Documentos de Académico
Documentos de Profesional
Documentos de Cultura
WWW.COMPRABASCULA.COM
1
Manual de usuario
Manuel dusager
Users guide
Declaracin de conformidad
Dclaration de conformit
Declaration of conformity 15
2
Modelo Super SS Balanza solo peso Manual de usuario
ENG FR ESP
Gracias por utilizar nuestra balanza de la serie SUPER SS de doble lado y protegida contra la humedad y el
agua. La balanza SUPER SS es una balanza de acero inoxidable. La balanza incluye avances de altas tc-
nicas de ordenador-control. Incluye una alta precisin en el pesado, con facilidades de transporte y un precio
bajo.
Es resistente y de larga duracin. Puede ser utilizada en almacenes para pesar diferentes paquetes de pro-
ductos, as como en lugares con humedad alta gracias a su alta proteccin contra la humedad.
Botn tara.
Apaga la balanza.
3
Manual de usuario Balanza solo peso Modelo Super SS
ENG FR ESP
2.2. MENSAJES DE PANTALLA
3. GUA DE OPERACIONES
3.1. PREPARACIN
Ajuste los pies de la base, vigile el nivel, situe la bandeja horizontalmente.
3.2.2. Apagar:
Presione durante unos segundos el botn OFF.
3.3. CERO
Cuando sin tara el peso mostrado en la pantalla es 4% de la capacidad mxima, presione el botn ON/
ZERO, la pantalla mostrar 0, el LED de ZERO se encender.
3.4. PESADO
Situe el peso en la bandeja.
4
Modelo Super SS Balanza solo peso Manual de usuario
ENG FR ESP
3.8. CARGA
Potencia suministrada por una batera interna recargable de cido de plomo de 6V/4Ah. Cuando muestre
-BAtLo- por favor, apague y cargue la batera inmediatamente. El tiempo de recarga completa es de 12
horas.
5
Manual de usuario Balanza solo peso Modelo Super SS
ENG FR ESP
3.9.6 bUZZEr (ja el sonido de la alarma)
Cuando el men muestra bUZZEr, presione TARE para entrar, presione SET/0~9 para elegir on o oFF,
presione TARE para conrmar.
4. NOTAS
1. Debe cargar la batera como mnimo cada 3 meses cuando usted no utilice la balanza durante un perodo
largo de tiempo. La carga durar unas 12 horas.
2. No sobrecargue la balanza. No tire violentamente objetos pesados sobre la balanza. El dao por
sobrepeso no se encuentra dentro del rango de garanta de mantenimiento.
3. No utilice objetos alados para manejar el teclado. Si la goma est daada, ello afectar la garanta
contra agua y humedad de la balanza.
4. Mantenga la balanza limpia para asegurar un pesado correcto.
5. Hay un precinto de plomo en la parte inferior de la balanza. Los usuarios no deben quitar este precinto. Si
se daa el precinto no se garantiza el correcto mantenimiento de la balanza.
5. CAMBIO DE DIVISIN
1. Pulse ON/ZERO para encender la balanza.
2. Presione la tecla TARE hasta que aparezca la divisin deseada (nXXXX). Al volver a presionar TARE
regresa a la divisin anterior. La divisin que aparece en pantalla es la divisin seleccionada.
3. La balanza regresa automticamente al modo de pesaje.
6. CALIBRACIN
Esta operacin slo puede realizarla el personal autorizado competente por las leyes de cada pas.
1. Con la balanza apagada, desprecintar el precinto del interruptor de modicacin de divisin situado en la
cara inferior de la balanza.
2. Cambiar la posicin del interruptor de modiciacin de divisin.
3. Pulse el botn ON/ZERO para encender la balanza.
4. Presione la tecla TARE hasta que apareza CAL en la pantalla.
5. Pulse la tecla TARE nuevamente, aparezer la capacidad mxima de la balanza.
6. Situe sobre la balanza el peso de su capacidad mxima.
7. Espere 5 segundos.
8. Pulse la tecla TARE nuevamente, aparecer el mensaje CaEnd en la pantalla. La calibracin ha
terminado y la balanza regresa automticamente al modo de pesaje.
9. Presione la tecla OFF para apagar la balanza.
10. Situe el interruptor de modicacin de divisin a su posicin original.
11. Vuelva a precintar el interruptor de modicacin.
ENG FR ESP
Merci par utiliser notre srie SUPER SS de produit individuel/double ct protg contre lhumidit et leau.
La SUPER SS est une balance dacier inoxydable. La balance inclut des avances de grands techniques
dordinateur - contrle. Elle inclut une grande prcision des pesages, avec des facilits du transport et un prix
sous. Elle est rsistant et de longue dure. Elle peut tre utilise en magasins et pour peser diffrents paquets
de produits, ainsi quen lieux avec grand niveau dhumidit grce sa haute protection contre lhumidit.
Touche tare.
7
Manuel dusager Balance seul poids Modle Super SS
ENG FR ESP
2.2. MESSAGES DE LCRAN
3. GUIDE DOPRATIONS
3.1. PRPARATION
Ajuster le pied fonde, surveiller le niveau, situer le plateau horizontalement.
3.2.2. teint:
Presione durante unos segundos el botn OFF.
3.3. ZRO
Quand sans tare le poids montr sur lcran est 4% de capacit maximale, pousser la touche ON/ZERO, et
lcran montrera 0, le zro sallumera.
3.4. PESAGE
Situer le poids sur le plateau.
8
Modle Super SS Balance seul poids Manuel dusager
ENG FR ESP
3.8. CHARGE
Puissance supple par une batterie lead acide de recharge interne (6V/4Ah) Quand elle montrera -BAtLo-
sil vous plat teindre et charger immdiatement la batterie. Le temps de recharge complte cest de 12
heures.
4. NOTES
1. On doit charger la batterie comme minimum chaque 3 mois quand on nutilisera pas la balance pendant une
priode longue de temps. La charge durera quelques 12 heures.
2. Ne surcharger pas la balance. Ne jeter pas violemment objets pess sur la balance. Le dommage par sur-
charge ne se trouve pas dans le rang de garantie de subsistance.
3. Nutiliser pas objets aiguiss pour manier le clavier. Si la gomme est endommage, cela affectera la garantie
contre leau et lhumidit de la balance.
4. Maintenir la balance propre pour assurer un pesage correct.
5. Il y a une pose des scells de plomb la partie infrieure de la balance. Les usagers ne doivent pas enlever cette
pose des scells. Sil sendommage la pose des scells on ne assure pas la correcte subsistance de la balance.
5. CHANGEMENT DE DIVISION
1. Pousser ON/ZERO pour allumer la balance.
2. Pousser la touche TARE jusqu ce quil apparaisse la division dsire (nXXXX). Au recommencer pousser
la touche TARE il revient la division antrieure. La division qui apparat lcran est la division slectionne.
3. La balance revient automatiquement au mode de pesage.
6. CALIBRATION
Cette opration peut tre ralise seulement par personnel autoris par les lois de chaque pays.
1. Avec la balance teinte, enlever la pose des scells de linterrupteur de modi!cation de division situ la
part infrieure de la balance.
2. Changer la position de linterrupteur de modi!cation de division.
3. Pousser la touche ON/ZERO pour allumer la balance.
4. Pousser la touche TARE jusqu ce quil apparaisse CAL sur lcran.
5. Pousser la touche TARE nouvellement, il apparatra la capacit maximale de la balance.
6. Situer sur la balance le poids de la capacit maximale.
7. Atteindre 5 secondes.
8. Pousser la touche TARE nouvellement, il apparatra le message CaEnd lcran. La calibration a termin
et la balance revient automatiquement au mode de pesage.
9. Pousser la touche OFF pour teindre la balance.
10. Situer linterrupteur de modi!cation de division la position originale.
11. Recommencer plomber linterrupteur de modi!cation de division.
ENG FR ESP
Thank you for using our SUPER SS serial double side displays product of electronic waterproof counting scale.
SUPER SS are a stainless steel scale. The scale is manufactured with advances computer-controlled hi-tech-
niques. It has the characteristics of satisfactory in perfomance accurate in weighing, convenient for carrying,
cheap in price. It is sturdy and durable and widely used in not only retail stores and weighing of ration packing
of commodities but also in high humidity surroundings because of its well waterproof function.
Tare key.
Power off.
11
Users Guide Check Weight scale Model Super SS
ENG FR ESP
2.2 MENSAJES DE PANTALLA
3. OPERATION GUIDE
3.1. PREPARATION
Adjust the base foot, watch the level, make the pan in horitzontal.
3.2.3. Auto-off:
After 10 minutes in zeroing, auto-off.
3.3. ZERO
When without taring the weight display is 4% Max. capa., press the ON/ZERO key, the display shows 0,
the zero lamp lighting.
3.4. WEIGHING
Put weight to pan.
12
Model Super SS Check Weight scale Users Guide
ENG FR ESP
3.8. CHARGE
Power supplied by a internal rechargeable lead acid battery (6V/4Ah). When it shows -bAtLo-. Please turn off
and charge immediately. The time of full charging is 12 hours.
13
Users Guide Check Weight scale Model Super SS
ENG FR ESP
3.9.6 bUZZEr (set buzze)
When menu displays bUZZEr, press TARE to enter, press SET/0~9 to choose on or oFF, press TARE to
conrm.
4. NOTE
1. Not overloading. Not throw heavy things on the scale violently. The damage for overloading is not within the
range of guaranteed maintenance.
2. Dont use sharp thing to operation the keyboard. if the rubber is damaged it will in!uence the performance
of waterproof.
3. Keep the scale clean in order to weighing well.
4. There is a lead seal on the bottom of the scale. Users are not allowed to remove the seal. If the seal is da-
maged the scale is not guaranteed for maintenance.
5. a. You must charge the battery at least per 3 months when you dont use the scale for long time.
b. Please correctly connect line between adapter and battery, black to black, red to red.
c. If after charging the used time becomes short than often, please change a new battery.
5. DIVISION CHANGEMENT
1. Press ON/ZERO to turn on the scale.
2. Press TARE key until the wanted (nXXXX) division appears. When pressing TARE again it returns to the
previous division. The division that it appears on screen is the selected division.
3. The scale automatically returns to the weighing mode.
6. CALIBRATION
This operation can only be done by competent authorized personnel according to the laws of each country.
1. With the scale turned off, unseal the seal of the division modication switch. This switch is located in the
inferior face of the scale.
2. To change the position of the switch of division modication.
3. Press the button ON / ZERO to turn on the scale.
4. Press the TARE key until CAL appears in the screen.
5. Press the TARE key again, the maximum capacity of the scale will appear.
6. Locate on the scale the weight of its maximum capacity.
7. Wait 5 seconds.
8. Press the TARE key again, the message CaEnd will appear in the screen. The calibration has nished and
the scale automatically returns to the weighing mode.
9. Press the key OFF to turn off the scale.
10. Locate the switch of division modication to their original position.
11. Seal the modication switch again.
GIROPS S.L,
Sociedad domiciliada en
Socit domicilie
Society domiciled in:
EN55014-1:2006
EN55014-2: 1997/A1: 2001/A2:2008
EN61000-3-2: 2006
EN61000-3-3: 2008
EN61558-2-6:1997
EN61558-1:1997+A1:1998+A11:2003