Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Configure un aviso de mensaje del día (MOTD) para advertir a los usuarios que
8 el acceso no autorizado
está prohibido
25
26
27
28
Respuesta
Ingrese a las Pc y asigne ip, mask y gateway según como le indican en la hoja
Ingrese el comando
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#no ip domain-lookup
Ingrese el comando
Router>enable
Router#configure terminal
Router(config)# hostname R1
Resultado
R1(config)#
Ingrese el comando
R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#logging synchronous
R1(config-line)#exit
R1(config)#
Ingrese el comando
R1(config)#line vty 0 15
R1(config-line)#password cisco
R1(config-line)#logging synchronous
R1(config-line)#exit
Ingrese el comando
R1(config)#enable secret class
Ingrese el comando
R1(config)#line console 0
R1(config-line)#logging synchronous
R1(config-line)#exit
R1(config)#
Ingrese el comando
banner motd "Acceso solo a personal autorizado"
Ingrese el comando
R1(config)#service password-encryption
Ingrese el comando
R1(config)#interface gigabitEthernet 0/0
R1(config-if)#ip 192.168.1.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#
Ingrese el comando
R1(config)#interface serial 0/0/0
R1(config-if)#ip address 192.168.12.1 255.255.255.252
R1(config-if)#clock rate 4000000
R1(config-if)#no shutdown
Ingrese el comando
R1(config)#interface serial 0/0/1
R1(config-if)#ip address 192.168.13.1 255.255.255.252
R1(config-if)#no shutdown
Ingrese el comando
R1(config)#interface g0/0
R1(config-if)#ipv6 address 2001:DB8:ACAD:A::1/64
R1(config-if)#ipv6 address FE80::1 link-local
R1(config-if)#exit
R1(config)#ipv6 unicast-routing
Ingrese el comando
R1(config)#router eigrp 1
R1(config-router)#do show ip route connected
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
C 192.168.12.0/30 is directly connected, Serial0/0/0
C 192.168.13.0/30 is directly connected, Serial0/0/1
R1(config-router)#network 192.168.1.0 0.0.0.255
R1(config-router)#network 192.168.12.0 0.0.0.3
R1(config-router)#network 192.168.13.0 0.0.0.3
R2>enable
Password:
R2#configure terminal
R2(config)#router eigrp 1
R2(config-router)#do show ip route connected
C 192.168.2.0/24 is directly connected, GigabitEthernet0/0
C 192.168.12.0/30 is directly connected, Serial0/0/0
C 192.168.23.0/30 is directly connected, Serial0/0/1
R2(config-router)#passive-interface g0/0
R1>enable
Password:
R1#show ip protocols
Resultado
R1(config)#inter loopback 5
R1(config-if)#
%LINK-5-CHANGED: Interface Loopback5, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback5, changed state to up
R1(config-if)#ip address 192.168.11.5 255.255.255.252
R1(config-if)#interface loopback 13
R1(config-if)#
%LINK-5-CHANGED: Interface Loopback13, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback13, changed state to
up
R1(config-if)#ip address 192.168.11.13 255.255.255.252
R1(config)#route eigrp 1
R1(config-router)#do show ip route connected
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
C 192.168.11.0/30 is directly connected, Loopback1
C 192.168.11.4/30 is directly connected, Loopback5
C 192.168.11.8/30 is directly connected, Loopback9
C 192.168.11.12/30 is directly connected, Loopback13
C 192.168.12.0/30 is directly connected, Serial0/0/0
C 192.168.13.0/30 is directly connected, Serial0/0/1