Documentos de Académico
Documentos de Profesional
Documentos de Cultura
GD: .- Según limites de la IEEE C57.104-2008, el CO (838 ppm) y CO2 (4083 ppm) se encuentran en la CONDICION 3,
indicando recalentamiento en la celulosa y el total de gases combustibles se encuentran en la CONDICION 2,
indicando acumulación anormal de los gases combustibles.
.- Según el TRIANGULO DUVAL, las cantidades de gases combustibles detectados se deben a fallas térmicas que están
entre 300-700 °C. .-
Revisando valores de los gases combustibles desde el año 2018, los valores de los gases combustibles y el total de gases
combustibles tienen valores inestables por la regeneración o cambio de aceite del aceite realizada.
F: .- Se detecta <10 ppb del compuesto 2-furaldehido, indicando aislamiento celulósico en proceso de envejecimiento normal,
con este valor podemos calcular indirectamente el grado de polimerización del papel aislante GP=1003, por lo que se dice la
que la vida útil restante del transformador está al 100% respecto al papel aislante.
.- Revisando el historial de compuestos furanicos, se observa que los valores permanecen estables.
INH: .- El valor del contenido de Inhibidor de oxidación se encuentra aceptable para aceites del tipo I.
.- Revisando historial de contenido de inhibidor, se observan que los valores disminuyen considerablemente luego de la
regeneración o cambio de aceite realizada.
M: .- En el análisis se detecta Sn=0.8 ppm el cual es cuestionable, los valores de los demás metales que involucran la parte
interna del transformador se encuentran dentro de sus limites permisibles, estos valores nos servirán de base para futuros
diagnósticos. .- Revisando
historial de contenido de metales, se observa valores dentro de sus limites permisibles.
CONCLUSION:
* Condición Operativa : OBSERVADO (Exceso de gases combustibles disueltos en el aceite)
RECOMENDACIÓNES:
* Nuevo análisis completo : DOCE MESES
Atentamente,
REPORTE ANALISIS DE ACEITE
DATOS DEL TRANSFORMADOR
Cliente: EGASA N° Serie: 308013
Temp. de la Muestra de Aceite (°C): 30
Sub Est.: CT PISCO Cod. Equipo TGP1
Potencia (KVA): 50000 Tensión Max (KV): 60 Humedad Relativa (%): 30
Marca: KONKAR Año de Fab. 1999
Temp. Ambiente (°C): 30
Aceite (L): 14857 Tipo Aceite: Mineral
Atentamente,
WEIDMANN ELECTRICAL TECHNOLOGY REVISED TEST REPORT
650 AVENUE ORLY + DORVAL, PQ + H9P 1E9 01-7400177-640538-01
514.631.0888 + 514.631.0889 Page 1 of 3
WWW.WEIDMANN-ELECTRICAL.COM
JS ECOLOGY SAC Serial#: 308013 Mfr: Control#: 7400177
Location: PISCO kV: 60 Order#: 640538
Equipment: TRANSFORMER kVA: 50000 Account: 110498
COMAS, . LIMA 07 PE Compartment: MAIN(BOTTOM) Year Mf'd: 1999 Received: 11/09/2020
ATTN: ENRIQUE JUSTINO SILVA Breathing: CONS Syringe ID: 9 Reported: 11/26/2020
PO#: JS130-2020 Bank: Phase: 3 Bottle ID: 9
Project ID: Fluid: MIN Liters: 14857 Sampled By:
Customer ID: TGP1
Lab Control Number: 7400177 7312407
Date Sampled: 10/22/2020 04/01/2020
Order Number: 640538 612044
Oil Temp: 30 28
Dissolved Gas Analysis (DGA) Hydrogen (H2) (µL/L): 3 3
ASTM Methane (CH4) (µL/L): 19 17
D-36121 Ethane (C2H6) (µL/L): 3 3
Ethylene (C2H4) (µL/L): 7 6
Acetylene (C2H2) (µL/L): <1 <1
Carbon Monoxide (CO) (µL/L): 838 759
Carbon Dioxide (CO2) (µL/L): 4083 4051
Nitrogen (N2) (µL/L): 39311 35692
Oxygen (O2) (µL/L): 2494 2416
Total Dissolved Gas (TDG) (µL/L): 46758 42947
Total Dissolved Combustible Gas (TDCG) (µL/L): 870 788
Equivalent TCG (%): 1.4878 1.481
DGA DGA Keys Gas / Interpretive Method: Hydrogen within condition 1 limits (100 µL/L).
Diagnostics PER IEEE C57.104-2008 Methane within condition 1 limits (120 µL/L).
(most recent sample) Ethane within condition 1 limits (65 µL/L).
Ethylene within condition 1 limits (50 µL/L).
Acetylene within condition 1 limits (1 µL/L).
Carbon Monoxide: Condition 3 Indications of significantly overheated cellulose insulation (570
µL/L).
Carbon Dioxide: Condition 3 Significant Indications of overheated cellulose insulation (4000
µL/L).
TDCG: Condition 2 Levels exceed normal concentrations. Fault may be present (720 µL/L).
Notations: 1. Analysis is ISO/IEC 17025:2017 accredited, ANAB Accredited Certificate Number L2303.06 2. This test is conducted by a subcontracted laboratory. 3. Subcontracted laboratory has received ISO Standard 17025 accreditation for this test. 5.
This test is conducted by Weidmann Laboratory other than Primary Lab. 6. Weidmann Laboratory has received ISO Standard 17025 accreditation for this test. 7. Imported Sample: WEIDMANN Electrical Technology accepts no responsibility for these results;
accreditation status does not apply to these results. 8. Imported Equipment 10. mg/kg , µg/g, µg/mL, µL/L = ppm, µg/L = ppb, mN/m = dynes/cm, mm²/s = cSt
Accreditation applies to current analysis only. The analyses, opinions or interpretations contained in this report are based upon material and information supplied by the client. WEIDMANN Electrical Technology does not imply that the contents of the sample
received by this laboratory are the same as all such material in the environment from which the sample was taken. Our test results relate only to the sample or samples tested. Any interpretations or opinions expressed represent the best judgment of
WEIDMANN Electrical Technology. WEIDMANN Electrical Technology assumes no responsibility and makes no warranty or representation, expressed or implied as to the condition, productivity or proper operation of any equipment or other property for
which this report may be used or relied upon for any reason whatsoever. This test report shall not be reproduced except in full, without written approval of the laboratory.
WEIDMANN ELECTRICAL TECHNOLOGY REVISED TEST REPORT
650 AVENUE ORLY + DORVAL, PQ + H9P 1E9 01-7400177-640538-01
514.631.0888 + 514.631.0889 Page 2 of 3
WWW.WEIDMANN-ELECTRICAL.COM
JS ECOLOGY SAC Serial#: 308013 Mfr: Control#: 7400177
Location: PISCO kV: 60 Order#: 640538
Equipment: TRANSFORMER kVA: 50000 Account: 110498
COMAS, . LIMA 07 PE Compartment: MAIN(BOTTOM) Year Mf'd: 1999 Received: 11/09/2020
ATTN: ENRIQUE JUSTINO SILVA Breathing: CONS Syringe ID: 9 Reported: 11/26/2020
PO#: JS130-2020 Bank: Phase: 3 Bottle ID: 9
Project ID: Fluid: MIN Liters: 14857 Sampled By:
Customer ID: TGP1
Lab Control Number: 7400177 7312407
Date Sampled: 10/22/2020 04/01/2020
Order Number: 640538 612044
Oil Temp: 30 28
ASTM D-9241 Power Factor @ 100°C (Routine) (%): 0.640 0.852
ASTM D-40521 Density @15°C (g/mL): 0.8783 0.8786
ASTM D-26685, 6 Oxidation Inhibitor (wt. %) 0.049 0.049
GOQ Diagnostics Moisture in Oil: Acceptable for in-service oil (35 mg/kg max).
PER IEEE C57.106-2015 Interfacial Tension: Acceptable for in-service oil (25 mN/m min).
(most recent sample) Acid Number: Acceptable for in-service oil (0.2 mg KOH/g max).
Color Number and Visual: Diagnostic not applicable. Diagnostic not applicable.
Dielectric Breakdown ASTM D-877: Diagnostic not applicable.
Dielectric Breakdown ASTM D-1816: Acceptable for in-service oil (40 kV min @ 2mm).
Power Factor @ 25°C (Routine): Acceptable for in-service oil (0.5% max).
Power Factor @ 100°C (Routine): Acceptable for in-service oil (5% max).
Oxidation Inhibitor: Acceptable for in-service oil Type I (0.0% min and 0.08% max). Exceeds limit for in-service oil
type II (0.08% min and 0.3% max).
Comment:
Furanic Compound 2-Furaldehyde (µg/L): < 10 < 10
ASTM D-5837 5-Hydroxy-methyl-furaldehyde (µg/L): < 10 < 10
2-Acetylfuran (µg/L): < 10 < 10
5-Methyl-2-furaldehyde (µg/L): < 10 < 10
2-Furyl alcohol (µg/L): < 10 < 10
Furanic Compound Diagnostics (most recent sample):
New insulation with a high degree of mechanical strength will typically have a Degree of Polymerization (DP) of 1000-1300. "Middle Aged" paper is
approximately 500 and paper with less than 250 is in its "Old Age." Severely degraded insulation with a DP of 150 or less will have very little mechanical
strength and may result in a transformer failure. The above estimations are based on a study by Chendong of GSU transformers filled with mineral oil.
Estimated Average Degree of Polymerization (DP): >1003
Estimated Operating Age of the Equipment: <1.0
Notations:
Comment:
Metals Silver (Ag) (µg/g): < 0.5 < 0.5
Dissolved Aluminum (Al) (µg/g): < 0.5 0.9
Fault, Wear and Copper (Cu) (µg/g): < 0.5 < 0.5
Contamination Iron (Fe) (µg/g): < 0.5 < 0.5
ASTM D-71515 Lead (Pb) (µg/g): < 0.5 < 0.5
Silicon (Si) (µg/g): < 0.5 < 0.5
Tin (Sn) (µg/g): 0.8 < 0.5
Zinc (Zn) (µg/g): < 0.5 < 0.5
Comment:
Notations: 1. Analysis is ISO/IEC 17025:2017 accredited, ANAB Accredited Certificate Number L2303.06 2. This test is conducted by a subcontracted laboratory. 3. Subcontracted laboratory has received ISO Standard 17025 accreditation for this test. 5.
This test is conducted by Weidmann Laboratory other than Primary Lab. 6. Weidmann Laboratory has received ISO Standard 17025 accreditation for this test. 7. Imported Sample: WEIDMANN Electrical Technology accepts no responsibility for these results;
accreditation status does not apply to these results. 8. Imported Equipment 10. mg/kg , µg/g, µg/mL, µL/L = ppm, µg/L = ppb, mN/m = dynes/cm, mm²/s = cSt
Accreditation applies to current analysis only. The analyses, opinions or interpretations contained in this report are based upon material and information supplied by the client. WEIDMANN Electrical Technology does not imply that the contents of the sample
received by this laboratory are the same as all such material in the environment from which the sample was taken. Our test results relate only to the sample or samples tested. Any interpretations or opinions expressed represent the best judgment of
WEIDMANN Electrical Technology. WEIDMANN Electrical Technology assumes no responsibility and makes no warranty or representation, expressed or implied as to the condition, productivity or proper operation of any equipment or other property for
which this report may be used or relied upon for any reason whatsoever. This test report shall not be reproduced except in full, without written approval of the laboratory.
WEIDMANN ELECTRICAL TECHNOLOGY REVISED TEST REPORT
650 AVENUE ORLY + DORVAL, PQ + H9P 1E9 01-7400177-640538-01
514.631.0888 + 514.631.0889 Page 3 of 3
WWW.WEIDMANN-ELECTRICAL.COM
JS ECOLOGY SAC Serial#: 308013 Mfr: Control#: 7400177
Location: PISCO kV: 60 Order#: 640538
Equipment: TRANSFORMER kVA: 50000 Account: 110498
COMAS, . LIMA 07 PE Compartment: MAIN(BOTTOM) Year Mf'd: 1999 Received: 11/09/2020
ATTN: ENRIQUE JUSTINO SILVA Breathing: CONS Syringe ID: 9 Reported: 11/26/2020
PO#: JS130-2020 Bank: Phase: 3 Bottle ID: 9
Project ID: Fluid: MIN Liters: 14857 Sampled By:
Customer ID: TGP1
Lab Control Number: 7400177 7312407
Date Sampled: 10/22/2020 04/01/2020
Order Number: 640538 612044
Oil Temp: 30 28
Authorized By:
MUGUREL CONSTANTIN
SUPERVISING CHEMIST
Notations: 1. Analysis is ISO/IEC 17025:2017 accredited, ANAB Accredited Certificate Number L2303.06 2. This test is conducted by a subcontracted laboratory. 3. Subcontracted laboratory has received ISO Standard 17025 accreditation for this test. 5.
This test is conducted by Weidmann Laboratory other than Primary Lab. 6. Weidmann Laboratory has received ISO Standard 17025 accreditation for this test. 7. Imported Sample: WEIDMANN Electrical Technology accepts no responsibility for these results;
accreditation status does not apply to these results. 8. Imported Equipment 10. mg/kg , µg/g, µg/mL, µL/L = ppm, µg/L = ppb, mN/m = dynes/cm, mm²/s = cSt
Accreditation applies to current analysis only. The analyses, opinions or interpretations contained in this report are based upon material and information supplied by the client. WEIDMANN Electrical Technology does not imply that the contents of the sample
received by this laboratory are the same as all such material in the environment from which the sample was taken. Our test results relate only to the sample or samples tested. Any interpretations or opinions expressed represent the best judgment of
WEIDMANN Electrical Technology. WEIDMANN Electrical Technology assumes no responsibility and makes no warranty or representation, expressed or implied as to the condition, productivity or proper operation of any equipment or other property for
which this report may be used or relied upon for any reason whatsoever. This test report shall not be reproduced except in full, without written approval of the laboratory.
Equipment Type / Serial Number: TRANSFORMER / 308013
Equipment Location: PISCO
Client code / name: JSECOL / JS ECOLOGY SAC
Customer ID: TGP1
Duval Triangle
References
PD Partial discharge
Diagnosis
Ref. Sample Date Fault
X 10/22/2020 T2
Duval Triangle
References
PD Partial discharge
T1 Low-range thermal
fault (below 300 C)
T2 Medium-range
thermal fault (300-
700 C)
T3 High-range thermal
fault (above 700 C)
D1 Low-energy electrical
discharge
D2 High-energy electrical
discharge
DT Indeterminate -
Thermal fault or
electrical discharge
Diagnosis
Ref. Sample Date Fault
X 10/22/2020 T2
18/01/2020 T2