP
60 75
50 50 HP HP
40 HP
HP
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
CAPACITY (CAPACIDAD) U.S. GPM
Model 18BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET Size (Tama o) 6 x 8 — 13 (Velocidad variable) NOTA: No se recomienda para funcionamiento superior
PIES
13" Dia. Impeller (Di . Impulsor) Curve (Curva) CN0463R01 al impreso en la curva H-Q.
550
85
350 84
2400 RPM
82
300
2200 RPM
25
250 2000 RPM 0H
P
20
0H
200 1800 RPM P
15
1600 RPM 0H
150 12 P
5H
P
10
100 75 0H
HP P
50
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200
CAPACITY (CAPACIDAD) U.S. GPM
GOULDS PUMPS 29
Commercial Water
Performance Curves – Variable Speed
Curvas de desempeño – Velocidad variable
Model 19BF Variable Speed NOTE: Not recommended for operation beyond
printed H-Q curve.
FEET Size (Tama o) 8 x 10 — 13 (Velocidad variable) NOTA: No se recomienda para funcionamiento superior
PIES 13" Dia. Impeller (Di . Impulsor) Curve (Curva) CN0464R01 al impreso en la curva H-Q.
350
250
35
0H
225 P
2000 RPM
30
200 0H
P
25
175 1800 RPM 85 0H
P
150 80
1600 RPM
20
125 0H
P
1400 RPM
100
15
0H
75 P
50 10
HP 0H
50 75 P
HP
25
0
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
CAPACITY (CAPACIDAD) U.S. GPM
Model 20BF Variable Speed NOTE: Not recommended for operation beyond
FEET Size (Tama o) 4 x 6 — 16 (Velocidad variable) printed H-Q curve.
NOTA: No se recomienda para funcionamiento superior
PIES
16" Dia. Impeller (Di . Impulsor) Curve (Curva) CN0465R00 al impreso en la curva H-Q.
700
15
NPSHR — FEET (PIES)
600 10
500 0
TOTAL DYNAMIC HEAD (CARGA DIN MICA TOTAL)
60% EFF. 65
2200 RPM (MAXIMUM) 70 73
74
400 2000 RPM 73
17
1800 RPM 5H
300 15 P
0H
12 P
1600 RPM 5H
10 P
200 1400 RPM 0H
P
75
HP
50
100 HP
0
0 200 400 600 800 1000 1200 1400 1600
CAPACITY (CAPACIDAD) U.S. GPM
GOULDS PUMPS 30
Commercial Water
3656 M & L-Group Materials of Construction
Materiales de construcción - Grupo M y L, modelo 3656
108
105 106 107
ANSI 1045 steel motor
shaft extension (typical)
101
126
ANSI 1045 Extensi n del eje
del motor de acero (t pica)
178
198
353
199
355
126
103
383
Packed Box Arrangement
408 Caja prensaestopas
370 371
Item No. Description Materials, Materiales Material Code Engineering Standard
No. Descripción All Iron Bronze Fitted Código de material Norma de ingeniería
Ítem Todo Accesorios Cast iron ASTM A48 CL30
1003
hierro de bronce Hierro fundido ASTM A48 CL20
100 Casing, Carcasa 1003 Bismuth Bronze – Lead Free,
1618
Bismuth Bronze – Lead Free
101 Impeller, Impulsor 1101 Cast iron ASTM A48 CL20
Casing wear ring, 1001
Hierro fundido ASTM A48 CL20
103 1001 1618
Anillo de desgaste de la carcasa ASTM B584, Modified C87500 – Lead Free
1101
Adapter/seal housing, ASTM B584, modified C87500 – Lead Free
108 1001 Packed Box Arrangement, Caja prensaestopas
Adaptador/Cubierta del sello
126 Shaft sleeve, Camisa del eje Item No. Description Materials
No. Ítem Descripción Materiales
178 Impeller key, Chaveta del impulsor AISI Type 300 Series SS
Acero inoxidable serie Lantern ring
198 Impeller bolt, Tornillo del impulsor 105 Teflon®
AISI tipo 300 Aro de linterna
199 Impeller washer, Arandela del impulsor Packing, 5 rings Teflon Impregnated
Hex head cap screw (adapter to case), Tornillo 106 Empaquetadura, 5 aros Impregnado de Teflon
370 107 Gland, Casquillo AISI 316SS
de cabeza hexagonal (del adaptador a la cubierta)
Steel Zinc Platted Grade 5 Shaft sleeve
Hex head cap screw (adapter to motor),
371 Tornillo de cabeza hexagonal Acero SAE 1200 grado 5 126 Camisa del eje
(del adaptador al motor) Gland stud AISI Type 300 Series Stainless Steel
353 Perno del casquillo Acero inoxidable serie AISI tipo 300
383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello
Gland nut
408
Pipe plug ¼" or 3⁄8", Tapón de tubos de Zinc Platted Steel 355 Tuerca del casquillo
¼ de pulgada ó 3⁄8 de pulgada Zinc Platted Steel
BUNA-N – Standard, NOTE: NOTA:
513 O-ring, Anillo en O EPR – Optional Seal housing wear ring (item El anillo de desgaste del compartimiento
Viton – Optional number 203) not shown. See repair de sello (ítem número 203) no se muestra.
parts page for detail. (Required for Consulte la página de piezas de repuesto
all models except 3 x 4 – 10.) para mayor detalle. (Se requiere para todos
los modelos con excepción del 3 x 4 – 10).
Mechanical Seal Chart, Type 21, Tabla para sello mecánico, tipo 21
Item Part No., Pieza Número
No., M-Group, Grupo-M L-Group, Grupo-L Rotary, Stationary, Elastomers, Metal Parts, Intended Duty,
No. 250JM-360TCZ All motors,
180JM-210JM 210JP-360TCZ* Rotativo Estacionario Elastómeros Partes Metálicas Servicio previsto
Todos los motores
Ítem 180JP-210CZ* M Bearing Frame, L Bearing Frame,
Bastidor de cojinetes M Bastidor de cojinetes L
10K13 10K16 10K84 Ceramic, Cerámica BUNA-N Standard, Estándar
Consult Factory, Carbon, High Temp, Caustic,
10K19 10K20 Sil-Carbide, EPR 316 SS, Alta temp/Caustic
Consultar con la fábrica Carbone
383 Carburo de 316 Acero inoxidable
10K27 10K45 10K112 Abrasive,
silicona Viton Abrasivo
10K64 10K65 10K144 Sil-Carbide
15K17 15K3 15K4 Packed Box Design with BUNA O-Ring, Diseño de prensaestopas empacado con anillo en O de BUNA
* All Packed Box units use JP style motors. Todas las unidades de prensaestopas empacado utilizan motores estilo JP.
GOULDS PUMPS 31
Commercial Water
3756 M & L-Group Materials of Construction
Materiales de construcción - Grupo M y L, modelo 3756
108
105 106 107
100
134 112 126
101
178
353
198
199 355
103 333A
L-Group Arrangement
126 Arreglo de grupo en L
382 Packed Box Arrangement
Caja prensaestopas
383
Item No. Description Materials, Materiales Item No. Description Materials, Materiales
No. Descripción All Iron Bronze Fitted No. Descripción All Iron Bronze Fitted
Ítem Todo Accesorios Ítem Todo Accesorios
hierro de bronce hierro de bronce
100 Casing, Carcasa 1003 122 Pump shaft, Eje de la bomba Steel, Acero
101 Impeller, Impulsor 1101 168 Ball bearing (inboard), Cojinete de bolas (interior) Steel, Acero
Casing wear ring, 112 Ball bearing (outboard), Cojinete de bolas (exterior) Steel, Acero
103 1618
Anillo de desgaste de la carcasa Steel Zinc Platted
1001 382 Retaining ring, bearing, Anillo de retención, cojinete
Adapter/seal housing, Grade 5,
108 1001 Acero Zinc
Adaptador/Cubierta del sello Hex head cap screw (bearing frame to cover), Tornillo Platted
370C
126 Shaft sleeve, Camisa del eje de cabeza hexagonal (de la cubierta de cojinetes al marco) grado 5
178 Impeller key, Chaveta del impulsor AISI Type 300 Series SS 333A Lip seal, Sello con reborde BUNA-N
Acero inoxidable serie
198 Impeller bolt, Tornillo del impulsor AISI tipo 300 193 Grease fitting, Accesorio grasa Steel, Acero
199 Impeller washer, Arandela del impulsor 123 V-ring deflector, Anillo en V (Deflector) BUNA-N
Hex head cap screw (adapter to case),Tornillo Packed Box Arrangement, Caja prensaestopas
370
de cabeza hexagonal (del adaptador a la cubierta) Item No. Description Materials
Steel Zinc Platted Grade 5 No. Ítem Descripción Materiales
Hex head cap screw (adapter to bearing frame),
Acero Zinc Platted grado 5
370B Tornillo de cabeza hexagonal Lantern ring
105 Teflon®
(del adaptador al motor) Aro de linterna
383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello Packing, 5 rings Teflon Impregnated
106 Empaquetadura, 5 aros Impregnado de Teflon
Pipe plug ¼" or 3⁄8", Tapón de tubos de Zinc PlattedSteel,
408 107 Gland, Casquillo AISI 316SS
¼ de pulgada ó 3⁄8 de pulgada Zinc Platted Acero
126 Shaft sleeve
BUNA-N – Standard, Standard Camisa del eje
513 O-ring, Anillo en O EPR – Optional, Optional 353 Gland stud AISI Type 300 Series Stainless Steel
Viton – Optional, Optional Perno del casquillo Acero inoxidable serie AISI tipo 300
Power End Components, Componentes del extremo de fuerza 355 Gland nut
Tuerca del casquillo
228 Bearing frame, Marco de cojinete Cast iron ASTM A48 CL20
Material Code Engineering Standard
134 Bearing cover, Cubierta del cojinete Hierro fundido ASTM A48 CL20
Código de material Norma de ingeniería
1001 Cast iron ASTM A48 CL20
Hierro fundido ASTM A48 CL20
Sil-Brass ASTM B584, Modified C87500 –
1102 Lead Free
Sil-Brass ASTM B584, Modified C87500 –
Lead Free
1003 Cast Iron ASTM A48 CL30
Cast Iron ASTM A48 CL30
1618 Bismuth Bronze – Lead Free
Bismuth Bronze – Lead Free
GOULDS PUMPS 32
Commercial Water
3756 M & L-Group SAE Drive Materials of Construction
Materiales de construcción - Grupo M y L, modelo 3756
333A
228 108
513 371C 382 193
123 105 106 107
100
165
126
101 126
178
353
198
355
103 112
Item No. Description Materials, Materiales Item No. Description Materials, Materiales
No. Descripción All Iron Bronze Fitted No. Descripción All Iron Bronze Fitted
Ítem Todo Accesorios Ítem Todo Accesorios
hierro de bronce hierro de bronce
100 Casing, Carcasa 1003 122 Pump shaft, Eje de la bomba AISI 4140
101 Impeller, Impulsor 1101 168 Ball bearing (inboard), Cojinete de bolas (interior) Steel, Acero
Casing wear ring, 112 Ball bearing (outboard), Cojinete de bolas (exterior) Steel, Acero
103 1618
Anillo de desgaste de la carcasa
1001 382 Retaining ring, bearing, Anillo de retención, cojinete Steel SAE 1200
Adapter/seal housing, Grade 5,
108 1001
Adaptador/Cubierta del sello 370C Hex head cap screw (bearing frame to cover), Tornillo Acero SAE 1200
grado 5
126 Shaft sleeve, Camisa del eje AISI Type 300 Series SS de cabeza hexagonal (de la cubierta de cojinetes al marco)
178 Impeller key, Chaveta del impulsor Acero inoxidable serie 333A Lip seal, Sello con reborde BUNA-N
198 Impeller nut, Tornillo del impulsor AISI tipo 300 193 Grease fitting, Accesorio grasa Steel, Acero
370 Hex head cap screw (adapter to case),Tornillo 123 V-ring deflector, Anillo en V (Deflector) BUNA-N
de cabeza hexagonal (del adaptador a la cubierta) Steel Zinc Platted Grade 5 Packed Box Arrangement, Caja prensaestopas
370B Hex head cap screw (adapter to bearing frame), Acero Zinc Platted Item No. Description Materials
Tornillo de cabeza hexagonal grado 5 No. Ítem Descripción Materiales
(del adaptador al motor) 105 Lantern ring
Teflon®
383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello
Aro de linterna
408 Pipe plug ¼" or 3⁄8", Tapón de tubos de Zinc Platted Steel, 106 Packing, 5 rings Teflon Impregnated
¼ de pulgada ó 3⁄8 de pulgada Zinc Platted Acero Empaquetadura, 5 aros Impregnado de Teflon
513 O-ring, Anillo en O BUNA-N – Standard, Standard 107 Gland, Casquillo AISI 316SS
EPR – Optional, Optional 126 Shaft sleeve
Viton – Optional, Optional Camisa del eje
353 Gland stud AISI Type 300 Series Stainless Steel
Power End Components, Componentes del extremo de fuerza
Perno del casquillo Acero inoxidable serie AISI tipo 300
228 Bearing frame, Marco de cojinete 1003
355 Gland nut
134 Bearing cover, Cubierta del cojinete 1001 Tuerca del casquillo
340 Adapter/Engine, Adaptador/Motor 1003 Material Code Engineering Standard
371C Hex head cap screw (adapter to bearing frame) Steel SAE 1200 grade 5 Código de material Norma de ingeniería
501N Cover/adapter, Cubierta/Adaptador Galvinized steel Cast iron ASTM A48 CL20
327C Cap screw (cover to adapter) Steel SAE 1200 grade 5 1001
Hierro fundido ASTM A48 CL20
Cast iron ASTM A48 CL30
1003
Hierro fundido ASTM A48 CL30
Sil-Brass ASTM B584, Modified C87500 –
Lead Free
1101
Sil-Brass ASTM B584, Modified C87500 –
Lead Free
Bismuth Bronze – Lead Free,
1618
Bismuth Bronze – Lead Free
GOULDS PUMPS 33
Commercial Water
3656 M & L-Group Dimensions and Weights Mechanical Seal
Grupo M y L, modelo 3656 - Peso y dimensiones Sello mecánico
GOULDS PUMPS 34
Commercial Water
3656 M & L-Group Dimensions and Weights Packed Box
Grupo M y L, modelo 3656 - Peso y dimensiones Caja prensaetopas
AB DISCHARGE CP
MAX Z R DESCARGA MAX
Y W
X SUCTION
SUCCIÓN
PUMP CENTERLINE
LÕNEA CENTRAL DE LA BOMBA
P MAX
K 2 HOLES DC DD
.62 DIA. G D MAX
J F F H - 4 HOLES
E E L 4 ORIFICIOS
N A B
M NPT DRAIN ADAPTER FOOT
ADAPTER FOOT DRENAJE NPT BASE ADAPTADORA
BASE ADAPTADORA
Pump Dimensions and Weights, Peso y dimensiones de la bomba
NPT Drain Wt. (lbs.) Motor Frame, Bastidor del motor
Pump Suction Discharge CP DC
Bomba Succión Descarga Max. Max. DD J K M N R Drenaje W X Y Z Pesos L
NPT (libras) 210 250/280 320 360 400 440
1½ x 2 –10 2* 1½* 341⁄8 6¾ 57⁄8 — — — — 1¼ 77⁄8 3 5½ 105 163⁄8 12¾ — — — —
¼ 6
2½ x 3 – 8 3* 2½* 345⁄8 6¼ 5¼ — — — — 113⁄16 8 33⁄8 5 90 167⁄8 13¼ — — — —
2½ x 3 – 9
373⁄8 71⁄8 6 — — — — 7½ 2¾ 5½ 95 161⁄8 12½ 157⁄8 16½ — —
2½ x 3 – 10 3 2½ 3½ 3
⁄8 77⁄8
2½ x 3 – 13 34 ⁄8 8 ⁄8
1 7
7 ⁄8 — — — —
5
9 3 7½ 155 163⁄8 12¾ — — — —
3 x 4 – 8 347⁄16 6¼ 53⁄8 — — — —
¼ 83⁄16 7 55⁄8 90 1611⁄16 131⁄16 16½ — — —
3 x 4 – 10 4 3 34¼ 7 3⁄8 6½ — — — — 3¾ 8 7½ 5½ 110 16½ 127⁄8 — — — —
3
3 x 4 – 13 371⁄8 9½ 81⁄8 — — — — 77⁄8 9 7½ 170 163⁄8 12¾ — — — —
4 x 5 – 8 5 38 ⁄8 6 ⁄8
1 7
5¾ — — — —
8 ⁄8 8
3
5 110 167⁄8 13¼ 165⁄8 17¼ — —
4 x 6 – 10 4 34¾ 85⁄8 7½ — — — — 4½ 3
⁄8 83⁄8 8½ 31⁄8 7 145 17 133⁄8 — — — —
4 x 6 – 13 6 357⁄8 9¾ 81⁄8 — — — — 81⁄8 9 3 7½ 185 163⁄8 12¾ 161⁄8 — — —
■ 4 x 6 – 16 471⁄8 12¾ 11 115⁄16 9¾ 8 7 85⁄8 12 4 10½ 390 1611⁄16 173⁄16 1711⁄16 185⁄16 19¼ —
■ 6 x 8 – 13 8 6 457⁄8 12¾ 10½ 23⁄8 7½ 6½ 5½ 5½ 83⁄8 11 37⁄8 8¾ 290 16¾ 17¼ 17¾ 183⁄8 187⁄8 19¾
■ 8 x 10 – 13 10 8 481⁄8 14¾ 13 23⁄8 7½ 6½ 5½ 6¾ 85⁄8 12¾ 4 10 520 171⁄8 175⁄8 181⁄8 18¾ 19¼ 201⁄8
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.
* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.
■ Indicates “L” Group pump (dimensions valid for packed box or mechanical seal)., ■ Indica una bomba Grupo “L” (dimensiones válidas para caja empacada o sella mecánico).
Motor Dimensions and Weights (may vary with manufacturer)*, Peso y dimensiones del motor (pueden variar de acuerdo al fabricante) *
Horsepower
Motor Frame 3500 RPM 1750 RPM
A AB B D E F G H P Wt.
Bastidor
Max. Max. 1 Phase 3 Phase 1 Phase 3 Phase Max.
del motor
ODP TEFC ODP TEFC ODP TEFC ODP TEFC
213JP 2¾ 7½ — 10 — 5 — 7½ 7½ 125
9½ 73⁄8 8 5¼ 4¼ ¼ 13
⁄32 95⁄8
215JP 3½ 10 — 15 10 & 15 7½ & 10 — 10 10 155
254JP 41⁄8 — — 20 — — — 15 15 255
11¼ 9 11¾ 6¼ 5 11½
256JP 5 — — 25 20 — — 20 20 280
¼ 17
⁄32
284JP 4¾ — — 30 25 — — 25 25 410
12¼ 12¼ 12¼ 7 5½ 13¼
286JP 5½ — — 40 30 — — 30 30 425
324JP 5¼ — — 50 40 — — 40 40 560
13¼ 13¼ 13½ 8 6¼ 5
⁄16 151⁄8
326JP
6
— — 60 50 — — 50 50 590
21
⁄32
364TCZ 55
⁄8 — — 75 60 & 75 — — 60 60 775
17½ 143⁄8 151⁄8 9 7 1 183⁄8
365TCZ 61⁄8 — — — — — — 75 75 1005
404TCZ 5 61⁄8 — — — — — — 100 100 1110
19½ 17½ 16 ⁄8 10 8 1 201⁄8
405TCZ 67⁄8 — — — — — — 125 — 1163
13
⁄16
444TCZ 7¼ — — — — — — 150 125 1600
21½ 191⁄8 19½ 11 9 1 22½
445TCZ 8¼ — — — — — — — 150 1708
NOTE: torque., ½ - 13 casing bolts to 90 NOTA: pernos de 3/8 de pulgada a una torsión
1. All pumps shipped in vertical ft./lbs. torque. 1. Todas las bombas se embarcan con de 37 pies/libra, y los 13 pernos de 1/2
discharge position. For other orien- 2. Dimensions in inches, weight in la descarga en posición vertical. Para pulgada a 90 pies/libra.
tations, remove casing bolts, rotate pounds. otras orientaciones, retire los pernos de 2. Dimensiones en pulgadas, peso en
to desired position, and tighten 3. Not to be used for construction la carcasa, haga rotar la descarga hasta libras.
3
⁄8 - 16 casing bolts to 37 ft./lbs. purposes. la posición deseada y ajuste los 16 3. No utilizar con fines de construcción.
GOULDS PUMPS 35
Commercial Water
3756 M & L-Group Dimensions and Weights Mechanical Seal
Grupo M y L, modelo 3756 - Peso y dimensiones Sello mecánico
CP
DISCHARGE
Z R DESCARGA Y W
37⁄8
X
PUMP SUCTION 1.625 DIA.
CENTERLINE SUCCIÓN 1.624
LÍNEA
CENTRAL
DE LA BOMBA KEYWAY
3
⁄16 x 3⁄8
2 HOLES DC DD CHAVETERO
.62 DIA. K MAX 3
⁄16 x 3⁄8
6¼ 4 HOLES
9
⁄16 DIA.
4 ORIFICIOS
DRAIN PLUG ½
TAPÓN DE J
N 3½ 3½ DRENAJE
M L 6½ 1
8½ 8½
ADAPTER FOOT ADAPTER FOOT
BASE ADAPTADORA BASE ADAPTADORA
GOULDS PUMPS 36
Commercial Water
3756 M & L-Group Dimensions and Weights Packed Box
Grupo M y L, modelo 3756 - Peso y dimensiones Caja prensaestopas
CP
DISCHARGE
Z R DESCARGA Y W
37⁄8
X
SUCTION 1.625 DIA.
PUMP SUCCIÓN
CENTERLINE 1.624
LÕNEA
CENTRAL KEYWAY
DE LA BOMBA 3
⁄16 x 3⁄8
2 HOLES DC DD CHAVETERO
.62 DIA. K MAX 3
⁄16 x 3⁄8
6¼ 4 HOLES
9
⁄16 DIA.
4 ORIFICIOS
DRAIN PLUG ADAPTER ½
TAPÓN DE FOOT, BASE J
N 3½ 3½ ADAPTADORA
DRENAJE L 6½ 1
M
8½ 8½
ADAPTER FOOT
BASE ADAPTADORA
NOTE: NOTA:
1. All pumps shipped in vertical 1. Todas las bombas se embarcan con
discharge position. For other orien- la descarga en posición vertical. Para
tations, remove casing bolts, rotate otras orientaciones, retire los pernos
to desired position, and tighten de la carcasa, haga rotar la descarga
3
⁄8 - 16 casing bolts to 37 ft./lbs. hasta la posición deseada y ajuste
torque., ½ - 13 casing bolts to 90 los 16 pernos de 3/8 de pulgada a
ft./lbs. torque. una torsión de 37 pies/libra, y los 13
2. Dimensions in inches, weight in pernos de 1/2 pulgada a 90 pies/libra.
pounds. 2. Dimensiones en pulgadas, peso
3. Not to be used for construction en libras.
purposes. 3. No utilizar con fines de construc-
ción.
GOULDS PUMPS 37
Commercial Water
Engineering Data – M-Group Mechanical Seal
Datos de ingeniería – Grupo M Sello mecánico
Channel Steel Bedplate. Clockwise rotation viewed from drive end.
Placa de asiento de acero acanalado. Rotación dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
CP 3¾ C MAX.
SPACER COUPLING, ACOPLAMIENTO ESPACIADOR
Z R DISCHARGE COUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
AB MAX. Y W 37⁄8
DESCARGA
1.625 DIA.
1.624 SINGLE PHASE ONLY
MONOFÁSICO SOLAMENTE
X SUCTION
SUCCIÓN
P
MAX.
DC DD (4) HOLES
* MAX.
5
⁄8 DIA.
KEYWAY ⁄16 x ⁄8
3 3
HD CHAVETERO 3⁄16 x 3⁄8 4 ORIFICIOS
HG
NPT DRAIN
HE HE DRENAJE NPT L HF 1¾
HA HB
* Dimension will include any special shims required to match pump centerline to motor.
* La dimensión incluye cualquier cuña especial que se requiera para hacer coincidir la línea central NOTE:
de la bomba con el motor. 1. All pumps shipped in vertical dis-
charge position. For other orientations,
Pump Dimensions and Weights remove casing bolts, rotate to desired
Peso y dimensiones de la bomba position, and tighten 3⁄8 - 16 casing bolts
to 37 ft./lbs. torque., ½ - 13 casing bolts
NPT Weight
to 90 ft./lbs. torque.
Pump Suction Discharge CP DC Drain (lbs)
DD L R W X Y Z 2. Dimensions in inches, weight in
Bomba Succión Descarga Max. Max. Drenaje Pesos
NPT (libras) pounds.
1½ x 2 –10 2* 1½* 217⁄8 6¾ 57⁄8 93⁄8 1¼ 5 3 5½ 155 3. Not to be used for construction
1¼ 6 purposes.
2½ x 3 – 8 3* 2½* 223⁄8 6¼ 5¼ 97⁄8 113⁄16 51⁄8 33⁄8 5 140
2½ x 3 – 9
215⁄8 71⁄8 6 91⁄8 7½ 2¾ 5½ 147 NOTA: 1. Todas las bombas se embarcan
2½ x 3 – 10 3 2½ 3½ 3
⁄8 5
con la descarga en posición vertical. Para
2½ x 3 – 13 21 ⁄8 8 ⁄8 7 ⁄8 9 ⁄8
7 7 5 3
9 3 7½ 201
3 x 4 – 8 223⁄16 6¼ 53⁄8 97⁄16 ¼ 55⁄16 7 55⁄8 144 otras orientaciones, retire los pernos de la
3 x 4 – 10 4 3 22 7 3⁄8 6½ 9½ 3¾ 51⁄8 7½ 5½ 161 carcasa, haga rotar la descarga hasta la po-
3
3 x 4 – 13 217⁄8 9½ 81⁄8 93⁄8 5 9 7½ 217 sición deseada y ajuste los 16 pernos de 3⁄8
4 x 5 – 8 5 223⁄8 67⁄8 5¾ 97⁄8 3
⁄8 5½ 8 5 161 de pulgada a una torsión de 37 pies/libra, y
4 x 6 – 10 4 22½ 85⁄8 7½ 10 4½ 5½ 8½ 31⁄8 7 200 los 13 pernos de 1/2 pulgada a 90 pies/libra.
6
4 x 6 – 13 221⁄8 9¾ 81⁄8 95⁄8 5¼ 9 3 7½ 233 2. Dimensiones en pulgadas, peso en
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges. libras.
* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150. 3. No utilizar con fines de construcción.
Motor and Bedplate Dimensions and Weights (may vary with manufacturer.)
Peso y dimensiones del motor y la placa de asiento (pueden variar de acuerdo al fabricante)
Motor HP @ 1750 RPM - T- Bedplate Data, Datos de la placa de asiento
HP @ 3500 RPM Frame Only, Bastidor Wt.
Frame AB C P Weight Motor Bearing Frame
T únicamente (lbs.)
Bastidor Max. Max. Max. Pesos HA HB HD HE HF HG (lbs) Shim Shim, Cuña del
del Three phase, Trifásico Pesos Cuña del bastidor de
(libras) (libras)
motor ODP TEFC ODP TEFC motor cojinetes
184T — —
5 5 57⁄8 18 8 95 13⁄4 —
213T — —
7 ⁄2
1
7 ⁄2
1
18 5 116
73⁄8 9 ⁄8 1 —
215T 15 —
10 10 191⁄8 136 13 42 101⁄4 51⁄4 381⁄2 4 111
254T 20 15 15 15 1 21 ⁄8
5
266
10 ⁄8 13 — —
256T 25 20 20 20 233⁄8 264
284TS/T 30 25 25 25 5 24 ⁄8
7
392
12 ⁄8 15 15 44 101⁄2 53⁄4 401⁄2 31⁄2 124 — 3
⁄4
286TS/T 40 30 30 30 265⁄8 422
324TS/T 50 40 40 40 1 28 ⁄4 3
3
592
14 ⁄8 17 ⁄8 12 — 13⁄4
326TS/T 60 50 50 50 301⁄4 634
18 48 71
⁄4 44 ⁄2 4
1
183
364TS/T 75 60 60 60 1 315⁄8 7 834
15 ⁄8 18 ⁄8 13 — 23⁄4
356TS/T 100 75 75 75 325⁄8 1000
GOULDS PUMPS 38
Commercial Water
Engineering Data – M-Group Packed Box
Datos de ingeniería – Grupo M Caja prensaestopas
Channel Steel Bedplate. Clockwise rotation viewed from drive end.
Placa de asiento de acero acanalado. Rotación dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
CP 3¾ C MAX.
SPACER COUPLING, ACOPLAMIENTO ESPACIADOR
Z R DISCHARGE COUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
AB MAX. Y W 3 ⁄8
7
DESCARGA
1.625 DIA.
1.624 SINGLE PHASE ONLY
MONOFÁSICO SOLAMENTE
X SUCTION
SUCCIÓN
P
MAX.
DC DD (4) HOLES
* MAX. 5
⁄8 DIA.
KEYWAY 3⁄16 x 3⁄8
HD CHAVETERO 3⁄16 x 3⁄8 4 ORIFICIOS
HG
NPT DRAIN
HE HE DRENAJE NPT L HF 1¾
HA HB
* Dimension will include any special shims required to match pump centerline to motor.
NOTE:
* La dimensión incluye cualquier cuña especial que se requiera para hacer coincidir la línea central
de la bomba con el motor. 1. All pumps shipped in vertical dis-
charge position. For other orientations,
Pump Dimensions and Weights remove casing bolts, rotate to desired
Peso y dimensiones de la bomba position, and tighten 3⁄8 - 16 casing bolts
to 37 ft./lbs. torque., ½ - 13 casing bolts
NPT Weight to 90 ft./lbs. torque.
Pump Suction Discharge CP DC Drain (lbs)
Bomba Succión Descarga Max. Max. DD L
R W
Drenaje X Y Z Pesos 2. Dimensions in inches, weight in
NPT (libras) pounds.
1½ x 2 –10 2* 1½* 24¾ 6¾ 57⁄8 12¼ 1¼ 77⁄8 3 5½ 165 3. Not to be used for construction
¼ 6 purposes.
2½ x 3 – 8 3* 2½* 25¼ 6¼ 5¼ 12¾ 113⁄16 8 33⁄8 5 150
2½ x 3 – 9
2½ x 3 – 10 3 2½
24½ 71⁄8 6 12
3½ 3
⁄8 77⁄8
7½ 2¾ 5½ 160 NOTA: 1. Todas las bombas se embarcan
con la descarga en posición vertical. Para
2½ x 3 – 13 24¾ 87⁄8 75⁄8 12¼
9 3 7½ 215
3 x 4 – 8 221⁄16 6¼ 53⁄8 125⁄16 ¼ 83⁄16 7 55⁄8 155 otras orientaciones, retire los pernos de la
4 3 carcasa, haga rotar la descarga hasta la po-
3 x 4 – 10 247⁄8 7 3⁄8 6½ 123⁄8 3¾ 8 7½ 5½ 170
3
3 x 4 – 13 24¾ 9½ 8 ⁄8 12¼
1
77⁄8 9 7½ 230 sición deseada y ajuste los 16 pernos de 3⁄8
4 x 5 – 8 5 25¼ 67⁄8 5¾ 12¾ 3
⁄8 8 5 170 de pulgada a una torsión de 37 pies/libra, y
8 ⁄8
3
4 x 6 – 10
6
4 253⁄8 85⁄8 7½ 127⁄8 4½ 8½ 31⁄8 7 210 los 13 pernos de 1/2 pulgada a 90 pies/libra.
4 x 6 – 13 25 9¾ 81⁄8 12½ 81⁄8 9 3 7½ 245 2. Dimensiones en pulgadas, peso en
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges. libras.
* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150. 3. No utilizar con fines de construcción
Motor and Bedplate Dimensions and Weights (may vary with manufacturer.)
Peso y dimensiones del motor y la placa de asiento (pueden variar de acuerdo al fabricante)
Motor HP @ 1750 RPM - T- Bedplate Data, Datos de la placa de asiento
HP @ 3500 RPM Frame Only, Bastidor Wt.
Frame Weight Motor Bearing Frame
T únicamente AB C P (lbs.)
Bastidor (lbs) Shim Shim, Cuña del
Three phase, Trifásico Max. Max. Max. Pesos HA HB HD HE HF HG Pesos
del Cuña del bastidor de
(libras) cojinetes
motor ODP TEFC ODP TEFC (libras) motor
184T — —
5 5 57⁄8 18 8 95 13⁄4 —
213T — —
7 ⁄2
1
7 ⁄2
1
18 5 116
73⁄8 9 ⁄8 1 —
215T 15 —
10 10 191⁄8 136 13 42 101⁄4 51⁄4 381⁄2 4 111
254T 20 15 15 15 1 21 ⁄8
5
266
10 ⁄8 13 — —
256T 25 20 20 20 233⁄8 264
284TS/T 30 25 25 25 5 24 ⁄8
7
392
12 ⁄8 15 15 44 101⁄2 53⁄4 401⁄2 31⁄2 124 — 3
⁄4
286TS/T 40 30 30 30 265⁄8 422
324TS/T 50 40 40 40 1 28 ⁄4 3
3
592
14 ⁄8 17 ⁄8 12 — 13⁄4
326TS/T 60 50 50 50 301⁄4 634
18 48 71
⁄4 44 ⁄2 4
1
183
364TS/T 75 60 60 60 1 315⁄8 7 834
15 ⁄8 18 ⁄8 13 — 23⁄4
356TS/T 100 75 75 75 325⁄8 1000
GOULDS PUMPS 39
Commercial Water
Engineering Data – L-Group Mechanical Seal & Packed Box
Datos de ingeniería – Grupo L Sello Mecánico & Caja prensaestopas
Channel Steel Bedplate. Clockwise rotation viewed from drive end.
Placa de asiento de acero acanalado. Rotación dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
CP 3¾ C REF.
SPACER COUPLING, ACOPLAMIENTO ESPACIADOR
AB REF. Z R DISCHARGE COUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
Y W 3 ⁄87
DESCARGA
1.625 DIA.
1.624 SINGLE PHASE ONLY
MONOFÁSICO SOLAMENTE
X SUCTION
SUCCIÓN
P
REF.
DC DD
MAX. KEYWAY 3⁄16 x 3⁄8
HD ¾“ DIA.
CHAVETERO 3⁄16 x 3⁄8 4-PLACES
6 ▼
NPT DRAIN ▼
HE HE DRENAJE NPT L HF 2 ⁄8
1
3
⁄8
HA HB
GOULDS PUMPS 40
Commercial Water
3756 M & L-Group SAE Drive Dimensions and Weights Packed Box
Dimensiones y pesos del mando SAE Grupo L y 3756 M Caja prensaestopas
CP
Z R DISCHARGE Y W V1 V2
DESCARGA
X
1.625 DIA.
SUCTION 1.624
SUCCIÓN
KEYWAY
3
⁄16 x 3⁄8
DD CHAVETERO
3
⁄16 x 3⁄8
K DC
MAX.
SAE #1 – 5
N N NPT DRAIN
2 HOLES DRENAJE NPT J SAE drive number is determined by
.56 DIA. M
the engine flywheel housing size.
2 ORIFICIOS
El número del mando SAE se determina
por el tamaño de la caja del volante
Dimensions and Weights del motor.
Pesos y dimensiones
NPT Drain Weight (lbs.)
Pump Suction Discharge DC
CP DD J K M N R Drenaje W X Y Z Pesos
Bomba Succión Descarga (Max.)
NPT (libras)
1½ x 2 –10 2* 1½* 257⁄16 6¾ 57⁄8 — — — — 1¼ 77⁄8 6 3 5½ 235
¼
2½ x 3 – 8 3* 2½* 2515⁄16 6¼ 5¼ — — — — 113⁄16
8
33⁄8 5 220
2½ x 3 – 9
25 ⁄16 7 ⁄8
3 1
6 — — — —
7½ 2¾ 5½ 230
2½ x 3 – 10 3 2½
3½ 3
⁄8 77⁄8
2½ x 3 – 13 25 ⁄16 8 ⁄8
5 7
7 ⁄8 —
5
— — — 9 3 7½ 285
3 x 4 – 8
22¾ 6¼ 53⁄8 — — — —
¼ 83⁄16 7 55⁄8 225
3 x 4 – 10 4 3 259⁄16 73⁄8 6½ — — — — 3¾ 8 7½ 5½ 240
3
3 x 4 – 13
257⁄16 9½ 81⁄8 — — — —
77⁄8 9
7½ 300
4 x 5 – 8 5
2513⁄16 67⁄8 5¾ — — — —
83⁄8 8 5 240
4 x 6 – 10 271⁄16 85⁄8 7½ — — — — 83⁄8 8½ 31⁄8 7 280
4 4½
⁄
3
8
4 x 6 – 13 6 2511⁄16 9¾ 81⁄8 — — — —
81⁄8 9 3 7½ 315
■ 4 X 6 – 16 273⁄16 12¾ 11 115⁄16 9¾ 16 7 85⁄8 12 4 10½ 500
■ 6 X 8 – 13 8 6 2515⁄16 12¾ 10½ 23⁄8 7½ 13 5½ 5½ 83⁄8 11 37⁄8 8¾ 400
■ 8 x 10 – 13 10 8 27 ⁄16 14¾
3
13 2 ⁄8
3
7½ 13 5½ 6¾ 8 ⁄8 12¾
5
4 10 585
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges. SAE # V1 V2
Dimensions in inches, weights in lbs. Do not use for construction purposes. 1, 3, 5 13¼ 1½
* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.
2, 4 13 1¾
Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.
■ Indicates “L” Group pump., ■ Indica una bomba Grupo “L”.
NOTE: NOTA:
1. All pumps shipped in horizontal 1. Todas las bombas se embarcan con
discharge position. For other la descarga en posición horizontal.
orientations, remove casing bolts, Para otras orientaciones, retire los
rotate to desired position, and pernos de la carcasa, haga rotar la
tighten 3⁄8 - 16 casing bolts to 37 descarga hasta la posición deseada y
ft./lbs. torque., ½ - 13 casing bolts ajuste los 16 pernos de 3/8 de pulgada
to 90 ft./lbs. torque. a una torsión de 37 pies/libra, y los 13
2. Dimensions in inches, weight pernos de 1/2 pulgada a 90 pies/libra.
in pounds. 2. Dimensiones en pulgadas, peso en
3. Not to be used for construction libras.
purposes. 3. No utilizar con fines de construc-
ción.
GOULDS PUMPS 41
Commercial Water
3756 M & L-Group SAE Drive Dimensions and Weights Mechanical Seal
Dimensiones y pesos del mando SAE Grupo L y 3756 M Sello Mecánico
CP
Z R DISCHARGE Y W V1 V2
DESCARGA
X
1.625 DIA.
SUCTION 1.624
SUCCIÓN
KEYWAY
3
⁄16 x 3⁄8
DD CHAVETERO
3
⁄16 x 3⁄8
K DC
MAX.
SAE #1 – 5
N N NPT DRAIN
2 HOLES DRENAJE NPT J SAE drive number is determined by
.56 DIA. M
the engine flywheel housing size.
2 ORIFICIOS
El número del mando SAE se determina
por el tamaño de la caja del volante
Dimensions and Weights del motor.
Pesos y dimensiones
NPT Drain Weight (lbs.)
Pump Suction Discharge DC
CP DD J K M N R Drenaje W X Y Z Pesos
Bomba Succión Descarga (Max.)
NPT (libras)
1½ x 2 –10 2* 1½* 229⁄16 6¾ 57⁄8 — — — — 1¼ 5 6 3 5½ 235
¼
2½ x 3 – 8 3* 2½* 231⁄16 6¼ 5¼ — — — — 113⁄16
51⁄8
33⁄8 5 220
2½ x 3 – 9
22 ⁄16 7 ⁄8
5 1
6 — — — —
7½ 2¾ 5½ 230
2½ x 3 – 10 3 2½
3½ 3
⁄8 5
2½ x 3 – 13 22 ⁄16 8 ⁄8
7 7
7 ⁄8 —
5
— — — 9 3 7½ 285
3 x 4 – 8
197⁄8 6¼ 53⁄8 — — — —
¼ 55⁄16 7 55⁄8 225
3 x 4 – 10 4 3 2211⁄16 73⁄8 6½ — — — — 3¾ 51⁄8 7½ 5½ 240
3
3 x 4 – 13
229⁄16 9½ 81⁄8 — — — —
5 9
7½ 300
4 x 5 – 8 5
2215⁄16 67⁄8 5¾ — — — —
5½ 8 5 240
4 x 6 – 10 245⁄16 85⁄8 7½ — — — — 5½ 8½ 31⁄8 7 280
4 4½
⁄
3
8
4 x 6 – 13 6 2213⁄16 9¾ 81⁄8 — — — —
5¼ 9 3 7½ 315
■ 4 x 6 – 16 273⁄16 12¾ 11 17⁄8 9¾ 16 7 85⁄8 12 4 10½ 500
■ 6 x 8 – 13 8 6 2515⁄16 12¾ 10½ 23⁄8 7½ 13 5½ 5½ 83⁄8 11 37⁄8 8¾ 400
■ 8 x 10 – 13 10 8 273⁄16 14¾ 13 23⁄8 7½ 13 5½ 6¾ 85⁄8 12¾ 4 10 585
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges. SAE # V1 V2
Dimensions in inches, weights in lbs. Do not use for construction purposes.
1, 3, 5 13¼ 1½
* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.
Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción. 2, 4 13 1¾
■ Indicates “L” Group pump., ■ Indica una bomba Grupo “L”.
NOTE: NOTA:
1. All pumps shipped in horizontal 1. Todas las bombas se embarcan con
discharge position. For other la descarga en posición horizontal.
orientations, remove casing bolts, Para otras orientaciones, retire los
rotate to desired position, and pernos de la carcasa, haga rotar la
tighten 3⁄8 - 16 casing bolts to 37 descarga hasta la posición deseada y
ft./lbs. torque., ½ - 13 casing bolts ajuste los 16 pernos de 3/8 de pulgada
to 90 ft./lbs. torque. a una torsión de 37 pies/libra, y los 13
2. Dimensions in inches, weight pernos de 1/2 pulgada a 90 pies/libra.
in pounds. 2. Dimensiones en pulgadas, peso en
3. Not to be used for construction libras.
purposes. 3. No utilizar con fines de construc-
ción.
GOULDS PUMPS 42
Commercial Water
Specifications Especificaciones Typical Applications Aplicaciones típicas
GOULDS PUMPS 43
Commercial Water
IT T Commercial Water
Goulds Pumps and the ITT Engineered Blocks Symbol are registered trademarks and tradenames of ITT Corporation.
Goulds Pumps y el símbolo ITT Engineered Blocks son marcas registradas y marcas comerciales de ITT Corporation.
Teflon is a registered trademark of Dupont. Teflon es una marca registrada de Dupont.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. LAS ESPECIFICACIONES ESTÁN SUJETAS A CAMBIO SIN PREVIO AVISO.
36/3756M March (Marzo), 2008
© 2008 ITT Corporation