- DocumentoNATE Module 1_Week1cargado porParag Naik
- DocumentoFrequently Asked Questions and Answers Emc 2017-Updatedcargado porParag Naik
- Documentopuzyrewski2003cargado porParag Naik
- Documentoarticle1380788838_Ali et al.pdfcargado porParag Naik
- Documento17-4-phcargado porParag Naik
- DocumentoF02_3cargado porParag Naik
- DocumentoA Look at Compressor Impeller Technologies for Turbochargers Focusingon Surge Mitigation 2229 8711 1000185cargado porParag Naik
- Documento223cargado porParag Naik
- DocumentoAreas of Specializations 090418cargado porParag Naik
- DocumentoCommand Stylecargado porParag Naik
- DocumentoAssess Score Evaluatecargado porParag Naik
- Documento10 Evidence Based Principles of Effective Teaching Rsearchcargado porParag Naik
- DocumentoAnalysis of a Shrink-fit Failure on a Gear Hub Shaft Assemblycargado porParag Naik
- Documento9979726-Vibrations-of-Shells-and-Plates.pdfcargado porParag Naik
- DocumentoOlofsson_2015_IOP_Conf._Ser.%3A_Mater._Sci._Eng._84_012026 (1)cargado porParag Naik
- Documentogao2006_2.pdfcargado porParag Naik
- DocumentoCoupled Vibration and Naturalcargado porParag Naik
- DocumentoCampbell Diagram Chart Results.docxcargado porParag Naik
- DocumentoCampbell Diagram Chart Results.docxcargado porParag Naik
- DocumentoStudy on Damping Control for Vibration Isolation Andcargado porParag Naik
- DocumentoIJSETR-VOL-3-ISSUE-1-100-106.pdfcargado porParag Naik
- Documento01FE16MMD011_Paragpushp Naik_FEMD assignment.xlsxcargado porParag Naik
- DocumentoVibration assignment_01F16MMD011_Naik Paragpushp.docxcargado porParag Naik
- DocumentoVibration assignment_01F16MMD011_Naik Paragpushp.docxcargado porParag Naik
- DocumentoA THERMOELASTIC ANALYSIS of SHRINK-FIT TYPE Constructions by Boundaary Element Methodcargado porParag Naik
- Documentospr Technical Information 4.pdfcargado porParag Naik
- DocumentoMechanical Drawing Standards and Tables.pdfcargado porParag Naik
- DocumentoContact Problem of Disk on Shaft Fixed by Induction Shrink Fit.pdfcargado porParag Naik
- DocumentoAnalysis of Elastic-plastic Interference-fit Jointscargado porParag Naik
- Documentoekhteraeitoussi2012cargado porParag Naik
- DocumentoIMECS2016_pp694-698cargado porParag Naik
- DocumentoModeling Component Assembly of a Bearing Using Abaqus.pdfcargado porParag Naik
- Documento14. Separation Frequency Analysis of Interference Fitted Hollow Shaft–Hub Connections by Finite Element Methodcargado porParag Naik
- DocumentoOn Shrink Fit Analysis and Designcargado porParag Naik
- DocumentoModeling Component Assembly of a Bearing Using Abaquscargado porParag Naik
- Documento19. Autofrettage of thick cylinders.pdfcargado porParag Naik
- Documento9.A general autofrettage model of a thick-walled.pdfcargado porParag Naik
- Documento9.a General Autofrettage Model of a Thick-walledcargado porParag Naik
- Documento12. Autofrettage process analysis of a compound cylinder based on the elastic-perfectly.pdfcargado porParag Naik
- Documento12. Autofrettage Process Analysis of a Compound Cylinder Based on the Elastic-perfectlycargado porParag Naik
- Documento18. Determination of Residual Stress Distributions Incargado porParag Naik
- Documento2. Simulation of Removing Autofrettage-Induced Residualcargado porParag Naik
- Documento1.Optimum autofrettage pressure in thick cylinders.pdfcargado porParag Naik
- Documento11. Residual Stress Analysis of an Autofrettagedcargado porParag Naik
- Documento10. Actual Unloading Behavior and Its.pdfcargado porParag Naik
- DocumentoDesign and Analysis on Interference Fit in the Hardwood Dowelglued.pdfcargado porParag Naik
- DocumentoContact Problem of Disk on Shaft Fixed by Induction Shrink Fit.pdfcargado porParag Naik
- Documento[3] Stress analysis of shrink-fitted joints for various fit forms via finite element method.pdfcargado porParag Naik
- Documento[7] Finite Element Analysis of Optimized Compound Cylindercargado porParag Naik