Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Harmsen
aci perú
Reglamento de Concreto
Norma IBC-2000
Parte 1/3
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
ASUNTO : IBC-2000
REFERENCIA : REGLAMENTO DE CONCRETO
HECHO POR : ING. TEODORO E. HARMSEN
FECHA : ENERO DEL 2001
INTRODUCCIÓN
El borrador de este código fue comentado por todas las partes interesadas (usuarios,
industriales, autoridades, etc.) y hubo un forum público en 1992, una audiencia pública
en 1998 y dos en 1999 antes de su adopción.
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
En el capítulo 19.- Concreto, se sigue en términos generales el código ACI 318-99. Allí se
nombra, por ejemplo, como artículo 1905.6.1 al artículo 5.6.1 del ACI, su equivalente. A
muchos artículos del ACI les ha puesto títulos lo que aclara mucho el código.
A. Materiales y pruebas.- Cumplirán con el artículo 3.8 del ACI 318-99 pero cuando
se requiera pruebas o inspecciones especiales, deberán hacerse de acuerdo al
capítulo 17 del IBC. No se requiere inspecciones especiales para lo siguiente:
2.3 Cuando el diseño de la zapata está basado en f’c < 175 Kg/cm²
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
TABLE 1805.5(1)
a,b,c
PLAIN MASONRY AND PLAIN CONCRETE FOUNDATION WALLS
PLAIN MASONRY
MINIMUM NOMINAL WALL THICKNESS (inches)
a
Soil classes and lateral soil load (psf per foot below natural grade)
WALL HEIGHT HEIGHT OF UNBALANCED GW, GP, SW and SP Soils GM, GC, SM, SM-SC and ML Soils SC, MH, ML-CL and Inorganic CL Soils
(feet) BACKFILL (feet) 30 45 60
4 (or less) 8 8 8
5 8 10 10
c
7 6 10 12 10 (solid )
c c
7 12 10 (solid ) 10 (solid )
4 (or less) 8 8 8
5 8 10 12
c
8 6 10 12 12 (solid )
c
7 12 12 (solid ) Note d-
b c
8 10 (solid ) 12 (solid ) Note d
4 (or less) 8 8 8
5 8 10 12
c
9 6 12 12 12 (solid )
c c
7 12 (solid ) 12 (solid ) Note d
c
8 12 (solid ) Note d Note d
9 Note d Note d Note d
PLAIN CONCRETE
MINIMUM NOMINAL WALL THICKNESS (inches)
a
Soil classes and lateral soil load (psf per foot below natural grade)
WALL HEIGHT HEIGHT OF UNBALANCED GW, GP, SW and SP Soils GM, GC, SM, SM-SC and ML Soils SC, MH, ML-CL and Inorganic CL Soils
(feet) BACKFILL (feet) 30 45 60
4 (or less) 7 1/2 7 1/2 7 1/2
5 7 1/2 7 1/2 7 1/2
7 6 7 1/2 7 1/2 8
7 7 1/2 8 10
4 (or less) 7 1/2 7 1/2 7 1/2
5 7 1/2 7 1/2 7 1/2
8 6 7 1/2 7 1/2 10
7 7 1/2 10 10
8 10 10 12
4 (or less) 7 1/2 7 1/2 7 1/2
5 7 1/2 7 1/2 7 1/2
9 6 7 1/2 7 1/2 10
7 7 1/2 10 10
8 10 10 12
9 10 12 Note e
For SI: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1 pound per square foot per foot = 0.157 kPa/m.
a. For design lateral soil loads, see Section 1610. Soil classes are in accordance with the Unified Soil Classification System and design lateral soil loads are
for moist soil conditions without hydrostatic pressure.
b. Provisions for this table are based on construction requirements specified in Section 1805.5.2.
c. Solid grouted hollow units or solid masonry units.
d. A design in compliance with Chapter 21 or reinforcement in accordance with Table 1805.5(2) is required.
e. A design in compliance with Chapter 19 is required.
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
TABLE 1805.5(2)
a, b, c
8-INCH REINFORCED CONCRETE AND MASONRY FOUNDATION WALLS WHERE d > 5 INCHES
VERTICAL REINFORCEMENT
a
Soil classes and lateral soil load (psf per foot below natural grade)
WALL HEIGHT HEIGHT OF UNBALANCED GW, GP, SW and SP Soils GM, GC, SM, SM-SC and ML Soils SC, MH, ML-CL and Inorganic CL Soils
(feet) BACKFILL (feet) 30 45 60
4 (or less) #4 at 48" o.c. #4 at 48" o.c. #4 at 48" o.c.
5 #4 at 48" o.c. #4 at 48" o.c. #4 at 40" o.c.
7 6 #4 at 48" o.c. #5 at 48" o.c. #5 at 40" o.c.
7 #4 at 40" o.c. #5 at 40" o.c. #6 at 48" o.c.
4 (or less) #4 at 48" o.c. #4 at 48" o.c. #4 at 48" o.c.
5 #4 at 48" o.c. #4 at 48" o.c. #4 at 40" o.c.
8 6 #4 at 48" o.c. #5 at 48" o.c. #5 at 40" o.c.
7 #5 at 48" o.c. #6 at 48" o.c. #6 at 40" o.c.
8 #5 at 40" o.c. #6 at 40" o.c. #7 at 40" o.c.
4 (or less) #4 at 48" o.c. #4 at 48" o.c. #4 at 48" o.c.
5 #4 at 48" o.c. #4 at 48" o.c. #5 at 48" o.c.
9 6 #4 at 48" o.c. #5 at 48" o.c. #6 at 48" o.c.
7 #5 at 48" o.c. #6 at 48" o.c. #7 at 48" o.c.
8 #5 at 40" o.c. #7 at 48" o.c. #8 at 48" o.c.
9 #6 at 40" o.c. #8 at 48" o.c. #8 at 32" o.c.
For SI: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1 pound per square foot per foot = 0.157 kPa/m.
a. For design lateral soil loads, see Section 1610. Soil classes are in accordance w ith the Unified Soil Classification System and design lateral soil loads are
for moist soil conditions w ithout hydrostatic pressure.
b. Provisions for this table are based on construction requirements specified in Section 1805.5.2.
c. For alternative reinforcement, see Section 1805.5.3.
TABLE 1805.5(3)
a, b, c
10-INCH REINFORCED CONCRETE AND MASONRY FOUNDATION WALLS WHERE d > 6.75 INCHES
VERTICAL REINFORCEMENT
a
Soil classes and lateral soil load (psf per foot below natural grade)
WALL HEIGHT HEIGHT OF UNBALANCED GW, GP, SW and SP Soils GM, GC, SM, SM-SC and ML Soils SC, MH, ML-CL and Inorganic CL Soils
(feet) BACKFILL (feet) 30 45 60
4 (or less) #4 at 56" o.c. #4 at 56" o.c. #4 at 56" o.c.
5 #4 at 56" o.c. #4 at 56" o.c. #4 at 56" o.c.
7 6 #4 at 56" o.c. #4 at 48" o.c. #4 at 40" o.c.
7 #4 at 56" o.c. #5 at 56" o.c. #5 at 40" o.c.
4 (or less) #4 at 56" o.c. #4 at 56" o.c. #4 at 56" o.c.
5 #4 at 56" o.c. #4 at 56" o.c. #4 at 48" o.c.
8 6 #4 at 56" o.c. #4 at 48" o.c. #5 at 56" o.c.
7 #4 at 48" o.c. #4 at 32" o.c. #6 at 56" o.c.
8 #5 at 56" o.c. #5 at 40" o.c. #7 at 56" o.c.
4 (or less) #4 at 56" o.c. #4 at 56" o.c. #4 at 56" o.c.
5 #4 at 56" o.c. #4 at 56" o.c. #4 at 48" o.c.
9 6 #4 at 56" o.c. #4 at 40" o.c. #4 at 32" o.c.
7 #4 at 40" o.c. #5 at 48" o.c. #6 at 48" o.c.
8 #4 at 32" o.c. #6 at 48" o.c. #4 at 16" o.c.
9 #5 at 40" o.c. #6 at 40" o.c. #7 at 40" o.c.
For SI: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1 pound per square foot per foot = 0.157 kPa/m.
a. For design lateral soil loads, see Section 1610. Soil classes are in accordance w ith the Unified Soil Classification System and design lateral soil loads are
for moist soil conditions w ithout hydrostatic pressure.
b. Provisions for this table are based on construction requirements specified in Section 1805.5.2.
c. For alternative reinforcement, see Section 1805.5.3.
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
TABLE 1805.5(4)
a, b, c
12-INCH REINFORCED CONCRETE AND MASONRY FOUNDATION WALLS WHERE d > 8.75 INCH
VERTICAL REINFORCEMENT
a
Soil classes and lateral soil load (psf per foot below natural grade)
WALL HEIGHT HEIGHT OF UNBALANCED GW, GP, SW and SP Soils GM, GC, SM, SM-SC and ML Soils SC, MH, ML-CL and Inorganic CL Soils
(feet) BACKFILL (feet) 30 45 60
4 (or less) #4 at 72" o.c. #4 at 72" o.c. #4 at 72" o.c.
5 #4 at 72" o.c. #4 at 72" o.c. #4 at 72" o.c.
7 6 #4 at 72" o.c. #4 at 64" o.c. #4 at 48" o.c.
7 #4 at 72" o.c. #4 at 48" o.c. #5 at 56" o.c.
4 (or less) #4 at 72" o.c. #4 at 72" o.c. #4 at 72" o.c.
5 #4 at 72" o.c. #4 at 72" o.c. #4 at 72" o.c.
8 6 #4 at 72" o.c. #4 at 56" o.c. #5 at 72" o.c.
7 #4 at 64" o.c. #5 at 64" o.c. #4 at 32" o.c.
8 #4 at 48" o.c. #4 at 32" o.c. #5 at 40" o.c.
4 (or less) #4 at 72" o.c. #4 at 72" o.c. #4 at 72" o.c.
5 #4 at 72" o.c. #4 at 72" o.c. #4 at 64" o.c.
9 6 #4 at 72" o.c. #4 at 56" o.c. #5 at 64" o.c.
7 #4 at 56" o.c. #4 at 40" o.c. #6 at 64" o.c.
8 #4 at 64" o.c. #6 at 64" o.c. #6 at 48" o.c.
9 #5 at 56" o.c. #7 at 72" o.c. #6 at 40" o.c.
For SI: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1 pound per square foot per foot = 0.157 kPa/m.
a. For design lateral soil loads, see Section 1610. Soil classes are in accordance w ith the Unified Soil Classification System and design lateral soil loads are
for moist soil conditions without hydrostatic pressure.
b. Provisions for this table are based on construction requirements specified in Section 1805.5.2.
c. For alternative reinforcement, see Section 1805.5.3.
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
TABLE 1704.4
REQUIRED VERIFICATION AND INSPECTION OF CONCRETE CONSTRUCTION
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
TABLE 1704.3
REQUIRED VERIFICATION AND INSPECTION OF STEEL CONSTRUCTION
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe
ACI-Perú / Reglamento de Concreto IBC-2000 / T. Harmsen
www.aci-peru.org.pe / aci-peru@amauta.rcp.net.pe