Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Extrusor - Prusa3D
5. Extrusor
Escrito Por: Dozuki System (and 3 other contributors)
Di cultad Moderar
Pasos 26
Secciones 1
Banderas 0
Alicates
Un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 1/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
Un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 2/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 3/15
12/8/2017 5. Extrusor - Prusa3D
Tornillos M3x30
Un comentario
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 4/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 5/15
12/8/2017 5. Extrusor - Prusa3D
Tornillos M3x18
Un comentario
5x16sh eje.
M5w rondana.
625 balero.
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 6/15
12/8/2017 5. Extrusor - Prusa3D
Tornillo M3x40
Rondana M3w
Agregar un comentario
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 7/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
Un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 8/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
2 comments
http://manual.prusa3d.com/Guide/5.+Extrusor/56 9/15
12/8/2017 5. Extrusor - Prusa3D
Ventilador 5015
Agregar un comentario
Tornillos M3x20
Tuercas M3
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 10/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
4 comments
http://manual.prusa3d.com/Guide/5.+Extrusor/56 11/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 12/15
12/8/2017 5. Extrusor - Prusa3D
Agregar un comentario
Agregar un comentario
http://manual.prusa3d.com/Guide/5.+Extrusor/56 13/15
12/8/2017 5. Extrusor - Prusa3D
Paso 26 Listo!
Agregar un comentario
LINEA DE META
Dozuki System
Member since: 24/09/09
1 Reputacin
76 Guides authored
Step 19 seem slightly different, a M3x18 was left and a bolt was already in the x-carriage, seems like the M3x18 ts perfectly too
Ben - 29/08/15
http://manual.prusa3d.com/Guide/5.+Extrusor/56 14/15
12/8/2017 5. Extrusor - Prusa3D
assuming long spiral as it seems that way in the overall picture of the i3
Ben - 29/08/15
Step 20: doesn't seem like liment goes very far into fan, like 20 mm, is that normal?
Ben - 29/08/15
just realized I used lament from the 1.75mm roll, but should I be using the thicker looking lament that is clear that came with the parts... ?
What is its purpose? Keep some springiness to the extruder cables...?
Ben - 30/08/15
According to the E3D assembly instructions, you instructions show the heater block upside down. They show the nozzle on the same side as
the screw that tightens the block on the ceramic heater. This make more sense as the heater is closer to the nozzle and further from the
heatsink and the thermistor is near the nozzle not near the heatsink.
James Stolpman - 18/02/16
Agregar Comentario
Publicar comentario
Ver Estadsticas: Ultimas 24 Horas: 16 ltimos 7 Das: 123 ltimos 30 Das: 598 Todo El Tiempo: 14,926
http://manual.prusa3d.com/Guide/5.+Extrusor/56 15/15