Documentos de Académico
Documentos de Profesional
Documentos de Cultura
DATOS GENERALES
DATOS DEL GENERADOR TRANSFORMADORES DE CORRIENTE (TERMINAL)
TRANSFORMADORES DE CORRIENTE (NEUTRO) TRANSFORMADOR DE TENSION
RELACIONES DE IMPEDANCIA
VALORES DE AJUSTE
@ AJUSTES GENERALES 87N Restricted earth fault protection (PDIF)
87G Generator differential protection (PDIF) 21 Full-scheme distance measuring, Mho characteristic, PDIS (Impedance Protection)
RDIR Directional impedance Mho 78 Pole slip protection (PPAM).(PERDIDA DE SINCRONISMO)
40 Loss of excitation (PDIS). (PERDIDA DE EXCITACIÓN) 50 INSTANTANEOUS PHASE OVERCURRENT PROTECTION (PIOC)
51_67 Four step phase overcurrent protection (PTOC) 50N INSTANTANEOUS RESIDUAL OVERCURRENT PROTECTION (PIOC)
51N/67NFour step residual overcurrent protection (PTOC) 67N Sensitive directional residual overcurrent and power protection (PSDE)
49 Thermal overload protection, two time constants (PTTR) 50BF Breaker failure protection (RBRF)
DATOS GENERALES
DATOS DEL GENERADOR
DATOS DEL GENERADOR
Características nominales
Tipo (CH=Hidráulica, D=Diesel, TV=Turb.Vapor, TG=Turb.Gas, etc.) - CH
Potencia activa nominal MW 1.06
Potencia aparente nominal MVA 1.25
Factor de potencia nominal - 0.85
Potencia activa máxima MW
Potencia activa mínima MW
Potencia reactiva máxima MVAr
Potencia reactiva mínima MVAr
Tensión nominal primaria entre fases kV 4.16
Rango de tensión entre fases %
Velocidad de rotación rpm
Frecuencia Hz 0
Características operativas
Reactancia de secuencia positiva, subtransitoria, no saturada. pu 0.131
Reactancia de secuencia negativa, no saturada. pu 0.147
Reactancia de secuencia cero. pu 0.100
Resistencia estatórica. ohm/fase
TRANSFORMADORES DE CORRIENTE (TERMINAL)
Marca - -
Tipo - -
Modelo - -
Cantidad de núcleos - -
Corriente nominal A - 5 200 5 200
Relación de transformación - - 40.00 40.00
Clase - -
Prestación VA - 40 40
TRANSFORMADORES DE CORRIENTE (NEUTRO)
Marca - -
Tipo - -
Modelo - -
Cantidad de núcleos - -
Corriente nominal A -
Relación de transformación - - #DIV/0! #DIV/0!
Clase - -
Prestación VA - 40 40
TRANSFORMADOR DE TENSION
Marca - -
Tipo - -
Modelo - -
Cantidad de arrollamientos - -
Tensión nominal entre fases V - 100 4160 100 4160
Relación de transformación - - 62.50 62.50
Clase - - 3 3
Prestación VA - 50 50
RELACIONES DE IMPEDANCIA
Relación secundario/primario (Zs/Zp = Us/Is:Up/Ip) - - 0.96 0.96
Relación primario/secundario (Zp/Zs = Up/Ip:Us/Is) - - 1.04 1.04
VALORES DE AJUSTE
AJUSTES GENERALES Disp.s/interr.:
Configuración del Alcance de las Funciones Disponibles
87N 87N Restricted earth fault protection (PDIF) - Enabled - Disabled Disabled - Disabled -
87G 87G Generator differential protection (PDIF) - Enabled - Disabled Enabled - Enabled -
21 21 Impedance Protection, PDIS - Enabled - Disabled Disabled - Disabled -
RDIR RDIR Directional impedance Mho - Enabled - Disabled Disabled - Disabled -
78 78 Pole slip protection (PPAM). - Enabled - Disabled Disabled - Disabled -
40 40 Loss of excitation (PDIS). - Enabled - Disabled Enabled - Enabled -
50 50 Instantaneous phase overcurrent protection (PIOC) - Enabled - Disabled Disabled - Disabled -
51_67 51_67 Four step phase overcurrent protection (PTOC) - Enabled - Disabled Enabled - Enabled -
50N 50N Instantaneous residual overcurrent protection (PIOC) - Enabled - Disabled Disabled - Disabled -
51N/67N 51N/67N Four step residual overcurrent protection (PTOC) - Enabled - Disabled Disabled - Disabled -
67N 67N Sensitive directional residual overcurrent and power - Enabled - Disabled Disabled - Disabled -
protection (PSDE)
49 49 Thermal overload protection, two time constants (PTTR) - Enabled - Disabled Disabled - Disabled -
50BF 50BF Breaker failure protection (RBRF) - Enabled - Disabled Disabled - Disabled -
52PD 52PD Pole discrepancy protection (RPLD) - Enabled - Disabled Disabled - Disabled -
37 37 Directional underpower protection (PDUP) - Enabled - Disabled Enabled - Enabled -
32 32 Directional overpower protection (PDOP) - Enabled - Disabled Enabled - Enabled -
27 27 Two step undervoltage protection (PTUV) - Enabled - Disabled Enabled - Enabled -
59 59 Two step overvoltage protection (PTOV) - Enabled - Disabled Enabled - Enabled -
59N 59N Two step residual overvoltage protection (PTOV) - Enabled - Disabled Disabled - Disabled -
24 24 Overexcitation protection (PVPH) - Enabled - Disabled Disabled - Disabled -
60 60 Voltage differential protection (PTOV) - Enabled - Disabled Disabled - Disabled -
59TH 59TH 95% and 100% Stator earthground fault protection based - Enabled - Disabled Disabled - Disabled -
81 on
81 3rd harmonic
Underfrequency protection (PTUF) - Enabled - Disabled Enabled - Enabled -
81 81 Overfrequency protection (PTOF) - Enabled - Disabled Enabled - Enabled -
81 81 Rate-of-change frequency protection (PFRC) - Enabled - Disabled Disabled - Disabled -
25 Synchronizing (RSYN,25) - Enabled - Disabled Enabled - Enabled -
87N Restricted earth fault protection (PDIF)
Operation Operación Off / On - ON - OFF - -
380200604.xls 02/28/2018 1 de 3
BASE DE DATOS DE AJUSTE DE PROTECCIONES
Tipo: PROTECCION GENERADOR Tipo Central: HIDROELECTRICA Región: ZONA SUR
Fabricante: ABB C.H.: CHARCANI I Dpto:
Modelo: REG670 Tensión Nom.: 4,16 kV Empresa:
Versión: Grupo Gen.: G1-G2 Diag.Unif.N°:
N° Serie: Uprim[kV]: 4.16kV Man.Serv.N°:
Tecnología: NUMÉRICA Fases: RSTN Fecha: 13-Feb-14
Año instal.: Ucc [V]: Respons.: K.V.H.
Código: Uca [V]: 100 Revisión: 0
Ubic.Tabl: Ica [A]: 5
Sistema: PRINCIPAL Frec.[Hz]: 60
DESCRIPCION DE LOS AJUSTES GRUPO 1 (AS BUILT) GRUPO 1 (AECP 2014) OBSERVACIONES
ACTUAL PROPUESTO
ANSI COD DESCRIPCION UNIDAD MIN MAX PASO SECUNDARIO PRIMARIO SECUNDARIO PRIMARIO
Tau2 Time constant with cooling input in min, with IBase2 Min 1.0 500.0 1.0 - -
IHighTau1 Current Sett, in % of IBase1 for rescaling TC1 by TC1-IHIGH %IB1 30.0 250.0 1.0 - -
Tau1High Multiplier in % to TC1 when current is > IHIGH-TC1 %tC1 5 2000 1 - -
ILowTau1 Current Set, in % of IBase1 for rescaling TC1 by TC1-ILOW %IB1 30.0 250.0 1.0 - -
Tau1Low Multiplier in % to TC1 when current is < ILOW-TC1 %tC1 5 2000 1 - -
IHighTau2 Current Set, in % of IBase2 for rescaling TC2 by TC2-IHIGH %IB2 30.0 250.0 1.0 - -
Tau2High Multiplier in % to TC2 when current is >IHIGH-TC2 %tC2 5 2000 1 - -
ILowTau2 Current Set, in % of IBase2 for rescaling TC2 by TC2-ILOW %IB2 30.0 250.0 1.0 - -
Tau2Low Multiplier in % to TC2 when current is < ILOW-TC2 %tC2 5 2000 1 - -
Itrip Steady state operate current level in % of IBasex %IBx 50.0 250.0 1.0 - -
Alarm1 First alarm level in % of heat content trip value %Itr 50.0 99.0 1.0 - -
Alarm2 Second alarm level in % of heat content trip value %Itr 50.0 99.0 1.0 - -
LockoutReset Lockout reset level in % of heat content trip value %Itr 10.0 95.0 1.0 - -
ThetaInit Initial Heat content, in % of heat content trip value % 0.0 95.0 1.0 - -
Warning Time setting, below which warning would be set Min 1.0 500.0 0.1 - -
tPulse Length of the pulse for trip signal (in msec). s 0.01 0.30 0.01 - -
50BF Breaker failure protection (RBRF)
Disabled
Operation Disable/Enable Operation - OFF - OFF -
Enabled
52PD Pole discrepancy protection (RPLD)
Disabled
Operation Disable/Enable Operation - - -
Enabled
37 Directional underpower protection (PDUP)
IBase Current-Reference (primary current A) (IBase) A 1 99999 1 153.00 153.00
VBase Voltage-Reference (primary voltage kV) (VBase) KV 0.05 2000.00 0.05 5.25 5.25
Mode A, B, C BC
Arone CA
Selection of measured current and voltage (Mode) - Pos Seq A Pos Seq - Pos Seq -
AB B
C
Disabled
Operation Disable/Enable Operation - OFF - OFF -
Enabled
K Low pass filter coefficient for power measuremt, P and Q (K) - 0.00 0.99 0.01 - -
IMagComp5 Magnitude factor to calibrate current at 5% of In % -10.000 10.000 0.001 - -
IMagComp30 Magnitude factor to calibrate current at 30% of In % -10.000 10.000 0.001 - -
IMagComp100 Magnitude factor to calibrate current at 100% of In % -10.000 10.000 0.001 - -
VMagComp5 Magnitude factor to calibrate voltage at 5% of Vn % -10.000 10.000 0.001 - -
VMagComp30 Magnitude factor to calibrate voltage at 30% of Vn % -10.000 10.000 0.001 - -
VMagComp100 Magnitude factor to calibrate voltage at 100% of Vn % -10.000 10.000 0.001 - -
IAngComp5 Angle calibration for current at 5% of In Deg -10.000 10.000 0.001 - -
IAngComp30 Angle calibration for current at 30% of In Deg -10.000 10.000 0.001 - -
IAngComp100 Angle calibration for current at 100% of In Deg -10.000 10.000 0.001 - -
Step 1
OpMode1 - Disabled UnderPower UnderPowe
Operation mode 1 UnderPower - -
r
Power1 Power setting for stage 1 in % of Sbase %SB 0.0 500.0 0.1 5.00 - 5.00 -
Angle1 Angle for stage 1 Deg -180.0 180.0 0.1 0.00 - 0.00 -
TripDelay1 Trip delay for stage 1 s 0.010 6000.000 0.001 30.00 - 30.00 -
DropDelay1 Drop delay for stage 1 s 0.010 6000.000 0.001 1.00 - 1.00 -
Hysteresis1 Absolute hysteresis of stage 1 pu 0.2 5.0 0.1 - -
Step 2
OpMode2 Disabled UnderPowe
Operation mode 2 - UnderPower - -
OverPower r
Power2 Power setting for stage 2 in % of Sbase %SB 0.0 500.0 0.1 5.00 - 5.00 -
Angle2 Angle for stage 2 Deg -180 180.0 0.1 0.00 - 0.00 -
TripDelay2 Trip delay for stage 2 s 0.010 6000.000 0.001 5.00 - 5.00 -
DropDelay2 Drop delay for stage 2 s 0.010 6000.000 0.001 1.00 - 1.00 -
Hysteresis2 Absolute hysteresis of stage 2 pu 0.2 5.0 0.1 - -
32 Directional overpower protection (PDOP)
IBase Current-Reference (primary current A) A 1 99999 1 153.00 153.00
VBase Voltage-Reference (primary voltage kV) KV 0.05 2000.00 0.05 5.25 5.25
Mode A, B, C BC
Arone CA
Selection of measured current and voltage - Pos Seq A Pos Seq - Pos Seq -
AB B
C
Disabled
Operation Disable/Enable Operation - ON - ON -
Enabled
K Low pass filter coefficient for power measurement, P and Q - 0.00 0.99 0.01 - - - -
IMagComp5 Magnitude factor to calibrate current at 5% of In % -10.000 10.000 0.001 - - - -
IMagComp30 Magnitude factor to calibrate current at 30% of In % -10.000 10.000 0.001 - - - -
IMagComp100 Magnitude factor to calibrate current at 100% of In % -10.000 10.000 0.001 - - - -
VMagComp5 Magnitude factor to calibrate voltage at 5% of Vn % -10.000 10.000 0.001 - - - -
VMagComp30 Magnitude factor to calibrate voltage at 30% of Vn % -10.000 10.000 0.001 - - - -
VMagComp100 Magnitude factor to calibrate voltage at 100% of Vn % -10.000 10.000 0.001 - - - -
IAngComp5 Angle calibration for current at 5% of In Deg -10.000 10.000 0.001 - - - -
IAngComp30 Angle calibration for current at 30% of In Deg -10.000 10.000 0.001 - - - -
IAngComp100 Angle calibration for current at 100% of In Deg -10.000 10.000 0.001 - - - -
Step 1
OpMode1 Operation mode 1 - Disabled Over Power - Over Power -
OverPower
Power1 Power setting for stage 1 in % of Sbase %SB 0.0 500.0 0.1 10.00 - 10.00 -
Angle1 Angle for stage 1 Deg -180.0 180.0 0.1 180.00 - 180.00 -
TripDelay1 Trip delay for stage 1 s 0.010 6000.000 0.001 5.00 - 5.00 -
DropDelay1 Drop delay for stage 1 s 0.010 6000.000 0.001 1.00 - 1.00 -
Hysteresis1 Absolute hysteresis of stage 1 in % of Sbase pu 0.2 5.0 0.1 - - - -
Step 2
OpMode2 Disabled
Operation mode 2 - OFF - OFF -
OverPower
Power2 Power setting for stage 2 in % of Sbase %SB 0.0 500.0 0.1 - -
Angle2 Angle for stage 2 Deg -180 180.0 0.1 - -
TripDelay2 Trip delay for stage 2 s 0.010 6000.000 0.001 - -
DropDelay2 Drop delay for stage 2 s 0.010 6000.000 0.001 - -
Hysteresis2 Absolute hysteresis of stage 2 in % of Sbase pu 0.2 5.0 0.1 - -
VOLTAGE PROTECTION
27 Two step undervoltage protection (PTUV)
ConnType PhN DFT
PhPh RMS
Group selector for connection type - PhN RMS PhN DFT - PhN DFT -
PhPh DFT
VBase Voltage-Reference (primary voltage kV) KV 0.05 2000.00 0.05 - 5.25 - 5.25
Step 1
OperationStep1 Enable execution of step 1 - Off / On ON - ON -
OpMode1 1 out of 3
Number of phases required for op (1 of 3, 2 of 3, 3 of 3) from step
- 2 out of 3 1 out of 3 - 1 out of 3 -
1 3 out of 3
Pickup1 (U1<) Voltage pickup value (Definite-Time & Inverse-Time curve) in % %UB 1 100 1 80.00 - 80.00 -
of VBase, step 1
t1 Definitive time delay of step 1 s 0.00 6000.00 0.01 5.00 - 5.00 -
tReset1 Reset time delay used in IEC Definite Time curve step 1 s 0.000 60.000 0.001 - -
t1Min Minimum operate time for inverse curves for step 1 s 0.000 60.000 0.001 5.00 - 5.00 -
Instantaneous
Frozen timer
ResetTypeCrv1 Selection of reset curve type for step 1 - Linearly - -
decreased
tIReset1 Time delay in Inverse- Time reset (s), step 1 s 0.000 60.000 0.001 - -
TD1 (K1) Time multiplier for the inverse time delay for step 1 - 0.05 1.10 0.01 0.05 - 0.05 -
ACrv1 Parameter A for customer programmable curve for step 1 - 1.000 200.000 0.001 - -
BCrv1 Parameter B for customer programmable curve for step 1 - 1.00 100.00 0.01 - -
CCrv1 Parameter C for customer programmable curve for step 1 - 0.0 1.0 0.1 - -
DCrv1 Parameter D for customer programmable curve for step 1 - 0.000 60.000 0.001 - -
PCrv1 Parameter P for customer programmable curve for step 1 - 1.000 3.000 0.001 - -
CrvSat1 Tuning param for prog. under voltage Inverse- Time curve, step % 0 100 1 - -
1 Off
IntBlkSel1 Internal (low level) blocking mode, step 1 - Block of trip Block all - Block all -
Block all
IntBlkStVal1 Voltage setting for internal blocking in % of VBase, step 1 %UB 1 100 1 20.00 - 20.00 -
tBlkUV1 Time delay of internal (low level) blocking for step 1 s 0.000 60.000 0.001 0.00 - 0.00 -
HystAbs1 Absolute hysteresis in % of VBase, step 1 %UB 0.00 100.00 0.01 0.50 - 0.50 -
Step 2
OperationStep2 Enable execution of step 2 - Off / On OFF - OFF -
VBase Voltage-Reference (primary voltage kV) (VBase) KV 0.05 2000.00 0.05 5.25 5.25
Step 1
Disabled
OperationStep1 Enable execution of step 1 - ON - ON -
Enabled
Characterist1 Definite time
Inverse curve A
Definite
Selection of time delay curve type for step 1 - Inverse curve B Definite time - -
time
Inverse curve C
Prog. inv. Curve
OpMode1 1 out of 3
Number of phases required for op (1 of 3, 2 of 3, 3 of 3) from step
- 2 out of 3 1 out of 3 - 1 out of 3 -
1
3 out of 3
Pickup1 (U1>) Voltage pickup value (Definite-Time & Inverse-Time curve) in % %VB 1 200 1
115.00 115.00
of VBase, step 1
t1 Definitive time delay of step 1 s 0.00 6000.00 0.01 5.00 - 5.00 -
tReset1 Reset time delay used in IEC Definite Time curve step s 0.000 60.000 0.001 - -
t1Min Minimum operate time for inverse curves for step 1 s 0.000 60.000 0.001 5.00 - 5.00 -
Instantaneous
Frozen timer
ResetTypeCrv1 Selection of reset curve type for step 1 - - -
Linearly
decreased
tIReset1 Time delay in Inverse- Time reset (s), step 1 s 0.000 60.000 0.001 - -
TD1 (K1) Time multiplier for the inverse time delay for step 1 - 0.05 1.10 0.01 - -
ACrv1 Parameter A for customer programmable curve for step 1 - 1.000 200.000 0.001 - -
BCrv1 Parameter B for customer programmable curve for step 1 - 1.00 100.00 0.01 - -
CCrv1 Parameter C for customer programmable curve for step 1 - 0.0 1.0 0.1 - -
DCrv1 Parameter D for customer programmable curve for step 1 - 0.000 60.000 0.001 - -
PCrv1 Parameter P for customer programmable curve for step 1 - 1.000 3.000 0.001 - -
CrvSat1 Tuning param for prog. under voltage Inverse- Time curve, step % 0 100 1 - -
HystAbs1 1
Absolute hysteresis in % of VBase, step 1 %VB 0.00 100.00 0.01 - -
Step 2
Disabled
OperationStep2 Enable execution of step 2 - Enable - Enable -
Enabled
Characterist2 Definite time
Inverse curve A
Definite
Selection of time delay curve type for step 2 - Inverse curve B Definite time - -
time
Inverse curve C
Prog. inv. Curve
OpMode2 1 out of 3
Number of phases required for op (1 of 3, 2 of 3, 3 of 3) from step
- 2 out of 3 1 out of 3 - 1 out of 3 -
2
3 out of 3
Pickup2 (U2>) Voltage pickup value (Definite-Time & Inverse-Time curve) in % %VB 1 200 1 130.00 - 130.00 -
of VBase, step 2
t2 Definitive time delay of step 2 s 0.000 60.000 0.001 0.50 - 0.50 -
tReset2 Reset time delay used in IEC Definite Time curve step 2 s 0.000 60.000 0.001 - -
t2Min Minimum operate time for inverse curves for step 2 s 0.000 60.000 0.001 5.00 - 5.00 -
Instantaneous
Frozen timer
ResetTypeCrv2 Selection of reset curve type for step 2 - - -
Linearly
decreased
tIReset2 Time delay in Inverse-Time reset (s), step 2 s 0.000 60.000 0.001 - -
TD2 (K2) Time multiplier for the inverse time delay for step 2 - 0.05 1.10 0.01 0.05 - 0.05 -
ACrv2 Parameter A for customer programmable curve for step 2 - 1.000 200.000 0.001 - -
BCrv2 Parameter B for customer programmable curve for step 2 - 1.00 100.00 0.01 - -
CCrv2 Parameter C for customer programmable curve for step 2 - 0.0 1.0 0.1 - -
DCrv2 Parameter D for customer programmable curve for step 2 - 0.000 60.000 0.001 - -
PCrv2 Parameter P for customer programmable curve for step 2 - 1.000 3.000 0.001 - -
CrvSat2 Tuning param for prog. under voltage Inverse- Time curve, step % 0 100 1 - -
HystAbs2 2Absolute hysteresis in % of VBase, step 2 %VB 0.0 100.0 0.1 0.50 - 0.50 -
59N Two step residual overvoltage protection (PTOV)
Operation Disable/Enable Operation - Disabled OFF - OFF -
Enabled
Vbase Voltage-Reference (primary voltage kV) KV 0.05 2000.00 0.05 - 5.25 - 5.25
Step 1
Disabled
OperationStep1 Enable execution of step 1 - ON - ON -
Enabled
Characterist1 Definite time
Inverse curve A Definite
Selection of time delay curve type for step 1 - Inverse curve B Definite time - -
Inverse curve C time
Prog. inv. Curve
OpMode1 1 out of 3
Number of phases required for op (1 of 3, 2 of 3, 3 of 3) from step
- 2 out of 3 5.00 - 5.00 -
1
3 out of 3
Pickup1 (U1>) Voltage pickup value (Definite-Time & Inverse-Time curve) in % %VB 1 200 1 2.00 2.00
- -
of VBase, step 1
t1 Definitive time delay of step 1 s 0.00 6000.00 0.01 5.00 - 5.00 -
tReset1 Reset time delay used in IEC Definite Time curve step 1 s 0.000 60.000 0.001 - -
t1Min Minimum operate time for inverse curves for step 1 s 0.000 60.000 0.001 0.05 - 0.05 -
Instantaneous
Frozen timer
ResetTypeCrv1 Selection of reset curve type for step 1 - - -
Linearly
decreased
tIReset1 Time delay in Inverse- Time reset (s), step 1 s 0.000 60.000 0.001 - -
TD1 (K1) Time multiplier for the inverse time delay for step 1 - 0.05 1.10 0.01 0.50 - 0.50 -
ACrv1 Parameter A for customer programmable curve for step 1 - 1.000 200.000 0.001 - -
BCrv1 Parameter B for customer programmable curve for step 1 - 1.00 100.00 0.01 - -
CCrv1 Parameter C for customer programmable curve for step 1 - 0.0 1.0 0.1 - -
DCrv1 Parameter D for customer programmable curve for step 1 - 0.000 60.000 0.001 - -
PCrv1 Parameter P for customer programmable curve for step 1 - 1.000 3.000 0.001 - -
CrvSat1 Tuning param for prog. under voltage Inverse- Time curve, step % 0 100 1 - -
HystAbs1 1
Absolute hysteresis in % of VBase, step 1 %VB 0.00 100.00 0.01 - -
Step 2
Disabled
OperationStep2 Enable execution of step 2 - - -
Enabled
24 Overexcitation protection (PVPH)
MeasuredV PosSeq
AB
Selection of measured voltage (MeasuredV) - BC - -
CA
MeasuredI AB
BC
Selection of measured current (MeasuredI) - CA - -
PosSeq
Disabled
Operation Disable/Enable Operation - - -
Enabled
IBase Base current (rated phase current) in A A 1 99999 1 3930.00 3930.00
VBase Base voltage (main voltage) in kV kV 0.05 2000.00 0.05 12.50 12.50
Pickup1 (V/Hz>) Operate level of V/Hz at no load and rated freq in % of %VB/f 100.0 180.0 0.1 - -
Pickup2 (V/Hz>>) (Vbase/frated)
High level of V/Hz above which tMin is used, in % of (Vbase/fn) %VB/f 100.0 200.0 0.1 - -
Xleakage Winding leakage reactance in primary ohms ohm 0.000 200.000 0.001 - -
t_TripPulse Length of the pulse for trip signal (in sec) s 0.000 60.000 0.001 - -
t_MinTripDelay Minimum trip delay for V/ Hz inverse curve, in sec s 0.000 60.000 0.001 - -
t_MaxTripDelay Maximum trip delay for V/ Hz inverse curve, in sec s 0.00 9000.00 0.01 - -
t_CoolingK Transformer magnetic core cooling time constant, in sec s 0.10 9000.00 0.01 - -
CurveType Inverse time curve selection, IEEE/Tailor made - IEEE - -
Tailor made
TDForIEEECurve Time multiplier for IEEE inverse type curve - 1 60 1 - -
t1_UserCurve Time delay t1 (longest) for tailor made curve, in sec (t1Tailor) s 0.00 9000.00 0.01 - -
t2_UserCurve Time delay t2 for tailor made curve, in sec (t2Tailor) s 0.00 9000.00 0.01 - -
t3_UserCurve Time delay t3 for tailor made curve, in sec (t3Tailor) s 0.00 9000.00 0.01 - -
t4_UserCurve Time delay t4 for tailor made curve, in sec (t4Tailor) s 0.00 9000.00 0.01 - -
t5_UserCurve Time delay t5 for tailor made curve, in sec (t5Tailor) s 0.00 9000.00 0.01 - -
t6_UserCurve Time delay t6 (shortest) for tailor made curve, in sec (t6Tailor) s 0.00 9000.00 0.01 - -
AlarmPickup Alarm pickup level as % of Step1 trip pickup level % 50.00 120.00 0.1 - -
tAlarm Alarm time delay, in sec s 0.00 9000.00 0.01 - -
60 Voltage differential protection (PTOV)
Disabled
Operation Disable/Enable Operation - Enabled - -
VBase Base Voltage (VBase) kV 0.05 2000.00 0.05 - 400.00 - 400.00
No
BlkDiffAtULow Block operation at low voltage (BlkDiffAtULow) - - -
Yes
VDTrip Operate level, in % of VBase %UB 1.0 100.0 0.1 - -
tTrip Time delay for voltage differential operate, in milliseconds s 0.000 60.000 0.001 - -
tReset Time delay for voltage differential reset, in seconds s 0.000 60.000 0.001 - -
V1Low Input 1 undervoltage level, in % of VBase %UB 0.0 100.0 0.1 - -
V2Low Input 2 undervoltage level, in % of VBase %UB 0.0 100.0 0.1 - -
tBlock Reset time for undervoltage block s 0.000 60.000 0.001 - -
VDAlarm Alarm level, in % of VBase %UB 0.0 100.0 0.1 - -
tAlarm Time delay for voltage differential alarm, in seconds s 0.000 60.000 0.001 - -
RF_A Ratio compensation factor phase A VCap*RF_A=VBus_A - 0.000 3.000 0.001 - -
RF_B Ratio compensation factor phase B VCap*RF_B=VBus_B - 0.000 3.000 0.001 - -
RF_C Ratio compensation factor phase C VCap*RF_C=VBus_C - 0.000 3.000 0.001 - -
59THD 95% and 100% Stator earthground fault protection based on 3rd harmonic
GenRatedVolt Generator rated (nominal) phase-to-phase voltage in kV kV 1.0 100.0 0.1 - 12.5 - 12.5
NoVoltage
ResidualVoltage
TVoltType Used connection type for gen. terminal voltage transformer - AllThreePhases - -
(TVoltType) PhaseA
PhaseB
PhaseC
Disabled
Operation Disable/Enable Operation - - -
Enabled
Beta Portion of voltN3rdHarmonic used as bias kV 1.00 10.00 0.01 - -
No
Cbexists Defines if generator CBexists (between Gen & Transformer) - - -
Yes
FactorCBopen Beta is multiplied by this factor when CB is open - 1.00 10.00 0.01 - -
VN3rdHPU Pickup 3rd Harm V< protection (when activated) % of VB/1,732 % 0.5 10.0 0.1 - -
VT3BlkLevel If VT3 is below limit 3rdH Diff is blocked, in % of VB/ 1,732 % 0.1 10.0 0.1 - -
VNFundPU Pickup fundamental VN> protection (95% SEF), % of VB/1,732 % 1.0 50.0 0.1 - -
t3rdH Operation delay of 3rd harm-based protection (100% SEF) s 0.020 60.000 0.001 - -
tVNFund Operation delay of fundamental VN> protection (95% SEF) s 0.000 60.000 0.001 - -
FREQUENCY PROTECTION
81 Underfrequency protection (PTUF)
TUF1
Operation Disable/Enable Operation - Off / On ON - ON -
380200604.xls 02/28/2018 2 de 3
BASE DE DATOS DE AJUSTE DE PROTECCIONES
Tipo: PROTECCION GENERADOR Tipo Central: HIDROELECTRICA Región: ZONA SUR
Fabricante: ABB C.H.: CHARCANI I Dpto:
Modelo: REG670 Tensión Nom.: 4,16 kV Empresa:
Versión: Grupo Gen.: G1-G2 Diag.Unif.N°:
N° Serie: Uprim[kV]: 4.16kV Man.Serv.N°:
Tecnología: NUMÉRICA Fases: RSTN Fecha: 13-Feb-14
Año instal.: Ucc [V]: Respons.: K.V.H.
Código: Uca [V]: 100 Revisión: 0
Ubic.Tabl: Ica [A]: 5
Sistema: PRINCIPAL Frec.[Hz]: 60
DESCRIPCION DE LOS AJUSTES GRUPO 1 (AS BUILT) GRUPO 1 (AECP 2014) OBSERVACIONES
ACTUAL PROPUESTO
ANSI COD DESCRIPCION UNIDAD MIN MAX PASO SECUNDARIO PRIMARIO SECUNDARIO PRIMARIO
t_MaxTripDelay Maximum time operation limit for voltage based timer. (tMax) s 0.010 60.000 0.001 1.00 - 1.00 -
t_MinTripDelay Minimum time operation limit for voltage based timer. (tMin) s 0.010 60.000 0.001 1.00 - 1.00 -
TUF2
Operation Disable/Enable Operation - Off / On OFF - OFF -
380200604.xls 02/28/2018 3 de 3