Documentos de Académico
Documentos de Profesional
Documentos de Cultura
H
0.625H
0.25H
0.125H
ROSCA EXTERNA
ROSCA INTERNA
MARYLAND METRICS
THREAD DATA CHARTS
METRIC THREAD -- EXTENDED THREAD SIZE
RANGE (ISO)
Thread Height Male Thread = h3 Thread Height Female Thread = H1
in mm in mm in mm in mm in
1/8" 27 0.4050 10.287 0.0370 0.941 0.02963 0.753 0.0036 0.091 0.3736 9.489 0.1620
1/4" 18 0.5400 13.716 0.0556 1.411 0.04444 1.129 0.0049 0.124 0.49163 12.487 0.2280
3/8" 18 0.6750 17.145 0.0556 1.411 0.04444 1.129 0.0049 0.124 0.62701 15.926 0.2400
1/2" 14 0.8400 21.336 0.0714 1.814 0.05714 1.451 0.0056 0.142 0.77843 19.772 0.3200
3/4" 14 1.0500 26.670 0.0714 1.814 0.05714 1.451 0.0056 0.142 0.98887 25.117 0.3390
1" 11.5 1.3150 33.401 0.0870 2.209 0.06957 1.767 0.0063 0.160 1.23863 31.461 0.4000
1-1/4" 11.5 1.6600 42.164 0.0870 2.209 0.06957 1.767 0.0063 0.160 1.58338 40.218 0.4200
1-1/2" 11.5 1.9000 48.260 0.0870 2.209 0.06957 1.767 0.0063 0.160 1.82234 46.287 0.4020
2" 11.5 2.3750 60.325 0.0870 2.209 0.06957 1.767 0.0063 0.160 2.29627 58.325 0.4360
2-1/2" 8 2.8750 73.025 0.1250 3.175 0.1 2.540 0.0078 0.198 2.76215 70.159 0.6820
3" 8 3.5000 88.900 0.1250 3.175 0.1 2.540 0.0078 0.198 3.3885 86.068 0.7660
3-1/2" 8 4.0000 101.600 0.1250 3.175 0.1 2.540 0.0078 0.198 3.88881 98.776 0.8210
4" 8 4.5000 114.300 0.1250 3.175 0.1 2.540 0.0078 0.198 4.38712 111.433 0.8440
5" 8 5.5630 141.300 0.1250 3.175 0.1 2.540 0.0078 0.198 5.44929 138.412 0.9370
6" 8 6.6250 168.275 0.1250 3.175 0.1 2.540 0.0078 0.198 6.50597 165.252 0.9580
8" 8 8.6250 219.075 0.1250 3.175 0.1 2.540 0.0078 0.198 8.50003 215.901 1.6300
10" 8 10.7500 273.050 0.1250 3.175 0.1 2.540 0.0078 0.198 10.62094 296.772 1.2100
12" 8 12.7500 323.850 0.1250 3.175 0.1 2.540 0.0078 0.198 12.61781 320.493 1.3600
14" 8 14.0000 355.600 0.1250 3.175 0.1 2.540 0.0078 0.198 13.87262 352.365 1.5620
16" 8 16.0000 406.400 0.1250 3.175 0.1 2.540 0.0078 0.198 15.87575 403.244 1.8120
18" 8 18.0000 457.200 0.1250 3.175 0.1 2.540 0.0078 0.198 17.875 454.025 2.0000
20" 8 20.0000 508.000 0.1250 3.175 0.1 2.540 0.0078 0.198 19.87031 504.706 2.1250
24" 8 24.0000 609.600 0.1250 3.175 0.1 2.540 0.0078 0.198 23.68094 606.066 2.3750
Notes:
* Ream the hole before tapping with a reamer having a taper of 3/4 inch per foot. Pipe Size
is the accepted industry designation and does not refer to either the inside or the outside
diameter (ID or OD) of a pipe or a fitting. Dimensions in Inches except where stated
E= Pitch diameter at hand-tight plane. This is also the pitch diameter at the gauge plane.
**'= Truncation from point of thread triangle to flat (not shown in diagram). Minimum = 0.033P for all
pitches. See table for maximum.
Tolerances:
When using L1 gauges to check threads, the thread is within permissible tolerance if the ring
gauge face, or plug gauge notch, is +/- 1 turn from being flush with the end of the thread.
Example designation:
3/8 - 18 NPT where
3/8 = nominal pipe size
18 = number of threads per inch
NPT = symbol for the thread series and
form (i.e., National (American)Standard Pipe, Taper)
Note- Basic dimensions are given to four or five decimal places to eliminate errors when
calculating gauge dimensions, they do not imply a greater degree of precision than is normally
obtainable.
L1= Length of normal hand-tight engagement. This is also the L1 gauge length.
(Longer thread engagement may be used in special applications, such as flanges
for high pressure use. In such cases the pitch diameter, E, remains as specified
and the diameter at the end of the pipe is proportionally smaller.)
4.36 0.2639 7.12 0.1285 3.47 0.36351 0.38000 21/64" 0.3281 8.3344 Q
4.10 0.4018 7.23 0.1928 3.47 0.47739 0.50250 27/64" 0.4219 10.7156 7/16"
4.32 0.4078 7.34 0.1928 3.47 0.61201 0.63750 9/16" 0.5625 14.2875 37/64"
4.48 0.5337 7.47 0.2478 3.47 0.75843 0.79179 11/16" 0.6875 17.4625 45/64"
4.75 0.5457 7.64 0.2478 3.47 0.96768 1.00179 57/64" 0.8906 22.6219 29/32"
4.60 0.6828 7.85 0.3017 3.47 1.21363 1.25630 1-1/8" 1.1250 28.5750 1-9/32"
4.83 0.7068 8.13 0.3017 3.47 1.55713 1.60130 1-15/32" 1.4688 37.3063 1-31/64"
4.83 0.7235 8.32 0.3017 3.47 1.79609 1.84130 1-23/32" 1.7188 43.6563 1-23/32"
5.01 0.7565 8.7 0.3017 3.47 2.26902 2.31630 2-5/32" 2.1563 54.7688 2-3/16"
5.46 1.1375 9.1 0.4337 3.47 2.71953 2.79062 2-25/32" 2.7813 70.6438 2-5/8"
6.13 1.2000 9.6 0.4337 3.47 3.34062 3.41562 3-9/32" 3.2813 83.3438 3-1/4"
6.57 1.2500 10 0.4337 3.47 3.83750 3.91562 3-3/4" 3.7500 95.2500 3-3/4"
6.75 1.3000 10.4 0.4337 3.47 4.33438 4.41562 4-1/4" 4.2500 107.9500 4-1/4"
7.50 1.4063 11.25 0.4337 3.47 5.39073 5.47862 5-1/4" 5.2500 133.3500 5-9/32"
7.66 1.5125 12.1 0.4337 3.47 6.44609 6.54062 6-1/4" 6.2500 158.7500 6-11/32"