Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Aspiradora arrastre
2.2:
• Regule el tubo telescópico al largo que desea.
3. Retire objetos grandes o cortantes del piso antes • Deslice hacia adelante el botón regulador y tire
de pasar la aspiradora para evitar que se pueda hacia afuera la parte inferior del tubo de acuerdo
dañar. al largo que desea. Luego, simplemente deslice el
botón y déjelo encajar en la posición correcta.
Aspirado
1. Antes de usar la aspiradora, desenrolle una
cantidad suficiente de cable eléctrico y enchúfelo
a un tomacorriente. La marca amarilla del cable
eléctrico indica el largo máximo – no se debe exceder.
Para encender la aspiradora, presione el botón de
pedal que está en la carcasa de la aspiradora
NOTE: Turn off vacuum and unplug the electrical The HEPA filter and the HEPA cover should be
cord before changing dust bag or cleaning motor cleaned regularly. Cleaning is best done when
filter. Never operate the vacuum cleaner without emptying the dust container. To do this follow the
the dust bag or filter. instructions in the Emptying dust container section.
1. Turn off and unplug cleaner. 1. Switch off the vacuum cleaner and disconnect the
2. Open bag cover by pushing latch up with fingers plug from the mains. To do this always pull on the
and lifting bag cover. plug and not on the cable.
3. Remove motor filter and clean by rinsing under 2. You can pull the dust container together with the
warm water, if heavily soiled. Let completely air dry cleaning system out of their anchoring with the aid
before reinstalling. of the carrier handle on the dust container. Take
4. Open bag folds slightly. hold of the carrier handle on the dust container and
5. Place dust bag in dust bag frame by pushing pull it upwards. Now pull the dust container out and
cardboard collar into ledge loosen the HEPA cover and HEPA filter out of the
on dust bag frame until collar snaps into position. dust container with the aid of the lateral unlocking
6. Place dust bag frame inside dust bag button.
compartment placing dust bag frame into the 3.Turn the dust container cover carefully until it is
guides at the very front of released and the
the dust bag compartment. HEPA filter will come away easily
7. Swing bag cover lid closed and push to latch. 4. Now rinse the HEPA filter under running water and
allow it to dry.
5. Place the HEPA filter back in the HEPA cover
(or replace with a new one) and fit it into the dust
container.
Then fit the dust container back into position in the
cyclone dust container until it snaps into place. Your
cyclone vacuum cleaner is now ready for use again.
The exhaust air filter cleans the air a final time before
it leaves
the vacuum cleaner. You can clean the exhaust air
filter as follows:
1. Switch off the vacuum cleaner and disconnect the
plug from
the mains. To do this always pull on the plug and not
on the cable.
Regulating the suction power 2. Open the exhaust air grill (this is at the rear of the
cyclone vacuum cleaner.)
You can set the suction power on the device 3. The exhaust air filter is visible when the grill has
individually as you require it using the suction been opened.
regulator. We recommend using minimum suction 4. Rinse the filter under cold running water and allow
power for delicate materials. dry.
Select medium suction power for mattresses, 5. Put the exhaust air filter back into place (or replace
upholstered furniture and carpets. Select maximum with a new one) and place in the grill.
suction power for tiled, wood and other robust 6. Close the exhaust air filter grill.
floors.
URSUS TROTTER SMALL APPLIANCES S.A.
Una empresa Chilena con precisión Alemana que da confianza
San Pablo 3770- Tel.:28383000 - Fax.: 28383005
Casilla 3234- Santiago - Chile
ventas@ursustrotter.cl - www.ursustrotter.cl
Sujeto a alteración sin previo aviso.
ursustrotter.cl