Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Leyenda:
pags. - lazo
ch - bucle de aire
sc - crochet sencillo
10-11. 48 pb (48)
14-15. 36pbs (42)
18-19. 36 pb (36)
22-23. 30 pb (30)
26-27. 24 pb (24)
30-31. 18pb (18)
34-35. 12pb (12)
Ponemos más relleno, luego tejemos la parte superior, no ponemos el relleno en la parte superior.
38-41. 9pb (9)
42. (1mp, dic) * 3 (6)
43-50. 6pbs (6)
(SL-ST, 3 canales, 2DC, 3 canales, SL-ST): en un bucle, omita un bucle. Entonces tejemos hasta el final de la fila.
Coser encaje de algodón entre las dos últimas filas (ancho de encaje 2 cm), después de unos 3,5 cm hacemos pequeños
pliegues.
Ahora omita la distancia entre las siguientes filas. Vuelva a coser el cordón de algodón entre las dos filas siguientes,
haciendo dobleces (ancho del cordón 1 cm). Y
salte la distancia entre las filas nuevamente y cosa el cordón nuevamente entre las filas siguientes.
Haga lazos (5 piezas) con una cinta de raso y cosa a lo largo de la fila inferior de encaje donde
hecho pliegues.
Coser las cuentas después de otra fila, dejando bucles, las cuentas parecen colgar.
Ate la fila superior de la gorguera con hilo en color sc, haciendo sc en cada bucle.
Decora la parte superior como desees. Hice un moño, recogí las cuentas en un hilo y cosí en la parte superior.
Estar.
Corta un trozo de alambre de unos 24 cm. Si desea que la pierna sea más corta o más larga, corte el cable al tamaño
correcto. Cubrimos el alambre con pegamento en el momento en que el cristal y pegamos el cordel al alambre. Dejamos
que se seque, pero por ahora hacemos la parada más.
Giramos y doblamos el cable en ambos lados (ver foto). Tengo una pierna de 10 cm.
Pegue un lado dentro del soporte. Para mayor resistencia y estabilidad, puedes poner plastilina.
Pega el otro lado de la pierna a la parte inferior del árbol de Navidad. Pegué la pierna por un súper momento.
Corta 3-4 círculos según el tamaño del soporte (ver foto), coloca dentro del soporte, pega el último círculo.
Legend:
p. – loop
ch – air loop
sc – single crochet
Herringbone base
We put more filler, then we knit the top, do not put the filler in the top.
(SL-ST, 3ch, 2DC, 3ch, SL-ST) – in one loop, skip one loop. So we knit to the end of the row.
Sew cotton lace between the last two rows (lace width 2cm), after about 3.5cm we make small folds.
Now skip the distance between the next rows. Sew cotton lace again between the next two rows, making folds (lace
width 1cm). AND
skip the distance between the rows again, and sew lace again between the next rows.
Make bows (5pcs) from a satin ribbon and sew along the bottom row of lace where
made folds.
Sew on the beads after another row, leaving loops, the beads seem to hang.
Tie the topmost row of the ruff with yarn in color sc, making sc in each loop.
Decorate the top as desired. I made a bow, gathered the beads on a thread and sewed on the very top.
Stand.
We cut out a circle of plastic to the size of the bottom, glue it.
Cut off a piece of wire about 24cm. If you want the leg to be shorter or longer, cut the wire to the correct size. We coat
the wire with glue the moment the crystal and glue the twine to the wire. We leave to dry, but for now we make the
stand further.
We glue the twine first to the bottom, and then along the entire stand.
We twist and bend the wire on both sides (see photo). I got a 10cm leg.
Glue one side inside the stand. For strength and stability, you can put plasticine.
Glue the other side of the leg to the bottom of the Christmas tree. I glued the leg for a super moment.
Cut 3-4 circles according to the size of the stand (see photo), put inside the stand, glue the last circle.