Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Tesis Interesante PDF
Tesis Interesante PDF
Profesor Guía:
Sr. Galo Valdebenito M.
Ingeniero Civil U. de Concepción
Copyright 1984-2002 Computers and Structures Inc.
SUMMARY
The objective of this thesis is to study the posibility of materializing high steel structured
buildings in Chile, and to prove that they may present similar characteristics in their
mechanic response, seismic resistance and costs to the steel buildings with core of re-
enforced concrete.
The study was centered on the development of the structural analysis of two buildings
structured on the basis of: first, steel rigid frames at the periphery and walls of re-enforced
concrete at the core of stairs and elevator, and, secondly, steel rigid frames at the periphery
and concentrically braced frames at the core. Each building is 87 meters high, and each one
with 30 stories.
The seismic analysis was developed on the basis of the NCh 433.Of96 code. The
measurement of the steel elements was carried out according to the load and resistance factor
method, and that of the re-enforced elements according to the ultimate resistance method.
The analysis and design were effected with the ETABS software in its version 8.
From the results presented in this work it is concluded that this type of steel structure is
possible from the technical point of view. As far as the seismic response is concerned, it was
possible to prove that it is perfectly possible to build this type of structures according to the
NCh433.Of96 code and that it presents similar parameters (periods, displacements, etc.) to
the steel buildings with re-enforced concrete core.
Copyright 1984-2002 Computers and Structures Inc.
Agradecimientos:
trabajo:
apoyo y disposición.
momentos difíciles.
A Dios y mis padres, que supieron
CAPÍTULO I
INTRODUCCIÓN 1
1.1 Presentación del Problema 2
1.2 Objetivo 3
1.3 Metodología 3
CAPÍTULO II
ANTECEDENTES GENERALES DE EDIFICACIÓN EN ALTURA 4
2.1 Antecedentes Previos, Edificios en Chile 5
2.2 Diseño Sismorresistente 8
2.3 Tipos de Estructuración para Edificios en Altura 9
2.4 Respuesta Sísmica de Estructuras de Acero 12
2.4.1 Respuesta de Distintos Sistemas Estructurales 12
CAPÍTULO III
CONSIDERACIONES GENERALES Y BASES DE CALCULO 16
3.1 Bases de Cálculo 17
3.1.1 Descripción del Proyecto 17
3.1.2 Materiales Empleados 17
3.1.3 Calidades y Propiedades de los Materiales 18
3.1.4 Metodología de Diseño 19
3.1.5 Solicitaciones 19
3.1.6 Combinaciones de Carga 19
3.1.7 Metodología de Análisis 20
3.1.8 Descripción del Sistema Sismorresistente 20
3.1.9 Hipótesis de Diseño 21
3.1.10 Normas y Códigos Utilizados 22
3.2 Descripción Sistemas Utilizados 23
3.2.1 Uniones 33
3.2.2 Arriostramientos 26
3.2.3 Diafragma Rígido 26
3.2.4 Torsiones 27
3.2.5 Recomendaciones Norma Chilena 27
3.2.6 Espectros de Diseño 30
3.3 Estructuraciones, Plantas y Elevaciones 35
3.4 Modelación Estructural 49
3.4.1 Generalidades 49
3.4.2 Modelación 50
CAPÍTULO IV
ANÁLISIS Y ESTUDIO COMPARATIVO
DE LOS SISTEMAS ESTRUCTURALES 70
4.1 Análisis Sísmico 71
4.1.1 Edificio Mixto 71
4.1.2 Edificio Acero 78
4.2 Deformaciones 85
4.2.1 Edificio Mixto 86
4.2.2 Edificio Acero 94
4.3 Excentricidad Arriostramientos 102
4.4 Evaluación Económica 104
4.5 Comparación de Resultados 105
CAPÍTULO V
CONCLUSIONES 106
5.1 Factibilidad 107
5.2 Análisis Dinámico 107
5.3 Variables Estructurales 107
5.4 Excentricidad en Arriostramientos 108
5.5 Consideraciones Finales 108
BIBLIOGRAFÍA 109
CAPITULO I
Introducción
1.1 PRESENTACIÓN DEL PROBLEMA
Es por esto, que los ingenieros civiles buscan día a día nuevas técnicas y
procesos de diseño, materiales de mejor calidad o sistemas constructivos más óptimos,
para asegurar un comportamiento deseable en las estructuras proyectadas.
2
Lo anterior, refleja que en Chile no existe una gran experiencia en el estudio de
este tipo de edificios en acero, por lo que, la presente memoria, pretende crear una
base de discusión y análisis de la posibilidad de diseñar grandes estructuras, ya sea de
sistemas de acero puro, o de sistemas duales que combinen el acero con el hormigón
armado y que, a pesar de ser un país con grandes sismos, nos atrevamos a traspasar
nuestros propios temores y nos sumerjamos en las corrientes que impulsan este mundo
globalizado con experiencias tan o más enriquecedoras que las nuestras.
1.2 OBJETIVO
1.3 METODOLOGÍA
3
CAPITULO II
Los edificios más conocidos de esta nueva generación, producto de los factores
antes comentados, corresponden a: Hoteles Sheraton (fig. 2.1), Hyatt (fig. 2.4) y
Marriott (fig. 2.6); El World Trade Center; Los edificios corporativos de la CTC (fig.
2.3), Interamericana, Consorcio de Seguros (fig. 2.2) y Edificio de la Industria (fig.
2.5); Los edificios de oficinas de Las Américas, Metrópolis, Torre El Bosque, Edificio
Milenium y Edificio del Pacífico, entre muchos otros.
5
Isabel. Estos casos significan únicamente del orden del 1 o 2% de los casos totales.
En la tabla 2.1, se presenta una comparación entre la utilización del acero en nuestro
país y en los países desarrollados, presentado por don Elías Arce L., en el Segundo
Curso Internacional del Acero, en Noviembre de 1998.
PAISES
INDICE CHILE
DESARROLLADOS
Infraestructura, % 9 60
Estructuras Industriales, % 90 90
FIGURA 2.1: Edificio Hotel Sheraton FIGURA 2.2: Edificio Corporativo Consorcio de Seguros
6
FIGURA 2.3: Edificio Corporativo de la CTC FIGURA 2.4: Edificio Hotel Hyatt
7
2.2 DISEÑO SISMORRESISTENTE
Los buenos resultados obtenidos por la ingeniería nacional sugieren que el diseño
Sismorresistente en nuestro país no se debe apartar de las líneas que han seguido los
edificios tradicionalmente, lo que también es aplicable a los edificios de estructura de
acero.
La experiencia chilena dice que además de ser necesario dotar a los edificios de
una rigidez adecuada, se debe evitar las posibles irregularidades en planta y altura,
trasmitir las cargas normales y sísmicas lo más directamente posible a las fundaciones
sin cambios bruscos de dirección, evitar los traspasos de cargas a través de los
diafragmas, evitar el fenómeno de piso blando, columna corta y cualquier otro tipo de
situaciones que signifique concentración de tensiones.
En este punto surge la interrogante ¿Cuáles son los parámetros que aseguran
una adecuada rigidez y regularidad estructural?
8
Si un edificio alto de acero (entre 20 y 40 pisos para el caso chileno) se puede
ajustar a los parámetros normales de los edificios de hormigón armado o de una
combinación de éstos, y su dimensionamiento se realiza de acuerdo a la normativa
vigente y con conexiones de ductilidad, no existe razón para dudar de su segundad
sísmica, que será tan buena o superior a las de sus símiles de hormigón armado o de
sistemas mixtos.
Los elementos resistentes que transmiten cargas verticales son las losas, vigas,
columnas y muros. A estos elementos hay que agregar las fundaciones, que son los
ensanchamientos que experimenta el esqueleto resistente en su parte inferior con el fin
de disminuir el nivel de las tensiones que se transmiten al terreno. Los elementos que
9
transmiten cargas horizontales son las losas (a través del trabajo en su plano), vigas,
columnas y muros, pero la forma en que trabajan estos elementos en este caso es
diferente al caso de las cargas verticales.
En la práctica, los dos tipos de estructuración básica que se han discutido se pueden
presentar combinadas. Sin embargo, la rigidez lateral de pórticos y muros es muy diferente,
lo cual implica que la introducción de muy pocos muros en una estructuración de pórticos hace
que los muros pasen a absorber la casi totalidad de las cargas horizontales ya que su
rigidez frente a este tipo de cargas es mucho mayor. La deformación lateral de ambos tipos
como función de la altura también es diferente, lo cual implica que, al compatibilizar las
deformaciones de ellos, los muros tiendan a tomar una mayor proporción de la carga en los
niveles inferiores, y lo inverso suceda en los niveles superiores.
10
elementos no estructurales y en el equipamiento del edificio. Este último aspecto también
hace que se inhiba la aparición de otros efectos secundarios, que no se consideran
comúnmente en el análisis, como el efecto P- Δ, esto es, la aparición de esfuerzos
adicionales producidos por las cargas verticales actuando en los desplazamientos
horizontales de la estructura. Estas ventajas superan largamente el aspecto
desfavorable que representa su alta rigidez, bajo periodo fundamental de vibración y
atracción de esfuerzos sísmicos mayores, ya que simultáneamente, las estructuraciones
de muros presentan una significativa resistencia lateral.
(elevación) (elevación)
(planta) (planta)
11
2.4 RESPUESTA SÍSMICA DE ESTRUCTURAS DE ACERO
1
Brockenbrough, R., Merritt, F., “Manual de Diseño de Estructuras de Acero, Tomo II” (Ref. 1)
12
Los pórticos con arriostramiento concéntrico (fig. 2.10), en los cuales los
miembros están sujetos primordialmente a fuerzas axiales, proveen en forma
económica mucha mayor resistencia y rigidez que un pórtico resistente a momento
con la misma cantidad de acero. Existe un amplio intervalo de configuraciones de
arriostramiento, y considerables variaciones en el funcionamiento estructural pueden
resultar de estas diferentes configuraciones. Las riostras, que proveen la parte
principal de la rigidez en pórticos con dicho arriostramiento, atraen fuerzas muy
grandes de compresión y tensión durante un terremoto. En consecuencia, el pandeo
por compresión de las riostras con frecuencia domina el comportamiento de estos
pórticos. Por lo tanto, los pórticos arriostrados concéntricamente se consideran como
más rígidos, más fuertes pero menos dúctiles que los pórticos de acero que resisten
momento. Se requieren diferentes provisiones de diseño para pórticos con
arriostramiento concéntrico que para pórticos de acero resistentes a momento.
13
Los pórticos arriostrados excéntricamente (fig. 2.11), en los cuales al menos
un extremo de cada diagonal de arriostramiento interseca una viga en un punto
alejado de la unión columna – viga, pueden combinar la resistencia y rigidez de los
pórticos arriostrados concéntricamente con la buena ductilidad de los pórticos
resistentes a momento. Los pórticos arriostrados excéntricamente incorporan en
forma deliberada una excentricidad controlada en las conexiones de las riostras. La
excentricidad y las vigas de empalme se escogen con cuidado para impedir el pandeo
de las riostras, y proveen un mecanismo dúctil para la disipación de la energía. Si se
diseñan de manera apropiada, los pórticos con arriostramiento excéntrico resultan en
un buen funcionamiento inelástico, pero requieren todavía otro grupo de provisiones
de diseño,
14
Los sistemas duales, como marcos de acero que resisten momento,
combinados con pórticos de acero con arriostramientos concéntricos o con muros de
hormigón, pueden combinar la resistencia y rigidez de un pórtico arriostrado y de un
muro de cortante con el buen funcionamiento inelástico de los pórticos especiales de
acero resistentes a momento. A los sistemas duales con frecuencia se les asigna un
valor de R y una fuerza sísmica de diseño intermedios entre los requeridos por cual-
quiera de esos sistemas cuando operan solos. Las provisiones de diseño incluyen
límites y recomendaciones con relación a la rigidez relativa y a la distribución de la
resistencia de las dos componentes. Los sistemas duales han conducido a un amplio
intervalo de combinaciones estructurales para el diseño sísmico. Muchas de ellas son
sistemas estructurales compuestos o híbridos. Sin embargo, los pórticos de acero con
placas de piso de hormigón trabajando en acción compuesta no se usan comúnmente
para el desarrollo de resistencia sísmica, aunque los pisos de acción compuesta por
lo general se usan en el diseño para cargas gravitacionales.
15
CAPITULO III
3.1.1.1 Proyecto:
El proyecto consiste en el estudio de dos edificio de treinta niveles cada uno,
destinados a oficinas, la altura total de cada edificio es de 87 m, con una superficie útil
de 18.900 m2
3.1.1.2 Ubicación:
El proyecto está ubicado en la ciudad de Santiago, Región Metropolitana.
3.1.1.3 Estructuración:
La estructura de edificio se basa en:
17
3.1.3 CALIDADES Y PROPIEDADES DE LOS MATERIALES
3.1.3.1 Hormigón:
3.1.3.2 Acero:
Refuerzo:
• Módulo de Elasticidad Es: 2.1×1010 kg/m2
• Densidad: 7850 kg/m3
• Módulo Poisson νs = 0.25
• Módulo de Corte Gs = 0.4 × Es
• Coef de Dilatación térmica αs = 1.2×10-5
• Tensión de Fluencia fy: 28000000 kg/m2
Estructural
• Módulo de Elasticidad Ese: 2.1×1010 kg/m2
• Densidad: 7850 kg/m3
• Módulo Poisson νse = 0.3
• Módulo de Corte Gse = 0.4 × Es
• Coef. de Dilatación térmica αs = 1.2×10-5
• Tensión de Fluencia fy: 27000000 kg/m2
• Muros: 2 cm
• Vigas: 2.5 cm
• Losas: 2 cm
(*)
Valor práctico más cercano a realidad de hormigones chilenos.
18
3.1.4 METODOLOGÍA DE DISEÑO
3.1.4.2 Acero:
Los elementos de Acero serán diseñados considerando el Método de Factores
de Carga y Resistencia.
3.1.5 SOLICITACIONES
• 1.4PP
• 1.4PP + 1.7SC
• 0,75 ( 1.4PP + 1.7SC ± 1.7V )
• 0.9PP ± 1.3V
• 0,75 ( 1.4PP + 1.7SC ± 1.87S )
• 0.9PP ± 1.43S
19
3.1.6.2 Método de Factores de Carga y Resistencia
• 1.4PP
• 1.2PP + 1.6 SC
• 1.2PP + 0.5SC ± 1.3V
• 0.9PP ± 1.3V
• 1.2PP ± 0.8V
• 1.4PP + 1.4SC ± 1.4S
• 0.9PP ± 1.4S
Copyright 1984-2002 Computers and Structures Inc.
20
arriostrados, provee un control de las deformaciones laterales debido a su
considerable rigidez lateral.
Los edificios están divididos en tres secciones, las que son idénticas entre sí:
del piso 1 al 10, del piso 11 al 20 y del piso 21 al 30.
Se presenta una simetría perfecta con respecto a uno de los ejes del edificio.
21
3.1.9.2 Acero:
• NCh 432 0f71: "Calculo de acción del viento sobre las construcciones" .
• NCh 433 0f96: "Diseño sísmico de edificios".
• NCh 1537 0f86: "Diseño estructural de edificios - Cargas permanentes y
sobrecargas de uso"
• NCh 430 EOf61: "Hormigón Armado – II Parte"
• Código AC1 318 - 99.
• Código AISC LRFD - 93.
22
3.2 DESCRIPCIÓN SISTEMAS UTILIZADOS
3.2.1 UNIONES
En este caso se utilizará una conexión apernada de cizalle, como los de la figura
3.1. Se eligió este tipo de conexión para evitar momentos indeseados en el alma de la
columna que puedan comprometer la estabilidad del sistema.
Se utilizará conexión apernada de momento, como los de la figura 3.2. Este tipo
de unión, que transmite tanto cortante como momento, proporciona al sistema
resistencia a las fuerzas laterales.
23
FIGURA 3.2: Conexión de momento apernada de viga a ala de columna.
Esquema tipo.
24
FIGURA 3.4: Conexión de arriostramiento concéntrico en V invertida a viga.
Esquema tipo.
25
3.2.2 ARRIOSTRAMIENTOS
El arriostramiento diagonal, figura 3.6 (a), actúa a tensión para cargas laterales en
una dirección, y a compresión para dichas cargas en la otra dirección. Se requiere que la
dirección de la inclinación del arriostramiento en sistemas con arriostramiento diagonal
esté balanceada, ya que las riostras tienen mucha mayor capacidad a tensión que a
compresión.
(a) (b)
26
La función sísmica de las losas, o acción de diafragma, consiste en compatibilizar
los desplazamientos horizontales de los elementos resistentes con los tres grados de
libertad de la planta, a través del uso de la considerable rigidez que las losas tienen en
su plano.
3.2.4 TORSIONES
Las plantas de los diferentes pisos de los edificio presentan una perfecta simetría
con respecto a uno de su ejes y en el otro sentido poseen una muy buena distribución
de los elementos haciendo las plantas casi simétricas con respecto a ese eje. Sin
embargo, fue necesario considerar las posibles torsiones accidentales que sugiere la
norma, esto es aplicando momentos de torsión estáticos en cada nivel, calculados como
el producto de la variación del esfuerzo de corte combinado en ese nivel, por una
excentricidad accidental dada por:
27
Esta norma no se aplica al diseño sísmico de otras obras civiles, tales como
puentes, presas, túneles, acueductos, muelles, canales. Tampoco se aplica a
edificios industriales ni a instalaciones industriales. El diseño de estas obras debe regirse
por la norma chilena correspondiente.
Esta norma, aplicada en conjunto con las normas de diseño específicas para
cada material, está orientada a lograr estructuras que:
La norma entrega una serie de disposiciones entre las cuales podemos destacar:
• Disposiciones de aplicación general
• Disposiciones generales sobre diseño y métodos de análisis
• Métodos de análisis
• Diseño y construcción de fundaciones
• Elementos secundarios
Material Densidad
Acero 7850 kg/m3
Hormigón Armado 2500 kg/m3
Sobrecarga de uso 250 kg/m2
Muro cortina 150 kg/m2
29
3.2.6 ESPECTROS DE DISEÑO
IA o α
Sa =
R*
donde
I = coeficiente relativo a la importancia, uso y riesgo de falla del edificio.
Ao = aceleración efectiva máxima del suelo.
Los que se obtienen de las tablas 6.1 y 6.2, respectivamente, de dicha norma.
p
T
1 − 4,5 n
α= To
3
Tn
1+
To
en que
Tn = período de vibración del modo n
To = parámetro que depende del tipo de suelo
p = parámetro que depende del tipo de suelo
To y p se obtienen de la tabla 6.3 de la norma.
El factor de reducción R* se determina de:
T*
R* = 1 +
T*
0,10T o +
Ro
30
donde:
T* = período del modo con mayor masa traslacional equivalente en la dirección
del análisis.
Ro = factor de modificador de la respuesta estructural según tabla 5.1 de la
norma.
Copyright 1984-2002 Computers and Structures Inc.
31
3.2.6.2 Edificio Mixto
Datos:
Clase C Zona 2 Suelo II
I Ao To (s) p S Ro T* (s) R*
1 0,3 g 0,3 1,5 1 11 2,1254 10,82
Con estos datos se obtuvieron los siguientes valores del espectro, sólo se
presenta una muestra significativa de éstos:
Tn (s) α Sa/g
0,05 1,300 0,0370713
0,06 1,391 0,0396715
0,07 1,488 0,0424352
0,08 1,590 0,0453219
0,09 1,694 0,0482918
0,1 1,799 0,0513052
0,2 2,661 0,0758733
0,3 2,750 0,0784099
0,4 2,352 0,0670711
0,5 1,898 0,0541041
0,6 1,525 0,0434911
0,7 1,243 0,0354523
0,8 1,032 0,0294167
0,9 0,871 0,0248292
1 0,746 0,0212783
1,2 0,569 0,0162303
1,4 0,452 0,0128812
1,6 0,370 0,0105357
1,8 0,309 0,0088214
2 0,264 0,0075248
2,2 0,229 0,0065168
2,4 0,200 0,0057150
2,6 0,178 0,0050649
2,8 0,159 0,0045293
3 0,143 0,0040819
3,2 0,130 0,0037035
3,4 0,119 0,0033802
3,6 0,109 0,0031013
3,8 0,100 0,0028588
4 0,093 0,0026463
4,2 0,086 0,0024589
4,4 0,080 0,0022926
32
3.2.6.3 Edificio Acero
Datos:
Clase C Zona 2 Suelo II
I Ao To (s) p S Ro T* (s) R*
1 0,3 g 0,3 1,5 1 11 2,6453 10,78
Con estos datos se obtuvieron los siguientes valores del espectro, sólo se
presenta una muestra significativa de éstos:
Tn (s) α Sa/g
0,05 1,300 0,0361829
0,06 1,391 0,0387208
0,07 1,488 0,0414183
0,08 1,590 0,0442359
0,09 1,694 0,0471346
0,1 1,799 0,0500758
0,2 2,661 0,0740551
0,3 2,750 0,0765309
0,4 2,352 0,0654638
0,5 1,898 0,0528075
0,6 1,525 0,0424489
0,7 1,243 0,0346028
0,8 1,032 0,0287118
0,9 0,871 0,0242342
1 0,746 0,0207684
1,2 0,569 0,0158414
1,4 0,452 0,0125726
1,6 0,370 0,0102833
1,8 0,309 0,0086100
2 0,264 0,0073445
2,2 0,229 0,0063606
2,4 0,200 0,0055780
2,6 0,178 0,0049435
2,8 0,159 0,0044208
3 0,143 0,0039840
3,2 0,130 0,0036147
3,4 0,119 0,0032992
3,6 0,109 0,0030270
3,8 0,100 0,0027903
4 0,093 0,0025829
4,2 0,086 0,0024000
4,4 0,080 0,0022377
33
GRAFICO 3.1: Espectro de diseño Edificio Mixto, para suelo II, zonificación sísmica 2,
categoría C.
0,08
0,07
0,06
0,05
Sa / g
0,04
0,03
0,02
0,01
0,00
0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5
Tn (s)
GRAFICO 3.2: Espectro de diseño Edificio Acero, para suelo II, zonificación sísmica 2,
categoría C.
0,08
0,07
0,06
0,05
Sa / g
0,04
0,03
0,02
0,01
0,00
0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5
Tn (s)
34
3.3 ESTRUCTURACIONES, PLANTAS Y ELEVACIONES
Elevaciones
Elevación
idénticas
1 2, 6, 7
3 5
A B, G, H
C F
35
3.4 MODELACIÓN ESTRUCTURAL
3.4.1 GENERALIDADES
Fue escogido, ya que en los últimos 20 años, ETABS© ha sido reconocido como
el estándar internacional para el Diseño y Análisis de Edificios y tiene entre sus logros
el diseño de la mayoría de estructuras importantes alrededor del mundo. El software
es también internacionalmente usado como una herramienta educativa y de
investigación en muchas instituciones académicas. Actualmente, la nueva versión del
ETABS está totalmente integrada, realiza análisis basado en objetos, diseña,
optimiza y dibuja.
Posee una interfase gráfica basada en objetos, que la hace versátil y fácil de
utilizar, potenciada por nuevas técnicas numéricas la que permite crear diseños
completos, elaborando planos y cuantificando materiales para la construcción con
acero, sin estar limitado por el tamaño del elemento y satisfaciendo los requerimientos
de estabilidad, rigidez y deformación. Los nuevos métodos de análisis del ETABS©
resuelven muchos aspectos del diseño de edificios en los cuales los Ingenieros
Estructurales se han esforzado por mucho tiempo, tales como: Cálculo del Diagrama
de Esfuerzo Cortante en Losas y envolvente de fuerzas, Modelación de Estructuras de
Estacionamientos, Rampas rectas y curvas, Modelación de deformación en zonas de
juntas, Efectos de secuencia de carga durante el proceso constructivo. El modelo
integrado puede incluir Pórticos resistentes a momentos, brazos rígidos, sistemas
reticulados, pórticos con secciones reducidas de vigas, placas laterales, losas rígidas
y flexibles, Techos inclinados, Rampas y estructuras de estacionamiento, edificios con
torres múltiples y sistemas de diafragmas conectados con sistemas complejos de
pisos, compuestos o de acero, etc.
Copyright 1984-2002 Computers and Structures Inc.
49
3.4.2 MODELACIÓN
Se creo un sistema de malla de tres pisos más una base, se crearon las tres
plantas principales, o de pisos maestros, que sirvieron de base para las otras 27, las del
piso 1, 10 y 11. Las otras plantas se generaron a partir de éstas, quedando una sistema
con 30 pisos más una base. Así, sólo fue necesario trabajar en base a las tres plantas
principales, las que al ser modificadas, modificaban sus plantas similares
automáticamente.
50
2
FIGURA 3.7: Areas tributarias de losas. Los números representan la superficie en m .
Así, cada viga recibe el aporte de su losa, peso propio y sobrecarga, además
del muro cortina en el caso de las vigas de la periferia, quedando repartidas de la
siguiente manera:
51
TABLA 3.6: Carga sobre vigas debido a Peso propio de losas, muro cortina y Sobrecarga,
Edificio Acero:
52
A1 A2 Viga Lviga elosa Qlosa Qmuro Qtotal Qsc
Viga 2 2
(m ) (m ) Borde (m) (m) (Kg/m) (Kg/m) (Kg/m) (kg/m)
46 3,95 0 NO 3,7 0,15 400 400 267
47 3,17 0 NO 7,5 0,15 159 159 106
48 3,17 0 NO 7,5 0,15 159 159 106
49 0,85 0,54 NO 1,3 0,15 401 401 267
50 0,85 0,54 NO 1,3 0,15 401 401 267
51 11,1 10,07 NO 6 0,15 1323 1323 882
52 9 7,64 NO 6 0,15 1040 1040 693
53 13,72 5,5 NO 7,5 0,15 961 961 641
54 13,72 5,5 NO 7,5 0,15 961 961 641
55 9 7,64 NO 6 0,15 1040 1040 693
56 11,1 10,07 NO 6 0,15 1323 1323 882
57 4,57 0 Si 5 0,15 343 435 778 229
58 7,92 7,9 NO 5 0,15 1187 1187 791
59 7,92 7,9 NO 5 0,15 1187 1187 791
60 7,92 7,9 NO 5 0,15 1187 1187 791
61 7,92 7,9 NO 5 0,15 1187 1187 791
62 4,57 0 Si 5 0,15 343 435 778 229
63 6,41 0 Si 6 0,15 401 435 836 267
64 5,2 0 Si 6 0,15 325 435 760 217
65 7,93 0 Si 7,5 0,15 397 435 832 264
66 7,93 0 Si 7,5 0,15 397 435 832 264
67 5,2 0 Si 6 0,15 325 435 760 217
68 6,41 0 Si 6 0,15 401 435 836 267
Donde,
Losa Losa
A1 A2 Lviga
Viga
53
Tabla 3.7: Carga sobre vigas y muros debido a Peso propio de losas, muro cortina y
Sobrecarga, Edificio Mixto:
54
A1 A2 Viga Lviga elosa Qlosa Qborde Q Qtotal Qsc
Viga 2 2 2
(m ) (m ) Borde (m) (m) (Kg/m) (Kg/m) (Kg/m ) (Kg/m) (kg/m)
38 3,95 0 No 3,7 0,15 400 400 267
W14 1,585 0 No 3,75 0,15 159 55 106
W15 1,585 0 No 3,75 0,15 159 55 106
W16 1,585 0 No 3,75 0,15 159 55 106
W17 1,585 0 No 3,75 0,15 159 55 106
39 0,85 0,54 No 1,3 0,15 401 401 267
40 0,85 0,54 No 1,3 0,15 401 401 267
41 11,1 10,07 No 6 0,15 1323 1323 882
42 9 7,64 No 6 0,15 1040 1040 693
43 13,72 5,5 No 7,5 0,15 961 961 641
44 13,72 5,5 No 7,5 0,15 961 961 641
45 9 7,64 No 6 0,15 1040 1040 693
46 11,1 10,07 No 6 0,15 1323 1323 882
47 4,57 0 Si 5 0,15 343 435 778 229
48 7,92 7,9 No 5 0,15 1187 1187 791
49 7,92 7,9 No 5 0,15 1187 1187 791
50 7,92 7,9 No 5 0,15 1187 1187 791
51 7,92 7,9 No 5 0,15 1187 1187 791
52 4,57 0 Si 5 0,15 343 435 778 229
53 6,41 0 Si 6 0,15 401 435 836 267
54 5,2 0 Si 6 0,15 325 435 760 217
55 7,93 0 Si 7,5 0,15 397 435 832 264
56 7,93 0 Si 7,5 0,15 397 435 832 264
57 5,2 0 Si 6 0,15 325 435 760 217
58 6,41 0 Si 6 0,15 401 435 836 267
Donde,
Losa Losa
A1 A2 Lviga
Viga
55
3.4.2.2 Diafragma Rígido
Cada piso fue considerado como diafragma rígido mediante la opción asign
rigid diaphragm, uniendo cada punto de cada planta a un diafragma llamado D1, el
programa calcula automáticamente el centro de masa y rigidez de cada uno de estos
diafragmas.
Se crearon cuatro estados de carga estáticos: PP, SC, VX, VY, SMX y SMY
que corresponden a estados de carga muerta (peso propio), carga viva (sobrecarga
de uso), viento en X, viento en Y, sismo en X y sismo en Y, respectivamente. Además
se crearon dos estados de carga dinámicos o de espectros de respuestas, que son SX
y SY, que corresponden al sismo en X y a sismo en Y, respectivamente.
Para el caso PP, se consideró el cálculo del peso propio de los elementos en
forma automática por el programa y se agregó en forma manual, en este estado de
carga, el peso de las losas a las vigas y muros de los pisos y el peso del muro cortina
a las vigas de la periferia.
56
TABLA 3.8: Presión debida al viento
2
Piso h (m) q (kg/m ) Fx (Kg) Fy (Kg)
30 87,0 125,8 4378 6895
29 84,1 124,6 8675 13663
28 81,2 123,5 8594 13536
27 78,3 122,3 8513 13409
26 75,4 121,2 8433 13282
25 72,5 119,7 8331 13122
24 69,6 118,2 8226 12956
23 66,7 116,7 8121 12791
22 63,8 115,2 8016 12626
21 60,9 113,7 7911 12460
20 58,0 112,2 7806 12295
19 55,1 110,7 7701 12130
18 52,2 109,1 7596 11964
17 49,3 107,7 7492 11801
16 46,4 106,2 7392 11642
15 43,5 104,8 7291 11483
14 40,6 103,3 7190 11324
13 37,7 101,2 7041 11089
12 34,8 98,8 6879 10835
11 31,9 96,5 6718 10581
10 29,0 94,0 6542 10304
9 26,1 91,1 6341 9986
8 23,2 88,2 6139 9668
7 20,3 85,3 5937 9351
6 17,4 79,8 5554 8748
5 14,5 74,3 5174 8148
4 11,6 70,5 4904 7725
3 8,7 66,6 4635 7301
2 5,8 62,7 4366 6877
1 2,9 58,9 4097 6453
Donde,
= 1.2
FxFx = 1.2
× q××q 20
× 20
× 2.9
× 2.9 Para pisos 1 a 29
FyFy= 1.2
= 1.2
× q××q 31.5
× 31.5
× 2.9
× 2.9
Fx = 1.2 × q × 20 × 1.45
Fy = 1.2 × q × 31.5 × 1.45 Para piso 30
57
Los casos SMX y SMY corresponden a los momentos estáticos debido a la
torsión accidental, los que fueron calculados a partir de los esfuerzos de corte de cada
nivel entregados por el programa para los estados de carga de espectro de respuesta
SX y SY, de la siguiente manera:
Edificio Mixto:
VX FiX Zk e MZ
Nivel
(kg) (kg) (m) (m) (kg m)
PISO 30 94422 94422 87 2,00 188844
PISO 29 189782 95360 84,1 1,93 184363
PISO 28 257731 67949 81,2 1,87 126838
PISO 27 300373 42642 78,3 1,80 76755
PISO 26 321400 21027 75,4 1,73 36446
PISO 25 325929 4530 72,5 1,67 7550
PISO 24 319983 5946 69,6 1,60 9514
PISO 23 309584 10400 66,7 1,53 15946
PISO 22 299591 9993 63,8 1,47 14656
PISO 21 292699 6891 60,9 1,40 9648
PISO 20 289379 3320 58 1,33 4427
PISO 19 289386 7 55,1 1,27 9
PISO 18 291794 2407 52,2 1,20 2889
PISO 17 295892 4098 49,3 1,13 4645
PISO 16 301611 5719 46,4 1,07 6100
PISO 15 309276 7665 43,5 1,00 7665
PISO 14 319427 10151 40,6 0,93 9474
PISO 13 332866 13439 37,7 0,87 11647
PISO 12 350761 17895 34,8 0,80 14316
PISO 11 374476 23715 31,9 0,73 17391
PISO 10 406030 31554 29 0,67 21036
PISO 9 446067 40038 26,1 0,60 24023
PISO 8 491924 45856 23,2 0,53 24457
PISO 7 540318 48395 20,3 0,47 22584
PISO 6 587284 46966 17,4 0,40 18786
PISO 5 628910 41625 14,5 0,33 13875
PISO 4 662055 33145 11,6 0,27 8839
PISO 3 684940 22885 8,7 0,20 4577
PISO 2 697562 12623 5,8 0,13 1683
PISO 1 701838 4276 2,9 0,07 285
58
TABLA 3.10: momentos estáticos por torsión accidental para sismo en
dirección Y, Edificio Mixto.
VY FiY Zk e MZ
Nivel
(kg) (kg) (m) (m) (kg m)
PISO 30 82647 82647 87 3,15 260338
PISO 29 170767 88120 84,1 3,045 268325
PISO 28 237900 67133 81,2 2,94 197372
PISO 27 284434 46534 78,3 2,835 131923
PISO 26 312235 27802 75,4 2,73 75898
PISO 25 324518 12283 72,5 2,625 32242
PISO 24 325421 903 69,6 2,52 2275
PISO 23 319347 6073 66,7 2,415 14667
PISO 22 310195 9152 63,8 2,31 21142
PISO 21 300720 9475 60,9 2,205 20893
PISO 20 292277 8442 58 2,1 17729
PISO 19 286485 5792 55,1 1,995 11555
PISO 18 284082 2404 52,2 1,89 4543
PISO 17 285332 1250 49,3 1,785 2231
PISO 16 290583 5251 46,4 1,68 8822
PISO 15 300118 9536 43,5 1,575 15019
PISO 14 314003 13885 40,6 1,47 20410
PISO 13 332120 18117 37,7 1,365 24730
PISO 12 354372 22251 34,8 1,26 28037
PISO 11 380819 26448 31,9 1,155 30547
PISO 10 412603 31784 29 1,05 33373
PISO 9 450399 37795 26,1 0,945 35716
PISO 8 492300 41902 23,2 0,84 35198
PISO 7 536321 44021 20,3 0,735 32355
PISO 6 579822 43501 17,4 0,63 27406
PISO 5 619865 40043 14,5 0,525 21022
PISO 4 653676 33811 11,6 0,42 14201
PISO 3 679117 25441 8,7 0,315 8014
PISO 2 695097 15979 5,8 0,21 3356
PISO 1 701839 6742 2,9 0,105 708
Donde:
VX FiX Zk e MZ
Nivel
(kg) (kg) (m) (m) (kg m)
PISO 30 75613 75613 87 2,00 151225
PISO 29 151782 76169 84,1 1,93 147261
PISO 28 210614 58832 81,2 1,87 109820
PISO 27 251128 40514 78,3 1,80 72926
PISO 26 273616 22487 75,4 1,73 38978
PISO 25 279831 6215 72,5 1,67 10358
PISO 24 273151 6680 69,6 1,60 10688
PISO 23 258623 14528 66,7 1,53 22276
PISO 22 242687 15936 63,8 1,47 23373
PISO 21 231980 10707 60,9 1,40 14990
PISO 20 230897 1083 58 1,33 1444
PISO 19 240074 9177 55,1 1,27 11624
PISO 18 255612 15538 52,2 1,20 18645
PISO 17 272150 16538 49,3 1,13 18743
PISO 16 285341 13191 46,4 1,07 14070
PISO 15 292821 7480 43,5 1,00 7480
PISO 14 294459 1638 40,6 0,93 1529
PISO 13 292364 2096 37,7 0,87 1816
PISO 12 290644 1720 34,8 0,80 1376
PISO 11 294476 3832 31,9 0,73 2810
PISO 10 308449 13973 29 0,67 9316
PISO 9 334518 26069 26,1 0,60 15641
PISO 8 370294 35776 23,2 0,53 19080
PISO 7 411443 41149 20,3 0,47 19203
PISO 6 453261 41819 17,4 0,40 16727
PISO 5 491648 38387 14,5 0,33 12796
PISO 4 523506 31858 11,6 0,27 8495
PISO 3 546885 23379 8,7 0,20 4676
PISO 2 561054 14169 5,8 0,13 1889
PISO 1 566523 5469 2,9 0,07 365
60
TABLA 3.12: momentos estáticos por torsión accidental para sismo en
dirección Y, Edificio Acero.
VY FiY Zk e MZ
Nivel
(kg) (kg) (m) (m) (kg m)
PISO 30 68411 68411 87 3,15 215495
PISO 29 142398 73987 84,1 3,05 225290
PISO 28 204802 62404 81,2 2,94 183469
PISO 27 253514 48711 78,3 2,84 138097
PISO 26 287531 34017 75,4 2,73 92867
PISO 25 307186 19655 72,5 2,63 51594
PISO 24 314278 7092 69,6 2,52 17872
PISO 23 312068 2210 66,7 2,42 5337
PISO 22 305019 7049 63,8 2,31 16283
PISO 21 298080 6939 60,9 2,21 15299
PISO 20 295439 2642 58 2,10 5548
PISO 19 299623 4184 55,1 2,00 8347
PISO 18 309740 10118 52,2 1,89 19122
PISO 17 322821 13081 49,3 1,79 23349
PISO 16 335382 12561 46,4 1,68 21102
PISO 15 344682 9300 43,5 1,58 14647
PISO 14 349436 4754 40,6 1,47 6989
PISO 13 350112 676 37,7 1,37 923
PISO 12 348923 1189 34,8 1,26 1499
PISO 11 349434 511 31,9 1,16 590
PISO 10 355743 6309 29 1,05 6624
PISO 9 371092 15349 26,1 0,94 14505
PISO 8 395626 24534 23,2 0,84 20608
PISO 7 427122 31496 20,3 0,73 23150
PISO 6 461889 34766 17,4 0,63 21903
PISO 5 495867 33979 14,5 0,52 17839
PISO 4 525426 29558 11,6 0,42 12414
PISO 3 547806 22380 8,7 0,31 7050
PISO 2 561457 13651 5,8 0,21 2867
PISO 1 566523 5066 2,9 0,10 532
Donde:
61
Para crear los estados de carga: SX y SY, se ingresó el espectro de respuesta
para cada edificio mediante archivo de entrada de texto externo, el que poseía los
datos del espectro en forma de coordenadas (período, aceleración).
Edificio Acero
DSTL1 1,4 PP
DSTL2 1,2 PP + 1,6 SC
DSTL3 1,2 PP + 0,5 SC + 1,3 VX
DSTL4 1,2 PP + 0,5 SC - 1,3 VX
DSTL5 1,2 PP + 0,5 SC + 1,3 VY
DSTL6 1,2 PP + 0,5 SC - 1,3 VY
DSTL7 0,9 PP + 1,3 VX
DSTL8 0,9 PP - 1,3 VX
DSTL9 0,9 PP + 1,3 VY
DSTL10 0,9 PP - 1,3 VY
COMB1 1,2 PP + 0,8 VX
COMB2 1,2 PP - 0,8 VX
COMB3 1,2 PP + 0,8 VY
COMB4 1,2 PP - 0,8 VY
COMB5 1,4 PP + 1,4 SC + 1,4 SX + 1,4 SMX
COMB6 0,9 PP + 1,4 SX + 1,4 SMX
COMB7 1,4 PP + 1,4 SC + 1,4 SY + 1,4 SMY
COMB8 0,9 PP + 1,4 SY + 1,4 SMY
COMB13 SX + SMX
COMB14 SY + SMY
COMB15 PP + SX + SMX
COMB16 PP + SY + SMY
COMB17 0,75 (PP + SC + SX + SMX)
COMB18 0,75 (PP + SC + SY + SMY)
62
Edificio Mixto:
DSTL1 1,4 PP
DSTL2 1,2 PP + 1,6 SC
DSTL3 1,2 PP + 0,5 SC + 1,3 VX
DSTL4 1,2 PP + 0,5 SC - 1,3 VX
DSTL5 1,2 PP + 0,5 SC + 1,3 VY
DSTL6 1,2 PP + 0,5 SC - 1,3 VY
DSTL7 0,9 PP + 1,3 VX
DSTL8 0,9 PP - 1,3 VX
DSTL9 0,9 PP + 1,3 VY
DSTL10 0,9 PP - 1,3 VY
DCON2 1,4 PP + 1,7 SC
DCON3 0,75 ( 1,4 PP + 1,7 SC + 1,7 VX )
DCON4 0,75 ( 1,4 PP + 1,7 SC - 1,7 VX )
DCON5 0,75 ( 1,4 PP + 1,7 SC + 1,7 VY )
DCON6 0,75 ( 1,4 PP + 1,7 SC - 1,7 VY )
COMB1 1,2 PP + 0,8 VX
COMB2 1,2 PP - 0,8 VX
COMB3 1,2 PP + 0,8 VY
COMB4 1,2 PP - 0,8 VY
COMB5 1,4 PP + 1,4 SC + 1,4 (SX + SMX)
COMB6 0,9 PP + 1,4 (SX + SMX)
COMB7 1,4 PP + 1,4 SC + 1,4 (SY + SMY)
COMB8 0,9 PP + 1,4 (SY + SMY)
COMB9 0,75 ( 1,4 PP + 1,7 SC + 1,87 (SX + SMX))
COMB10 0,75 ( 1,4 PP + 1,7 SC + 1,87 (SY + SMY))
COMB11 0,9 PP + 1,43 (SX + SMX)
COMB12 0,9 PP + 1,43 (SY + SMY)
COMB13 SX + SMX
COMB14 SY + SMY
COMB15 PP + SX + SMX
COMB16 PP + SY + SMY
COMB17 0,75 (PP + SC + SX + SMX)
COMB18 0,75 (PP + SC + SY + SMY)
63
3.4.2.5 Fuentes de masa
Las masas sísmicas fueron calculadas automáticamente por el programa a partir
de las cargas del estado PP y de un 25% del estado SC.
Se consideró un análisis tridimensional, esto es en UX, UY, UZ, RX, RY, y RZ.
En el análisis dinámico se incluyeron 15 modos para Edificio Mixto y 10 modos para
edificio Acero para alcanzar el 90% de la masa total exigida por la norma NCh433Of96,
como se verá más adelante. No se incluyó análisis P- Δ.
3.4.2.8 Modelos
Copyright 1984-2002 Computers and Structures Inc.
64
,
ETABS
tf
e
H
H
tw
B
B
Vigas:
H 30 cm
B 20 cm
69
CAPITULO IV
La tabla 4.1 se dan a conocer los datos más relevantes del edificio, como son la
masa sísmica por piso y la suma de ésta, las coordenadas del centro de masa y rigidez.
71
Donde:
Masa = Masa en X e Y de cada piso
XCM = centro de masa en la dirección X medido en metros a partir del eje 1
YCM = centro de masa en la dirección Y medido en metros a partir del eje A
XCR = centro de rigidez en la dirección X medido en metros a partir del eje 1
YCR = centro de rigidez en la dirección Y medido en metros a partir del eje A
72
4.1.1.1 Resultados principales del Análisis Dinámico.
73
4.1.1.2 Análisis Dinámico Global en la dirección X:
74
4.1.1.3 Análisis Dinámico Global en la dirección Y:
75
TABLA 4.5: Corte, volcante y torsión combinados, por nivel, para sismo en dirección X
VX MY T
Nivel
(kg) (kg m) (kg m)
PISO 30 94422 273824 1171716
PISO 29 189782 823929 2359752
PISO 28 257731 1569990 3207671
PISO 27 300373 2436546 3743115
PISO 26 321400 3356760 4013105
PISO 25 325929 4275602 4080956
PISO 24 319983 5151773 4038591
PISO 23 309584 5957979 3952051
PISO 22 299591 6679501 3865123
PISO 21 292699 7311463 3805601
PISO 20 289379 7851733 3781610
PISO 19 289386 8301335 3791331
PISO 18 291794 8666418 3828135
PISO 17 295892 8952948 3878004
PISO 16 301611 9166723 3937310
PISO 15 309276 9313842 4011602
PISO 14 319427 9401457 4112656
PISO 13 332866 9438832 4255558
PISO 12 350761 9439034 4456559
PISO 11 374476 9421457 4730087
PISO 10 406030 9411799 5095036
PISO 9 446067 9449248 5553519
PISO 8 491924 9589053 6071161
PISO 7 540318 9892078 6608854
PISO 6 587284 10411677 7122352
PISO 5 628910 11178901 7570208
PISO 4 662055 12194429 7921273
PISO 3 684940 13431739 8160092
PISO 2 697562 14848376 8289947
PISO 1 701838 16398909 8333141
76
TABLA 4.6: Corte, volcante y torsión combinados, por nivel, para sismo en dirección Y
VY MX T
Nivel
(kg) (kg m) (kg m)
PISO 30 82647 239676 1562037
PISO 29 170767 734765 3218236
PISO 28 237900 1423899 4472957
PISO 27 284434 2245986 5337792
PISO 26 312235 3143909 5851561
PISO 25 324518 4067804 6077262
PISO 24 325421 4977329 6093750
PISO 23 319347 5842562 6012763
PISO 22 310195 6643503 5889740
PISO 21 300720 7368459 5761417
PISO 20 292277 8008667 5646180
PISO 19 286485 8559437 5566498
PISO 18 284082 9022430 5533200
PISO 17 285332 9401237 5555107
PISO 16 290583 9701323 5646629
PISO 15 300118 9930334 5811837
PISO 14 314003 10098573 6050927
PISO 13 332120 10219548 6361006
PISO 12 354372 10310675 6739517
PISO 11 380819 10394186 7186609
PISO 10 412603 10495571 7720582
PISO 9 450399 10648282 8351565
PISO 8 492300 10895315 9046715
PISO 7 536321 11281690 9772398
PISO 6 579822 11847151 10484946
PISO 5 619865 12617880 11136644
PISO 4 653676 13600815 11683365
PISO 3 679117 14783178 12092077
PISO 2 695097 16137019 12347099
PISO 1 701839 17626438 12453992
77
4.1.2 EDIFICIO ACERO
La tabla 4.7 se dan a conocer los datos más relevantes del edificio, como son la
masa sísmica por piso y la suma de ésta, las coordenadas del centro de masa y rigidez.
78
Donde:
Masa = Masa de cada piso
XCM = centro de masa en la dirección X medido en metros a partir del eje 1
YCM = centro de masa en la dirección Y medido en metros a partir del eje A
XCR = centro de rigidez en la dirección X medido en metros a partir del eje 1
YCR = centro de rigidez en la dirección Y medido en metros a partir del eje A
79
4.1.2.1 Resultados principales del Análisis Dinámico.
80
4.1.2.2 Análisis Dinámico Global en la dirección X:
81
4.1.2.3 Análisis Dinámico Global en la dirección Y:
82
TABLA 4.10: Corte, volcante y torsión combinados, por nivel, para sismo en dirección X
VX MY T
Nivel
(kg) (kg m) (kg m)
PISO 30 75613 219277 973680
PISO 29 151782 659394 1963814
PISO 28 210614 1269862 2728862
PISO 27 251128 1996939 3254585
PISO 26 273616 2786860 3544087
PISO 25 279831 3589300 3620781
PISO 24 273151 4360788 3551842
PISO 23 258623 5067677 3406458
PISO 22 242687 5688304 3247881
PISO 21 231980 6213895 3140826
PISO 20 230897 6646646 3125345
PISO 19 240074 6998137 3227405
PISO 18 255612 7287325 3396897
PISO 17 272150 7534761 3566954
PISO 16 285341 7758135 3687024
PISO 15 292821 7968848 3733738
PISO 14 294459 8170758 3712089
PISO 13 292364 8361727 3658617
PISO 12 290644 8537571 3625296
PISO 11 294476 8697251 3675345
PISO 10 308449 8846928 3861192
PISO 9 334518 9004315 4193071
PISO 8 370294 9200573 4629876
PISO 7 411443 9475767 5115228
PISO 6 453261 9871501 5594986
PISO 5 491648 10421175 6025800
PISO 4 523506 11141608 6376890
PISO 3 546885 12029824 6630697
PISO 2 561054 13065992 6782488
PISO 1 566523 14220376 6840361
83
TABLA 4.11: Corte, volcante y torsión combinados, por nivel, para sismo en dirección Y
VY MX T
Nivel
(kg) (kg m) (kg m)
PISO 30 68411 198392 1292965
PISO 29 142398 611319 2683555
PISO 28 204802 1205053 3849899
PISO 27 253514 1939437 4755188
PISO 26 287531 2770749 5383840
PISO 25 307186 3655007 5744992
PISO 24 314278 4551398 5874554
PISO 23 312068 5425451 5845081
PISO 22 305019 6251600 5750334
PISO 21 298080 7014735 5656379
PISO 20 295439 7709719 5620299
PISO 19 299623 8341521 5694575
PISO 18 309740 8922343 5873026
PISO 17 322821 9467230 6102391
PISO 16 335382 9990620 6321330
PISO 15 344682 10503414 6482445
PISO 14 349436 11011417 6564322
PISO 13 350112 11515616 6575902
PISO 12 348923 12014184 6558670
PISO 11 349434 12505556 6567306
PISO 10 355743 12990996 6673298
PISO 9 371092 13477698 6929559
PISO 8 395626 13980496 7336581
PISO 7 427122 14519896 7855770
PISO 6 461889 15119207 8425256
PISO 5 495867 15800394 8978247
PISO 4 525426 16579673 9456226
PISO 3 547806 17464137 9815769
PISO 2 561457 18450526 10033630
PISO 1 566523 19526802 10113953
84
4.2 DEFORMACIONES
Sismo en dirección X
COMB13 SX + SMX
COMB15 PP + SX + SMX
COMB17 0,75 (PP + SC + SX + SMX)
Sismo en dirección Y
COMB14 SY + SMY
COMB16 PP + SY + SMY
COMB18 0,75 (PP + SC + SY + SMY)
85
4.2.1 EDIFICIO MIXTO
Nivel Combinación
UX RZ Δ UX ΔRZ
(m) (rad) (m) (rad)
PISO 30 COMB13 MAX 0,0627 0,00306 0,0030 0,00007
PISO 30 COMB13 MIN -0,0614 0,00153 -0,0028 0,00005
PISO 30 COMB15 MAX 0,0627 0,00306 0,0030 0,00007
PISO 30 COMB15 MIN -0,0614 0,00153 -0,0028 0,00005
PISO 30 COMB17 MAX 0,0471 0,00229 0,0023 0,00005
PISO 30 COMB17 MIN -0,0460 0,00114 -0,0020 0,00003
PISO 29 COMB13 MAX 0,0597 0,00299 0,0029 0,00007
PISO 29 COMB13 MIN -0,0586 0,00148 -0,0028 0,00005
PISO 29 COMB15 MAX 0,0597 0,00299 0,0029 0,00007
PISO 29 COMB15 MIN -0,0586 0,00148 -0,0028 0,00005
PISO 29 COMB17 MAX 0,0448 0,00224 0,0022 0,00005
PISO 29 COMB17 MIN -0,0440 0,00111 -0,0022 0,00003
PISO 28 COMB13 MAX 0,0568 0,00292 0,0028 0,00009
PISO 28 COMB13 MIN -0,0558 0,00143 -0,0029 0,00005
PISO 28 COMB15 MAX 0,0568 0,00292 0,0028 0,00009
PISO 28 COMB15 MIN -0,0558 0,00143 -0,0029 0,00005
PISO 28 COMB17 MAX 0,0426 0,00219 0,0021 0,00007
PISO 28 COMB17 MIN -0,0418 0,00108 -0,0021 0,00005
PISO 27 COMB13 MAX 0,0540 0,00283 0,0028 0,00009
PISO 27 COMB13 MIN -0,0529 0,00138 -0,0027 0,00006
PISO 27 COMB15 MAX 0,0540 0,00283 0,0028 0,00009
PISO 27 COMB15 MIN -0,0529 0,00138 -0,0027 0,00006
PISO 27 COMB17 MAX 0,0405 0,00212 0,0021 0,00007
PISO 27 COMB17 MIN -0,0397 0,00103 -0,0021 0,00004
PISO 26 COMB13 MAX 0,0512 0,00274 0,0027 0,00010
PISO 26 COMB13 MIN -0,0502 0,00132 -0,0027 0,00007
PISO 26 COMB15 MAX 0,0512 0,00274 0,0027 0,00010
PISO 26 COMB15 MIN -0,0502 0,00132 -0,0027 0,00007
PISO 26 COMB17 MAX 0,0384 0,00205 0,0020 0,00007
PISO 26 COMB17 MIN -0,0376 0,00099 -0,0020 0,00005
PISO 25 COMB13 MAX 0,0485 0,00264 0,0026 0,00010
PISO 25 COMB13 MIN -0,0475 0,00125 -0,0026 0,00006
PISO 25 COMB15 MAX 0,0485 0,00264 0,0026 0,00010
PISO 25 COMB15 MIN -0,0475 0,00125 -0,0026 0,00006
PISO 25 COMB17 MAX 0,0364 0,00198 0,0020 0,00008
PISO 25 COMB17 MIN -0,0356 0,00094 -0,0019 0,00005
PISO 24 COMB13 MAX 0,0459 0,00254 0,0026 0,00011
PISO 24 COMB13 MIN -0,0449 0,00119 -0,0026 0,00007
PISO 24 COMB15 MAX 0,0459 0,00254 0,0026 0,00011
PISO 24 COMB15 MIN -0,0449 0,00119 -0,0026 0,00007
PISO 24 COMB17 MAX 0,0344 0,0019 0,0019 0,00008
PISO 24 COMB17 MIN -0,0337 0,00089 -0,0019 0,00005
PISO 23 COMB13 MAX 0,0433 0,00243 0,0025 0,00011
PISO 23 COMB13 MIN -0,0423 0,00112 -0,0024 0,00006
PISO 23 COMB15 MAX 0,0433 0,00243 0,0025 0,00011
PISO 23 COMB15 MIN -0,0423 0,00112 -0,0024 0,00006
PISO 23 COMB17 MAX 0,0325 0,00182 0,0019 0,00008
PISO 23 COMB17 MIN -0,0318 0,00084 -0,0019 0,00005
PISO 22 COMB13 MAX 0,0408 0,00232 0,0024 0,00011
PISO 22 COMB13 MIN -0,0399 0,00106 -0,0024 0,00007
86
UX RZ ΔUX ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 22 COMB15 MAX 0,0408 0,00232 0,0024 0,00011
PISO 22 COMB15 MIN -0,0399 0,00106 -0,0024 0,00007
PISO 22 COMB17 MAX 0,0306 0,00174 0,0018 0,00008
PISO 22 COMB17 MIN -0,0299 0,00079 -0,0018 0,00005
PISO 21 COMB13 MAX 0,0384 0,00221 0,0024 0,00012
PISO 21 COMB13 MIN -0,0375 0,00099 -0,0023 0,00006
PISO 21 COMB15 MAX 0,0384 0,00221 0,0024 0,00012
PISO 21 COMB15 MIN -0,0375 0,00099 -0,0023 0,00006
PISO 21 COMB17 MAX 0,0288 0,00166 0,0018 0,00009
PISO 21 COMB17 MIN -0,0281 0,00074 -0,0017 0,00004
PISO 20 COMB13 MAX 0,0360 0,00209 0,0022 0,00011
PISO 20 COMB13 MIN -0,0352 0,00093 -0,0022 0,00006
PISO 20 COMB15 MAX 0,0360 0,00209 0,0022 0,00011
PISO 20 COMB15 MIN -0,0352 0,00093 -0,0022 0,00006
PISO 20 COMB17 MAX 0,0270 0,00157 0,0017 0,00008
PISO 20 COMB17 MIN -0,0264 0,0007 -0,0016 0,00005
PISO 19 COMB13 MAX 0,0338 0,00198 0,0023 0,00011
PISO 19 COMB13 MIN -0,0330 0,00087 -0,0022 0,00006
PISO 19 COMB15 MAX 0,0338 0,00198 0,0023 0,00011
PISO 19 COMB15 MIN -0,0330 0,00087 -0,0022 0,00006
PISO 19 COMB17 MAX 0,0253 0,00149 0,0016 0,00009
PISO 19 COMB17 MIN -0,0248 0,00065 -0,0017 0,00004
PISO 18 COMB13 MAX 0,0315 0,00187 0,0021 0,00011
PISO 18 COMB13 MIN -0,0308 0,00081 -0,0021 0,00005
PISO 18 COMB15 MAX 0,0315 0,00187 0,0021 0,00011
PISO 18 COMB15 MIN -0,0308 0,00081 -0,0021 0,00005
PISO 18 COMB17 MAX 0,0237 0,0014 0,0017 0,00008
PISO 18 COMB17 MIN -0,0231 0,00061 -0,0016 0,00004
PISO 17 COMB13 MAX 0,0294 0,00176 0,0022 0,00011
PISO 17 COMB13 MIN -0,0287 0,00076 -0,0021 0,00006
PISO 17 COMB15 MAX 0,0294 0,00176 0,0022 0,00011
PISO 17 COMB15 MIN -0,0287 0,00076 -0,0021 0,00006
PISO 17 COMB17 MAX 0,0220 0,00132 0,0016 0,00009
PISO 17 COMB17 MIN -0,0215 0,00057 -0,0016 0,00004
PISO 16 COMB13 MAX 0,0272 0,00165 0,0021 0,00012
PISO 16 COMB13 MIN -0,0266 0,0007 -0,0021 0,00005
PISO 16 COMB15 MAX 0,0272 0,00165 0,0021 0,00012
PISO 16 COMB15 MIN -0,0266 0,0007 -0,0021 0,00005
PISO 16 COMB17 MAX 0,0204 0,00123 0,0016 0,00008
PISO 16 COMB17 MIN -0,0199 0,00053 -0,0015 0,00005
PISO 15 COMB13 MAX 0,0251 0,00153 0,0021 0,00011
PISO 15 COMB13 MIN -0,0245 0,00065 -0,0021 0,00006
PISO 15 COMB15 MAX 0,0251 0,00153 0,0021 0,00011
PISO 15 COMB15 MIN -0,0245 0,00065 -0,0021 0,00006
PISO 15 COMB17 MAX 0,0188 0,00115 0,0016 0,00009
PISO 15 COMB17 MIN -0,0184 0,00048 -0,0016 0,00004
PISO 14 COMB13 MAX 0,0230 0,00142 0,0021 0,00012
PISO 14 COMB13 MIN -0,0224 0,00059 -0,0020 0,00005
PISO 14 COMB15 MAX 0,0230 0,00142 0,0021 0,00012
PISO 14 COMB15 MIN -0,0224 0,00059 -0,0020 0,00005
PISO 14 COMB17 MAX 0,0172 0,00106 0,0015 0,00008
PISO 14 COMB17 MIN -0,0168 0,00044 -0,0015 0,00004
PISO 13 COMB13 MAX 0,0209 0,0013 0,0021 0,00012
PISO 13 COMB13 MIN -0,0204 0,00054 -0,0021 0,00005
87
UX RZ ΔUX Δ RZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 13 COMB15 MAX 0,0209 0,0013 0,0021 0,00012
PISO 13 COMB15 MIN -0,0204 0,00054 -0,0021 0,00005
PISO 13 COMB17 MAX 0,0157 0,00098 0,0016 0,00009
PISO 13 COMB17 MIN -0,0153 0,0004 -0,0016 0,00004
PISO 12 COMB13 MAX 0,0188 0,00118 0,0021 0,00011
PISO 12 COMB13 MIN -0,0183 0,00049 -0,0020 0,00006
PISO 12 COMB15 MAX 0,0188 0,00118 0,0021 0,00011
PISO 12 COMB15 MIN -0,0183 0,00049 -0,0020 0,00006
PISO 12 COMB17 MAX 0,0141 0,00089 0,0016 0,00009
PISO 12 COMB17 MIN -0,0137 0,00036 -0,0015 0,00003
PISO 11 COMB13 MAX 0,0167 0,00107 0,0021 0,00012
PISO 11 COMB13 MIN -0,0163 0,00043 -0,0020 0,00005
PISO 11 COMB15 MAX 0,0167 0,00107 0,0021 0,00012
PISO 11 COMB15 MIN -0,0163 0,00043 -0,0020 0,00005
PISO 11 COMB17 MAX 0,0125 0,0008 0,0015 0,00009
PISO 11 COMB17 MIN -0,0122 0,00033 -0,0015 0,00004
PISO 10 COMB13 MAX 0,0146 0,00095 0,0020 0,00012
PISO 10 COMB13 MIN -0,0143 0,00038 -0,0020 0,00005
PISO 10 COMB15 MAX 0,0146 0,00095 0,0020 0,00012
PISO 10 COMB15 MIN -0,0143 0,00038 -0,0020 0,00005
PISO 10 COMB17 MAX 0,0110 0,00071 0,0016 0,00008
PISO 10 COMB17 MIN -0,0107 0,00029 -0,0015 0,00004
PISO 9 COMB13 MAX 0,0126 0,00083 0,0020 0,00011
PISO 9 COMB13 MIN -0,0123 0,00033 -0,0020 0,00005
PISO 9 COMB15 MAX 0,0126 0,00083 0,0020 0,00011
PISO 9 COMB15 MIN -0,0123 0,00033 -0,0020 0,00005
PISO 9 COMB17 MAX 0,0094 0,00063 0,0015 0,00009
PISO 9 COMB17 MIN -0,0092 0,00025 -0,0015 0,00004
PISO 8 COMB13 MAX 0,0106 0,00072 0,0020 0,00012
PISO 8 COMB13 MIN -0,0103 0,00028 -0,0019 0,00005
PISO 8 COMB15 MAX 0,0106 0,00072 0,0020 0,00012
PISO 8 COMB15 MIN -0,0103 0,00028 -0,0019 0,00005
PISO 8 COMB17 MAX 0,0079 0,00054 0,0014 0,00009
PISO 8 COMB17 MIN -0,0077 0,00021 -0,0014 0,00003
PISO 7 COMB13 MAX 0,0086 0,0006 0,0018 0,00011
PISO 7 COMB13 MIN -0,0084 0,00023 -0,0018 0,00004
PISO 7 COMB15 MAX 0,0086 0,0006 0,0018 0,00011
PISO 7 COMB15 MIN -0,0084 0,00023 -0,0018 0,00004
PISO 7 COMB17 MAX 0,0065 0,00045 0,0014 0,00008
PISO 7 COMB17 MIN -0,0063 0,00018 -0,0014 0,00004
PISO 6 COMB13 MAX 0,0068 0,00049 0,0018 0,00011
PISO 6 COMB13 MIN -0,0066 0,00019 -0,0017 0,00005
PISO 6 COMB15 MAX 0,0068 0,00049 0,0018 0,00011
PISO 6 COMB15 MIN -0,0066 0,00019 -0,0017 0,00005
PISO 6 COMB17 MAX 0,0051 0,00037 0,0013 0,00009
PISO 6 COMB17 MIN -0,0049 0,00014 -0,0012 0,00003
PISO 5 COMB13 MAX 0,0050 0,00038 0,0015 0,00011
PISO 5 COMB13 MIN -0,0049 0,00014 -0,0015 0,00004
PISO 5 COMB15 MAX 0,0050 0,00038 0,0015 0,00011
PISO 5 COMB15 MIN -0,0049 0,00014 -0,0015 0,00004
PISO 5 COMB17 MAX 0,0038 0,00028 0,0012 0,00007
PISO 5 COMB17 MIN -0,0037 0,00011 -0,0012 0,00003
PISO 4 COMB13 MAX 0,0035 0,00027 0,0014 0,00009
PISO 4 COMB13 MIN -0,0034 0,0001 -0,0014 0,00003
88
UX RZ Δ UX ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 4 COMB15 MAX 0,0035 0,00027 0,0014 0,00009
PISO 4 COMB15 MIN -0,0034 0,0001 -0,0014 0,00003
PISO 4 COMB17 MAX 0,0026 0,00021 0,0010 0,00008
PISO 4 COMB17 MIN -0,0025 0,00008 -0,0010 0,00003
PISO 3 COMB13 MAX 0,0021 0,00018 0,0010 0,00009
PISO 3 COMB13 MIN -0,0020 0,00007 -0,0010 0,00004
PISO 3 COMB15 MAX 0,0021 0,00018 0,0010 0,00009
PISO 3 COMB15 MIN -0,0020 0,00007 -0,0010 0,00004
PISO 3 COMB17 MAX 0,0016 0,00013 0,0008 0,00006
PISO 3 COMB17 MIN -0,0015 0,00005 -0,0007 0,00002
PISO 2 COMB13 MAX 0,0011 0,00009 0,0008 0,00006
PISO 2 COMB13 MIN -0,0010 0,00003 -0,0007 0,00002
PISO 2 COMB15 MAX 0,0011 0,00009 0,0008 0,00006
PISO 2 COMB15 MIN -0,0010 0,00003 -0,0007 0,00002
PISO 2 COMB17 MAX 0,0008 0,00007 0,0006 0,00005
PISO 2 COMB17 MIN -0,0008 0,00003 -0,0006 0,00002
PISO 1 COMB13 MAX 0,0003 0,00003 0,0003 0,00003
PISO 1 COMB13 MIN -0,0003 0,00001 -0,0003 0,00001
PISO 1 COMB15 MAX 0,0003 0,00003 0,0003 0,00003
PISO 1 COMB15 MIN -0,0003 0,00001 -0,0003 0,00001
PISO 1 COMB17 MAX 0,0002 0,00002 0,0002 0,00002
PISO 1 COMB17 MIN -0,0002 0,00001 -0,0002 0,00001
Donde:
89
TABLA 4.13 : Deformaciones para Sismo en dirección Y, Edificio Mixto.
Nivel Combinación
UY RZ ΔUY Δ RZ
(m) (rad) (m) (rad)
PISO 30 COMB14 MAX 0,0486 0,00355 0,0021 0,00008
PISO 30 COMB14 MIN -0,0486 0,00355 -0,0021 0,00008
PISO 30 COMB16 MAX 0,0486 0,00355 0,0021 0,00008
PISO 30 COMB16 MIN -0,0486 0,00355 -0,0021 0,00008
PISO 30 COMB18 MAX 0,0364 0,00266 0,0016 0,00006
PISO 30 COMB18 MIN -0,0365 0,00266 -0,0016 0,00006
PISO 29 COMB14 MAX 0,0465 0,00347 0,0022 0,00009
PISO 29 COMB14 MIN -0,0465 0,00347 -0,0022 0,00009
PISO 29 COMB16 MAX 0,0465 0,00347 0,0022 0,00009
PISO 29 COMB16 MIN -0,0465 0,00347 -0,0022 0,00009
PISO 29 COMB18 MAX 0,0348 0,0026 0,0016 0,00007
PISO 29 COMB18 MIN -0,0349 0,0026 -0,0016 0,00007
PISO 28 COMB14 MAX 0,0443 0,00338 0,0021 0,00011
PISO 28 COMB14 MIN -0,0443 0,00338 -0,0021 0,00011
PISO 28 COMB16 MAX 0,0443 0,00338 0,0021 0,00011
PISO 28 COMB16 MIN -0,0443 0,00338 -0,0021 0,00011
PISO 28 COMB18 MAX 0,0332 0,00253 0,0016 0,00008
PISO 28 COMB18 MIN -0,0333 0,00253 -0,0017 0,00008
PISO 27 COMB14 MAX 0,0422 0,00327 0,0021 0,00011
PISO 27 COMB14 MIN -0,0422 0,00327 -0,0021 0,00011
PISO 27 COMB16 MAX 0,0422 0,00327 0,0021 0,00011
PISO 27 COMB16 MIN -0,0422 0,00327 -0,0022 0,00011
PISO 27 COMB18 MAX 0,0316 0,00245 0,0016 0,00008
PISO 27 COMB18 MIN -0,0316 0,00245 -0,0016 0,00008
PISO 26 COMB14 MAX 0,0401 0,00316 0,0021 0,00013
PISO 26 COMB14 MIN -0,0401 0,00316 -0,0021 0,00013
PISO 26 COMB16 MAX 0,0401 0,00316 0,0021 0,00013
PISO 26 COMB16 MIN -0,04 0,00316 -0,0021 0,00013
PISO 26 COMB18 MAX 0,03 0,00237 0,0015 0,00010
PISO 26 COMB18 MIN -0,03 0,00237 -0,0015 0,00010
PISO 25 COMB14 MAX 0,038 0,00303 0,0021 0,00013
PISO 25 COMB14 MIN -0,038 0,00303 -0,0021 0,00013
PISO 25 COMB16 MAX 0,038 0,00303 0,002 0,00013
PISO 25 COMB16 MIN -0,0379 0,00303 -0,002 0,00013
PISO 25 COMB18 MAX 0,0285 0,00227 0,0015 0,00009
PISO 25 COMB18 MIN -0,0285 0,00227 -0,0016 0,00009
PISO 24 COMB14 MAX 0,0359 0,0029 0,002 0,00013
PISO 24 COMB14 MIN -0,0359 0,0029 -0,002 0,00013
PISO 24 COMB16 MAX 0,036 0,0029 0,002 0,00013
PISO 24 COMB16 MIN -0,0359 0,0029 -0,002 0,00013
PISO 24 COMB18 MAX 0,027 0,00218 0,0015 0,00010
PISO 24 COMB18 MIN -0,0269 0,00218 -0,0015 0,00010
PISO 23 COMB14 MAX 0,0339 0,00277 0,0019 0,00013
PISO 23 COMB14 MIN -0,0339 0,00277 -0,0019 0,00013
PISO 23 COMB16 MAX 0,034 0,00277 0,0019 0,00013
PISO 23 COMB16 MIN -0,0339 0,00277 -0,0019 0,00013
PISO 23 COMB18 MAX 0,0255 0,00208 0,0015 0,00010
PISO 23 COMB18 MIN -0,0254 0,00208 -0,0014 0,00010
PISO 22 COMB14 MAX 0,032 0,00264 0,0019 0,00014
PISO 22 COMB14 MIN -0,032 0,00264 -0,0019 0,00014
90
UY RZ Δ UY Δ RZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 22 COMB16 MAX 0,0321 0,00264 0,0019 0,00014
PISO 22 COMB16 MIN -0,032 0,00264 -0,0019 0,00014
PISO 22 COMB18 MAX 0,024 0,00198 0,0014 0,00010
PISO 22 COMB18 MIN -0,024 0,00198 -0,0014 0,00010
PISO 21 COMB14 MAX 0,0301 0,0025 0,0018 0,00013
PISO 21 COMB14 MIN -0,0301 0,0025 -0,0018 0,00013
PISO 21 COMB16 MAX 0,0302 0,0025 0,0018 0,00013
PISO 21 COMB16 MIN -0,0301 0,0025 -0,0018 0,00013
PISO 21 COMB18 MAX 0,0226 0,00188 0,0013 0,00010
PISO 21 COMB18 MIN -0,0226 0,00188 -0,0014 0,00010
PISO 20 COMB14 MAX 0,0283 0,00237 0,0017 0,00013
PISO 20 COMB14 MIN -0,0283 0,00237 -0,0017 0,00013
PISO 20 COMB16 MAX 0,0284 0,00237 0,0018 0,00013
PISO 20 COMB16 MIN -0,0283 0,00237 -0,0018 0,00013
PISO 20 COMB18 MAX 0,0213 0,00178 0,0013 0,00010
PISO 20 COMB18 MIN -0,0212 0,00178 -0,0013 0,00010
PISO 19 COMB14 MAX 0,0266 0,00224 0,0017 0,00013
PISO 19 COMB14 MIN -0,0266 0,00224 -0,0017 0,00013
PISO 19 COMB16 MAX 0,0266 0,00224 0,0017 0,00013
PISO 19 COMB16 MIN -0,0265 0,00224 -0,0017 0,00013
PISO 19 COMB18 MAX 0,02 0,00168 0,0013 0,00010
PISO 19 COMB18 MIN -0,0199 0,00168 -0,0013 0,00010
PISO 18 COMB14 MAX 0,0249 0,00211 0,0017 0,00014
PISO 18 COMB14 MIN -0,0249 0,00211 -0,0017 0,00014
PISO 18 COMB16 MAX 0,0249 0,00211 0,0017 0,00014
PISO 18 COMB16 MIN -0,0248 0,00211 -0,0017 0,00014
PISO 18 COMB18 MAX 0,0187 0,00158 0,0013 0,00010
PISO 18 COMB18 MIN -0,0186 0,00158 -0,0013 0,00010
PISO 17 COMB14 MAX 0,0232 0,00197 0,0017 0,00013
PISO 17 COMB14 MIN -0,0232 0,00197 -0,0017 0,00013
PISO 17 COMB16 MAX 0,0232 0,00197 0,0016 0,00013
PISO 17 COMB16 MIN -0,0231 0,00197 -0,0016 0,00013
PISO 17 COMB18 MAX 0,0174 0,00148 0,0012 0,00010
PISO 17 COMB18 MIN -0,0173 0,00148 -0,0012 0,00010
PISO 16 COMB14 MAX 0,0215 0,00184 0,0016 0,00013
PISO 16 COMB14 MIN -0,0215 0,00184 -0,0016 0,00013
PISO 16 COMB16 MAX 0,0216 0,00184 0,0017 0,00013
PISO 16 COMB16 MIN -0,0215 0,00184 -0,0016 0,00013
PISO 16 COMB18 MAX 0,0162 0,00138 0,0012 0,00010
PISO 16 COMB18 MIN -0,0161 0,00138 -0,0012 0,00010
PISO 15 COMB14 MAX 0,0199 0,00171 0,0016 0,00013
PISO 15 COMB14 MIN -0,0199 0,00171 -0,0016 0,00013
PISO 15 COMB16 MAX 0,0199 0,00171 0,0016 0,00013
PISO 15 COMB16 MIN -0,0199 0,00171 -0,0016 0,00013
PISO 15 COMB18 MAX 0,015 0,00128 0,0012 0,00009
PISO 15 COMB18 MIN -0,0149 0,00128 -0,0012 0,00009
PISO 14 COMB14 MAX 0,0183 0,00158 0,0016 0,00013
PISO 14 COMB14 MIN -0,0183 0,00158 -0,0016 0,00013
PISO 14 COMB16 MAX 0,0183 0,00158 0,0016 0,00013
PISO 14 COMB16 MIN -0,0183 0,00158 -0,0016 0,00013
PISO 14 COMB18 MAX 0,0138 0,00119 0,0012 0,00010
PISO 14 COMB18 MIN -0,0137 0,00119 -0,0012 0,00010
PISO 13 COMB14 MAX 0,0167 0,00145 0,0016 0,00013
PISO 13 COMB14 MIN -0,0167 0,00145 -0,0016 0,00013
91
UY RZ Δ UY Δ RZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 13 COMB16 MAX 0,0167 0,00145 0,0016 0,00013
PISO 13 COMB16 MIN -0,0167 0,00145 -0,0016 0,00013
PISO 13 COMB18 MAX 0,0126 0,00109 0,0012 0,00010
PISO 13 COMB18 MIN -0,0125 0,00109 -0,0012 0,00010
PISO 12 COMB14 MAX 0,0151 0,00132 0,0016 0,00014
PISO 12 COMB14 MIN -0,0151 0,00132 -0,0016 0,00014
PISO 12 COMB16 MAX 0,0151 0,00132 0,0016 0,00014
PISO 12 COMB16 MIN -0,0151 0,00132 -0,0016 0,00014
PISO 12 COMB18 MAX 0,0114 0,00099 0,0012 0,00010
PISO 12 COMB18 MIN -0,0113 0,00099 -0,0012 0,00010
PISO 11 COMB14 MAX 0,0135 0,00118 0,0016 0,00013
PISO 11 COMB14 MIN -0,0135 0,00118 -0,0016 0,00013
PISO 11 COMB16 MAX 0,0135 0,00118 0,0016 0,00013
PISO 11 COMB16 MIN -0,0135 0,00118 -0,0016 0,00013
PISO 11 COMB18 MAX 0,0102 0,00089 0,0012 0,00010
PISO 11 COMB18 MIN -0,0101 0,00089 -0,0012 0,00010
PISO 10 COMB14 MAX 0,0119 0,00105 0,0015 0,00013
PISO 10 COMB14 MIN -0,0119 0,00105 -0,0015 0,00013
PISO 10 COMB16 MAX 0,0119 0,00105 0,0015 0,00013
PISO 10 COMB16 MIN -0,0119 0,00105 -0,0015 0,00013
PISO 10 COMB18 MAX 0,009 0,00079 0,0012 0,00010
PISO 10 COMB18 MIN -0,0089 0,00079 -0,0011 0,00010
PISO 9 COMB14 MAX 0,0104 0,00092 0,0015 0,00013
PISO 9 COMB14 MIN -0,0104 0,00092 -0,0015 0,00013
PISO 9 COMB16 MAX 0,0104 0,00092 0,0015 0,00013
PISO 9 COMB16 MIN -0,0104 0,00092 -0,0016 0,00013
PISO 9 COMB18 MAX 0,0078 0,00069 0,0011 0,00010
PISO 9 COMB18 MIN -0,0078 0,00069 -0,0012 0,00010
PISO 8 COMB14 MAX 0,0089 0,00079 0,0015 0,00013
PISO 8 COMB14 MIN -0,0089 0,00079 -0,0015 0,00013
PISO 8 COMB16 MAX 0,0089 0,00079 0,0015 0,00013
PISO 8 COMB16 MIN -0,0088 0,00079 -0,0014 0,00013
PISO 8 COMB18 MAX 0,0067 0,00059 0,0012 0,00010
PISO 8 COMB18 MIN -0,0066 0,00059 -0,0011 0,00010
PISO 7 COMB14 MAX 0,0074 0,00066 0,0015 0,00013
PISO 7 COMB14 MIN -0,0074 0,00066 -0,0015 0,00013
PISO 7 COMB16 MAX 0,0074 0,00066 0,0015 0,00013
PISO 7 COMB16 MIN -0,0074 0,00066 -0,0015 0,00013
PISO 7 COMB18 MAX 0,0055 0,00049 0,001 0,00009
PISO 7 COMB18 MIN -0,0055 0,00049 -0,0011 0,00009
PISO 6 COMB14 MAX 0,0059 0,00053 0,0013 0,00012
PISO 6 COMB14 MIN -0,0059 0,00053 -0,0013 0,00012
PISO 6 COMB16 MAX 0,0059 0,00053 0,0013 0,00012
PISO 6 COMB16 MIN -0,0059 0,00053 -0,0013 0,00012
PISO 6 COMB18 MAX 0,0045 0,0004 0,0011 0,00009
PISO 6 COMB18 MIN -0,0044 0,0004 -0,001 0,00009
PISO 5 COMB14 MAX 0,0046 0,00041 0,0013 0,00011
PISO 5 COMB14 MIN -0,0046 0,00041 -0,0013 0,00011
PISO 5 COMB16 MAX 0,0046 0,00041 0,0013 0,00011
PISO 5 COMB16 MIN -0,0046 0,00041 -0,0013 0,00011
PISO 5 COMB18 MAX 0,0034 0,00031 0,0009 0,00009
PISO 5 COMB18 MIN -0,0034 0,00031 -0,0009 0,00009
PISO 4 COMB14 MAX 0,0033 0,0003 0,0011 0,00011
PISO 4 COMB14 MIN -0,0033 0,0003 -0,0011 0,00011
92
UY RZ ΔUY ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 4 COMB16 MAX 0,0033 0,0003 0,0011 0,00011
PISO 4 COMB16 MIN -0,0033 0,0003 -0,0011 0,00011
PISO 4 COMB18 MAX 0,0025 0,00022 0,0009 0,00008
PISO 4 COMB18 MIN -0,0025 0,00022 -0,0009 0,00008
PISO 3 COMB14 MAX 0,0022 0,00019 0,001 0,00009
PISO 3 COMB14 MIN -0,0022 0,00019 -0,001 0,00009
PISO 3 COMB16 MAX 0,0022 0,00019 0,001 0,00009
PISO 3 COMB16 MIN -0,0022 0,00019 -0,001 0,00009
PISO 3 COMB18 MAX 0,0016 0,00014 0,0007 0,00006
PISO 3 COMB18 MIN -0,0016 0,00014 -0,0007 0,00006
PISO 2 COMB14 MAX 0,0012 0,0001 0,0007 0,00007
PISO 2 COMB14 MIN -0,0012 0,0001 -0,0007 0,00007
PISO 2 COMB16 MAX 0,0012 0,0001 0,0007 0,00007
PISO 2 COMB16 MIN -0,0012 0,0001 -0,0007 0,00007
PISO 2 COMB18 MAX 0,0009 0,00008 0,0006 0,00006
PISO 2 COMB18 MIN -0,0009 0,00008 -0,0006 0,00006
PISO 1 COMB14 MAX 0,0005 0,00003 0,0005 0,00003
PISO 1 COMB14 MIN -0,0005 0,00003 -0,0005 0,00003
PISO 1 COMB16 MAX 0,0005 0,00003 0,0005 0,00003
PISO 1 COMB16 MIN -0,0005 0,00003 -0,0005 0,00003
PISO 1 COMB18 MAX 0,0003 0,00002 0,0003 0,00002
PISO 1 COMB18 MIN -0,0003 0,00002 -0,0003 0,00002
Donde:
93
4.2.2 EDIFICIO ACERO
UX RZ ΔUX ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 30 COMB13 MAX 0,0873 0,00302 0,0030 0,00007
PISO 30 COMB13 MIN -0,0859 0,00086 -0,0028 0,00005
PISO 30 COMB15 MAX 0,0873 0,00302 0,0030 0,00007
PISO 30 COMB15 MIN -0,0859 0,00086 -0,0028 0,00005
PISO 30 COMB17 MAX 0,0655 0,00226 0,0023 0,00005
PISO 30 COMB17 MIN -0,0644 0,00064 -0,0020 0,00003
PISO 29 COMB13 MAX 0,0838 0,00298 0,0029 0,00007
PISO 29 COMB13 MIN -0,0824 0,00084 -0,0028 0,00005
PISO 29 COMB15 MAX 0,0838 0,00298 0,0029 0,00007
PISO 29 COMB15 MIN -0,0824 0,00084 -0,0028 0,00005
PISO 29 COMB17 MAX 0,0629 0,00223 0,0022 0,00005
PISO 29 COMB17 MIN -0,0618 0,00063 -0,0022 0,00003
PISO 28 COMB13 MAX 0,0802 0,00292 0,0028 0,00009
PISO 28 COMB13 MIN -0,0789 0,00081 -0,0029 0,00005
PISO 28 COMB15 MAX 0,0802 0,00292 0,0028 0,00009
PISO 28 COMB15 MIN -0,0789 0,00081 -0,0029 0,00005
PISO 28 COMB17 MAX 0,0602 0,00219 0,0021 0,00007
PISO 28 COMB17 MIN -0,0592 0,00061 -0,0021 0,00005
PISO 27 COMB13 MAX 0,0766 0,00285 0,0028 0,00009
PISO 27 COMB13 MIN -0,0753 0,00077 -0,0027 0,00006
PISO 27 COMB15 MAX 0,0766 0,00285 0,0028 0,00009
PISO 27 COMB15 MIN -0,0753 0,00077 -0,0027 0,00006
PISO 27 COMB17 MAX 0,0575 0,00214 0,0021 0,00007
PISO 27 COMB17 MIN -0,0565 0,00058 -0,0021 0,00004
PISO 26 COMB13 MAX 0,073 0,00277 0,0027 0,0001
PISO 26 COMB13 MIN -0,0717 0,00073 -0,0027 0,00007
PISO 26 COMB15 MAX 0,073 0,00277 0,0027 0,0001
PISO 26 COMB15 MIN -0,0717 0,00073 -0,0027 0,00007
PISO 26 COMB17 MAX 0,0547 0,00208 0,0020 0,00007
PISO 26 COMB17 MIN -0,0538 0,00055 -0,0020 0,00005
PISO 25 COMB13 MAX 0,0694 0,00268 0,0026 0,0001
PISO 25 COMB13 MIN -0,0682 0,00069 -0,0026 0,00006
PISO 25 COMB15 MAX 0,0694 0,00268 0,0026 0,0001
PISO 25 COMB15 MIN -0,0682 0,00069 -0,0026 0,00006
PISO 25 COMB17 MAX 0,0521 0,00201 0,0020 0,00008
PISO 25 COMB17 MIN -0,0511 0,00052 -0,0019 0,00005
PISO 24 COMB13 MAX 0,066 0,00259 0,0026 0,00011
PISO 24 COMB13 MIN -0,0647 0,00065 -0,0026 0,00007
PISO 24 COMB15 MAX 0,066 0,00259 0,0026 0,00011
PISO 24 COMB15 MIN -0,0647 0,00065 -0,0026 0,00007
PISO 24 COMB17 MAX 0,0495 0,00194 0,0019 0,00008
PISO 24 COMB17 MIN -0,0485 0,00049 -0,0019 0,00005
PISO 23 COMB13 MAX 0,0626 0,00249 0,0025 0,00011
PISO 23 COMB13 MIN -0,0614 0,00061 -0,0024 0,00006
PISO 23 COMB15 MAX 0,0626 0,00249 0,0025 0,00011
PISO 23 COMB15 MIN -0,0614 0,00061 -0,0024 0,00006
PISO 23 COMB17 MAX 0,0469 0,00187 0,0019 0,00008
94
UX RZ ΔUX ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 23 COMB17 MIN -0,046 0,00046 -0,0019 0,00005
PISO 22 COMB13 MAX 0,0593 0,00239 0,0024 0,00011
PISO 22 COMB13 MIN -0,0581 0,00057 -0,0024 0,00007
PISO 22 COMB15 MAX 0,0593 0,00239 0,0024 0,00011
PISO 22 COMB15 MIN -0,0581 0,00057 -0,0024 0,00007
PISO 22 COMB17 MAX 0,0444 0,00179 0,0018 0,00008
PISO 22 COMB17 MIN -0,0436 0,00042 -0,0018 0,00005
PISO 21 COMB13 MAX 0,0561 0,00228 0,0024 0,00012
PISO 21 COMB13 MIN -0,055 0,00052 -0,0023 0,00006
PISO 21 COMB15 MAX 0,0561 0,00228 0,0024 0,00012
PISO 21 COMB15 MIN -0,055 0,00052 -0,0023 0,00006
PISO 21 COMB17 MAX 0,042 0,00171 0,0018 0,00009
PISO 21 COMB17 MIN -0,0412 0,00039 -0,0017 0,00004
PISO 20 COMB13 MAX 0,0529 0,00217 0,0022 0,00011
PISO 20 COMB13 MIN -0,0519 0,00048 -0,0022 0,00006
PISO 20 COMB15 MAX 0,0529 0,00217 0,0022 0,00011
PISO 20 COMB15 MIN -0,0519 0,00048 -0,0022 0,00006
PISO 20 COMB17 MAX 0,0397 0,00163 0,0017 0,00008
PISO 20 COMB17 MIN -0,0389 0,00036 -0,0016 0,00005
PISO 19 COMB13 MAX 0,0499 0,00207 0,0023 0,00011
PISO 19 COMB13 MIN -0,0489 0,00045 -0,0022 0,00006
PISO 19 COMB15 MAX 0,0499 0,00207 0,0023 0,00011
PISO 19 COMB15 MIN -0,0489 0,00045 -0,0022 0,00006
PISO 19 COMB17 MAX 0,0374 0,00156 0,0016 0,00009
PISO 19 COMB17 MIN -0,0367 0,00033 -0,0017 0,00004
PISO 18 COMB13 MAX 0,0469 0,00197 0,0021 0,00011
PISO 18 COMB13 MIN -0,046 0,00041 -0,0021 0,00005
PISO 18 COMB15 MAX 0,0469 0,00197 0,0021 0,00011
PISO 18 COMB15 MIN -0,046 0,00041 -0,0021 0,00005
PISO 18 COMB17 MAX 0,0352 0,00148 0,0017 0,00008
PISO 18 COMB17 MIN -0,0345 0,00031 -0,0016 0,00004
PISO 17 COMB13 MAX 0,044 0,00187 0,0022 0,00011
PISO 17 COMB13 MIN -0,0431 0,00037 -0,0021 0,00006
PISO 17 COMB15 MAX 0,044 0,00187 0,0022 0,00011
PISO 17 COMB15 MIN -0,0431 0,00037 -0,0021 0,00006
PISO 17 COMB17 MAX 0,033 0,0014 0,0016 0,00009
PISO 17 COMB17 MIN -0,0323 0,00028 -0,0016 0,00004
PISO 16 COMB13 MAX 0,0411 0,00177 0,0021 0,00012
PISO 16 COMB13 MIN -0,0403 0,00033 -0,0021 0,00005
PISO 16 COMB15 MAX 0,0411 0,00177 0,0021 0,00012
PISO 16 COMB15 MIN -0,0403 0,00033 -0,0021 0,00005
PISO 16 COMB17 MAX 0,0309 0,00132 0,0016 0,00008
PISO 16 COMB17 MIN -0,0302 0,00025 -0,0015 0,00005
PISO 15 COMB13 MAX 0,0383 0,00166 0,0021 0,00011
PISO 15 COMB13 MIN -0,0375 0,0003 -0,0021 0,00006
PISO 15 COMB15 MAX 0,0383 0,00166 0,0021 0,00011
PISO 15 COMB15 MIN -0,0375 0,0003 -0,0021 0,00006
PISO 15 COMB17 MAX 0,0287 0,00124 0,0016 0,00009
PISO 15 COMB17 MIN -0,0281 0,00022 -0,0016 0,00004
PISO 14 COMB13 MAX 0,0355 0,00155 0,0021 0,00012
PISO 14 COMB13 MIN -0,0347 0,00026 -0,0020 0,00005
PISO 14 COMB15 MAX 0,0355 0,00155 0,0021 0,00012
PISO 14 COMB15 MIN -0,0347 0,00026 -0,0020 0,00005
PISO 14 COMB17 MAX 0,0266 0,00116 0,0015 0,00008
95
Nivel Combinación
UX RZ ΔUX ΔRZ
(m) (rad) (m) (rad)
PISO 14 COMB17 MIN -0,026 0,0002 -0,0015 0,00004
PISO 13 COMB13 MAX 0,0326 0,00144 0,0021 0,00012
PISO 13 COMB13 MIN -0,0319 0,00023 -0,0021 0,00005
PISO 13 COMB15 MAX 0,0326 0,00144 0,0021 0,00012
PISO 13 COMB15 MIN -0,0319 0,00023 -0,0021 0,00005
PISO 13 COMB17 MAX 0,0245 0,00108 0,0016 0,00009
PISO 13 COMB17 MIN -0,024 0,00017 -0,0016 0,00004
PISO 12 COMB13 MAX 0,0298 0,00133 0,0021 0,00011
PISO 12 COMB13 MIN -0,0292 0,00019 -0,0020 0,00006
PISO 12 COMB15 MAX 0,0298 0,00133 0,0021 0,00011
PISO 12 COMB15 MIN -0,0292 0,00019 -0,0020 0,00006
PISO 12 COMB17 MAX 0,0224 0,001 0,0016 0,00009
PISO 12 COMB17 MIN -0,0219 0,00015 -0,0015 0,00003
PISO 11 COMB13 MAX 0,027 0,00121 0,0021 0,00012
PISO 11 COMB13 MIN -0,0264 0,00016 -0,0020 0,00005
PISO 11 COMB15 MAX 0,027 0,00121 0,0021 0,00012
PISO 11 COMB15 MIN -0,0264 0,00016 -0,0020 0,00005
PISO 11 COMB17 MAX 0,0202 0,00091 0,0015 0,00009
PISO 11 COMB17 MIN -0,0198 0,00012 -0,0015 0,00004
PISO 10 COMB13 MAX 0,0241 0,0011 0,0020 0,00012
PISO 10 COMB13 MIN -0,0236 0,00014 -0,0020 0,00005
PISO 10 COMB15 MAX 0,0241 0,0011 0,0020 0,00012
PISO 10 COMB15 MIN -0,0236 0,00014 -0,0020 0,00005
PISO 10 COMB17 MAX 0,0181 0,00082 0,0016 0,00008
PISO 10 COMB17 MIN -0,0177 0,0001 -0,0015 0,00004
PISO 9 COMB13 MAX 0,0213 0,00098 0,0020 0,00011
PISO 9 COMB13 MIN -0,0209 0,00011 -0,0020 0,00005
PISO 9 COMB15 MAX 0,0213 0,00098 0,0020 0,00011
PISO 9 COMB15 MIN -0,0209 0,00011 -0,0020 0,00005
PISO 9 COMB17 MAX 0,016 0,00074 0,0015 0,00009
PISO 9 COMB17 MIN -0,0156 0,00009 -0,0015 0,00004
PISO 8 COMB13 MAX 0,0185 0,00087 0,0020 0,00012
PISO 8 COMB13 MIN -0,0181 0,00009 -0,0019 0,00005
PISO 8 COMB15 MAX 0,0185 0,00087 0,0020 0,00012
PISO 8 COMB15 MIN -0,0181 0,00009 -0,0019 0,00005
PISO 8 COMB17 MAX 0,0139 0,00065 0,0014 0,00009
PISO 8 COMB17 MIN -0,0136 0,00007 -0,0014 0,00003
PISO 7 COMB13 MAX 0,0157 0,00075 0,0018 0,00011
PISO 7 COMB13 MIN -0,0154 0,00007 -0,0018 0,00004
PISO 7 COMB15 MAX 0,0157 0,00075 0,0018 0,00011
PISO 7 COMB15 MIN -0,0154 0,00007 -0,0018 0,00004
PISO 7 COMB17 MAX 0,0118 0,00056 0,0014 0,00008
PISO 7 COMB17 MIN -0,0115 0,00005 -0,0014 0,00004
PISO 6 COMB13 MAX 0,0129 0,00063 0,0018 0,00011
PISO 6 COMB13 MIN -0,0126 0,00005 -0,0017 0,00005
PISO 6 COMB15 MAX 0,0129 0,00063 0,0018 0,00011
PISO 6 COMB15 MIN -0,0126 0,00005 -0,0017 0,00005
PISO 6 COMB17 MAX 0,0097 0,00047 0,0013 0,00009
PISO 6 COMB17 MIN -0,0095 0,00004 -0,0012 0,00003
PISO 5 COMB13 MAX 0,0101 0,00051 0,0015 0,00011
PISO 5 COMB13 MIN -0,0099 0,00004 -0,0015 0,00004
PISO 5 COMB15 MAX 0,0101 0,00051 0,0015 0,00011
PISO 5 COMB15 MIN -0,0099 0,00004 -0,0015 0,00004
PISO 5 COMB17 MAX 0,0076 0,00038 0,0012 0,00007
96
Nivel Combinación
UX RZ ΔUX ΔRZ
(m) (rad) (m) (rad)
PISO 5 COMB17 MIN -0,0074 0,00003 -0,0012 0,00003
PISO 4 COMB13 MAX 0,0075 0,00038 0,0014 0,00009
PISO 4 COMB13 MIN -0,0073 0,00003 -0,0014 0,00003
PISO 4 COMB15 MAX 0,0075 0,00038 0,0014 0,00009
PISO 4 COMB15 MIN -0,0073 0,00003 -0,0014 0,00003
PISO 4 COMB17 MAX 0,0056 0,00029 0,0010 0,00008
PISO 4 COMB17 MIN -0,0055 0,00002 -0,0010 0,00003
PISO 3 COMB13 MAX 0,005 0,00026 0,0010 0,00009
PISO 3 COMB13 MIN -0,0049 0,00002 -0,0010 0,00004
PISO 3 COMB15 MAX 0,005 0,00026 0,0010 0,00009
PISO 3 COMB15 MIN -0,0049 0,00002 -0,0010 0,00004
PISO 3 COMB17 MAX 0,0037 0,0002 0,0008 0,00006
PISO 3 COMB17 MIN -0,0037 0,00001 -0,0007 0,00002
PISO 2 COMB13 MAX 0,0028 0,00015 0,0008 0,00006
PISO 2 COMB13 MIN -0,0027 0,00001 -0,0007 0,00002
PISO 2 COMB15 MAX 0,0028 0,00015 0,0008 0,00006
PISO 2 COMB15 MIN -0,0027 0,00001 -0,0007 0,00002
PISO 2 COMB17 MAX 0,0021 0,00011 0,0006 0,00005
PISO 2 COMB17 MIN -0,0021 0,00001 -0,0006 0,00002
PISO 1 COMB13 MAX 0,001 0,00005 0,0003 0,00003
PISO 1 COMB13 MIN -0,001 0 -0,0003 0,00001
PISO 1 COMB15 MAX 0,001 0,00005 0,0003 0,00003
PISO 1 COMB15 MIN -0,001 0 -0,0003 0,00001
PISO 1 COMB17 MAX 0,0008 0,00004 0,0002 0,00002
PISO 1 COMB17 MIN -0,0007 0 -0,0002 0,00001
Donde:
97
TABLA 4.15: Deformaciones para Sismo en dirección X, Edificio Mixto.
Nivel Combinación
UY RZ ΔUY ΔRZ
(m) (rad) (m) (rad)
PISO 30 COMB14 MAX 0,1013 0,00304 0,00260 0,00005
PISO 30 COMB14 MIN -0,1013 0,00304 -0,00260 0,00005
PISO 30 COMB16 MAX 0,0977 0,00304 0,00240 0,00005
PISO 30 COMB16 MIN -0,1049 0,00304 -0,00270 0,00005
PISO 30 COMB18 MAX 0,0715 0,00228 0,00170 0,00003
PISO 30 COMB18 MIN -0,0804 0,00228 -0,00210 0,00003
PISO 29 COMB14 MAX 0,0987 0,00299 0,00280 0,00006
PISO 29 COMB14 MIN -0,0987 0,00299 -0,00280 0,00006
PISO 29 COMB16 MAX 0,0953 0,00299 0,00270 0,00006
PISO 29 COMB16 MIN -0,1022 0,00299 -0,00310 0,00006
PISO 29 COMB18 MAX 0,0698 0,00225 0,00190 0,00005
PISO 29 COMB18 MIN -0,0783 0,00225 -0,00240 0,00005
PISO 28 COMB14 MAX 0,0959 0,00293 0,00310 0,00008
PISO 28 COMB14 MIN -0,0959 0,00293 -0,00310 0,00008
PISO 28 COMB16 MAX 0,0926 0,00293 0,00290 0,00008
PISO 28 COMB16 MIN -0,0991 0,00293 -0,00330 0,00008
PISO 28 COMB18 MAX 0,0679 0,0022 0,00200 0,00007
PISO 28 COMB18 MIN -0,0759 0,0022 -0,00260 0,00007
PISO 27 COMB14 MAX 0,0928 0,00285 0,00330 0,00010
PISO 27 COMB14 MIN -0,0928 0,00285 -0,00330 0,00010
PISO 27 COMB16 MAX 0,0897 0,00285 0,00300 0,00010
PISO 27 COMB16 MIN -0,0958 0,00285 -0,00340 0,00010
PISO 27 COMB18 MAX 0,0659 0,00213 0,00230 0,00007
PISO 27 COMB18 MIN -0,0733 0,00213 -0,00270 0,00007
PISO 26 COMB14 MAX 0,0895 0,00275 0,00330 0,00011
PISO 26 COMB14 MIN -0,0895 0,00275 -0,00330 0,00011
PISO 26 COMB16 MAX 0,0867 0,00275 0,00320 0,00011
PISO 26 COMB16 MIN -0,0924 0,00275 -0,00360 0,00011
PISO 26 COMB18 MAX 0,0636 0,00206 0,00220 0,00008
PISO 26 COMB18 MIN -0,0706 0,00206 -0,00270 0,00008
PISO 25 COMB14 MAX 0,0862 0,00264 0,00350 0,00011
PISO 25 COMB14 MIN -0,0862 0,00264 -0,00350 0,00011
PISO 25 COMB16 MAX 0,0835 0,00264 0,00320 0,00011
PISO 25 COMB16 MIN -0,0888 0,00264 -0,00360 0,00011
PISO 25 COMB18 MAX 0,0614 0,00198 0,00240 0,00008
PISO 25 COMB18 MIN -0,0679 0,00198 -0,00280 0,00008
PISO 24 COMB14 MAX 0,0827 0,00253 0,00340 0,00012
PISO 24 COMB14 MIN -0,0827 0,00253 -0,00340 0,00012
PISO 24 COMB16 MAX 0,0803 0,00253 0,00330 0,00012
PISO 24 COMB16 MIN -0,0852 0,00253 -0,00360 0,00012
PISO 24 COMB18 MAX 0,059 0,0019 0,00230 0,00009
PISO 24 COMB18 MIN -0,0651 0,0019 -0,00280 0,00009
PISO 23 COMB14 MAX 0,0793 0,00241 0,00340 0,00012
PISO 23 COMB14 MIN -0,0793 0,00241 -0,00340 0,00012
PISO 23 COMB16 MAX 0,077 0,00241 0,00320 0,00012
PISO 23 COMB16 MIN -0,0816 0,00241 -0,00360 0,00012
PISO 23 COMB18 MAX 0,0567 0,00181 0,00240 0,00009
PISO 23 COMB18 MIN -0,0623 0,00181 -0,00280 0,00009
PISO 22 COMB14 MAX 0,0759 0,00229 0,00340 0,00011
PISO 22 COMB14 MIN -0,0759 0,00229 -0,00340 0,00011
98
UY RZ ΔUY ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 22 COMB16 MAX 0,0738 0,00229 0,00330 0,00011
PISO 22 COMB16 MIN -0,078 0,00229 -0,00360 0,00011
PISO 22 COMB18 MAX 0,0543 0,00172 0,00230 0,00009
PISO 22 COMB18 MIN -0,0595 0,00172 -0,00280 0,00009
PISO 21 COMB14 MAX 0,0725 0,00218 0,00350 0,00012
PISO 21 COMB14 MIN -0,0725 0,00218 -0,00350 0,00012
PISO 21 COMB16 MAX 0,0705 0,00218 0,00320 0,00012
PISO 21 COMB16 MIN -0,0744 0,00218 -0,00360 0,00012
PISO 21 COMB18 MAX 0,052 0,00163 0,00240 0,00009
PISO 21 COMB18 MIN -0,0567 0,00163 -0,00270 0,00009
PISO 20 COMB14 MAX 0,069 0,00206 0,00320 0,00011
PISO 20 COMB14 MIN -0,069 0,00206 -0,00320 0,00011
PISO 20 COMB16 MAX 0,0673 0,00206 0,00310 0,00011
PISO 20 COMB16 MIN -0,0708 0,00206 -0,00340 0,00011
PISO 20 COMB18 MAX 0,0496 0,00154 0,00220 0,00008
PISO 20 COMB18 MIN -0,054 0,00154 -0,00270 0,00008
PISO 19 COMB14 MAX 0,0658 0,00195 0,00320 0,00011
PISO 19 COMB14 MIN -0,0658 0,00195 -0,00320 0,00011
PISO 19 COMB16 MAX 0,0642 0,00195 0,00310 0,00011
PISO 19 COMB16 MIN -0,0674 0,00195 -0,00340 0,00011
PISO 19 COMB18 MAX 0,0474 0,00146 0,00220 0,00008
PISO 19 COMB18 MIN -0,0513 0,00146 -0,00260 0,00008
PISO 18 COMB14 MAX 0,0626 0,00184 0,00330 0,00011
PISO 18 COMB14 MIN -0,0626 0,00184 -0,00330 0,00011
PISO 18 COMB16 MAX 0,0611 0,00184 0,00310 0,00011
PISO 18 COMB16 MIN -0,064 0,00184 -0,00340 0,00011
PISO 18 COMB18 MAX 0,0452 0,00138 0,00230 0,00008
PISO 18 COMB18 MIN -0,0487 0,00138 -0,00260 0,00008
PISO 17 COMB14 MAX 0,0593 0,00173 0,00330 0,00011
PISO 17 COMB14 MIN -0,0593 0,00173 -0,00330 0,00011
PISO 17 COMB16 MAX 0,058 0,00173 0,00310 0,00011
PISO 17 COMB16 MIN -0,0606 0,00173 -0,00350 0,00011
PISO 17 COMB18 MAX 0,0429 0,0013 0,00230 0,00009
PISO 17 COMB18 MIN -0,0461 0,0013 -0,00270 0,00009
PISO 16 COMB14 MAX 0,056 0,00162 0,00330 0,00012
PISO 16 COMB14 MIN -0,056 0,00162 -0,00330 0,00012
PISO 16 COMB16 MAX 0,0549 0,00162 0,00320 0,00012
PISO 16 COMB16 MIN -0,0571 0,00162 -0,00340 0,00012
PISO 16 COMB18 MAX 0,0406 0,00121 0,00230 0,00008
PISO 16 COMB18 MIN -0,0434 0,00121 -0,00270 0,00008
PISO 15 COMB14 MAX 0,0527 0,0015 0,00340 0,00011
PISO 15 COMB14 MIN -0,0527 0,0015 -0,00340 0,00011
PISO 15 COMB16 MAX 0,0517 0,0015 0,00320 0,00011
PISO 15 COMB16 MIN -0,0537 0,0015 -0,00350 0,00011
PISO 15 COMB18 MAX 0,0383 0,00113 0,00240 0,00009
PISO 15 COMB18 MIN -0,0407 0,00113 -0,00260 0,00009
PISO 14 COMB14 MAX 0,0493 0,00139 0,00330 0,00011
PISO 14 COMB14 MIN -0,0493 0,00139 -0,00330 0,00011
PISO 14 COMB16 MAX 0,0485 0,00139 0,00330 0,00011
PISO 14 COMB16 MIN -0,0502 0,00139 -0,00350 0,00011
PISO 14 COMB18 MAX 0,0359 0,00104 0,00230 0,00008
PISO 14 COMB18 MIN -0,0381 0,00104 -0,00270 0,00008
PISO 13 COMB14 MAX 0,046 0,00128 0,00340 0,00012
PISO 13 COMB14 MIN -0,046 0,00128 -0,00340 0,00012
99
UY RZ ΔUY ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 13 COMB16 MAX 0,0452 0,00128 0,00330 0,00012
PISO 13 COMB16 MIN -0,0467 0,00128 -0,00350 0,00012
PISO 13 COMB18 MAX 0,0336 0,00096 0,00250 0,00009
PISO 13 COMB18 MIN -0,0354 0,00096 -0,00270 0,00009
PISO 12 COMB14 MAX 0,0426 0,00116 0,00350 0,00011
PISO 12 COMB14 MIN -0,0426 0,00116 -0,00350 0,00011
PISO 12 COMB16 MAX 0,0419 0,00116 0,00330 0,00011
PISO 12 COMB16 MIN -0,0432 0,00116 -0,00350 0,00011
PISO 12 COMB18 MAX 0,0311 0,00087 0,00240 0,00008
PISO 12 COMB18 MIN -0,0327 0,00087 -0,00270 0,00008
PISO 11 COMB14 MAX 0,0391 0,00105 0,00350 0,00011
PISO 11 COMB14 MIN -0,0391 0,00105 -0,00350 0,00011
PISO 11 COMB16 MAX 0,0386 0,00105 0,00350 0,00011
PISO 11 COMB16 MIN -0,0397 0,00105 -0,00370 0,00011
PISO 11 COMB18 MAX 0,0287 0,00079 0,00260 0,00009
PISO 11 COMB18 MIN -0,03 0,00079 -0,00280 0,00009
PISO 10 COMB14 MAX 0,0356 0,00094 0,00350 0,00011
PISO 10 COMB14 MIN -0,0356 0,00094 -0,00350 0,00011
PISO 10 COMB16 MAX 0,0351 0,00094 0,00330 0,00011
PISO 10 COMB16 MIN -0,036 0,00094 -0,00350 0,00011
PISO 10 COMB18 MAX 0,0261 0,0007 0,00240 0,00007
PISO 10 COMB18 MIN -0,0272 0,0007 -0,00270 0,00007
PISO 9 COMB14 MAX 0,0321 0,00083 0,00350 0,00010
PISO 9 COMB14 MIN -0,0321 0,00083 -0,00350 0,00010
PISO 9 COMB16 MAX 0,0318 0,00083 0,00350 0,00010
PISO 9 COMB16 MIN -0,0325 0,00083 -0,00370 0,00010
PISO 9 COMB18 MAX 0,0237 0,00063 0,00260 0,00008
PISO 9 COMB18 MIN -0,0245 0,00063 -0,00270 0,00008
PISO 8 COMB14 MAX 0,0286 0,00073 0,00380 0,00011
PISO 8 COMB14 MIN -0,0286 0,00073 -0,00380 0,00011
PISO 8 COMB16 MAX 0,0283 0,00073 0,00370 0,00011
PISO 8 COMB16 MIN -0,0288 0,00073 -0,00370 0,00011
PISO 8 COMB18 MAX 0,0211 0,00055 0,00270 0,00008
PISO 8 COMB18 MIN -0,0218 0,00055 -0,00290 0,00008
PISO 7 COMB14 MAX 0,0248 0,00062 0,00380 0,00010
PISO 7 COMB14 MIN -0,0248 0,00062 -0,00380 0,00010
PISO 7 COMB16 MAX 0,0246 0,00062 0,00380 0,00010
PISO 7 COMB16 MIN -0,0251 0,00062 -0,00400 0,00010
PISO 7 COMB18 MAX 0,0184 0,00047 0,00280 0,00008
PISO 7 COMB18 MIN -0,0189 0,00047 -0,00300 0,00008
PISO 6 COMB14 MAX 0,021 0,00052 0,00400 0,00011
PISO 6 COMB14 MIN -0,021 0,00052 -0,00400 0,00011
PISO 6 COMB16 MAX 0,0208 0,00052 0,00390 0,00011
PISO 6 COMB16 MIN -0,0211 0,00052 -0,00400 0,00011
PISO 6 COMB18 MAX 0,0156 0,00039 0,00300 0,00008
PISO 6 COMB18 MIN -0,0159 0,00039 -0,00300 0,00008
PISO 5 COMB14 MAX 0,017 0,00041 0,00400 0,00010
PISO 5 COMB14 MIN -0,017 0,00041 -0,00400 0,00010
PISO 5 COMB16 MAX 0,0169 0,00041 0,00400 0,00010
PISO 5 COMB16 MIN -0,0171 0,00041 -0,00410 0,00010
PISO 5 COMB18 MAX 0,0126 0,00031 0,00290 0,00008
PISO 5 COMB18 MIN -0,0129 0,00031 -0,00310 0,00008
PISO 4 COMB14 MAX 0,013 0,00031 0,00400 0,00010
PISO 4 COMB14 MIN -0,013 0,00031 -0,00400 0,00010
100
UY RZ ΔUY ΔRZ
Nivel Combinación
(m) (rad) (m) (rad)
PISO 4 COMB16 MAX 0,0129 0,00031 0,00400 0,00010
PISO 4 COMB16 MIN -0,013 0,00031 -0,00400 0,00010
PISO 4 COMB18 MAX 0,0097 0,00023 0,00300 0,00007
PISO 4 COMB18 MIN -0,0098 0,00023 -0,00310 0,00007
PISO 3 COMB14 MAX 0,009 0,00021 0,00390 0,00009
PISO 3 COMB14 MIN -0,009 0,00021 -0,00390 0,00009
PISO 3 COMB16 MAX 0,0089 0,00021 0,00380 0,00009
PISO 3 COMB16 MIN -0,009 0,00021 -0,00390 0,00009
PISO 3 COMB18 MAX 0,0067 0,00016 0,00290 0,00007
PISO 3 COMB18 MIN -0,0067 0,00016 -0,00280 0,00007
PISO 2 COMB14 MAX 0,0051 0,00012 0,00330 0,00008
PISO 2 COMB14 MIN -0,0051 0,00012 -0,00330 0,00008
PISO 2 COMB16 MAX 0,0051 0,00012 0,00330 0,00008
PISO 2 COMB16 MIN -0,0051 0,00012 -0,00330 0,00008
PISO 2 COMB18 MAX 0,0038 0,00009 0,00240 0,00006
PISO 2 COMB18 MIN -0,0039 0,00009 -0,00250 0,00006
PISO 1 COMB14 MAX 0,0018 0,00004 0,00180 0,00004
PISO 1 COMB14 MIN -0,0018 0,00004 -0,00180 0,00004
PISO 1 COMB16 MAX 0,0018 0,00004 0,00180 0,00004
PISO 1 COMB16 MIN -0,0018 0,00004 -0,00180 0,00004
PISO 1 COMB18 MAX 0,0014 0,00003 0,00140 0,00003
PISO 1 COMB18 MIN -0,0014 0,00003 -0,00140 0,00003
Donde:
101
4.3 EXCENTRICIDAD ARRIOSTRAMIENTOS
e T
(cm) (seg)
0 2,8707
10 2,8828
20 2,8987
25 2,9108
30 2,9167
40 2,9365
50 2,9579
60 2,9818
70 3,0071
75 3,0204
80 3,034
90 3,0626
100 3,0926
102
GRAFICO 4.1: Influencia de excentricidad en el período.
3,15
3,1
3,05
T (seg)
2,95
2,9
2,85
0 20 40 60 80 100 120
Excentricidad (cm)
103
4.4 EVALUACION ECONOMICA
Precio Precio
Item Descripción Unidad Cantidad Unitario parcial Total
U. F. U. F.
3
1 Hormigón de Muros H30-95% m 1342 2,2 2952,40
3
2 Hormigón de vigas H30-95% m 23 2,2 50,60
3
3 Hormigón losas H30-95% m 2624 2,2 5772,80
4 Acero refuerzo (A44-28H) kg 386167 0,016 6178,67
5 Acero A42-27ES kg 1758882 0,024 42213,17
TOTAL 57167,64
Precio
Precio
parcial
Item Descripción Unidad Cantidad Unitario
Total
U. F.
U. F.
3
1 Hormigón losas H30-95% m 2624 2,2 5772,80
2 Acero refuerzo (A44-28H) kg 246656 0,016 3946,50
3 Acero A42-27ES kg 2405966 0,024 57743,18
TOTAL 67462,48
104
4.5 COMPARACIÓN DE RESULTADOS
Edificio Edificio
Item
Mixto Acero
Periodo modo 1 (s) 2,7368 2,8707
Período Torsional Período Traslacional
1
Ingeniero Civil U. de Chile; Socio de Bascuñán, Maccioni e Ing, Asociados; Ha desarrollado más de 1200 proyectos en
Ingeniería estructural; Ha dictado diversos cursos en la Universidad y en el diseño de LRFD y de Diseño Sísmico para Estructuras
de Acero; Autor de diversas publicaciones.
105
CAPITULO V
Conclusiones
El trabajo realizado en la presente memoria, consistió básicamente en
desarrollar el Análisis Estructural de dos edificios altos en estructura de acero, el
primero, marcos de momento de acero en la periferia y núcleo de escaleras y
ascensor de muros de hormigón armado. El segundo, con marcos de momento de
acero en la periferia y núcleo de escaleras y ascensor de marcos arriostrados
concéntricos de acero.
5.1 Factibilidad
Los períodos en ambas estructuras son menores que los considerados como
límite, que en este caso fue T = 2.9 seg, lo que representa una buena rigidez
lateral, para ambos casos.
107
Las deformaciones relativas entre pisos cumplen con las restricciones de la
NCh433of.96, que establece como máximo un 0.002 por la altura del piso, para el
caso estudiado: 2.9 m, lo que corresponde a una deformación máxima relativa de
0.0058 m.
Si bien los costos del Edificio Acero son relativamente más altos que en el
Edificio Mixto, hay que considerar que sólo fue analizado los costos por material, pero si
se hiciera un estudio más acabado, considerando variables como superficie útil, plazos
constructivos, montaje, fundaciones, etc., los costos podrían ser similares o inclusive
más bajos en el Edificio Acero. Además la tendencia mundial de hoy día, indica
disminución en el precio de este material, lo que implicaría una ventaja futura en este
tipo de estructuras.
108
BIBLIOGRAFIA
1. Brockenbrough, R., Merritt, F., “Manual de Diseño de Estructuras de Acero, Tomo II”,
McGraw – Hill Interamercana S. A., Colombia, 1998.
3. “Manual de Diseño para Estructuras de Acero”, Instituto Chileno del Acero, Santiago,
2001.
4. “Load and Resistance Factor Design Specification for Structural Steel Buildings”,
American Institute of Steel Construction, Chicago, 1994.
8. NCh 432 0f71: "Calculo de acción del viento sobre las construcciones", Instituto
Nacional de Normalización, Chile, 1971.
11. NCh 430 EOf61: "Hormigón Armado – II Parte", Instituto Nacional de Normalización,
Chile, 1961.
109