Documentos de Académico
Documentos de Profesional
Documentos de Cultura
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E Engine (SEBP3526 - 81) - Systems & Components C3 PDF
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E Engine (SEBP3526 - 81) - Systems & Components C3 PDF
Pantalla anterior
Bienvenido: cr461jb1
Producto: CARGADOR DE RUEDAS
Modelo: 924G CARGADOR DE RUEDAS RBB
Configuración: Cargador de ruedas 924G 924Gz RBB00001-UP (MÁQUINA)
CON EL MOTOR 3056E
Especificaciones
Portaherramientas integrado IT28G y tren de fuerza de cargadores de ruedas 924G, 924GZ y 928G
Número de medio -RENR6424-02 Fecha de publicación -01/05/2012 Fecha actualizada -03/05/2012
i02818872
Freno y planetario
SMCS - 4011
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 1/3
24/8/2020 924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E Engine(SEBP3526 - 81) - Systems & Components
Ilustración 1 g01406567
(1) Lubrique ligeramente los sellos del anillo en D con el lubricante que se va a sellar.
(A) Espesor del disco de fricción 250-1844 ... 7,80 ± 0,08 mm (0,307 ± 0,003 pulgadas)
(B) Diámetro del eje planetario ... 35,253 ± 0,008 mm (1,3879 ± 0,0003 pulgadas)
(D) Inside diameter of the planetary gear ... 43.218 ± 0.010 mm (1.7015 ± 0.0004 inch)
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 2/3
24/8/2020 924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E Engine(SEBP3526 - 81) - Systems & Components
Note: Apply a thin coat of lubricant on the sleeve bearing with the lubricant of the final drive before assembly.
(E) Inside diameter of the sleeve bearing ... 35.301 ± 0.013 mm (1.3898 ± 0.0005 inch)
(F) Average outside diameter of the sleeve bearing ... 43.117 ± 0.013 mm (1.6975 ± 0.0005 inch)
Note: The openings of the spring pins (3) and (4) are 180 degrees from each other. The openings of the spring
pins (3) and (4) are parallel to the carrier.
(G) Deform pin holes lightly with a chisel. ... 1.5 mm (0.06 inch)
Copyright 1993 - 2020 Caterpillar Inc. Mon Aug 24 2020 06:27:05 GMT-0500 (hora estándar de Colombia)
All Rights Reserved.
cr461jb1
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 3/3