@ GPS positioning
@ Intelligent Hovering
@ Intelligent Following GPS X=
« Headless Mode
High-precision Adjustable
Steering Gear
@ Super Long Flying Time
6-Axis Gyro System 2.4GHz 5Channel 360°Flips
Please read the Instruction Manual carefully before using.
Please keep it for your further reference.p gf
Ye Blade A x2
Quadcopter X1 Transmitter X1 Blade B X2 Holder X1
2 MN =o
AC Adaptor X1 Protection Frame X4 —_— screwdriver X1_ Phone Holder Screw X2
iT Instruction
Protection Frame Screw X14 Manual X1
2.TRANSMITTER
2.1 Introduction of Transmitter
Power switch
Speed Switch
Ascend / Descend /
Turn Left / Turn Right
Press down to
start headless mode
Camera Steering
‘Angle "+
One Key Take Off/
Landing/ Emergency Stop
One Key Return
Indicator 1
Indicator 2
Forward/Backward
1 Left/Right sideward fly
Short press take photo/
1 Long press take video
One Key Follow
One key around Camera Angle "-"
(2M executable)
2.2 Install Batteries
@
One key waypoint flight
(Need fo be execute after set the APP)
L
Open the battery compartment Put in 4 AA batteries with Cover the battery compartment
by loosening the screw on the _ correct directions. and get it fastened with screw.
cover with a screw driver.a3 0
1. Flight Environment
5) (3) @
Indoor: Spacious spaces away from bariers, crowds or pet
are preferred.
Outdoor: Sunny, windless and breezy weathers are preferred.
Please keep the drone in sight during the flight and keep it
away from barriers, high-tension cables, trees and people.
(=)
Do not fly in extreme environment, such as hotness,
coldness, strong wind or heavy rain.
eoINSTALLATION PARTS
4.1 Installation of Smartphone Holder
Install Smartphone holder Disassemble Smartphone holder
xHold smartphone holder and push it along the sliding chute, which at the back
of controller. Smartphone holder is fastened properly when you hear a click,
then please lock it with the phone holder screw.
When you need to disassemble the
smartphone holder, please undid the
locked screw first. Then keep pressing
down the button at the middle of
sliding chute and pull it out.
To adjust your smartphone, please
adjust these three positions of the
smartphone holder as shown.
4.2 Install and Disassemble Protection Frame
All the protection frames could be install or
disassemble as consumer's needs.
xTake out all the protection frames and the
screws from parts bag. Hold protection
frame and press the screw positions down
into the screws holes in motor seat, then
lock the screws.
When you need to disassemble the protection frame, please undid the locked
screws and pull it out from motor seat.CHARGING OF THE QUADCOPTER BATTERY
Please fully charged the quadcopter battery before flying. Open the battery
door and take out the battery from quadcopter. Plug the AC adaptor into
electricity supply and its indicator will light on as green. Then connect the
output end to battery's input end, if adaptorVs indicator lights on as RED
means battery is charging, if indicator lights on as GREEN means battery is.
fully charged. Charging time is about 150-180 mins. Flying time is about 20
mins.
*kPlease keep the battery with 50% power for extending the operating life of
the battery if do no use the product for a long time.
4+-kHalf of the battery fully charge time could keep the battery with 50% power.
6. OPERATION GUIDE
6.1 Start Steps
@ Open the battery cover of quadcopter,
connect battery with quadcopter, close
battery cover.
@ Longtime press power switch with two.
seconds, the four LED indicators under
quadcopter's motor will flash, close the
battery cover. Then place the quadcopter
on the ground plane.
@ Turn on controller with two beeps, indicator 1
flash as green, push the left lever completely
forward and the controller will beep one time,
then pull it back completely and controller beep
again. Both the indicator 1 of controller and four
LED indicators of quadcopter will keep light on.
Now quadcopter and controller are paired.
@ After paired quadcopter and controller, place the
quadcopter on the ground plane, then rotate one
circle the control lever of Direction clockwise. Four LED lights of quadcopter
shall be flashing, and the gyro is calibrated and scanned for locking the location
QuadcopterCCs LED indicators keep light on and stop flashing means
calibration is finished.
°o7.WIFI REAL-TIME TRANSMISSI
7.1 Download APP
ay 7 mM = ita
Foreign Android ios QR Code Domestic Android
QR Code QR Code
7.2 Menu Screen
@After signal matching with controller, the
Wi-Fi indicator lights on and could be saw form
the gap at bottom of quadcopter.
@Go to the setting button in your smartphone,
open Wi-Fi, lock into the = “HK-GPS-XXXXX" .
@Click to link till you see “Linked” , means
pairing.
@Open the downloaded APP “HKGPS" , click
the icon enter control menu and smartphone
with real-time imager.
lf fail to connect Wi-Fi, it will be “Linking” ,
please re-connect Wi-Fi. A: Go to settings B: Open Wi-Fi
C: Connect "HK-GPS-XXXXX"
.
t—<) The aircraft has calibrated the magnetosphere in
this area "Yes" No point "No"
A: Open "HKGPS" APP Point "yes" APP directly into the main interface
B: Click the "ENTER" button Point "No" to enter the calibration page
eoGeomagnetic calibration
At this point two LED lights behind the aircraft
flash, the aircraft into the geomagnetic
calibration, the aircraft picked up was a
horizontal clockwise or counterclockwise
rotation, until the aircraft left at the bottom of
the LED is always lit so far. Then the aircraft
erected, clockwise or counterclockwise
rotation, until the aircraft at the bottom right bed . —————
corner of the LED is always bright so far. At ‘ WTS &
this time, the aircraft LED lights constantly t
indicating that the calibration is successful.
The first time the aircraft must fly in this place, it is necessary to proceed with
the geomagnetic calibration. If the APP interface is "YES", please clear the phone
background to re-enter the APP and then calibrate.
xf the aircraft during the flight crash or collision hovering instability, the aircraft
will be placed in a plane, the APP interface, click "@®" aircraft for gyro calibration,
the four LED lights flashing began to become permanent Indicates that the aircraft
calibration was successful.
Geomagnetic calibration is successful, enter the user interface
=a PED Baad
IVT euc tc Se SNL 7
MANyeroinseae titers Nc
Gyro calibration (horizontal) ars
Return (show) Photo @
Surrounding flight (show) Video va
Follow (show) Ios i}
Right after the success of the frequency and wifi connection, the lower right
corner of the LED lights slowly flashing (the aircraft search for GPS signals, the
first search GPS signal is slow, please be patient) the lower right corner of the
LED lights lit normally said the aircraft can take off;
*&When the aircraft all LED lights, please wait for a moment,
the upper right corner of the APP "GPS parameters" is
recommended less than 100cm, so hover, return better.
Press the remote control "a key off* button at the lower left corner, the remote
control issued a "beep" a sound, the aircraft automatically take off set high and
fixed-point hovering in this position.
Or the left and right joysticks at the same time hit the lower corner, and release,
the aircraft propeller low-speed rotation, and then push the throttle, the aircraft
rose to a certain height, and release the throttle, this time the aircraft set high
and fixed hovering in this position.
6)#xif the aircraft can not receive the GPS signal in the indoor or basement, the
LED light slowly flashes in the lower right corner of the aircraft, At this time, the
aircraft can only be used to start the aircraft to perform ordinary fixed high mode
with the “inner horoscope" of the joystick (one-key take-off, return, surround,
follow, etc Function is invalid)
7.3 Stop Fly Step
The throttle hit the lowest position, the aircraft automatically landed to the ground,
the blade stops turning.Or press the left control button on the lower right button,
the remote control emits a "beep" sound, the aircraft automatically landed to the
ground, the blade stops Turn.
Emergency stop
In case of emergency, press "One-touch take-off" button continuously, the
remote control emits "beep" x2 sound Urgently stop the aircraft or operate the
remote control leftward and rightward at the same time Beat emergency stop
All emergency stop function aircraft less than 2 M side can be implemented
above 2 M automatic landing mode8. OPERATION AND CONTROL GUIDE
8.1 Speed Shift
During playing, use the button at top left corner for speed shfit according to
player's need.
Short press for speed switch, per short press increase one speed.
@ Low speed: Press the speed shift button
with a beep, quadcopter fly as 30% speed.
@ Medium speed: Press the speed shift
button with two beeps, quadcopter fly as
60% speed.
@ Fast speed: Press the speed shift button
with three beeps, quadcopter fly as 100%
speed.
6.2 Basic Motion Operations
Push the left lever
{acceleratorjup and
down, the quadcopter
will ascend and
descend accordingly.
Descend
Turn Left
Push the left lever
(acceleraton)leftward
and rightward, the
quadcopter will turn
left and turn right
accordingly.
Push the right lever
(direction), up and
down.the quadcopter
will go forward and
backward accordingly.
BackwardPush the right lever
(direction),leftward
and rightward. the
quadcopter will go
left sideward and right
sideward
accordingly.
In normal GPS flight, when you press the
remote control "one key return" button, the
remote control issued a "beep" sound, the
aircraft nose turned to the takeoff direction,
began to automatically return to the take-off
location; return to manipulate the remote
control right Rod rod aircraft to lift the return,
or press "a key return" aircraft to lift the
return.
1. The aircraft automatically returns when it enters low voltage
2. The aircraft automatically returns when the signal is lost
3. Remote power off automatically returnONE KEY AROUND
During the flight, fly the aircraft to the position where you want to perform the
surround. Press the "One-key Surround" button on the remote control to make
the remote control emit a "beep". After the aircraft has flown to the set radius
with this position as the center, the aircraft After the nose is turned around the
center, a 360 ° orbital flight is performed
Surround the remote control to manipulate the right rocker to hit the pole
aircraft to lift around
ONE KEY FOLLOW
This function must be connected to the APP push APP can be operated normally.
Press the "One key follow" button on the remote control to follow the GPS
coordinates of the mobile phone.
Follow the manipulation of the remote control right stick joystick to lift the
aircraft to follow
4kFollow the process, the phone no electricity or calls, the aircraft stopped
following, hovering on standby.
E KEY WAYPOINT FLIG
In order to use this function, the APP must update the map automatically after
opening the APP with the traffic or WIFI. (If you do not update the map, the map
will not be displayed on the APP, and the map must be upgraded automatically.)
Set the desired waypoint in the APP A waypoint can be set flight height, hover
time, flight speed. Can set up 5 destinations) Click Upload
@®ne
Radio Multiple
°
@OCCe
+
N\
After setting, press the remote control "a key waypoint flight" button, the aircraft
automatically fly to set the first waypoint, the second ...... After the completion of
the aircraft hovering at the last waypoint standby, waypoint After the flight is
over, please click delete the set waypoint, follow-up before reset.
Waypoint manipulation remote control right rocker hit rod aircraft to lift
waypoint flight
HEADLESS M
3
Headless Mode Shift
xStart/Setting: Upon pairing the controller with the quadcopter, place the
quadcopter staying on the ground or hovering in the air, ensure the head of
the quadcopter (Camera is in the front side) in the same direction with the
head of the controller. Press down the left rod into the headless mode, with a
beep, quadcopter's across corner LED indicators are flashing.
Quit: Press down the left rod again to quit the headless mode, with a beep,
quadcopter’s four LED indicators are on.
Orienting 4p
A BPOperation Turning
See the diagram. In Headless Mode, with diagonal indicators flashing, no matter
which direction the head (same side as camera) faces to, pull down the right rod
and quadcopter will fly back; on the contrary, push forth, it will fly away from
player.9.2 Personalized settings
Click APP a to make various settings and click to set the range.
ROR CR uN cae tel (o-somB id
Mtns (om ___——_—~ds
Meta Mes (-1om6 |
emus cules Go-smfo
POR UCn ns (-sMB_
OM RUN Need (10-30Mif
Maes (Co) |
tet Te
ome cued
oR UCR nS
aT see ee Runa Recs
Allows manual calibration of map
coordinates
eee Cronus
(used in mainland China)
Disable Guide mode
IVE
Flight waypoint sampling
Eee9.3 APP support 3D VR
Consumer could purchase related VR product for 3D flight. When click the
icon in the upper right corner, control interface change to two parts. The VR's
ware, focal length adjustment and other settings, please check the user manual
of the VR.
9.4 High Precision Adjustable Steering Gear
The camera system of quadcopter built with HD camera and high precision
adjustable steering gear, and it could be adjusted the shooting angle by the
buttons on controller.
@Short press the upper button, camera will move up. When long press this
button, camera will keep moving up.
@When press the lower button, camera will move down. Camera could be
moved over 90°,
To move the camera for keep video smooth and beauty.
@9.5 Take Photo & Video
During flying time, taking photo and video by APP. Click the icons on smart photo
or press the button on controller.
ro 6
3) Om aa
@ Press the left button to take a picture, per press camera take a picture.
@ Press the right button to start taking video then press again to stop and save
the video.
9.6 View Saved Documents @
@Finished taking picture or video, it could be viewed in the APP.
@The document also saved in SD card of camera. To check document by
computer, please turn off the power of quadcopter, press SD card and take it
out first. Then take out the SD card reader from the parts bag, install the SD
card, connect card reader to USB port of computer.
%** When quadcopter fly out of Wi-Fi effective control range, picture or video
are saved just in SD card not in APP. Once picture or video could not be find in
APP, not means it was lost or not be saved.
10.FLIGHT ENVIRONMENT
= == ea Do not operate the
Se quadcopter in the bad
a FC ® conditions as
mentioned
E\S for advoiding accident
or unexpected
demages.
11. INSTALL BLADES
The blades shall be installed to designated location.
To install or change quadcopter’s blade, check the letter on blade and make
‘sure it is same as the letter on motor seat. Blade A should be install to the motor
seat with letter A, and so blade B is install to motor seat with letter B. Or
quadcopter could not fly in normal
®&Both blade shaft and blade install hole with lock
Position to make sure the blade should be install
at correct position.
@ Take apart of the blade locker screw and the
lower lampshade locker screw, then take out the
damaged blade.
@Take out the new blade and aim it at the blade
shaft till it hit the gear then turn it right or left till
the inside locker position tight with the blade
shaft.
@Continue push blade till the end then lock the
blade screw and lower lampshade screw.
12.SAFETY PRECAUTIONS
@ Stay away from obstacles
This product is workable outdoors Selecting barrier-free environment to
advoiding demage due to impact person or things.
@ Leave away from moisture or heat source
The interior of an aircraft is made up of a number of sophisticated electronic
components, so it must be protected from moisture or moisture as well as
high temperature storms. Drying and so on.
@Lithium battery safety
Itis strictly prohibited to use the lithium battery outside the factory to fly, the
internal configuration of the lithium battery used by different manufacturers is
Very different, so as not to cause damage to the aircraft electronic components
and personal safety and other dangerous.
It is strictly prohibited to use the battery charger outside of the factory for
charging, so as to avoid short circuit, expansion, deformation, or even fire,
explosion and other dangerous.
@NiMH battery safety
Please notice the place of anode and cathode when pit in the batteries into
controller. In order to protect the life of batteries, do not mix the new and old
battery.
When quadcopter is not used for long periods of time, please take out all
batteries to avoid battery leakage, battery failure. Please do not use leaky
battery.
@&13.TROUBLE SHOOTING
Problem Reason Solution
‘a. Stagal ranching “led. 1. Re-matching again.
The quadcopter | 7 Qusdeopteror 2: Replace the transmitter
didnot respond | * Rensmiter ow voltage batteries
3. Re-charge to quadcopter
1. Checking the instruction manual of
1. The blade is assembled installing blades
Unable to 2 Pik deforma 2. Righting blades or replacement blades
take off Sond: impact co oe 3. The low-voltage protection, re-charge
. Quadcopter LED flashes to quadeopter
The quadeopter 1. Blade impact deformation _| 1. Righting blades or replacing blades.
2. gyroscope deviation 2. Read the calibration part and do again.
The quadcopter
response delay Transmitter low voltage Replacing the battery of transmitter
or interrupt signal
1. Geomagnetism is not 1. Follow the instructions to calibrate the
The quadcopter calibrated geomagnetism
can not hover 2. The gyroscope is not 2. Follow the instructions to calibrate the
calibrated gyroscope
1. The first boot please be patient GPS
search signal
Lower right comer 2.Do not place in another place suchas
er ie No GPS signal was found electric tower, high-voltage electric
LED flash slowly interference big position.
3. Do not indoors, basement, a few no
GPS signal location
7
LeD Tht flash Perform GYRO calibration | Place the aircraft on a flat surface
The two LED light:
flash after the ayeraft | Geomagnetic calibration See page 6 for geomagnetic calibration
14.SPARE PART:
S
1.Transmitter 2.Phone holder 3.A/C adaptor
@a
4.Camera sets 5.Li-ion battery
> ==
. a
7.Lower body 8.Stands + Antenna
Cover
9.Blade
|
11.Positive inversion
motor
10.Protection frame
12.Motor seat
>
ot)
S 8
13.Motor cover
14.Lampshade
Gj
15.Long/short carbon
fiber tube
@®forward’? backward light 17 Geerwith shaft ES ght
o 9°
7 +51
e 9
°° 9
19.Bearing 20.Battery seat 21.Battery door/front
lampshade
i 23.Steering engine
eeheccivel boatd with Wi-Fi Creuit board
¢——. —
24.GPS module 25.Pressure module
&
EX Bre RZ =
CE AY DIL\SY
--- Thank you for buying this product, | wish you have a good timel - - -
@