Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Respuesta correcta
La respuesta correcta es: These materials typically have strengths greater in comprensión than in tension. → Brittle material, The
safety factor is based on Sy → Ductil material, When designing, is necessary to control the deformation → Ductil material, The
safety factor is based on Sut or Suc → Brittle material, Have similar properties in tension and compression. → Ductil material
d. Distorsion energy
e. Criterio de Balandin
https://campus.uaovirtual.edu.co/mod/quiz/review.php?attempt=200987&cmid=45261 1/6
13/4/2020 Exam about Design Under Static Load
Pregunta El circulo de Mohr se aplica para: Bienestar Herramientas JUAN DAVID GALLON VALDER…
3
Seleccione una:
Correcta
Español - Internacional (es)
a. Determinar los esfuerzos uctuantes actuantes en una sección transversal cualquiera de una pieza.
Puntúa 0,25
sobre 0,25
b. Gra car los esfuerzos normales respecto de su comportamiento en el tiempo.
c. Determinar los esfuerzos máximos que pueden llegar a presentarse a una inclinación cualquiera del elemento diferencial
de Área.
d. Calcular los esfuerzos que están actuando en un eje por efecto de las cargas aplicadas.
Respuesta correcta
La respuesta correcta es: Determinar los esfuerzos máximos que pueden llegar a presentarse a una inclinación cualquiera del
elemento diferencial de Área.
Pregunta The Figure shows an electric motor loaded by a belt drive. The diameter of the steel (Sy=37246 lb/pulg2) shaft is d=2,2 in, and their
4 length is L= 2 in. The power is transmitted using a pulley with a diameter of 6 inches and the tension in the tight side is F1= 2833 lb.
Calculate the safety factor to the shaft using the von Mises theory (Neglect stress concentration).
Correcta
Puntúa 1,00
sobre 1,00
Respuesta: 4,32
https://campus.uaovirtual.edu.co/mod/quiz/review.php?attempt=200987&cmid=45261 2/6
13/4/2020 Exam about Design Under Static Load
Pregunta Bienestar
El eje mostrado en la Figura se somete a un momento torsor igual a 5578 Herramientas
N-m, como se muestra. ElJUAN DAVID
eje esta GALLON
hecho de unVALDER…
Acero
5 AISI 1045 Maquinado (Sy= 698 MPa, Sut= 1403 MPa) y el factor de concentrador de esfuerzos para los dos cambios de sección es
Kt= 2,53 (tanto para los esfuerzos normales como cortantes). Determine el valor del diametro (D2 en mm) para la sección C,
Correcta
usando un factor de seguridad de 2,5 y el criterio de von Mises como teoría de falla. Español - Internacional (es)
Puntúa 1,00
sobre 1,00
Respuesta: 74
https://campus.uaovirtual.edu.co/mod/quiz/review.php?attempt=200987&cmid=45261 3/6
13/4/2020 Exam about Design Under Static Load
Seleccione una:
a.
b.
https://campus.uaovirtual.edu.co/mod/quiz/review.php?attempt=200987&cmid=45261 4/6
13/4/2020 Exam about Design Under Static Load
c.
d.
Respuesta correcta
https://campus.uaovirtual.edu.co/mod/quiz/review.php?attempt=200987&cmid=45261 5/6
13/4/2020 Exam about Design Under Static Load
Pregunta The Figure shows an electric motor loaded by a belt drive. The diameter Bienestar
of the steel Herramientas JUAN
(Sy=38868 lb/pulg DAVIDisGALLON
2) shaft d=3,8 in,VALDER…
and their
7 length is L= 6 in. The power is transmitted using a pulley with a diameter of 6 inches and the tension in the tight side is F1= 4144 lb.
Calculate the safety factor to the shaft using the Tresca criterion (Neglect stress concentration).
Sin contestar
Español - Internacional (es)
Puntúa como
1,00
Respuesta:
Pregunta The Figure shows a solid cylinder, attached at the one end and loaded with a pipe wrench at the other that applied a load P=1867 lb.
8 The pipe wrench produce bending stress and torsional stress. If d=2,0 in, L1=4,3 in and L2=5 in, what is the magnitude (lb/in2) of
the maximum von Mises stress at A?
Sin contestar
Puntúa como
1,00
Respuesta:
https://campus.uaovirtual.edu.co/mod/quiz/review.php?attempt=200987&cmid=45261 6/6