Documentos de Académico
Documentos de Profesional
Documentos de Cultura
RESUMEN
Durante esta práctica el objetivo fue realizar y comprender los parámetros físicos de una muestra
del laboratorio, los parámetros que se analizó fueron conductividad, turbiedad, y el procedimiento
para sólidos. Para medir la conductividad se utilizó un conductimetro en 200 ml de la muestra y
además se obtuvo la salinidad y los TDS, para medir la turbiedad se usó un tubímetro con una
muestra y se determinó que tan turbia se encontraba, para los sólidos sediméntales se vertieron un
litro de una muestra en dos conos de Imhoff y se tomaron las lecturas cada 30 min durante dos
horas más o menos, verificando que tanto solidos se habían sedimentado, para los sólidos totales se
tomó de la muestra en dos capsulas se calentaron hasta llegar a la evaporación para luego comparar
sus pesos iniciales y finales, en solidos disueltos se filtraron 50 ml de agua, se evaporizo y se colocó
a secar durante una hora aproximadente y se hizo la diferencia de sus pesos inicial y final, por
ultimo para los sólidos fijos que fue el más durable, se tomaron las capsulas de solidos totales y
solidos disueltos y se llevaron a la mufla durante una hora y los sólidos que se lograron apreciar
fueron llamados solidos fijos.
ABSTRACT
During this practice the objective was to realize and understand the physical parameters of a
laboratory sample, the parameters analyzed were conductivity, turbidity, and the procedure for
solids. To measure the conductivity a conductivity meter was used in 200 ml of the sample and in
addition the salinity and the TDS were obtained, to measure the turbidity a tube was used with a
sample and it was determined how turbid it was, for the sedimentary solids were poured one liter of
a sample in two Imhoff cones and the readings were taken every 30 min for two hours or so,
1
UNIVERSIDAD DE LA COSTA, CUC
DEPARTAMENTO DE CIVIL Y AMBIENTAL
PROGRAMA DE INGENIERÍA AMBIENTAL
verifying that both solids had settled, for the total solids the sample was taken in two capsules
heated until they reached evaporation and then compare their initial and final weights, in dissolved
solids 50 ml of water was filtered, evaporated and placed to dry for an approximate hour and the
difference of their initial and final weights was made, finally for fixed solids which was the most
durable, the capsules of total solids and dissolved solids were taken and taken to the muffle for an
hour and the solids that were appreciated were called solid solids.
2
UNIVERSIDAD DE LA COSTA, CUC
DEPARTAMENTO DE CIVIL Y AMBIENTAL
PROGRAMA DE INGENIERÍA AMBIENTAL
3
UNIVERSIDAD DE LA COSTA, CUC
DEPARTAMENTO DE CIVIL Y AMBIENTAL
PROGRAMA DE INGENIERÍA AMBIENTAL
4
UNIVERSIDAD DE LA COSTA, CUC
DEPARTAMENTO DE CIVIL Y AMBIENTAL
PROGRAMA DE INGENIERÍA AMBIENTAL
ANEXOS
Cálculos:
La fórmula para solidos totales :
𝑚𝑔 1000 ∗ (𝐴 − 𝐵)
𝑆𝑇( ) =
𝐿 𝑉
𝑑𝑜𝑛𝑑𝑒:
𝐴 = 𝑝𝑒𝑠𝑜 𝑑𝑒 𝑙𝑎 𝑐á𝑝𝑠𝑢𝑙𝑎 + 𝑟𝑒𝑠𝑖𝑑𝑢𝑜, 𝑚𝑔
𝐵 = 𝑝𝑒𝑠𝑜 𝑑𝑒 𝑙𝑎 𝑐𝑎𝑝𝑠𝑢𝑙𝑎, 𝑚𝑔
𝑉 = 𝑣𝑜𝑙𝑢𝑚𝑒𝑛 𝑑𝑒 𝑙𝑎 𝑚𝑢𝑒𝑠𝑡𝑟𝑎, 𝑚𝑙
5
UNIVERSIDAD DE LA COSTA, CUC
DEPARTAMENTO DE CIVIL Y AMBIENTAL
PROGRAMA DE INGENIERÍA AMBIENTAL
𝑺𝑻 = 𝟖𝟎 𝒎𝒈/𝒍
Resultados de solidos sedimentables
(Cada 30 minutos)
Capsula 2
Cono 1
1000 ∗ (51574.2𝑚𝑔 − 51564.4𝑚𝑔)
𝑆𝑇 =
50 𝑚𝑙 5 ml/L
6 ml/L
𝑺𝑻 = 𝟗𝟐𝟖𝟑𝟔 𝒎𝒈/𝒍 7 ml/L
8 ml/ L
𝑚𝑔 1000 ∗ (𝐴 − 𝐵) 5 ml/L
𝑆𝐷 ( ) =
𝐿 𝑉 7 ml/L
8 ml/L
𝐴 = 𝑝𝑒𝑠𝑜 𝑑𝑒 𝑙𝑎 𝑐𝑎𝑝𝑠𝑢𝑙𝑎 9 ml/L
+ 𝑟𝑒𝑠𝑖𝑑𝑢𝑜 𝑓𝑖𝑙𝑡𝑟𝑎𝑑𝑜
𝐵 = 𝑝𝑒𝑠𝑜 𝑑𝑒 𝑙𝑎 𝑐𝑎𝑝𝑠𝑢𝑙𝑎, 𝑚𝑔 Solidos fijos totales
𝑉 = 𝑣𝑜𝑙𝑢𝑚𝑒𝑛 𝑑𝑒 𝑙𝑎 𝑚𝑢𝑒𝑠𝑡𝑟𝑎, 𝑚𝑙 Capsula 1
1000 ∗ (5157 𝑚𝑔 − 5001 𝑚𝑔)
1000 ∗ (49281 𝑚𝑔 − 48489 𝑚𝑔) 𝑆𝐹𝑇 =
𝑆𝐷 = 50 𝑚𝑙
50 𝑚𝑙
Capsula 2
Capsula 2
1000 ∗ (49281.2 𝑚𝑔 − 48489. 𝑚𝑔)
𝑆𝐷 = 1000 ∗ (4924 𝑚𝑔 − 4844 𝑚𝑔)
50 𝑚𝑙 𝑆𝐹𝑇 =
50 𝑚𝑙
𝑆𝐷 = 15840 𝑚𝑔/𝑙
𝑺𝑭𝑻 = 𝟏𝟓𝟗𝟖
Solidos suspendidos
6
UNIVERSIDAD DE LA COSTA, CUC
DEPARTAMENTO DE CIVIL Y AMBIENTAL
PROGRAMA DE INGENIERÍA AMBIENTAL
Capsula 1
𝑆𝑉𝑇 = 80 − 3120
𝑺𝑽𝑻 = −𝟑𝟎𝟒𝟎 𝒎𝒈/𝒍
𝒄𝒂𝒑𝒔𝒖𝒍𝒂 𝟐