Documentos de Académico
Documentos de Profesional
Documentos de Cultura
COMANDERA MA5600T......................................................................................0
REALIZAR UN BACKUP......................................................................................1
BORRADO DE LA FLASH....................................................................................5
ASIGNAR/CAMBIAR IP DEL EQUIPO (FUERA DE BANDA)...............................6
CONFIGURAR SNMP..........................................................................................9
RESTAURAR LA CONFIGURACION DESDE UN BACKUP..............................10
GUARDAR EN MEMORIA FLASH.....................................................................13
CONSULTAR CONFIGURACIÓN EXISTENTE DE UNA ONT...........................14
ALTA ONT.......................................................................................................... 16
BORRAR UNA ONT...........................................................................................17
REVISAR ONT CLIENTE...................................................................................19
DIAGNOSTICAR TRANSPORTE.......................................................................20
APAGAR UN PUERTO PON..............................................................................23
DESPLEGADOS.................................................................................................24
MODIFICAR........................................................................................................30
1-1
REALIZAR UN BACKUP
BORRADO DE LA FLASH
Borramos los datos de la flash
MAQCHI(config)#erase flash data active
This command will clear the active board data that has been loaded or saved
Command executes successfully, and will take effect after active board
rebooted
Reiniciamos el sistema
MAQCHI(config)#reboot active
Please check whether data has saved, the unsaved data may lose if reboot
active board, are you sure to reboot active board? (y/n)[n]:y
Standby board failure or not exist, reboot active will cause system reboot,
are you sure to reboot active board? (y/n)[n]:y
MAQCHI#save
MA5600T>idle-timeout 200
1-6
Entramos a la interfaz:
MA5600T(config)#interface meth 0
Desbloqueamos:
MA5600(config-if-meth0)#undo shutdown
Info: Interface meth0 is not shutdown
La visualizamos:
MA5600(config)#display ip interface meth 0
Command:
ip route-static 0.0.0.0 0.0.0.0 13.73.26.254
1-9
CONFIGURAR SNMP
Configuramos SNMP (Simple Network Management Protocol), este lo
utilize el servidor de gestión U2000 que utilizan el CSM y el CNS:
Command:
snmp-agent community write private
Command:
snmp-agent community read public
Command:
snmp-agent target-host trap-paramsname private v1 securityname privat
MA5600T(config)#
MA5600T(config)#
Note: the new file in 0 frame 9 slot will take effect after system is
restarted
MA5600T(config)#
The loading is successful
PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Load type: Host data, Load
Object: Active control board
MA5600T(config)#
1-11
***Pide dar reboot al equipo:
MA5600T(config)#reboot system
Please check whether data has saved, the unsaved data will lose if reboot
system, are you sure to reboot system? (y/n)[n]:y
MA5600T(config)#
===============================================================
BOARD INFORMATION :
CPU: MPC8548. Processor #1.(Rev 2.02) running at 1333Mhz
512M bytes DDR(ECC), 128M bytes flash installed on board
Baudrate of serial channel is 9600bps
Board's LAN IP address is 13.73.26.130
Board's LAN Subnet mask is 255.255.255.0
Board's LAN MAC address is 64:3E:8C:A9:DF:4B
===============================================================
Iniciamos sesión
>>User name:root
>>User password:
User root has used a default password. Change the password in time.
MA5600T>idle-timeout 200
1-13
MA5600(config)#save
1-14
Los valores de RX y TX es necesario anotarlos para poder dar de alta otra ONT.
VLAN ID equivale al valor de VLAN HSI (para alta)
RX equivale al valor de inbound traffic-table index (para alta)
TX equivale al valor de outbound traffic-table index (para alta)
1-16
ALTA ONT
Primero hay que ingresar al slot donde esta conectada la ONT que
vamos a dar de alta:
MA5600T(config)#interface gpon 0/12
12 = SLOT
DIAGNOSTICAR TRANSPORTE
Borramos el service port (cross-connection) utilizando el INDEX.
MA5600T(config)#interface giu 0/19
Estos comandos aplican también para revisar los puertos del SLOT 9, en
este caso solo cambia el primer comando por: interface scu 0/9.
1-21
Revisamos que las potencias opticas esten en rango de acuerdo al
modulo instalado.
MA5600T((config-if-giu-0/19))#display port ddm-info 0
1-22
AGREGAR UN NUEVO USUARIO DE GESTIÓN LOCAL
MA5600T(config)#terminal user name
User Name(length<6,15>):telmex
User Password(length<6,15>):telmex01
Confirm Password(length<6,15>):telmex01
User profile name(<=15 chars):[root]:dar enter
User's Level:
1. Common User 2. Operator 3. Administrator:3
Permitted Reenter Number(0--4):3
User's Appended Info(<=30 chars):0755-28977021
Adding usdr successfully
Repeat this operation? (y/n)[n]:n
DESPLEGADOS
Tabla de trafico (fuera de uso, anteriormente perfiles)
MA5600(config)#display traffic table ip from-index 0
MODIFICAR
Modificar el tiempo de la sesión de gestión:
MA5600T#idle-timeout 200