Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Comprobador de Diagnostico P-79
Comprobador de Diagnostico P-79
Certificado de Calibración
Calibration Certificate
Laboratorio de Metrología Magnitud: ELECTRICA
Electrical Metrology Laboratory
El lapso de confirmación metrológica es establecido por el usuario en base a su programa de calibración, es responsabilidad del usuario la recalibración en los intervalos adecuados.
Los resultados del presente certificado deben interpretarse como antes y después de la calibración, ya que no se realizan ajustes o reparaciones durante el proceso.
Este certificado tiene validez únicamente en su forma íntegra, no se permite la reproducción parcial de este documento, sin la autorización por escrito de Asesoría y Servicios Integrales en Calibración S.C.
(This certificate is not valid without the corresponding signatures and stamp and it may not be reproduced other than in full, except with the prior written approval of the issuing Laboratory).
Asesoría y Servicio Integral de Calibración, S.C.
NUESTRO COMPROMISO POR LA CALIDAD
Resultados de la Calibración
Electrical Metrology Laboratorio
Laboratorio de Metrología Magnitud: ELECTRICA
PROTECCION
MEDICIONE MEDICION MEDICION
RANGO RESOLUCION EXACTITUD DE
S PATRON INSTRUMENTO
SOBRECARGA
VDC 0-36 V 27.5V 27.49V 0.01V 0.05% +2 120Vrms
VAC-DMM 0-24 Vacrms 13varms 12.99varms 0.01Vac 0.1% +3 120Vrms
Adc 0-70 A 55 A 55 A 0.01A (+-) 3% de lectura (+-) 1A 1000A rms
Adc 0-700 A 322A 322A 0.1A (+-) 3% de lectura (+-) 1A 1000A rms
Aac 0-70 A 26 A 26.01A 0.01A (+-) 3% de lectura (+-) 1A 1000A rms
Aac 0-700 A 450 A 449.02 A 0.01A (+-) 3% de lectura (+-) 1A 1000A rms
10 Ohms-2meg
Ohm ohms 10 Ohms 10 Ohms 1 Ohm 2.0% +4 120 Vrms
continuidad < 10 Ohms 15 Ohms 15 Ohms 1 Ohm 2.0% +4 120 Vrms
diodo 0-1.5 V 1.5 v 1.5 v 0.01 V 0.05% +2 120 Vrms
temperatura oc-150 C 100 C 100 C 1 deg F 1.0% +5 na
EL ERROR DE MEDIDA EXPRESADO, ES EL ERROR DEL INSTRUMENTO BAJO CALIBRACIÓN QUE SE DETERMINA EN BASE A LA SIGUIENTE FORMULA:
ERROR DE MEDIDA= (Valor instrumento de medida-Valor patrón de medida),donde ambos se obtienen de un promedio de 10 Mediciones, aplicando todas las correcciones correspondiente.
LA INCERTIDUBRE DE LA MEDIDA SE OBTUVO MULTIPLICANDO LA INCERTIDUBRE COMBINADA POR UN FACTOR QUE ASEGURA UN NIVEL DE CONFIANZA DE AL MENOS 95% EN
VALOR FACTOR DE COBERTURA ES K=2. LA INCERTIDUNBRE DE LA MEDIDA FUE ESTIMADA DE ACUERDO A LA NORMA NMX-CH-140-IMNC.2002 “Guia para la expresión de la incertidubre
en las mediciones”, EQUIVALENTE AL DOCUMENTO “Guide to the of uncertainly in measurement BIPM, IEC, IFCC, ISO, IUPAP, OIML (1995)”.
ES RESPONSABILIDAD DEL USUARIO EL CALCULAR LA INCERTIDUMBRE POR INTERPOLACIÓN, CUANDO EL INSTRUMENTO SE USA EN PUNTOS DIFERENTES A LOS CALIBRADOS.
EL PRESENTE CERTIFICADO SOLO AMPARA LAS MEDICIONES REPORTADAS EN EL MOMENTO Y CONDICIONES AMBIENTALES Y DE USO EN QUE SE REALIZO ESTA CALIBRACIÓN
Este certificado tiene validez únicamente en su forma íntegra, no se permite la reproducción parcial de este documento, sin la autorización por escrito de Asesoría y Servicios Integrales en Calibración S.C.
(This certificate is not valid without the corresponding signatures and stamp and it may not be reproduced other than in full, except with the prior written approval of the issuing Laboratory).