Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Océ - Colorado - 1650 DOBLE CARA PDF
Océ - Colorado - 1650 DOBLE CARA PDF
us (cifrado)
(/tsm?tsm=TSM000295EN.US&sessionid=1579177296536)
localhost:20346/tsm?tsm=TSM000295EN.US#homePage 1/4
16/1/2020 TSM Océ Colorado 1650 en.us (cifrado)
Be aware you have to rotate the job for the inside 180 degrees.
The lead-in and lead-out images are used by the AAC to measure and correct for
additional media step errors caused by the ink layer of side 1, while printing side 2.
Procedure
1. Load an empty take-up roll core onto the roll winder.
localhost:20346/tsm?tsm=TSM000295EN.US#homePage 2/4
16/1/2020 TSM Océ Colorado 1650 en.us (cifrado)
2. Load a media roll on position 1 in the media drawer, see "Load a media roll
(position 1)" in the operation guide.
3. On the operator panel tap on the [Media] icon on the right.
Select the required media and media width.
4. Tap on [Feed]. The printer feeds the media in the correct position to start
printing.
5. Tape rst the center and then the sides of the media to the core.
6. Place the tension bar lever in locked position and place the tension bar.
7. Move the media guides towards the middle to align with the media.
8. Prepare a nest of prints for the outside of the media in one of the supported
RIP software applications.
In ONYX the nesting function is called [Group jobs]. Change the group setting
from [Conserve media] to [Group jobs together]. The RIP will treat all jobs in
the group as 1 image.
The nest includes:
a leading strip
a lead-in image (in any color)
the user images
a lead-out image (in any color)
a trailing strip with a line (this is a self made image with a cutting line at
the end)
NOTE
Please note that when you apply additional space between the separate
images, you have to subtract this additional space from the 1600 mm at the
trailing edge.
9. Submit the job to the printer.
10. Cut the media beneath the printed line.
11. Remove the tension bar.
12. Move the media guides to the side.
13. Remove the take-up media roll from the winder, see "Unload a take-up media
roll from the roll winder" in the operation guide.
14. Cut the media precisely on the printed line. Do this outside of the printer.
15. Place a new empty take-up roll core and push the media shaft back on the
winder.
16. Remove the media roll from position 1 in the media drawer, see "Unload a
media roll from the drawer" in the operation guide.
17. Load the media roll for inside printing on position 2 in the media drawer, see
"Load a media roll for inside printing" in the operation guide.
18. Tap on the [Media] icon on the right.
19. Tap on [Feed]. The printer feeds the media in the correct position to start
printing.
20. Tape rst the center and then the sides of the media to the core.
21. Place the tension bar lever in locked position and place the tension bar.
22. Move the media guides towards the middle to align with the media.
23. Prepare the nest of prints for the second side of the double-sided print in one
of the supported RIP software applications.
The nest includes:
a leading strip
a lead-in image (in any color)
the user images
NOTE
localhost:20346/tsm?tsm=TSM000295EN.US#homePage 3/4
16/1/2020 TSM Océ Colorado 1650 en.us (cifrado)
Depending on the application you may need to rotate or mirror the images for
side 2.
NOTE
Cambie la tira nal a 0 mm en [Con guración predeterminada] en el panel
del operador.
24. Envíe el trabajo a la impresora.
localhost:20346/tsm?tsm=TSM000295EN.US#homePage 4/4