Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Como Configurar Un COM-818 Steren
Como Configurar Un COM-818 Steren
WI-FI de pared
COM-818
Gracias por la compra de este producto Steren.
Este manual contiene todas las indicaciones necesarias para manejar su
nuevo Repetidor y punto de acceso WI-FI de pared.
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que
este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe
aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”
2
IMPORTANTE
CARACTERÍSTICAS
• El repetidor y punto de acceso portátil le ayudará a ampliar la cobertura
de la red inalámbrica de su hogar o pequeña oficina, además de que puede
utilizarlo como punto de acceso y generar una red inalámbrica en el lugar
donde se coloque.
3
CONTROLES
5 6 7 8 9
1. Botón de sistema de
protección de red inalámbrica
2. Entrada red LAN
LAN WAN WPS WLAN POWER
1
LEDs indicadores 4
5. Red LAN activada WPS
WAN
LAN
LAN
2 3
4
MODO DE USO
MODEM
LINEA
Para una configuración inalámbrica típica en el hogar (como se muestra arriba), haga lo
siguiente:
• Usted necesita acceso a Internet de banda ancha (a ADSL, línea de módem por cable en
su casa u oficina).
• Consulte a su proveedor de ADSL o cable módem para una correcta instalación del
módem.
• Conecte el ADSL o cable módem al ruteador COM-818 en la entrada LAN y conecte el
ruteador en la toma de corriente eléctrica.
Si el equipo solicita un código PIN o “set up” de la red, haga clic en “Conectar sin
configurar”.
6
3. Abra el navegador web y escriba http://192.168.10.253 en el cuadro de dirección del
navegador. Este número es la dirección IP por defecto para este dispositivo.
7
Agregar inalámbricamente computadoras al Ruteador
con el botón WPS
8
Cómo configurar la dirección IP en su computadora o
laptop
1. Inicie la computadora.
2. Dé clic en Inicio > Panel de Control > Centro de redes y recursos compartidos elija
Conexión de área local. Seleccione Propiedades y en esa ventana elija Protocolo de
Internet versión 4 (TCP/IPv4), después dé clic en Propiedades.
3. Ajustar dirección IP manualmente: Ingrese 192.168.10.x (x es del 2 al 252), y para la
máscara de subred 255.255.255.0. Ingrese la dirección IP de LAN del ruteador (el valor
por defecto es 192.168.10.253) en el campo Puerta de enlace.
9
ASISTENTE
Ruteador. Modo estándar del Ruteador inalámbrico: Este ruteador se conecta a internet
mediante un puerto WAN, por lo que otros dispositivos pueden conectarse al ruteador
inalámbricamente o conectarse al puerto LAN del ruteador por medio de un cable.
AP. Ruteador tradicional con cable y función inalámbrica: Este ruteador puede
conectarse al puerto LAN del ruteador de enlace ascendente con un cable; la terminal
del usuario puede conectarse al ruteador inalámbricamente.
Repetidor. Extiende ampliamente la señal inalámbrica: Este ruteador se puede
conectar ascendentemente al ruteador inalámbricamente; el usuario terminal puede
conectarse al ruteador mediante un cable o inalámbricamente.
ISP inálambrico. Ruteador inalámbrico que se utiliza como puerto WAN: Este ruteador
se puede conectar inalámbricamente al enlace ascendente y al mismo tiempo puede
extender inalámbricamente la señal a otros dispositivos conectados.
10
Modo ruteador
11
Modo AP
12
Modo Repetidor
13
ISP inálambrico
14
CONFIGURACIÓN INALÁMBRICA
BÁSICA
15
AJUSTES LAN
Dé clic en Ajustes LAN. Se abrirá la siguiente pantalla:
- Si usted cambia la dirección IP de la red LAN, deberá iniciar sesión del ruteador con
la nueva dirección IP.
- Si la nueva dirección IP de la red LAN que usted establezca no se encuentra en la misma
subred, el conjunto de direcciones IP del servidor DHCP cambiará en consecuencia al
mismo tiempo, mientras que el Servidor Virtual y el Host DMZ no surtirán efecto hasta que
se hayan reconfigurado.
16
AJUSTES BÁSICOS WAN
- Dé clic en Ajustes básicos WAN. Se abrirá la siguiente pantalla:
17
Si su proveedor de Internet le proporciona
una dirección IP estática o fija, Máscara de
subred, Puerta de enlace y configuración de
DNS, seleccione IP estática.
Introduzca la Dirección IP / Máscara de
subred / Puerta de enlace predeterminada /
Tamaño MTU / DNS primario y secundario en
notación decimal con puntos proporcionada
por su proveedor de Internet.
ADMINISTRACIÓN
Cambiar la contraseña del administrador
La contraseña predeterminada del COM-818 es “admin” y se muestra en el indicador de
entrada cuando se accede desde el navegador web. Usted deberá cambiar la contraseña
para evitar riesgos de seguridad, esto es muy importante cuando tenga la función inalámbrica
habilitada.
Para cambiar la contraseña, siga estas instrucciones: Dé clic en Administración, aparecerá
la siguiente pantalla:
19
Zona horaria
20
Actualización del Firmware
El software del sistema usado por este ruteador es conocido como firmware, y como con
otras aplicaciones del sistema, cuando usted remplaza la aplicación vieja por una nueva, su
computadora tendrá nuevas funciones. También puede usar la función de actualización de
este firmware para añadir funciones a su ruteador, e incluso arreglar los errores.
Dé clic en Actualización de firmware. El siguiente mensaje aparecerá en su pantalla.
Jamás cierre el navegador web o desconecte su computadora del ruteador mientras está actualizando
el firmware. Si el firmware que ha cargado se corrompe, la actualización fallará y tendrá que regresarlo al
proveedor y pedir ayuda. (La garantía se anulará si usted interrumpe el proceso de actualización).
21
Para configurar su ruteador de manera más específica dé clic en el botón
Avanzar. La siguiente pantalla se abrirá:
22
RED
Ajustes avanzados
IP estática
23
Tabla de clientes DHCP
Esta pantalla muestra la dirección IP de los equipos actualmente conectados.
INALÁMBRICO
Ajustes básicos
24
- SSID: Identificador de servicios principal. Nombre de la red inalámbrica.
- Emitir SSID: Seleccione “Habilitar” para permitir que el dispositivo SSID sea accesible para
los clientes inalámbricos.
- Canal: Este campo determina qué frecuencia de operación se usará. El canal por defecto
es Auto, por lo que el AP elegirá el mejor canal automáticamente. No es necesario cambiar
el canal inalámbrico a menos que haya interferencia con otro punto de acceso cercano.
Seguridad inalámbrica
Configure la seguridad inalámbrica y la encriptación para prevenir el acceso no autorizado
y el monitoreo.
25
Ajustes inalámbricos avanzados
Estos ajustes son sólo para usuarios más avanzados técnicamente, quienes tienen un
conocimiento suficiente acerca del LAN inalámbrico. Estos ajustes no deben ser cambiados
hasta que usted conozca qué efecto va tener el cambio en su AP.
Horario
27
Configuración WDS
Es una función que permite la interconexión inalámbrica entre ruteadores o puntos de
acceso. De esta manera podremos usar el ruteador como repetidor de otra señal o para
interconectar 2 redes.
28
FIREWALL
Filtro de puertos
Active la filtración de puerto, introduzca el Rango de puertos que desea controlar.
Haga clic en el botón “Aplicar”. Observará el Rango de puerto que aparece en la tabla de
filtro actual.
Filtro de IP
El filtrado de IP es un mecanismo que decide qué direcciones IP serán procesadas
normalmente y cuáles serán descartadas.
29
Filtro de MAC
Consiste en que sólo se conecten a la red del ruteador las direcciones MAC que usted
quiera.
Filtro de URL
Ayuda a proteger su organización contra las amenazas de la web y permite controlar,
supervisar y aplicar políticas de uso aceptable de la web.
30
Redirección de puertos
Configuración DMZ
DMZ abre todos los puertos de una computadora / dispositivo hacia Internet. Debe ser
utilizado únicamente para un propósito en especial, ya que no contará con seguridad en
esta situación.
31
AVANZADO
DNS dinámico
Calidad de servicio
- QoS se encarga de priorizar el ancho
de banda disponible en función de las
necesidades del usuario y basándose
en una serie de criterios que clasifican el
tráfico.
- Puede seleccionar la activación o
desactivación de los controles QoS y
puede elegir que el ruteador seleccione
la velocidad de subida de manera
automática o manualmente.
- Dirección IP: configure el rango de la
dirección IP restringida.
- Dirección MAC: configure el rango de la
dirección MAC restringida.
- Configure el valor mínimo de subida y
bajada en el ancho de banda.
32
ESTADO
Muestra la información del ruteador.
33
ESPECIFICACIONES
• Alimentación: 127 V~ 60 Hz. 3 W máx.
• Estándar: IEEE 802.11b/g/n; IEEE 802.3 y 802.3u
• Puerto RJ45: 2. 1 WAN 10/100 Mbps y LAN 10/100 Mbps con auto negociación
de datos.
• Velocidad máxima de transferencia de datos: 300 Mbps de forma inalámbrica
• Transmisión y recepción: MIMO 2T2R
• Configuración de protección inalámbrica (WPS): Sí
• Chipset empleados: RTL8196E Y RTL8192ER
• Frecuencia: 2,4 GHz con 11 subcanales
• Seguridad: 64/128/152- bits WEP y compilación con 128 bits WPA (TKIP/AES)
• Distancia aproximada de cobertura: 10 metros a la redonda
• Consumo en espera: 1,5 W/h
• Consumo nominal: 2,5 W/h
34
Producto: Repetidor y punto de acceso WI-FI de pared
Modelo: COM-818
Marca: Steren
PÓLIZA DE GARANTÍA
Esta póliza garantiza el producto por el término de un año en todas sus partes y mano de obra, contra
cualquier defecto de fabricación y funcionamiento, a partir de la fecha de entrega.
CONDICIONES
1.- Para hacer efectiva la garantía, presente esta póliza y el producto, en donde fue adquirido o en
Electrónica Steren S.A. de C.V.
2.- Electrónica Steren S.A de C.V. se compromete a reparar el producto en caso de estar defectuoso sin
ningún cargo al consumidor. Los gastos de transportación serán cubiertos por el proveedor.
3.- El tiempo de reparación en ningún caso será mayor a 30 días, contados a partir de la recepción del
producto en cualquiera de los sitios donde pueda hacerse efectiva la garantía.
4.- El lugar donde puede adquirir partes, componentes, consumibles y accesorios, así como hacer válida esta
garantía es en cualquiera de las direcciones mencionadas posteriormente.
This manual includes all the feature operations and troubleshooting necessary
to install and operate your new Steren´s WI-FI wall mount access point and
repeater.
www.steren.com
The instructions of this manual are for reference about the product. There may
be differences due to updates.
Please check our web site (www.steren.com) to obtain the latest version of the
instruction manual.
“The operation of this equipment is subject to the following two conditions: (1) it is possible that
this equipment or device may not cause harmful interference, and (2) this device or device must
accept any interference, including interference that may cause undesired operation .”
2
IMPORTANT
• Do not use or store this equipment in places where there are dripping or
splashing of water. It may cause electric shock or malfunction.
• Verify that the electricity in the place where you want to install the router
unit is stable.
• Unstable electricity can cause damage to the unit or cause serious damage.
HIGHLIGHTS
• The portable repeater and access point helps to extend wireless network
range at home or office, what is more, you can use it as an access point and
generate a wireless network in the place you want.
• Also, you can connect through the RJ45 cable a switch or computer, it
includes WAN and LAN ports to use with devices with no wireless card or to
set the device.
3
CONTROLS
5 6 7 8 9
button.
2. LAN network input.
3. WAN network input.
4. Reset button. 1
4
Led indicators WPS
WAN
LAN
LAN
2 3
4
HOW TO USE
MODEM
LINEA
For a typical wireless setup at home (as shown above), do the following:
• You’ll need broadband Internet access (ADSL, modem line cable in your home or office).
• Ask your ADSL or cable modem provider the proper installation of the modem.
• Connect the ADSL or cable modem to the COM-818 router on the LAN input and plug the
router into the electrical outlet.
5
Add computers to the COM-818
1. Log on to the computer (or start the computer).
3. In the list, select the “COM-818” wireless network and then click Connect.
4. If requested, enter the security password or network key, and then click OK.
A confirmation message will appear when you are connected to the network.
5. To confirm that you have added the computer, run the following:
Click on Start, Control Panel, then in the search box type “network”; then click on view
computers and network devices. You should see icons for the computer you added and
those of other computers and devices that are part of the network.
If you don’t see icons in the network folder, it is possible that for network discovery and
file sharing are turned off.
If your computer requests a network PIN code or “set up”, click on “Connect without
setting up”.
6
3. Open the web browser and type http://192.168.10.253 in the browser’s address box.
This number is the IP default address for the router.
7
Add wireless computers with WPS button
1. Connect the Router to an outlet. Connect your computer or laptop to the router via
RJ45 cable.
2. To verify that the computer is added, do the following:
Open Network by clicking Start > Control Panel; in the search box, type network, then,
under Network and Sharing center, click View network computers and devices. You
should see icons for the computer you added and for the other computers and
devices that are part of the network.
8
How to configure the IP address on your computer or
laptop
1. Start the computer.
2. Click Start > Control Panel > View network Status and Tasks > Manage Network;
then right-click on Local Area Network > Properties. When the Local Area Connection
Properties window appears, select “Internet Protocol Version 4 (TCP/IPv4)” and then
click Properties.
3. Set IP address manually: Enter 192.168.10.x (x is from 2 to 252), and the subnet mask
255.255.255.0. Enter the LAN IP address of the router (the default is 192.168.10.253)
in the Gateway field.
9
WIZARD
After you log in successfully, configure your
router on the Wizard quick menu.
Choose the operating mode you need, and
then click Next.
Router. Standard wireless router mode: This router connects to Internet by WAN port,
and then other terminal devices can connect to this router by wireless connection or
connect to this router’s LAN port with a cable.
AP. Traditional wired router realize wireless function: This router can connect to uplink
router’s LAN port by wired connection, user terminal can connect to this router by
wireless connection.
Repeater. Extend wireless signal comprehesively: This router can connect to uplink
wireless router by wireless connection, user terminal can connect to this router by wired
or wireless connection.
WISP. Wireless used as WAN port: This router can connect to uplink wireless router by
wireless connection, at the same time, it can extend wireless signal for other devices’
connection.
10
Router mode
Set the wireless parameter. It is recommended to change the name of the SSID, choose
Safe mode and enter a password (key).
If dynamic IP is selected, the router obtains the IP address automatically DHCP server
or ISP. You don’t need to configure it and you can continue with the wireless settings.
If you selected PPPoE, enter the user name and password provided by your ISP. These
fields support capital letters.
SSID: Network’s name
Channel: “Automatic” is recommended
Security mode: Configure wireless security and encryption to prevent unauthorized
access.
11
AP mode
- Set the wireless parameter. It is recommended that you change the name of the SSID,
choose Safe mode and enter a password (key).
SSID: Network’s name
Channel: “Automatic” is recommended
Security mode: Configure wireless security and encryption to prevent unauthorized
access.
- Click Save and reboot to reboot the router and finish the configuration.
12
Repeater mode
The SSID of the network destination will appear automatically, type the password and
then click on Save and reboot.
13
Wireless ISP
The SSID of the network destination will appear automatically; choose a password and
click Save and reboot.
14
WIRELESS BASIC SETTINGS
15
LAN BASIC SETTING
Click LAN Basic Setting. The following screen will appear:
- IP address: Enter the IP address of your router, the factory preset is: 192.168.10.253.
- Sub network: address code that determines the size of the network. Normally use
255.255.255.0 as the subnet mask.
- Type of DHCP server, client, or disabled.
- If you change the IP address of the LAN must log of the router with the new IP address.
- If the new IP address on the LAN that you set are not on the same subnet, the IP addresses
set from the DHCP server change accordingly at the same time, while Virtual Server and
DMZ Host will not take effect until they have been reconfigured.
16
WAN BASIC SETTING
Click WAN Basic Setting. The following screen will appear:
17
If your ISP gives you a static or fixed IP
address, subnet mask, gateway and DNS
settings, select static IP.
18
MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size
permitted for network transmission. Most DSL users should use the value 1492.You can set
the MTU manually, and you should leave this value in the 1200 to 1500 range. If the value
you set is not in accord with the value of your service provider, it may causes problems.
MANAGEMENT
Change the administrator password
COM-818 default password is “admin” and is displayed in the indicator when accessed
from the web browser. You should change the password to avoid security risks, this is very
important when you have the wireless function enabled.
To change the password, follow these instructions: give click Administration, the following
screen appears:
When you are finished, click “Apply”; if you want to keep the original password, click on
“Reset”.
19
Time zone
Save file settings: press “Save” and you will be asked to download the configuration as a file,
can save it with different names for different versions and keep it in a safe place.
Load file settings: press “Browse” to choose a configuration file previously saved on your
computer and then click on “Upload” to transfer the file of configuration to the router. Once
the configuration has been loaded, the configuration of the router will be replaced by that file.
Reset to defaults: click on “Reset to defaults” to remove all the settings made and restore
the router to the factory settings.
20
Firmware upgrade
The software of the system used by this router is known as firmware, and as with other
applications of the system, when you replace the old application with a new one, your
computer will have new features. You can also use this firmware update function to add
functionality to your router, and even fix the errors.
Click firmware update. The following message will appear on your screen.
Give click on select file, you will be asked the name of the firmware upgrade file. Please,
download the latest firmware from our website and use it in your router.
After choosing a firmware update file, give the router and click on “Update” will be updated
automatically. This can take several minutes, be patient.
Never close your web browser or disconnect your computer from the router while you are upgrading the
firmware. If the firmware was loaded is corrupt, the update will fail and will have to return it to the supplier
and ask for help. (The warranty is void if you interrupt the update process).
21
For more specific setup, click on “Advance”. The following screen appears:
22
NETWORK
Advance Setting
Static IP
23
DHCP Client Table
This displays the IP address for devices currently connected.
WIRELESS
Basic settings
24
- SSID: Main service identifier. The name of the wireless network.
- Broadcast SSID: Select “Enable” to enable that the device’s SSID is accessible to wireless
clients.
- Channel number: this field determines which operating frequency will be used. The channel
by default is Auto, so the AP will choose the best channel automatically. It is not necessary
to change the wireless channel unless there is interference with other nearby access point.
Wireless Security
Configure wireless security and encryption to prevent unauthorized access and monitoring.
25
Wireless Advanced Settings
These settings are only for more technically advanced users who have sufficient knowledge
about wireless LAN. These settings should not be changed until you know what effect the
change will hace on your AP.
26
Access Control
Setup the wireless access control based on the MAC address.
The access control has 3 options: Disable, Allow listed and Deny listed.
Schedule
27
WDS settings
Allows wireless interconnection between routers or access points. This way we can use the
router as a repeater of another signal or to interconnect 2 networks.
28
FIREWALL
Port Filtering
Enable port filtering, enter the Port range you want to control.
Click on “Apply”. The port range will appear in the current filter table.
IP filtering
The IP filtering decides which IP addresses will be normally processed and wich are
discarded.
Enable the IP filtering, enter
the IP address you want to
control.
Click on “Apply”. You will
notice the IP addresses
configured on the current
filter table.
29
MAC Filtering
With this you can control the MAC addresses you want to connect to the router’s network.
URL Filtering
It helps protect your organization against web threats and to control, monitor and enforce
acceptable use policies of the web.
30
Port Forwarding
DMZ
It opens all the ports of a computer/device to the Internet. It should be only used for a special
purpose, because there will not be security able in this situation.
31
ADVANCED
Dynamic DNS
Quality of Service
- QoS prioritize available bandwith
according to the user requirements and
based on a number of criteria which
classify traffic.
- You can enable or disable the QoS
controls and you can select if the router
upload speed will be automatically or
manually.
- IP Address: configure the IP address
range of the restricted IP.
- MAC Address: configure the range of the
restricted MAC address.
- Set the minimum value of uplink and
downlink bandwidth.
32
STATUS
Displays the router’s status.
33
• Input: 127 V~ 60 Hz. 3 W max.
• Standard: IEEE 802.11b/g/n; IEEE 802.3 and 802.3u
• RJ45 port: 2. 1 WAN 10/100 Mbps and LAN 10/100 Mbps with data
auto-negotiation
• Maximum data transfer speed: 300 Mbps wirelessly
• Transmission and reception: MIMO 2T2R
• Wireless protection setting (WPS): Yes
• Chipset: RTL8196E and RTL88192ER
• Frequency: 2.4 GHz with 11 sub-channels
• Security: 64/128/152- bits WEP and compilation with 128 bits WPA (TKIP/AES)
• Approximate coverage range: 10 metres around
• Stand-by power consumption: 1.5 W/h
• Nominal consumption: 2.5 W/h
34
Product: WI-FI wall mount access point and repeater
Part number: COM-818
Brand: Steren
WARRANTY
This Steren product is warranted under normal usage against defects in workmanship
and materials to the original purchaser for one year from the date of purchase.
CONDITIONS
1. This warranty card with all the required information, invoice, product box or
package, and product, must be presented when warranty service is required.
2. If the product is in the warranty time, the company will repair it free of charge.
3. The repairing time will not exceed 30 natural days, from the day the claim was
received.
4. Steren sell parts, components, consumables and accessories to customer, as well
as warranty service, at any of the addresses mentioned later.
If the product has been damaged by an accident, acts of God, mishandling, leaky
batteries, failure to follow enclosed instructions, improper repair by unauthorized
personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase
ticket.
RETAILER INFORMATION
Name of the retailer In case your product fails
Address or have questions, please
Product contact your nearest dealer.
Brand If you are in Mexico, please
Part number call to our Call Center.
Serial number 01 800 500 9000
Date of delivery
35