Documentos de Académico
Documentos de Profesional
Documentos de Cultura
MULTIVIBRADOR ASTABLE
CON 555
Asociacin de resistores
ndice:
Introduccin...pgina 3
Breve explicacin....pgina 3
Diseo por Ultiboard....pgina 3
Proceso del montaje de la placa......pgina 3
Datos de ultiboardpgina 4
Datos de Multisim...pgina 5
Esquema de Multisim.....pgina 7
Grfica LED..pgina 8
Grfica C1....pgina 9
Placa de componentes.........pgina 10
Placa de Ultiboard serigrafiado.pgina 11
Conclusiones..pgina 12
Datasheet......pgina 13
Asociacin de resistores
Introduccin.
En esta prctica vamos a realizar un circuito multivibrador 555 ruteado a simple cara con el
mtodo sgueme.
Breve explicacin
En esta prctica nos hemos iniciado en el ruteo con el mtodo del sgueme y aadido los
componentes del esquema realizado por Multisim buscndolo a travs de su librera teniendo
en cuenta el capsulado de los componentes que vamos a montar. Una vez realizado el
esquema del circuito por Multisim y rutado la placa por ultiboard procederemos al montaje de
la placa.
Diseo por ultiboard.
En este proyecto el diseo del circuito lo realizaremos en ultiboard con el mtodo del
sgueme.
El diseo de la placa seleccionamos la opcin contorno de la tarjeta, y nos vamos a colocar,
grficos y rectngulo, con un tamao del 40x40 con 8mm de grosor.
Una vez tenemos el contorno de la placa empezaremos a aadir los componentes que
tendremos que buscar en la biblioteca de ultiboard, con los correspondientes encapsulados de
los componentes.
El grosor de los pads ser de 2.5mm y el grosor del taladro de 0.6mm.
Una vez terminado con ultiboard procederemos al montaje de la placa.
Proceso del montaje de la placa
Una vez que tenemos ya el circuito impreso, pasaremos a la insoladora con un tiempo de 120
segundos, la placa fotosensible a usar es a simple cara.
Pasado los 120 segundos pasamos al revelado de la placa.
El revelado se realizara en la cuba. En la primera ranura se encuentra la sosa caustica que es
con la que podremos realizar el revelado de la placa, en esta parte hay que tener un poco de
cuidado, ya que si lo dejamos de manera prolongada esta se come las pistas, tenemos que
meterlo dentro e ir oxigenndolo de manera continuada y podremos ver como se visualiza las
pistas, una vez que hemos hecho el revelado lo pasaremos a la apertura central para echarle
Asociacin de resistores
un poco de agua y a continuacin lo pasamos a la tercera apertura en la que se encuentra el
cido que atacar a la placa dejando solo la parte de las pistas.
Una vez tengamos las pistas lo llevamos al fregadero y le echaremos agua y restregaremos con
la scotch brite y lijaremos los laterales de la placa.
Ya con la placa impresa, pasaremos a hacerle las marcaras con un granete y el taladrado de los
pads con una broca de 0,8mm.
Una vez taladrado ya podremos soldar los componentes y comprobar el funcionamiento de la
placa.
Datos de ultiboard
Estadsticas de la placa.
Parts: 12
Nets: 7
Vias: 0
Pins in net: 22
Pins: 22
Connections: 15
Test pins: 0
Unrouted connections: 2
Jumpers: 0
Router
completion
rate:
86
Asociacin de resistores
Lista de materiales
VALUE
SHAPE
REFDES
KERKO7X6R2_5
U6
SK_M3
U2,U3,U4,U5
1.0kOhm
RES1300-700X250
R1,R2,R3
1uF
CAPPR150-400X500
C1
HDR1X2
MKDS1_2R3_8
J1
LED_red
LED3R2_5Vy
LED1
LM555CN
DIP8300
U1
Datos de Multisim
Lista de materiales
Asociacin de resistores
Reporte NetList
Lista estadsticas
VCC
VCC
5V
5V
J1
HDR1X2
R1
15k
U1
LED1
VCC
4
RST
DIS
THR
R2
TRI
150k
CON
OUT
R3
GND
1
C1
C2
1F
10nF
560
LM555CN
Dibujado:
Francisco Jose
Comprobado:
Fecha:
24/02/2015
Firmado
Led
6.0
4.8
Voltaje(V)
3.7
2.5
1.3
166.7m
-1.0
0.0
200.0m
400.0m
600.0m
Tiempo (s)
Canal A
800.0m
1.0
Condensador C1
6.0
4.8
Voltaje(V)
3.7
2.5
1.3
166.7m
-1.0
0.0
200.0m
400.0m
600.0m
Tiempo (s)
Canal A
800.0m
1.0
Serigrafa Superior
Cobre Inferior
Asociacin de resistores
Conclusiones
Con este proyecto, el uso del sgueme de ultiboard ha facilitado la tarea de saber dnde
llevar el conexionado de los nodos, pero a la vez hemos tenido que usar un poco ms la cabeza
para evitar que se crucen las pistas, sobre todo en el integrado 555.
Specifications
Item
Performance
-40C to +85C
10 to 100V DC
0.1 to 22,000F
Capacitance Tolerance
Leakage Current
Which ever is greater after 3 mins.
I : Leakage Current(A)
C : Rated Capacitance(F)
V : Working Voltage(v)
10
16
25
35
50
63
100
tan Max.
0.2
0.17
0.15
0.12
0.1
0.09
0.08
Frequency (Hz)
50 / 60
120
1K
10 K
0.7
1.3
1.7
Working voltage
(V)
10
16
25
35
50
63
100
-25C / +20C
-40C / +20C
For capacitance value > 1,000 F, Add 0.5 per another 1,000 F for
-25C / +25C. Add 1 per another 1,000 F for -40C / +20C.
After 2,000 hours application of DC rated working voltage at +85C,
The capacitor shall meet the following limits:
Post test requirements at +20C.
High Temperature Loading
Shelf Life
Leakage current
Capacitance change
www.element14.com
www.farnell.com
www.newark.com
Page <1>
17/04/12
V1.0
Dimensions : Millimetres
D (+0.5 Max.)
6.3
10
13
16
18
22
25
F (0.5)
2.5
3.5
7.5
7.5
10
12
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
0.8
d (0.02)
D x L (mm)
W V (SV)
F
10
(13)
16
(20)
25
(32)
35
(44)
0.1
0.22
0.33
0.47
2.2
3.3
4.7
10
22
33
47
100
5 11
220
330
6.3 11
470
8 11
1,000
10 13
8 11
10 16
5 11
63
(79)
5 11
5 11
6.3 11
6.3 11
6.3 11
100
(125)
5 11
5 11
5 11
6.3 11
50
(63)
6.3 11
8 11
10 13
8 11
10 16
6.3 11
8 11
8 11
10 13
13 21
8 11
10 13
10 16
10 21
16 26
10 21
13 21
16 26
13 21
13 26
16 32
16 26
16 32
18 42
10 13
10 16
10 21
10 16
13 21
www.element14.com
www.farnell.com
www.newark.com
Page <2>
17/04/12
V1.0
10
(13)
16
(20)
25
(32)
35
(44)
50
(63)
63
(79)
100
(125)
2,200
10 21
13 21
13 26
16 26
16 36
18 36
25 50
3,300
13 21
13 26
16 26
16 36
18 36
22 42
4,700
13 26
16 26
16 36
18 36
22 41
25 50
6,800
16 26
16 36
18 36
22 41
25 50
30 46
8,200
18 36
18 42
22 46
22 50
30 46
10,000
18 32
18 36
22 41
25 50
15,000
18 36
22 50
25 50
22,000
22 50
25 50
30 46
8,200
18 36
18 42
22 46
22 50
10,000
18 32
18 36
22 41
25 50
15,000
18 36
22 50
25 50
22,000
22 50
25 50
30 46
30 46
Dimensions : Millimetres
All blank voltage on sleeve marking is the same voltage as i i" point to.
W V (SV)
F
10
(13)
16
(20)
25
(32)
35
(44)
50
(63)
63
(79)
100
(125)
0.1-0.47
10
13
16
2.2
21
27
3.3
30
40
4.7
30
35
40
40
45
10
45
45
50
60
65
75
22
60
60
70
80
90
110
130
33
75
85
95
105
120
140
170
47
90
100
120
135
150
180
230
100
140
170
180
220
250
280
380
150
220
240
310
350
400
450
550
220
240
280
320
380
430
490
680
330
320
360
420
480
540
680
800
470
400
460
540
620
750
880
1,000
560
500
580
670
770
880
1,050
1,170
680
570
660
760
870
1,000
1,160
1,330
820
640
740
850
970
1,130
1,300
1,500
www.element14.com
www.farnell.com
www.newark.com
Page <3>
17/04/12
V1.0
10
(13)
16
(20)
25
(32)
35
(44)
50
(63)
63
(79)
100
(125)
1,000
660
760
900
1,040
1,260
1,400
1,970
2,200
1,050
1,250
1,460
1,700
1,900
2,460
3,390
3,300
1,340
1,620
1,800
2,060
2,180
3,270
4,700
1,720
1,960
2,150
2,280
3,380
3,800
6,800
2,060
2,250
2,400
3,490
4,110
4,500
8,200
2,520
2,870
3,420
3,780
4,150
10,000
2,640
2,980
3,710
4,170
4,300
15,000
3,120
3,890
4,270
22,000
4,010
4,410
4,500
Dimensions : Millimetres
Part Number
Description
Part Number
MCGPR10V107M5X11
MCGPR25V476M5X11
MCGPR10V227M6.3X11
MCGPR25V107M6.3X11
MCGPR10V477M8X11
MCGPR25V227M8X11
MCGPR10V108M8X14
MCGPR25V337M8X14
MCGPR10V228M10X21
MCGPR25V477M10X16
MCGPR10V478M13X26
MCGPR25V108M10X21
MCGPR16V106M5X11
MCGPR25V228M13X26
MCGPR16V226M5X11
MCGPR25V338M16X26
MCGPR16V336M5X11
MCGPR25V478M16X32
MCGPR16V476M5X11
MCGPR35V475M5X11
MCGPR16V107M6.3X11
MCGPR35V106M5X11
MCGPR16V227M6.3X11
MCGPR35V226M5X11
MCGPR16V337M8X11
MCGPR35V336M5X11
MCGPR16V477M8X11
MCGPR35V476M6.3X11
MCGPR16V108M10X16
MCGPR35V107M8X11
MCGPR16V228M13X21
MCGPR35V227M10X13
MCGPR16V338M13X26
MCGPR35V337M10X16
MCGPR16V478M16X26
MCGPR35V477M10X21
MCGPR25V106M5X11
MCGPR35V108M13X21
MCGPR25V226M5X11
MCGPR35V228M16X32
MCGPR25V336M5X11
MCGPR35V338M16X32
www.element14.com
www.farnell.com
www.newark.com
Page <4>
17/04/12
V1.0
Part Number
Description
Part Number
MCGPR35V478M18X36
MCGPR63V475M5X11
MCGPR50V474M5X11
MCGPR63V106M5X11
MCGPR50V105M5X11
MCGPR63V226M6.3X11
MCGPR50V225M5X11
MCGPR63V476M8X11
MCGPR50V335M5X11
MCGPR63V107M10X13
MCGPR50V475M5X11
MCGPR63V227M10X21
MCGPR50V106M5X11
MCGPR63V477M13X26
MCGPR50V226M5X11
MCGPR63V108M16X32
MCGPR50V336M6.3X11
MCGPR63V228M18X36
MCGPR50V476M6.3X11
MCGPR63V478M25X42
MCGPR50V107M8X11
MCGPR100V105M5X11
MCGPR50V227M10X16
MCGPR100V225M5X11
MCGPR50V337M10X21
MCGPR100V475M5X11
MCGPR50V477M13X21
MCGPR100V106M6.3X11
MCGPR50V108M16X26
MCGPR100V226M8X11
MCGPR50V228M16X32
MCGPR100V476M10X16
MCGPR50V338M18X33
MCGPR100V107M13X21
MCGPR50V478M22X41
MCGPR100V227M16X26
MCGPR63V105M5X11
MCGPR100V477M16X32
MCGPR63V225M5X11
Important Notice : This data sheet and its contents (the Information) belong to the members of the Premier Farnell group of companies (the Group) or are licensed to it. No licence is granted
for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any
error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any
assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the
Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Groups liability for death or personal injury resulting from its negligence.
Multicomp is the registered trademark of the Group. Premier Farnell plc 2012.
www.element14.com
www.farnell.com
www.newark.com
Page <5>
17/04/12
V1.0
WYP
INTERFERENCE SUPPRESSION CAPACITORS OF CLASS Y2 / 275 VAC
Cu wire
- tinned
0,8 0,1
Vac
Dimension
0,3
mm
18,0
20
Safety
approvals
Rated voltage
Capacitance
tolerance
Rated
capacitance
F
0,010
0,015
0,022
0,027
0,033
0,047
0,068
0,10
0,8 0,1
L
WYP-103M
WYP-153M
WYP-223M
WYP-273M
WYP-333M
WYP-473M
WYP-683M
WYP-104M
0,8 0,1
T/2 0,6 A
Code
Marking
area
Taped
H1
275
26,5
0,3
mm
10,5
12,5
13,5
14,5
17,0
15,5
16,5
18,5
H1
max
mm
12,5
14,5
15,5
16,5
19,0
0,3
mm
5,5
6,5
7,5
8,5
8,5
7,5
8,5
10,5
0,5
mm
15,0
22,5
EN 60384-14
275Vac
Approvals in use =
APPLICATION
The WYP interference suppression capacitors are designed to attenuate RFI signal in all and line-ground applications
for class Y2. Appropriate for use in situations where capacitor failure could cause an electric shock danger.
CONSTRUCTION
Non-inductive metallized polypropylene winding encapsulated in self-extinguishing material meeting the requirements
of UL 94 V-0.
REQUIREMENTS
The WYP capacitors meet the requirements of EN 60384-14 standard for class Y2.
SRC/M Series
Anti-Surge5HVLVWRr
MERITEK
)HDWXUHV
Replaces 1 and 2 watt carbon composition resistors.
Withstands high peak power and offers 10% tolerance
Withstands high energy density demands
3DUW1XPEHU6\VWHP
SRC/M
1/2W
VALUE
TR
$SSHDUDQFH
67</(
Standard
SRC1/2W
SRC1W
SRC2W
SRM1/2W
SRM1W
SRM2W
11.51.0
15.51.0
17.51.0
11.51.0
15.51.0
15.51.0
',0(16,21PP
'
4.50.5
5.00.5
6.50.5
4.50.5
5.00.5
5.00.5
352.0
322.0
352.0
352.0
322.0
352.0
5HVLVWDQFH5DQJH
0.780.03
10~10K10
0.780.03
3~9920
0.780.03
0.780.03
1K~1M10
0.780.03
0.780.03
&XUYHV
1
SRC/M Series
Anti-Surge5HVLVWRr
MERITEK
5DWLQJV
7<3(
SRC-1/2W
SRC-1W
SRC-2W
SRM-1/2W
SRM-1W
SRM-2W
32:(5
5$7,1*
1/2W
1W
2W
1/2W
1W
2W
0$;:25.,1*
0$;
82/
29(5/2$'82/
200V
300V
400V
200V
300V
400V
400V
600V
800V
400V
600V
800V
'LHOHFWULF
:LWKVWDQGLQJ
YROWDJH
500V
500V
500V
500V
500V
500V
0$;$17,
685*(
10KV
14KV
18KV
10KV
15KV
25KV
23(5$7,1*
7(035$1*(
40 to200
6SHFLILFDWLRQV
TEST CHARACTERISTICS
Test Methods
SPECIFICATIONS
TEMPERATURE
1.0%0.05
SRC10K= 300ppm
SRM 10K= 200ppm
Surge Voltage
Characteristics
(EN60065 TEST)
Load Life
1.0%0.05
5.0%0.05
Tensile strngth:2.5kg
5.0%0.05
CLD-CT1079.005
PRODUCT DESCRIPTION
FEATURES
APPLICATIONS
Size (mm): 5
These lamps are made with an advanced optical-grade epoxy offering
superior high-temperature and highmoisture-resistance performance in
WWW.CREE.COM/HB
Viewing angle:
C503B-RAS/RAN/AAS/AAN:
15 degree
C503B-RBS/RBN/ABS/ABN:
23 degree
C503B-RCS/RCN/ACS/ACN:
30 degree
Lead - Free
RoHS Compliant
Motorway Signs
Advertising signs
Petrol Signs
Amusement
Copyright 2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice.
the Cree logo are registered trademarks of Cree, Inc.
Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com/xlamp
Symbol
Unit
Red/Amber
Forward Current
Peak Forward Current
IF
50
mA
Note1
IFP
200
mA
Reverse Voltage
VR
Power Dissipation
PD
130
mW
Operation Temperature
Topr
-40 ~ +100
Storage Temperature
Tstg
-40 ~ +100
Tsol
ESD
Class 2
Note2
Electrostatic Discharge
Classification (MIL-STD-883E)
Note:
1. For long term performance the drive currents between 10mA and 30mA are recommended. Please contact CREE
sales representative for more information on recommended drive conditions.
2. Pulse width 0.1 msec, duty 1/10.
Color
Symbol
Condition
Unit
Forward Voltage
Red/Amber
VF
IF = 20 mA
Reverse Current
Red/Amber
IR
VR = 5 V
Red
IF = 20 mA
nm
Amber
Dominant Wavelength
Red
Luminous Intensity
Amber
Typical
Maximum
2.1
2.6
100
618
624
630
596
IF = 20 mA
nm
584
591
IV
IF = 20 mA
mcd
5860
12000
IV
IF = 20 mA
mcd
3000
5000
IV
IF = 20 mA
mcd
3000
5100
IV
IF = 20 mA
mcd
5860
13000
IV
IF = 20 mA
mcd
3000
5000
4180
6000
Minimum
IV
IF = 20 mA
mcd
C503B-RAS/RAN/AAS/AAN
IF = 20 mA
deg
15
C503B-RBS/RBN/ABS/ABN
IF = 20 mA
deg
23
C503B-RCS/RCN/ACS/ACN
IF = 20 mA
deg
30
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
Amber
Bin Code
Min. (mcd)
Max. (mcd)
Bin Code
Min. (mcd)
Max. (mcd)
Y0
5860
8200
Y0
5860
8200
Z0
8200
12000
Z0
8200
12000
A0
12000
16800
A0
12000
16800
B0
16800
23500
B0
16800
23500
Bin Code
Min. (mcd)
Max. (mcd)
Bin Code
Min. (mcd)
Max. (mcd)
W0
3000
4180
W0
3000
4180
X0
4180
5860
X0
4180
5860
Y0
5860
8200
Y0
5860
8200
Z0
8200
12000
Z0
8200
12000
Bin Code
Min. (mcd)
Max. (mcd)
Bin Code
Min. (mcd)
Max. (mcd)
W0
3000
4180
X0
4180
5860
X0
4180
5860
Y0
5860
8200
Y0
5860
8200
Z0
8200
12000
Z0
8200
12000
Red
Bin Code
RA
Min. (nm)
618
Max. (nm)
Bin Code
Min. (nm)
Max. (nm)
630
A2
584
587
A3
587
590
A4
590
593
A5
593
596
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
Viewing
Angle
Red
C503B-RAS-CY0B0AA1
Red
C503B-RAS-CZ0A0AA1
Red
Red
Red
C503B-RAN-CZ0A0AA1
Red
C503B-RAN-CA0B0AA1
Red
Red
Red
C503B-RAS-CA0B0AA2
Color
Dominant Wavelength
Min.
(nm)
Color
Bin
Max.
(nm)
Package
Standoff
Min.
Max.
Color
Bin
15
5860
23500
RA
618
RA
630
Bulk
Yes
15
8200
16800
RA
618
RA
630
Bulk
Yes
C503B-RAS-CA0B0AA1
15
12000
23500
RA
618
RA
630
Bulk
Yes
C503B-RAN-CY0B0AA1
15
5860
23500
RA
618
RA
630
Bulk
No
15
8200
16800
RA
618
RA
630
Bulk
No
15
12000
23500
RA
618
RA
630
Bulk
No
C503B-RAS-CY0B0AA2
15
5860
23500
RA
618
RA
630
Ammo
Yes
C503B-RAS-CZ0A0AA2
15
8200
16800
RA
618
RA
630
Ammo
Yes
15
12000
23500
RA
618
RA
630
Ammo
Yes
No
Red
C503B-RAN-CY0B0AA2
15
5860
23500
RA
618
RA
630
Ammo
Red
C503B-RAN-CZ0A0AA2
15
8200
16800
RA
618
RA
630
Ammo
No
Red
C503B-RAN-CA0B0AA2
15
12000
23500
RA
618
RA
630
Ammo
No
Kit Number
Viewing
Angle
Red
C503B-RBS-CW0Z0AA1
Red
C503B-RBS-CX0Y0AA1
Red
Red
Red
RA
Dominant Wavelength
Max.
Color
Bin
Min.
(nm)
Color
Bin
Max.
(nm)
Package
Standoff
23
3000
12000
RA
618
RA
630
Bulk
Yes
23
4180
8200
RA
618
RA
630
Bulk
Yes
C503B-RBS-CY0Z0AA1
23
5860
12000
RA
618
RA
630
Bulk
Yes
C503B-RBN-CW0Z0AA1
23
3000
12000
RA
618
RA
630
Bulk
No
C503B-RBN-CX0Y0AA1
23
4180
8200
RA
618
RA
630
Bulk
No
Red
C503B-RBN-CY0Z0AA1
23
5860
12000
RA
618
RA
630
Bulk
No
Red
C503B-RBS-CW0Z0AA2
23
3000
12000
RA
618
RA
630
Ammo
Yes
Red
C503B-RBS-CX0Y0AA2
23
4180
8200
RA
618
RA
630
Ammo
Yes
Red
C503B-RBS-CY0Z0AA2
23
5860
12000
RA
618
RA
630
Ammo
Yes
Red
C503B-RBN-CW0Z0AA2
23
3000
12000
RA
618
RA
630
Ammo
No
Red
C503B-RBN-CX0Y0AA2
23
4180
8200
RA
618
RA
630
Ammo
No
Red
C503B-RBN-CY0Z0AA2
23
5860
12000
RA
618
RA
630
Ammo
No
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
Kit Number
Viewing
Angle
Red
C503B-RCS-CW0Z0AA1
Red
C503B-RCS-CW0X0AA1
Red
Red
Red
Dominant Wavelength
Min.
(nm)
Color
Bin
Max.
(nm)
Package
Standoff
Min.
Max.
Color
Bin
30
3000
12000
RA
618
RA
630
Bulk
Yes
30
3000
5860
RA
618
RA
630
Bulk
Yes
C503B-RCS-CX0Y0AA1
30
4180
8200
RA
618
RA
630
Bulk
Yes
C503B-RCN-CW0Z0AA1
30
3000
12000
RA
618
RA
630
Bulk
No
C503B-RCN-CW0X0AA1
30
3000
5860
RA
618
RA
630
Bulk
No
Red
C503B-RCN-CX0Y0AA1
30
4180
8200
RA
618
RA
630
Bulk
No
Red
C503B-RCS-CW0Z0AA2
30
3000
12000
RA
618
RA
630
Ammo
Yes
Red
C503B-RCS-CW0X0AA2
30
3000
5860
RA
618
RA
630
Ammo
Yes
Red
C503B-RCS-CX0Y0AA2
30
4180
8200
RA
618
RA
630
Ammo
Yes
Red
C503B-RCN-CW0Z0AA2
30
3000
12000
RA
618
RA
630
Ammo
No
Red
C503B-RCN-CW0X0AA2
30
3000
5860
RA
618
RA
630
Ammo
No
Red
C503B-RCN-CX0Y0AA2
30
4180
8200
RA
618
RA
630
Ammo
No
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
Viewing
Angle
Amber
C503B-AAS-CY0B0251
Amber
C503B-AAS-CZ0B0341
Amber
Amber
Amber
C503B-AAN-CZ0B0341
Amber
C503B-AAN-CA0B0341
Amber
Amber
Amber
Color
Dominant Wavelength
Min.
(nm)
Color
Bin
Max.
(nm)
Package
Standoff
Min.
Max.
Color
Bin
15
5860
23500
A2
584
A5
596
Bulk
Yes
15
8200
23500
A3
587
A4
593
Bulk
Yes
C503B-AAS-CA0B0341
15
12000
23500
A3
587
A4
593
Bulk
Yes
C503B-AAN-CY0B0251
15
5860
23500
A2
584
A5
596
Bulk
No
15
8200
23500
A3
587
A4
593
Bulk
No
15
12000
23500
A3
587
A4
593
Bulk
No
C503B-AAS-CY0B0252
15
5860
23500
A2
584
A5
596
Ammo
Yes
C503B-AAS-CZ0B0342
15
8200
23500
A3
587
A4
593
Ammo
Yes
C503B-AAS-CA0B0342
15
12000
23500
A3
587
A4
593
Ammo
Yes
Amber
C503B-AAN-CY0B0252
15
5860
23500
A2
584
A5
596
Ammo
No
Amber
C503B-AAN-CZ0B0342
15
8200
23500
A3
587
A4
593
Ammo
No
Amber
C503B-AAN-CA0B0342
15
12000
23500
A3
587
A4
593
Ammo
No
Kit Number
Viewing
Angle
Amber
C503B-ABS-CW0Z0251
Amber
C503B-ABS-CX0Y0341
Amber
Amber
Amber
C503B-ABN-CX0Y0341
23
Amber
C503B-ABN-CY0Z0341
23
Amber
C503B-ABS-CW0Z0252
23
Amber
C503B-ABS-CX0Y0342
23
Amber
C503B-ABS-CY0Z0342
Amber
C503B-ABN-CW0Z0252
Amber
Amber
Dominant Wavelength
Min.
(nm)
Color
Bin
Max.
(nm)
Package
Standoff
Min.
Max.
Color
Bin
23
3000
12000
A2
584
A5
596
Bulk
Yes
23
4180
8200
A3
587
A4
593
Bulk
Yes
C503B-ABS-CY0Z0341
23
5860
12000
A3
587
A4
593
Bulk
Yes
C503B-ABN-CW0Z0251
23
3000
12000
A2
584
A5
596
Bulk
No
4180
8200
A3
587
A4
593
Bulk
No
5860
12000
A3
587
A4
593
Bulk
No
3000
12000
A2
584
A5
596
Ammo
Yes
4180
8200
A3
587
A4
593
Ammo
Yes
23
5860
12000
A3
587
A4
593
Ammo
Yes
23
3000
12000
A2
584
A5
596
Ammo
No
C503B-ABN-CX0Y0342
23
4180
8200
A3
587
A4
593
Ammo
No
C503B-ABN-CY0Z0342
23
5860
12000
A3
587
A4
593
Ammo
No
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
Kit Number
Viewing
Angle
Amber
C503B-ACS-CX0Z0251
Amber
C503B-ACS-CX0Z0341
Amber
Amber
Amber
Dominant Wavelength
Min.
(nm)
Color
Bin
Max.
(nm)
Package
Standoff
Min.
Max.
Color
Bin
30
4180
12000
A2
584
A5
596
Bulk
Yes
30
4180
12000
A3
587
A4
593
Bulk
Yes
C503B-ACS-CX0Y0251
30
4180
8200
A2
584
A5
596
Bulk
Yes
C503B-ACS-CX0Y0341
30
4180
8200
A3
587
A4
593
Bulk
Yes
C503B-ACS-CY0Z0251
30
5860
12000
A2
584
A5
596
Bulk
Yes
Amber
C503B-ACS-CY0Z0341
30
5860
12000
A3
587
A4
593
Bulk
Yes
Amber
C503B-ACN-CX0Z0251
30
4180
12000
A2
584
A5
596
Bulk
No
Amber
C503B-ACN-CX0Z0341
30
4180
12000
A3
587
A4
593
Bulk
No
Amber
C503B-ACN-CX0Y0251
30
4180
8200
A2
584
A5
596
Bulk
No
Amber
C503B-ACN-CX0Y0341
30
4180
8200
A3
587
A4
593
Bulk
No
Amber
C503B-ACN-CY0Z0251
30
5860
12000
A2
584
A5
596
Bulk
No
Amber
C503B-ACN-CY0Z0341
30
5860
12000
A3
587
A4
593
Bulk
No
Amber
C503B-ACS-CX0Z0252
30
4180
12000
A2
584
A5
596
Ammo
Yes
Amber
C503B-ACS-CX0Z0342
30
4180
12000
A3
587
A4
593
Ammo
Yes
Amber
C503B-ACS-CX0Y0252
30
4180
8200
A2
584
A5
596
Ammo
Yes
Amber
C503B-ACS-CX0Y0342
30
4180
8200
A3
587
A4
593
Ammo
Yes
Amber
C503B-ACS-CY0Z0252
30
5860
12000
A2
584
A5
596
Ammo
Yes
Amber
C503B-ACS-CY0Z0342
30
5860
12000
A3
587
A4
593
Ammo
Yes
Amber
C503B-ACN-CX0Z0252
30
4180
12000
A2
584
A5
596
Ammo
No
Amber
C503B-ACN-CX0Z0342
30
4180
12000
A3
587
A4
593
Ammo
No
Amber
C503B-ACN-CX0Y0252
30
4180
8200
A2
584
A5
596
Ammo
No
Amber
C503B-ACN-CX0Y0342
30
4180
8200
A3
587
A4
593
Ammo
No
Amber
C503B-ACN-CY0Z0252
30
5860
12000
A2
584
A5
596
Ammo
No
Amber
C503B-ACN-CY0Z0342
30
5860
12000
A3
587
A4
593
Ammo
No
Notes:
1. The above kit numbers represent order codes that include multiple intensity-bin and color-bin codes. Only one
intensity-bin code and one color-bin code will be shipped on each bulk. Single intensity-bin code and single color-bin
codes will not be orderable.
2. Please refer to the Cree LED Lamp Reliability Test Standards document for reliability test conditions.
3. Please refer to the Cree LED Lamp Soldering & Handling document for information about how to use this LED
product safely.
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
GRAPHS
100.0
IF (mA)
5.0
80.0
4.0
60.0
3.0
Amber
Red
40.0
2.0
20.0
Amber
1.0
0.0
1.8
VF(V)
2.0
2.2
2.4
2.6
2.8
-60
-50
-40
-30
-20
0.0
0.0
20
40
60
80
IF(mA)
100
Vr(V)
Red
-10
100%
-10
80%
-20
60%
-30
40%
-40
20%
Amber
-50
Ir(uA)
FIG.3 RED & AMBER REVERSE CURRENT
VS. REVERSE VOLTAGE.
0%
300
400
500
Red
600
700
WL(nm)
800
IF(mA)
100
80
60
40
20
Ta( C)
40
20
60
80
100
0
FIG.5 RED & AMBER MAXIMUM FORWARD
DC CURRENT VS AMBIENT
TEMPERATURE (Tjmax=110 C)
0
The above data are collected from statistical figures that do not necessarily correspond to the actual
parameters of each single LED. Hence, these data will be changed without further notice.
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
GRAPHS
The above data are collected from statistical figures that do not necessarily correspond to the actual
parameters of each single LED. Hence, these data will be changed without further notice.
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
MECHANICAL DIMENSIONS
All dimensions are in mm. Tolerance is 0.25 mm unless otherwise noted.
An epoxy meniscus may extend about 1.5 mm down the leads.
Burr around bottom of epoxy may be 0.5 mm max.
C503B-RAS/AAS:
C503B-RBS/ABS:
C503B-RCS:
C503B-ACS:
NOTES
RoHS Compliance
The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/
EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as
amended through April 21, 2006.
Vision Advisory Claim
Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
10
MECHANICAL DIMENSIONS
All dimensions are in mm. Tolerance is 0.25 mm unless otherwise noted.
An epoxy meniscus may extend about 1.5 mm down the leads.
Burr around bottom of epoxy may be 0.5 mm max.
C503B-RAN/AAN/RCN:
C503B-RBN/ABN:
C503B-ACN:
NOTES
RoHS Compliance
The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/
EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as
amended through April 21, 2006.
Vision Advisory Claim
Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
11
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
12
PACKAGING
Features:
The LEDs are packed in cardboard boxes after packaging in normal or anti-electrostatic bags.
Cardboard boxes will be used to protect the LEDs from mechanical shock during transportation.
The boxes are not water resistant, and they must be kept away from water and moisture.
The Bulk Pack types of packaging.
Max 500 pcs per bulk and Max 2500 pcs per ammo.
xxx xxx
R
LOT
JOWAXXXXX -XX-XXX
QTY
RANK
PCS
Iv
Vf
XX
Hue
XX
AXXXXXXXXXXX
ANODE
Label
(anti-electrostatic
bag)
xxx xxx
LOT
JOWAXXXXX -XX-XXX
QTY
RANK
PCS
Iv
Vf
Hue
20 bags/carton
XX
XX
AXXXXXXXXXXX
Copyright 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
Copyright
2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
of Cree, Inc.
13
Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
LM555 Timer
1 Features
3 Description
2 Applications
Precision Timing
Pulse Generation
Sequential Timing
Time Delay Generation
Pulse Width Modulation
Pulse Position Modulation
Linear Ramp Generator
Device Information(1)
PART NUMBER
LM555
PACKAGE
SOIC (8)
4.90 mm 3.91 mm
PDIP (8)
9.81 mm 6.35 mm
VSSOP (8)
3.00 mm 3.00 mm
Schematic Diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
6
4 Revision History
Changes from Revision C (March 2013) to Revision D
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Page
Page
LM555
www.ti.com
GND
2
TRIGGER
OUTPUT
COMPARATOR
FLIP FLOP
OUTPUT
STAGE
DISCHARGE
COMPARATOR
VREF (INT)
RESET
+VCC
THRESHOLD
CONTROL
VOLTAGE
Pin Functions
PIN
NO.
NAME
Control
Voltage
Discharge
I/O
DESCRIPTION
Controls the threshold and trigger levels. It determines the pulse width of the output
waveform. An external voltage applied to this pin can also be used to modulate the output
waveform
Open collector output which discharges a capacitor between intervals (in phase with output).
It toggles the output from high to low when voltage reaches 2/3 of the supply voltage
GND
Output
Negative pulse applied to this pin to disable or reset the timer. When not used for reset
purposes, it should be connected to VCC to avoid false triggering
Compares the voltage applied to the terminal with a reference voltage of 2/3 Vcc. The
amplitude of voltage applied to this terminal is responsible for the set state of the flip-flop
Responsible for transition of the flip-flop from set to reset. The output of the timer depends
on the amplitude of the external trigger pulse applied to this pin
4
6
2
8
Reset
Threshold
Trigger
V+
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
Power Dissipation (3)
Soldering
Information
MAX
UNIT
1180
mW
LM555CMM
613
mW
PDIP Package
260
215
220
150
65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
For operating at elevated temperatures the device must be derated above 25C based on a 150C maximum junction temperature and a
thermal resistance of 106C/W (PDIP), 170C/W (S0IC-8), and 204C/W (VSSOP) junction to ambient.
Refer to RETS555X drawing of military LM555H and LM555J versions for specifications.
Electrostatic discharge
VALUE
UNIT
500 (2)
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
The ESD information listed is for the SOIC package.
MAX
UNIT
18
70
70
PDIP
SOIC
VSSOP
UNIT
204
C/W
8 PINS
RJA
(1)
106
170
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
LM555
www.ti.com
TEST CONDITIONS
Supply Voltage
Supply Current
MIN
TYP
4.5
MAX
UNIT
16
VCC = 5 V, RL =
VCC = 15 V, RL =
(Low State) (3)
10
15
V
mA
1%
RA = 1 k to 100 k,
C = 0.1 F,
50
ppm/C
(4)
1.5 %
0.1 %
2.25
RA, RB =1 k to 100 k,
C = 0.1 F,
150
3.0%
0.30 %
Threshold Voltage
0.667
Trigger Voltage
VCC = 15 V
0.4
Reset Current
Control Voltage Level
VCC = 5 V
Pin 7 Leakage Output High
Pin 7 Sat
0.5
0.9
0.5
0.1
0.4
mA
0.1
0.25
10
11
2.6
3.33
100
(5)
VCC = 15 V
1.67
Trigger Current
Reset Voltage
/V
x VCC
VCC = 5 V
Threshold Current
ppm/C
(4)
V
nA
(6)
Output Low
VCC = 15 V, I7 = 15 mA
180
Output Low
80
200
mV
ISINK = 10 mA
0.1
0.25
ISINK = 50 mA
mV
VCC = 15 V
0.4
0.75
ISINK = 100 mA
2.5
ISINK = 200 mA
2.5
VCC = 5 V
ISINK = 8 mA
ISINK = 5 mA
(1)
(2)
(3)
(4)
(5)
(6)
V
0.25
0.35
All voltages are measured with respect to the ground pin, unless otherwise specified.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate
conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC
electrical specifications under particular test conditions which ensures specific performance limits. This assumes that the device is within
the Recommended Operating Conditions. Specifications are not ensured for parameters where no limit is given, however, the typical
value is a good indication of device performance.
Supply current when output high typically 1 mA less at VCC = 5 V.
Tested at VCC = 5 V and VCC = 15 V.
This will determine the maximum value of RA + RB for 15 V operation. The maximum total (RA + RB) is 20 M.
No protection against excessive pin 7 current is necessary providing the package dissipation rating will not be exceeded.
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
TEST CONDITIONS
MIN
TYP
MAX
UNIT
12.5
12.75
13.3
2.75
3.3
100
ns
100
ns
LM555
www.ti.com
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are
provided for triggering or resetting if desired. In the time delay mode of operation, the time is precisely controlled
by one external resistor and capacitor. For astable operation as an oscillator, the free running frequency and duty
cycle are accurately controlled with two external resistors and one capacitor. The circuit may be triggered and
reset on falling waveforms, and the output circuit can source or sink up to 200mA or driver TTL circuits. The
LM555 are available in 8-pin PDIP, SOIC, and VSSOP packages and is a direct replacement for SE555/NE555.
CONTROL
THRESHOLD VOLTAGE
+Vcc
COMPARATOR
RESET
Vref (int)
TRIGGER
FLIP FLOP
DISCHARGE
COMPARATOR
OUTPUT
STAGE
OUTPUT
LM555
www.ti.com
capacitor equals 2/3 of the supply voltage. The output pulse width can be extended or shortened depending
on the application by adjusting the R and C values.
Astable (free-running) mode: The LM555 timer can operate as an oscillator and puts out a continuous stream
of rectangular pulses having a specified frequency. The frequency of the pulse stream depends on the values
of RA, RB, and C.
VCC = 5 V
TIME = 0.1 ms/DIV.
RA = 9.1 k
C = 0.01 F
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
10
LM555
www.ti.com
VCC = 5 V
TIME = 20s/DIV.
RA = 3.9 k
RB = 3 k
C = 0.01 F
(1)
(2)
(3)
11
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
(6)
12
LM555
www.ti.com
VCC = 5 V
Top Trace: Input 4 V/Div.
TIME = 20 s/DIV. Middle Trace: Output 2V/Div.
RA = 9.1 k
Bottom Trace: Capa citor 2V/Div.
C = 0.01 F
13
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
Figure 19. Trigger, Capacitor Voltage, and Output Waveforms in Monostable Mode
14
LM555
www.ti.com
10 Layout
10.1 Layout Guidelines
Standard PCB rules apply to routing the LM555. The 0.1-F capacitor in parallel with a 1-F electrolytic capacitor
should be as close as possible to the LM555. The capacitor used for the time delay should also be placed as
close to the discharge pin. A ground plane on the bottom layer can be used to provide better noise immunity and
signal integrity.
Figure 20 is the basic layout for various applications.
C1 based on time delay calculations
C2 0.01-F bypass capacitor for control voltage pin
C3 0.1-F bypass ceramic capacitor
C4 1-F electrolytic bypass capacitor
R1 based on time delay calculations
U1 LMC555
15
LM555
SNAS548D FEBRUARY 2000 REVISED JANUARY 2015
www.ti.com
11.3 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
16
www.ti.com
17-Feb-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Eco Plan
Lead/Ball Finish
(2)
(6)
(3)
Op Temp (C)
Device Marking
(4/5)
LM555CM
NRND
SOIC
95
TBD
Call TI
Call TI
0 to 70
LM
555CM
LM555CM/NOPB
ACTIVE
SOIC
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM
555CM
LM555CMM
NRND
VSSOP
DGK
1000
TBD
Call TI
Call TI
0 to 70
Z55
LM555CMM/NOPB
ACTIVE
VSSOP
DGK
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
Z55
LM555CMMX/NOPB
ACTIVE
VSSOP
DGK
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
Z55
LM555CMX
NRND
SOIC
2500
TBD
Call TI
Call TI
0 to 70
LM
555CM
LM555CMX/NOPB
ACTIVE
SOIC
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM
555CM
LM555CN
OBSOLETE
PDIP
TBD
Call TI
Call TI
0 to 70
LM
555CN
LM555CN/NOPB
ACTIVE
PDIP
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
0 to 70
LM
555CN
MC1455P1
OBSOLETE
PDIP
TBD
Call TI
Call TI
0 to 70
LM
555CN
NE555V
OBSOLETE
PDIP
TBD
Call TI
Call TI
0 to 70
LM
555CN
40
(1)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
Samples
www.ti.com
17-Feb-2015
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
21-Oct-2014
Device
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM555CMM
VSSOP
DGK
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM555CMM/NOPB
VSSOP
DGK
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM555CMMX/NOPB
VSSOP
DGK
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM555CMX
SOIC
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM555CMX/NOPB
SOIC
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
21-Oct-2014
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM555CMM
VSSOP
DGK
1000
210.0
185.0
35.0
LM555CMM/NOPB
VSSOP
DGK
1000
210.0
185.0
35.0
LM555CMMX/NOPB
VSSOP
DGK
3500
367.0
367.0
35.0
LM555CMX
SOIC
2500
367.0
367.0
35.0
LM555CMX/NOPB
SOIC
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as components) are sold subject to TIs terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TIs terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TIs goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or enhanced plastic are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
www.ti.com/automotive
Amplifiers
amplifier.ti.com
www.ti.com/communications
Data Converters
dataconverter.ti.com
www.ti.com/computers
DLP Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
www.ti.com/energy
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
www.ti.com/video
RFID
www.ti-rfid.com
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2015, Texas Instruments Incorporated