Documentos de Académico
Documentos de Profesional
Documentos de Cultura
DISEÑO ESTRUCTURAL
ESTACION
CMED LA ESTRELLA LA INMACULADA
1. ESPECIFICACIONES
1.1 ESPECIFICACIÓN GENERAL
La torre por instalar está ubicada en la carrera 55 con calle 95ª – Sur en el
municipio de Medellín, Departamento de Antioquia
Coordenadas
Consideraciones de Diseño
Categoría de riesgo II
Categoría de Exposición C
Categoría de Topografía 2
Altura de cresta 17 m
MATERIALES:
CONDICIONES DE CARGA
Tipo de Area de Altura de
Largo Ancho Profund.
Antena Cantidad Exposicion Radiacion
(mm) (mm) (mm)
(m2) (m)
Panel RF 8 2000 420 180 6.72 12
Modulo RRU 16 400 300 100 1.92 12
MW 1 Diámetro de 0.90 m 0.64 10
Total 9.28 m2
VERTICALIDAD TORRE
GIRO TORSIONAL
ESBELTEZ
CARGAS MUERTAS
Para el análisis de las cargas muertas se tiene en cuenta las cargas producidas
por antenas celulares, antenas microondas, escalera de ascenso, escalera de guía
onda, soportes de antenas, plataformas de trabajo y plataformas de descanso así:
Pararrayos (incluye soporte y cable de descarga) 30.00 kg
Escalera de Ascenso (incluye aditamentos LV) 12.50 kg/m.
Escalera de Guía Onda. 12.50 kg/m.
Soporte de diversidad: 610 kg
CARGA VIVA
FW= FST+FA+FG
Donde:
FST = Fuerza de viento de diseño sobre la estructura de acuerdo con 2.6.11.1
FA = Fuerza de viento de diseño sobre los accesorios de acuerdo con 2.6.11.2
FG = Fuerza de viento de diseño sobre las riendas de acuerdo con 2.6.11.3
La fuerza del viento de diseño, FST, aplicada a cada sección de una estructura se
determinará de acuerdo con lo siguiente:
FST = qz Gh (EPA) S
dónde:
FST = fuerza de viento de diseño horizontal sobre la estructura en la dirección
del viento
qz = presión de velocidad desde 2.6.11.6
Gh = factor de efecto de ráfaga de 2.6.9
(EPA) S = área proyectada efectiva de la estructura desde 2.6.11.1.1 o 2.6.11
Gh = Factor de respuesta de ráfaga
Gh = 0.85 +0.15/(h/45.7)-3.0)h en metros
0.85 < Gh < 1.00
h = Altura total de la estructura (m)
Para la incidencia oblicua del viento, según ANSI, el área neta oblicua será:
Anob = Cob*An
Donde: Cob = 0.75 incidencia a 60 grados
Cob = 1.00 incidencia normal
HIPOTESIS DE CARGA
Load Combinations
Com Description
b.
No.
1 Dead Only
2 1.2 Dead+1.0 Wind 0 deg - No Ice
3 0.9 Dead+1.0 Wind 0 deg - No Ice
4 1.2 Dead+1.0 Wind 45 deg - No Ice
5 0.9 Dead+1.0 Wind 45 deg - No Ice
6 1.2 Dead+1.0 Wind 90 deg - No Ice
7 0.9 Dead+1.0 Wind 90 deg - No Ice
8 1.2 Dead+1.0 Wind 180 deg - No Ice
9 0.9 Dead+1.0 Wind 180 deg - No Ice
10 Dead+Wind 0 deg - Service
11 Dead+Wind 45 deg - Service
12 Dead+Wind 90 deg - Service
13 Dead+Wind 180 deg - Service
r r
H=l2 M H=l2 M
12 1 1 1 1 1 1
2RRU 0.40X0.30
H=12 M □
3RRU 0.40X0.30
□
3RRU 0.40X0.30
11 H=l2 M H=l2 M
ANT. MW
10 (] D=0.90m.
H=10 M
09
08
07
06
05
04
03
02
01
CARA B CARA C CARA D
00
MONT-8 MONT-C MONT-D
CALCULO: FECHA:
WOM ESTACION: CMED LA ESTRELLA LA INMACULADA
TORRE CUADRADA DE 12 M SECCION 1.0x1.0 m lng Jaime Gutiérrez Junio 13-2023
COHIIIA!ISíA:
CONTIENE: DIBUJO: REV.
UBICACACION DE ANTENAS M. C. Beta. O
(2)soportes
(3)
Operarios
3
SPF3-52
Panel
Moduleantenna
Mantenimiento
de
RRUdiversidad
DESIGNED
400x300x100
2000x420x180 12
10
APPURTENANCE LOADING
12.0 m TYPE ELEVATION TYPE ELEVATION
(2) Panel antenna 2000x420x180 12 (2) Module RRU 400x300x100 12
(3) Panel antenna 2000x420x180 12 (3) Module RRU 400x300x100 12
(3) Panel antenna 2000x420x180 12 (3) Module RRU 400x300x100 12
(2) Module RRU 400x300x100 12 Operarios Mantenimiento 12
(3) Module RRU 400x300x100 12 3 soportes de diversidad 12
(3) Module RRU 400x300x100 12 SPF3-52 10
MATERIAL STRENGTH
GRADE Fy Fu GRADE Fy Fu
A572-50 345 MPa 448 MPa
L51x51x3
L51x51x3
L38x38x3
A572-50
A572-50
12 @ 1
6.0 m
1
389.0
T2
ALL REACTIONS
ARE FACTORED
UPLIFT: -21353 kg
SHEAR: 1477 kg
AXIAL
3399 kg
SHEAR MOMENT
4000 kg 30600 kg-m
0.0 m
TORQUE 1086 kg-m
778.1
# Panels @ (m)
Face Width (m)
Weight (kg)
Horizontals
Leg Grade
Diagonals
Top Girts
Section
Legs
Job:
INGEMEC SAS ESTACION: CMED LA ESTRELLA LA INMACULADA
Project: TORRE
Av Troncal de Occ No 18-76 CUADRADA DE 12 m SECCION 1.0x1.0m
Client: Drawn by: App'd:
Mosquera - Colombia WOM Ing Jaime Gutierrez
Code: Date: Scale:
JG Ingenieria Phone: (601) 893 9874 TIA-222-H 06/12/23 NTS
Path: Dwg No.
FAX: (601) 893 9874 E-1
D:\JG Ingenieria\Ingemec Asociados\WOM Torres\14 CMED La Estrella La Inmaculada TTA 12 m\tnx Tower CMED La Estrella La Inmaculada\tnx tower TTA 12 m CMED La Estrella La Inmaculada.eri
Stress Distribution Chart
0.00 - 12.00
> 100% 90%-100% 75%-90% 50%-75% < 50% Overstress
6.00 6.00
0.00 0.00
Job:
INGEMEC SAS ESTACION: CMED LA ESTRELLA LA INMACULADA
Project: TORRE
Av Troncal de Occ No 18-76 CUADRADA DE 12 m SECCION 1.0x1.0m
Client: Drawn by: App'd:
Mosquera - Colombia WOM Ing Jaime Gutierrez
Code: Date: Scale:
JG Ingenieria Phone: (601) 893 9874 TIA-222-H 06/12/23 NTS
Path: Dwg No.
FAX: (601) 893 9874 E-8
D:\JG Ingenieria\Ingemec Asociados\WOM Torres\14 CMED La Estrella La Inmaculada TTA 12 m\tnx Tower CMED La Estrella La Inmaculada\tnx tower TTA 12 m CMED La Estrella La Inmaculada.eri
TIA-222-H - Service - 97 kph Maximum Values
6.00 6.00
0.00 0.00
Job:
INGEMEC SAS ESTACION: CMED LA ESTRELLA LA INMACULADA
Project: TORRE
Av Troncal de Occ No 18-76 CUADRADA DE 12 m SECCION 1.0x1.0m
Client: Drawn by: App'd:
Mosquera - Colombia WOM Ing Jaime Gutierrez
Code: Date: Scale:
JG Ingenieria Phone: (601) 893 9874 TIA-222-H 06/12/23 NTS
Path: Dwg No.
FAX: (601) 893 9874 E-5
D:\JG Ingenieria\Ingemec Asociados\WOM Torres\14 CMED La Estrella La Inmaculada TTA 12 m\tnx Tower CMED La Estrella La Inmaculada\tnx tower TTA 12 m CMED La Estrella La Inmaculada.eri
Project: TORRE CUADRADA DE 12 m SECCION 1.0x1.0m
Job: ESTACION: CMED LA ESTRELLA LA INMACULADA
Client: WOM
LC:13 Dead+Wind 180 deg - Service
Max. Disp.29 mm @ 12.00 m
Scaling 20
Calculo: Ing. Jaime Gutierrez C: ESTACION
Fecha: junio 12 de 2023 CMED LA ESTRELLA LA INMACULADA
ESTRUCTURA: TORRE CUADRADA DE 12 m SECCION 1,0x1,0 m
CARGAS ACTUANTES
Tension Maxima T (ton)
Comprexion Maxima C (ton)
Fuerza Longitudinal en X Hx (ton)
Fuerza Transversal en Y Hy (ton)
B m
n
t
Dp
2
Area Placa Colocada Ac cm
Acero A-36 Fy= Kg /cm² Concreto. f'c= Kg / cm²
Distancia n cm
Area Requerida placa base Ar cm2
Apoyo contacto pedestal Fp Kg / cm²
Presion de Apoyo pp kg / cm²
Esfuerzo de Flexion por Compresion Fb
Esfuerzo de Flexion Fb Kg / cm² Acero A-36
Distancia al borde m cm
Espesor Placa Base C t cm
Esfuerzo de Flexion por Arranque Fb¨
Distancia al perno Dp cm
Fuerza en el Perno Pt Ton
Momento de Flexion Mf Ton - cm
Espesor de la Placa Base Arr t cm
Espesor Minimo Placa Base t cm
Lado de la placa Base B mm
Espesor de la Placa Base t mm OK CUMPLE
Calculo: Ing. Jaime Gutierrez C:
Fecha: junio 12 de 2023 ESTACION
CMED LA ESTRELLA LA INMACULADA
Cargas de Trabajo
Fuerza de Arranque T ton
Fuerza de Cortante Vux ton
Fuerza de Cortante Vuy ton
Fuerza de Cortante Vu ton
Pernos a Colocar un
Diametro del Perno mm
The main tower is a 4x free standing tower with an overall height of 12.00 m above the ground line.
The base of the tower is set at an elevation of 0.00 m above the ground line.
The face width of the tower is 1.00 m at the top and 1.00 m at the base.
This tower is designed using the TIA-222-H standard.
The following design criteria apply:
1. Tower base elevation above sea level: 1847.00 m.
2. Basic wind speed of 150 kph.
3. Risk Category II.
4. Exposure Category C.
5. Simplified Topographic Factor Procedure for wind speed-up calculations is used.
6. Topographic Category: 2.
7. Crest Height: 17.00 m.
8. Deflections calculated using a wind speed of 97 kph.
9. Weld together tower sections have flange connections..
10. Connections use galvanized A325 bolts, nuts and locking devices. Installation per TIA/EIA-222 and AISC
Specifications..
11. Tower members are ''hot dipped'' galvanized in accordance with ASTM A123 and ASTM A153 Standards..
12. Welds are fabricated with AWS E60XX/E70XX electrodes..
13. All welded joints and connection flanges cerfitied for integrity an quality per AWS D1:1.
14. RF antennas feeders shall be 1-5/8'' and installe 8 feeders per side.
15. RRU modules must be in fiber optic and installed 16 feeders per side.
16. MW antennas feeders shall be 1/2'' and installed 1 feeders per side.
17. A non-linear (P-delta) analysis was used.
18. Pressures are calculated at each section.
19. Stress ratio used in tower member design is 1.
20. Local bending stresses due to climbing loads, feed line supports, and appurtenance mounts are not considered.
Options
Consider Moments - Legs Distribute Leg Loads As Uniform Use ASCE 10 X-Brace Ly Rules
Consider Moments - Horizontals Assume Legs Pinned √ Calculate Redundant Bracing Forces
Consider Moments - Diagonals √ Assume Rigid Index Plate Ignore Redundant Members in FEA
Use Moment Magnification √ Use Clear Spans For Wind Area √ SR Leg Bolts Resist Compression
√ Use Code Stress Ratios √ Use Clear Spans For KL/r √ All Leg Panels Have Same Allowable
√ Use Code Safety Factors - Guys √ Retension Guys To Initial Tension Offset Girt At Foundation
Escalate Ice Bypass Mast Stability Checks √ Consider Feed Line Torque
Always Use Max Kz √ Use Azimuth Dish Coefficients √ Include Angle Block Shear Check
Use Special Wind Profile √ Project Wind Area of Appurt. Use TIA-222-H Bracing Resist. Exemption
√ Include Bolts In Member Capacity √ Autocalc Torque Arm Areas Use TIA-222-H Tension Splice Exemption
√ Leg Bolts Are At Top Of Section Add IBC .6D+W Combination Poles
√ Secondary Horizontal Braces Leg Sort Capacity Reports By Component Include Shear-Torsion Interaction
Use Diamond Inner Bracing (4 Sided) √ Triangulate Diamond Inner Bracing Always Use Sub-Critical Flow
SR Members Have Cut Ends Treat Feed Line Bundles As Cylinder Use Top Mounted Sockets
SR Members Are Concentric Ignore KL/ry For 60 Deg. Angle Legs Pole Without Linear Attachments
Pole With Shroud Or No Appurtenances
Page
tnxTower
Job
ESTACION: CMED LA ESTRELLA LA INMACULADA 2 of 27
Project Date
TORRE CUADRADA DE 12 m SECCION 1.0x1.0m 06/12/23
Av Troncal de Occ No 18-76
Mosquera - Colombia Client Designed by
Phone: (601) 893 9874
FAX: (601) 893 9874 Ing Jaime Gutierrez
Leg A Leg B
Face B
Wind 90 X
Face A
Face C
Z
Face D
Leg D Leg C
45
d
in
W
Wind 0
Square Tower
K Factors1
Tower Calc Calc Legs X K Single Girts Horiz. Sec. Inner
Elevation K K Brace Brace Diags Horiz. Brace
Single Solid Diags Diags
Angles Rounds X X X X X X X
m Y Y Y Y Y Y Y
T1 12.00-6.00 No No 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
T2 6.00-0.00 No No 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
1
Note: K factors are applied to member segment lengths. K-braces without inner supporting members will have the K factor in the out-of-plane direction applied to
the overall length.
Shielding Factor Ka
Tower Feed Line Description Feed Line Ka Ka
Section Record No. Segment Elev. No Ice Ice
T1 1 Climbing Ladder 19.69 - 39.37 1.0000 1.0000
T2 1 Climbing Ladder 0.00 - 19.69 1.0000 1.0000
Page
tnxTower
Job
ESTACION: CMED LA ESTRELLA LA INMACULADA 6 of 27
Project Date
TORRE CUADRADA DE 12 m SECCION 1.0x1.0m 06/12/23
Av Troncal de Occ No 18-76
Mosquera - Colombia Client Designed by
Phone: (601) 893 9874
FAX: (601) 893 9874 Ing Jaime Gutierrez
Dishes
Page
tnxTower
Job
ESTACION: CMED LA ESTRELLA LA INMACULADA 7 of 27
Project Date
TORRE CUADRADA DE 12 m SECCION 1.0x1.0m 06/12/23
Av Troncal de Occ No 18-76
Mosquera - Colombia Client Designed by
Phone: (601) 893 9874
FAX: (601) 893 9874 Ing Jaime Gutierrez
Description Face Dish Offset Offsets: Azimuth 3 dB Elevation Outside Aperture Weight
or Type Type Horz Adjustment Beam Diameter Area
Leg Lateral Width
Vert
m ° ° m m m2 kg
SPF3-52 C Paraboloid w/o From 0.60 0.0000 10.00 0.91 No Ice 0.66 16
Radome Leg 0.00
0.00
Force Totals
Load Vertical Sum of Sum of Sum of Sum of Sum of Torques
Case Forces Forces Forces Overturning Overturning
X Z Moments, Mx Moments, Mz
kg kg kg kg-m kg-m kg-m
Leg Weight 403
Bracing Weight 376
Total Member Self-Weight 778 509 -1
Total Weight 2833 509 -1
Wind 0 deg - No Ice 59 -3729 -28215 -878 -544
Wind 45 deg - No Ice 2854 -2803 -20950 -22075 385
Wind 90 deg - No Ice 3734 -72 -357 -28857 1083
Wind 180 deg - No Ice -27 3715 29145 326 489
Total Weight 2833 509 -1
Wind 0 deg - Service 16 -1548 -11684 -444 -225
Wind 45 deg - Service 1174 -1164 -8673 -9228 160
Wind 90 deg - Service 1539 -33 -140 -12039 449
Wind 180 deg - Service -20 1537 12086 54 203
Page
tnxTower
Job
ESTACION: CMED LA ESTRELLA LA INMACULADA 20 of 27
Project Date
TORRE CUADRADA DE 12 m SECCION 1.0x1.0m 06/12/23
Av Troncal de Occ No 18-76
Mosquera - Colombia Client Designed by
Phone: (601) 893 9874
FAX: (601) 893 9874 Ing Jaime Gutierrez
Load Combinations
Comb. Description
No.
1 Dead Only
2 1.2 Dead+1.0 Wind 0 deg - No Ice
3 0.9 Dead+1.0 Wind 0 deg - No Ice
4 1.2 Dead+1.0 Wind 45 deg - No Ice
5 0.9 Dead+1.0 Wind 45 deg - No Ice
6 1.2 Dead+1.0 Wind 90 deg - No Ice
7 0.9 Dead+1.0 Wind 90 deg - No Ice
8 1.2 Dead+1.0 Wind 180 deg - No Ice
9 0.9 Dead+1.0 Wind 180 deg - No Ice
10 Dead+Wind 0 deg - Service
11 Dead+Wind 45 deg - Service
12 Dead+Wind 90 deg - Service
13 Dead+Wind 180 deg - Service
Section Elevation Component Condition Gov. Axial Major Axis Minor Axis
No. m Type Load Moment Moment
Comb. kg kg-m kg-m
Max. Mx 6 1785 0 0
Max. My 6 -1222 0 0
Max. Vy 6 1 0 0
Max. Vx 6 0 0 0
Horizontal Max Tension 4 273 0 0
Max. Compression 4 -273 3 0
Max. Mx 8 195 4 1
Max. My 8 -60 0 -2
Max. Vy 8 9 4 1
Max. Vx 8 -3 0 -2
Top Girt Max Tension 8 463 0 0
Max. Compression 9 -390 0 0
Max. Mx 6 455 0 0
Max. My 6 36 0 0
Max. Vy 6 2 0 0
Max. Vx 6 0 0 0
Maximum Reactions
Location Condition Gov. Vertical Horizontal, X Horizontal, Z
Load kg kg kg
Comb.
Leg D Max. Vert 8 15705 282 -1064
Max. Hx 8 15705 282 -1064
Max. Hz 3 -14020 -264 1080
Min. Vert 5 -21353 -1135 945
Min. Hx 7 -14092 -1209 142
Min. Hz 8 15705 282 -1064
Leg C Max. Vert 8 15409 -514 -816
Max. Hx 3 -13092 501 773
Max. Hz 3 -13092 501 773
Min. Vert 3 -13092 501 773
Min. Hx 6 15275 -1212 -105
Min. Hz 8 15409 -514 -816
Leg B Max. Vert 4 22071 -863 1062
Max. Hx 9 -14150 527 -805
Max. Hz 4 22071 -863 1062
Min. Vert 9 -14150 527 -805
Min. Hx 4 22071 -863 1062
Min. Hz 9 -14150 527 -805
Leg A Max. Vert 2 14567 233 1067
Max. Hx 2 14567 233 1067
Max. Hz 2 14567 233 1067
Min. Vert 9 -13794 -268 -1042
Min. Hx 7 -13615 -647 -646
Min. Hz 9 -13794 -268 -1042
Solution Summary
Sum of Applied Forces Sum of Reactions
Load PX PY PZ PX PY PZ % Error
Comb. kg kg kg kg kg kg
1 0 -2833 0 0 2833 0 0.000%
2 59 -3399 -3729 -59 3399 3729 0.001%
3 59 -2549 -3729 -59 2549 3729 0.000%
4 2854 -3399 -2803 -2854 3399 2803 0.000%
5 2854 -2549 -2803 -2854 2549 2803 0.000%
6 3734 -3399 -72 -3734 3399 72 0.001%
7 3734 -2549 -72 -3734 2549 72 0.000%
8 -27 -3399 3715 27 3399 -3715 0.001%
9 -27 -2549 3715 27 2549 -3715 0.000%
10 16 -2833 -1548 -16 2833 1548 0.000%
11 1174 -2833 -1164 -1174 2833 1164 0.000%
12 1539 -2833 -33 -1539 2833 33 0.000%
13 -20 -2833 1537 20 2833 -1537 0.000%
Compression Checks
1
Pu / φPn controls
1
Pu / φPn controls
1
Pu / φPn controls
1
Pu / φPn controls
Tension Checks
1
Pu / φPn controls
1
Pu / φPn controls
1
Pu / φPn controls
1
Pu / φPn controls
Program Version 8.1.1.0 - 4/6/2021 File:D:/JG Ingenieria/Ingemec Asociados/WOM Torres/14 CMED La Estrella La Inmaculada TTA 12 m/tnx Tower CMED
La Estrella La Inmaculada/tnx tower TTA 12 m CMED La Estrella La Inmaculada.eri
Bogotá D.C., marzo 22 de 2023
Señores
Secretaria de Planeación Municipal
Palmito (Sucre)
La estructura metálica se encuentra dentro de las excepciones del NSR 10, (El diseño y
construcción de estructuras especiales tales como puentes, torres de transmisión, torres y
equipos industriales, muelles, estructuras hidráulicas y todas aquellas estructuras cuyo
comportamiento dinámico difiera de edificaciones convencionales no estén cubiertas dentro
de las limitaciones de cada uno de los materiales estructurales prescritos dentro de este
reglamento).
Cordialmente,
EL DIRECTOR GENERAL
CERTIFICA:
2. Que el(la) MATRICULA PROFESIONAL es la autorización que expide el Estado para que el titular
ejerza su profesión en todo el territorio de la República de Colombia, de conformidad con lo
dispuesto en la Ley 842 de 2003.
5. Que la presente certificación se expide en Bogotá, D.C., a los nueve (09) días del mes de Junio
del año dos mil veintitres (2023).
(*)Con el fin de verificar que el titular autoriza su participación en procesos estatales de selección de contratistas. La falta de firma del titular
no invalida el Certificado
El presente es un documento público expedido electrónicamente con firma digital que garantiza su plena validez jurídica y probatoria según lo
establecido en la Ley 527 de 1999. Para verificar la firma digital, consulte las propiedades del documento original en formato .pdf.
Para verificar la integridad e inalterabilidad del presente documento consulte en el sitio web
https://tramites.copnia.gov.co/Copnia_Microsite/CertificateOfGoodStanding/CertificateOfGoodStandingStart indicado el número del certificado
que se encuentra en la esquina superior derecha de este documento.