Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Secc1 0 PDF
Secc1 0 PDF
INTRODUCCION
INTRODUCTION
!!!!!!EN CHAROLAS
SEGUIMOS SIENDO LA MEJOR OPCION
RECUBRIMIENTOS PROTECTORES
Debido a la naturaleza energtica de los metales, en
ambientes donde se presentan condiciones galvnicas
(humedad, agua salda, etc) o exposicin a qumicos
corrosivos, la aplicacin de recubrimientos anticorrosivos
aumentar la vida til de los materiales. El sistema de
soportera para cables de SOPORTES ELECTRICOS
puede ser suministrado con los siguientes recubrimientos
protectores:
1.- Para productos de acero al carbono :
Galvanizado por inmersin en caliente despus de
manufactura segn ASTM A 123
Galvanizado por inmersin en caliente antes de
manufactura segn ASTM A 525
Galvanizado electroltico segn ASTM B 633
Tropicalizado
Recubrimiento de PVC segn NEMA RN 1
Acabado epxico
Nota : el acero al carbono no se surte en acabado natural
2.- Para productos de aluminio:
Acabado natural (oxidacin protectora natural)
Recubrimiento de PVC segn NEMA RN 1
Acabado epxico
Los productos de acero inoxidable se surten en acabado
natural.
MANUFACTURING MATERIALS
The SOPORTES ELECTRICOS cable tray systems is made
with high quality materials, all our suppliers are ISO 9000
certificated, also the materials are strictly inspected in our
facilities for provide to you a product acordig with your
needes of quality and excelence.
The manufacturing materials should be carefull selected, for
this we recomend consult our published by Manual de
seleccin correcta de un sistema de soportera para
cables SOPORTES ELECTRICOS.
The available materials for cable tray systems are :
Carbon steel AISI C 1010 HR/CR
Stainless steel AISI-304
Aluminum AA 6063.
Polyester fiber glass reinforced flame-retardante, autoextinguish and protected against UV
FINISHES
The enviroment where a galvanic condition ( humidity, salt
water,etc.) or corrosive chemical exposure is present; the
aplication of corrosion proof finish is required for plus the
lifetime of the product. The SOPORTES ELECTRICOS
cable tray systems is available in the next protective
finishes
1.- For carbon steel products :
Hot dip galvanized after manufacture under ASTM A 123
Hot dip galvanized before manufacture under ASTM A
525
Electrogalvanized under ASTM B 633
Chromium-zinc coat
PVC coat under NEMA RN 1
Epoxy coat
The carbon steel products are not available in natural finish
2.- For aluminum products
Natural finish (a coat of natural Al O)
PVC coat under NEMA RN 1
Epoxy coat
The stainless steel products are availabe in natural finish.
For special coatings please consult our Technical
Department.
!!!!!!EN CHAROLAS
SEGUIMOS SIENDO LA MEJOR OPCION
LOAD CAPACITY
DAP
DAP
The support span acepted for the clasification are the follow :
5 for 5 feet (1.52 m)
6 for 6 feet (1.83 m)
8 for 8 feet (2.44 m)
12 for 12 feet (3.66 m)
16 for 16 feet (4.87 m)
20 for 20 feet (6.10 m)
The working loads acepted for the clasification are the follow :
AA for 12.5 Lb/ft (18.6 kg/m)
BB for 25 Lb/ft (37.2 kg/m)
A for 50 Lb/ft (74.4 kg/m)
B for 75 Lb/ft (111.6 kg/m)
C for 100 Lb/ft (148.8 kg/m)
Example : a NEMA 12C cable tray systems support a working
load of 100 Lb/ft (148.8 kg/m) when the support span is 12 ft
(3.66 m).
The working load is equivalent to the destruction load divided
by a safety factor of 1.5
A concentrated static load is not included in load/span
designations but if it is required for the user it should be
applicated at the center of the span if the combinated load
exceeds the working load, SOPORTES ELECTRICOS
should be consulted
(45)
2
5
13
(45)
8 (90)
(90)
12
10
4
11
9.- T VERTICAL
VERTICAL TEE
4.- CONECTOR
SPLICE PLATE
5.- CURVA HORIZONTAL
HORIZONTAL BEND
6.- T HORIZONTAL
HORIZONTAL TEE
10.- REDUCCION
REDUCER
11.- CONECTOR DE CHAROLA A CAJA
FRAME TYPE BOX CONNECTOR
12.- BARRERA SEPARADORA
BARRIER STRIP STRAIGHT SECTION
13.- TAPAS (CUBIERTAS)
COVERS