Está en la página 1de 22

1.Refer to the exhibit. Computer A sends a broadcast message. Which devices will see the broadcast?

computer B computer B and Router1 computer C and Router1 computer B, computer D, computer E and Router1 computer B, computer C, computer D, computer E and Router1 computer A, computer B, computer C, computer D, computer E and Router1 2.Which parameter is used to uniquely identify one wireless network from another? SSID OFDM WEP DSSS 3.Refer to the exhibit. What will allow a host on VLAN 40 on switch X to communicate with a host in VLAN 40 on switch Y? QoS routing trunking VPN 4.Which two statements describe Spanning Tree Protocol? (Choose two.) It eliminates Layer 2 loops in network topologies. It eliminates the need for redundant physical paths in network topologies. It can only be used in networks in which Layer 2 switching is in use. It can only be used in networks where both routers and switches are used together. It can only be used in networks where routers are installed. 5.Refer to the exhibit. A new host needs to be connected to VLAN 1. Which IP addresses should be assigned to this new host? 192.168.1.11 /28 192.168.1.22 /28 192.168.1.33 /28 192.168.1.44 /28 192.168.1.55 /28 6.Refer to the exhibit. The network administrator enters the configuration shown to allow both SSH and Telnet connections to the switch. The Telnet connections

fail. What is the most likely cause of this problem? The SSH version number is wrong. SSH has been configured on the wrong line. Telnet and SSH cannot be configured simultaneously. The transport input command is configured incorrectly. 7. Which three statements are regarding router-on-a-stick inter-VLAN routing? (Choose three.) requires the use of subinterfaces on the router requires an access link between the router and Layer 2 switch more cost-efficient and scalable than using multiple physical interfaces requires each subinterface to be configured with the no shutdown command can impact performance if many VLANs compete for bandwidth on a single router interface makes troubleshooting the inter-VLAN routing configuration much less complex than when using multiple physical interfaces 8. What are three benefits of a hierarchical network model? (Choose three.) reduced contention for bandwidth reduced size of the physical layout increased fault tolerance of the network elimination of the need for wiring closets elimination of the need for layer three functionality simplification of management and troubleshooting 9.Refer to the exhibit. Which three options correctly identify information that could be associated with this output?(Choose three.) Interface FastEthernet3/0/0 is subinterfaced. A non-proprietary trunking protocol is in use. The configuration is appropriate for a router-on-a-stick network design. A shutdown command has been applied to interface FastEthernet3/0/0. Interface FastEthernet3/0/0.3 is mapped to the default management VLAN. An IP address should be applied to FastEthernet3/0/0 for correct data routing. 10.Refer to the exhibit. Switch SW2 was tested in a lab environment and then inserted into a production network without reloading its configuration. After the trunk link between SW1 and SW2 was brought up, all users lost connectivity to the network. What could be the source of the problem? All the VLANs were pruned from the trunk port between SW1 and SW2. SW1 and SW2 cannot be both set as VTP servers in the same VTP domain.

VTP configuration revision number of SW2 was higher than the configuration revision number of SW1. The additional VLANs from SW2 created more VLANs than the VLAN database of SW1 could contain. 11. Which three statements are correct concerning the default configuration of a new switch? (Choose three.) Spanning Tree Protocol is disabled. Enable password is configured as cisco. All switch ports are assigned to VLAN1. The flash directory contains the IOS image. VLAN1 is configured with a management IP address. All interfaces are set to auto-negotiation of speed and duplex. 12.Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same time. How do the hosts respond on the network? (Choose two.) After the end of the jam signal, a backoff algorithm is invoked. Hosts 1 and 4 are operating full duplex so no collision will exist. The hub will block the port connected to Host 4 to prevent a collision. Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media. If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle before transmitting. 13.Refer to the exhibit. After the listed commands are entered into router R1 and switch S1, the administrator enters the show interface fa0/1 trunk and gets the results shown. What is the likely problem? The trunk is established, but no VLANs have been configured to use it. The trunk has not been established because the router does not support dynamic trunking protocol. The router, the switch, or both must be configured with the dynamic desirable option for dynamic trunking protocol to establish a trunk. The router is missing the dynamic trunking protocol statements necessary to form a trunk. 14.What three tasks should be performed before moving a Catalyst switch to another VTP management domain? (Choose three.) Select the correct VTP mode and version. Configure the switch with the name of the new management domain.

Download the VTP database from the VTP server in the new domain. Configure the VTP server in the new domain to recognize the BID of the switch. Reset the VTP counters to allow the switch to synchronize with the other switches in the new domain. Verify that the switch has a lower configuration revision number than the other switches in the new domain. 15.Refer to the exhibit. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. Which hosts will receive the collision jamming signal? only hosts A and B only hosts A, B, and C only hosts A, B, C, and D only hosts A, B, C, and E 16. Which statement regarding the service password-encryption command is ? The service password-encryption command is entered at the privileged EXEC mode prompt. The service password-encryption command encrypts only passwords for the console and VTY ports. The service password-encryption command encrypts all previously unencrypted passwords in the running configuration. To see the passwords encrypted by the service password-encryption command, enter the no service password-encryption command. 17.Refer to the exhibit. Which two statements are regarding what the cost value of 23 represents for Switch4? (Choose two.) This cost represents the lowest cost path for Switch4 to the root switch. A cost of 23 is the value being advertised out port 16 on the switch upstream (closer) to the root switch. Switch4 adds the cost of a Fast Ethernet link to 23 to determine its total cost to reach the root switch. Switch4 is connected via a Fast Ethernet link to an upstream switch that in turn is directly connected to the root switch via a Gigabit Ethernet link. The root switch is advertising a cost of 23, which is lower than any other switch in the VLAN0001 spanning-tree domain. 18.Refer to the exhibit. What three statements describe why Host1 and Host2 are unable to communicate? (Choose three.) The switch ports are on different VLANs.

The switch IP address is on the wrong subnet. The hosts are configured on different logical networks. A router is required to forward traffic between Host1 and Host2. The VLAN port assignments must be contiguous for each VLAN. The host default gateway addresses must be on the same logical network. 19.Refer to the exhibit. Each switch is shown with its MAC address. Which switch will be elected as the spanning-tree root bridge if the switches are configured with their default priority values? switch A switch B switch C switch D switch E switch F (11.11.11.11.11.11) 20. Why is it important that the network administrator consider the spanning-tree network diameter when choosing the root bridge? The network diameter limitation is 9. BPDUs may be discarded because of expiring timers. The cabling distance between the switches is 100 meters. The network diameter must be set to the number of meters of the cable between the root bridge and its farthest connected switch. 21.What is the purpose of issuing the command switchport mode access on a switch interface? disable port security make the port operational override the default port behavior force the port to be a part of a single vlan 22. Which identifier is used to keep track of frames that are destined for a particular wireless client? AID SSID BSSID ESSID 23.Refer to the exhibit. What will happen when frames that contain an unknown source address reach interface fa0/24? A syslog message will be logged.

Fa0/24 will become error-disabled. The incoming frames will be dropped. The security violation count will be incremented. 24. In which mode is a VTP switch operating if it has been configured to only forward VTP advertisements? client root server transparent 25.Which method establishes an administrative connection for configuring the Linksys WRT300N wireless access point? Associate with the access point and then open a HyperTerminal session with the access point. Physically connect to the access point and then reboot the computer to launch the configuration software. From a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser. Modify the TCP/IP properties of the computer connected to the access point so that it exists on the same network, and then reboot your computer to establish a connection. 26. What two methods can be used to remove MAC address table entries from a switch? (Choose two.) Power cycle the switch to clear all dynamically learned addresses The clear switching-tables command will remove statically configured entries. The clear mac-address-table command will remove statically and dynamically configured table entries. The erase flash command will clear all statically configured table entries. Statically configured MAC addresses will automatically be removed from the address table 300 minutes after the last activity on a switch port. 27. What are two benefits of the IEEE 802.11n standard over the IEEE 802.11G? (Choose two.) requires less equipment provides improved range permits increased data rates has a single-input and a single-output needs no hardware upgrade for compatibility

28.How are data frames identified and sent to the correct VLANwhen existing an Ethernet trunk? frames are forwarded to the correct VLAN based on the VLAN tag frames are always forwarded to the native VLAN when exitsting a trunk frames are forwarded to the correct VLAN based on the source IP address frames are forwarded to the correct VLAN based on information in the MAC address tables 29. Which STP port type can only appear once on a segment, and must be present in order for traffic to flow on that segment? non-root port disabled port designated port non-designated port 30.After receiving a console notification on Switch2, the network administrator begins to troubleshoot the trunk link between Switch1 and Switch2. Which configuration change can be made to correct the problem with the trunk link? Set the Fa0/1 interface on Switch2 to trunk mode. Change the trunk encapsulation on Switch2 Fa0/1 to dot1q. Change the native VLAN on Switch2 interface Fa0/1 to VLAN 100. Change the access mode VLAN on Switch2 to the default VLAN 1 31.What will be the effect of the command S1#copy system:running-config tftp://172.16.2.155/tokyo-config? The IOS will be copied to the TFTP server. The configuration file named tokyo-config will overwrite the startup configuration file on S1. The running configuration file on S1 will be saved via TFTP to a file named tokyoconfig. The contents of NVRAM on S1 will become the startup configuration file on the tokyo switch.

32.Refer to the exhibit. What is true of the configuration of switch S1? A Cisco proprietary protocol is in use for ports Fa0/1 and Fa0/3. Switch ports Fa0/1 and Fa0/3 have been configured with the switchport mode access command. Untagged frames received on ports Fa0/1 and Fa0/3 will be placed on VLAN 1. Switch ports Fa0/1 and Fa0/3 are configured to carry data from multiple VLANs. 33.What advantage does WPA2 offer over WPA? SSID cloaking MAC address filtering Layer 2 payload encryption authentication through RADIUS 34.Which two statements describe Spanning Tree Protocol? (Choose two.) It is only used at Layer 2. It is configured on routers. It eliminates Layer 2 loops in network topologies. It limits the number of valid MAC addresses allowed on a port. It allows VLAN information to propagate to other switches in the network 35. Which two statements about a service set identifier (SSID) are true? (Choose two.) provides strong wireless security responsible for determining the signal strength tells a wireless device to which WLAN it belongs used to encrypt data sent across the wireless network all wireless devices on the same WLAN must have the same SSID

36.After unpacking a new Linksys WRT300N wireless multifunction device, a user needs to change the default administrator password andmake other configuration changes. What must the user do to access the device in order to make these changes? Use a wireless client to associate with the WRT300N and then open a HyperTerminal session with the device. Establish a wired connection with the device and then reboot the attached computer to launch the configuration software. Establish a wired connection from a computer in the same IP subnet as the WRT300N and enter the default IP address of the deviceinto a web browser on the computer. Modify the TCP/IP properties of the computer that is connected to the WRT300N so that the computer and the WRT300N exist onthe same network. Then reboot the computer to establish a connection 37.Which statement correctly describes a function of a Layer 2 switch? It routes packets between different LAN segments. It uses the destination MAC address to selectively forward a frame. It performs switching and filtering based on the destination network layer address. It drops a frame whose destination MAC address is not in the MAC address table 38.Refer to the exhibit.After the listed commands are entered into router R1 and switch SW1,PC1 and PC2 cannot ping each other.The network administrator enters the #show interface trunk command and gets the results that are shown .What is the likely problem? the router has not been configured with a routing protocol the trunk established ,but no VLANs have been configured to use it the trunk has not been established because the switch port not been configured for trunking

the switch ,the router ,or both must be configured with the dynamic desirable option for the Dynamic Protocol to establish a trunk 39.Refer to the exhibit. A wireless infrastructure has been established in a company building as shown. The design goal was to allow roaming between the three APs for handheld devices.However, the devices lose connectivity when the users roam. How can this problem be fixed? Assign different SSIDs to each AP. Reconfigure all APs to the same channel. Use the same BSSID address for each AP. Reposition the APs so that each area of signal strength overlaps the neighbor by at least by at least 10-15% 40. Refer to the exhibit. What will happen when frames with a source address other than 0019.d2e4.d9f7 enters interface Fa0/24? Fa0/24 will become error-disabled. The incoming frames will be dropped. The Fa0/24 port LED will be turned off. The security violation count will be incremented 41.Which type of frame contains information that is used in the election of the spanning tree root bridge? BID LSA LSU BPDU 42.Which three statements accurately describe VLAN types? (Choose three). A management VLAN is any VLAN that is configured to access management features of the switch. A data VLAN is used to carry VLAN management data and user-generated traffic. After the initial boot of an unconfigured switch, all ports are members of the default VLAN.

An 802.1Q trunk port, with a native VLAN assigned, supports both tagged and untagged traffic. Voice VLANs are used to support user phone and e-mail traffic on a network. VLAN 1 is always used as the management VLAN 43.S2#conf t S2(config)#enable password cisco1 S2(config)#enable secret password cisco2 S2(config)#line vty 0 5 S2(config-line)#password cisco S2(config-line)#login S2(config-line)#line console 0 S2(config-line)#password cisco3 S2(config-line)#login S2(config-line)#end Refer to the exhibit .Which password allow the administrator to eneter the privileged exec mode? cisco1 cisco2 cisco3 cisco 44.Refer to the exhibit. Switches SW3 and SW4 are brand new switches with default configurations.The links between the switches are configured as trunk links

and all VLANs are allowed on thetrunks. On the basis of the show running-config output that is provided, which VLANs will beavailable on SW3 and SW4? SW3-VLAN 10,20 SW4-VLAN 10,20 SW3-VLAN 10,20,100 SW4-VLAN 10,20,100 SW3-VLAN 10,20,100 SW4-VLAN 10,20,40,50,100 SW3-VLAN 10,20,40,50,100 SW4-VLAN 10,20,40,50,100 45.What is a possible impact of setting too short an aging time in the MAC address table of a switch? overly large address table unnecessary flooding of packets excessive timeouts of static addresses impaired ability to dynamically learn new addresses 46.Which configuration changes will increment the configuration revision number on theVTP server? configuring trunk links on the VTP server configuring or changing the VTP password configuring or changing the VTP domain name configuring or changing the VTP version number configuring or deleting a VLAN or creating a VLAN name 47.What provides an authentication mechanism for 802.11-based wireless networks? DSSS OFDM SSID

WPA 48.When a unicast frame is received on a switch with STP disabled and an empty MAC address table, how will the switch handle the frame? The switch will drop it. It will send it out every port. It will send out an ARP request. It will send it out every port except the one on which the frame was received. 49.Which statement correctly describes the spanning-tree path cost? It is calculated based on the total number of switches connected in a loop. It is calculated based on the utilization of all the switches along a given path. It is calculated based on the bridge priority of the switches along a given path. It is calculated based on the sum of the port cost value, determined by link speed, for each switch port along a given path 50.STA-1(config)#interface fa0/10 STA-1(config-if) #switchport mode access STA-1(config-if) #switchport access vlan 30 STA-1(config-if) #end Refer to the exhibit. What is the purpose of the configuration commands that are shown? to activate port Fa0/10 to make the port a member of VLAN 30 to activate port security on port Fa0/10 to add VLAN 30 to the trunk that is connected to port Fa0/10 51.Refer to the exhibit. Hosts B and C attempt to transmit a frame at the same time, but a collision occurs. Which hosts will receive the collision jamming signal? all hosts that are shown

only hosts B and C only hosts A, B, and C only hosts A, B, C, and D only hosts A, D, E, and F only hosts D, E, and F 52.Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the Network Mode option Mixed mean? the router supports encryption and authentication the router supports both wired and wireless connection the router supports 802.11b,802.11g and 802.11n devices the router supports connectivity through infrared and radio frequencies 53.Which switching method provides error-free data transmission? fragment-free fast-forward integrity-checking store-and-forward 54.A network administrator is implementing a Layer 2 solution for a legacy network that uses a combination of switches. Many of the older devices support only ISL trunking while others support both ISL and 802.1Q trunking.Witch variant would be best suited for this network? RSTP MSTP PVST PVST+

55.Refer to the exhibit. The network administrator is planning five additional VLANs to be shared throughout the VTP domain on S3. What action should the administrator take before creating the additional VLANs? Create the VLANs on a switch in VTP server mode and allow them to propogate to the other switches in the domain. Modify the configuration revision to 10 to support the additional VLANs. Enable the VTP pruning mode in order to create the VLANs on S3. Enable the VTP v2 mode. 56. Refer to the exhibit.Why must the NIC of Host1 operate in half-duplex mode? H1 must be able to detect collisions all other hosts have been configured for half-duplex the collision detect circuit on Switch1 has been disabled port FA0/1 on Switch1 has been configured for half-duplex

57.Refer to the exhibit. The switches are configured for VTP as shown. Which two
statements correctly describe the operation of these switches? (Choose two.) A new VLAN can be added to Switch1 and that information will be added only to Switch2. A new VLAN can be added to Switch1 and that information will be added to Switch2 and Switch4. An existing VLAN can be deleted from Switch4 and that VLAN will be deleted from Switch1 and Switch2. An existing VLAN can be deleted from Switch2 and that VLAN will be deleted from Switch1 and Switch4. A new VLAN can be added to Switch4 and that information will be added to Switch1, Switch2, and Switch3. A new VLAN can be added to Switch3 and that information will be added to Switch1, Switch2, and Switch4.

58.Which layers should support QoS in a hierarchical network? only the acces layer only the distribution and core layers only the acces and distribution layers the access,distribution and core layers 59.Refer to the exhibit. The configuration steps that are listed in the exhibit have been entered in switch S1 via the console. Subsequent attempts to telnet to the switch are not successful. What is causing the problem? The switch must be configured with SSH version 1. The transport input command must specify Telnet access. The RSA keys must be returned to zero before SSH will permit Telnet access. The ip domain-name command must also be entered in line configuration mode for the vty lines. 60.Refer to the exhibit. Switch SW2 was tested in a lab environment and then inserted into a productionnetwork without reloading its configuration. After the trunk link between SW1 and SW2 was broughtup, all users lost connectivity to the network. What could be the source of the problem? All the VLANs were pruned from the trunk port between SW1 and SW2.SW1 and SW2 cannot be both set as VTP servers in the same VTP domain. VTP configuration revision number of SW2 was higher than the configuration revision number of SW1. The additional VLANs from SW2 created more VLANs than the VLAN database of SW1 could contain SW1 and SW2 cannot be both set as VTP servers in the same VTP domain 61.Which statement accurately describes routing between VLANs when default gateway addresses of the VLANs are applied to physical interface ? there is no bandwidth contention on the router interface this solution will be less expensive thatn if subinterface are used

trunking will be established between the router and switch ports only one physical router interface will be required for multiple VLANs 62.A network technician notes that ports Fa0/9 through Fa0/12 on a switch have been assigned to VLAN 40. VLAN 40,however, was improperly named and the technician deletes it. What happens to the ports that were assigned to VLAN? All ports will automatically become members of VLAN 1. The ports will automatically become members of the native VLAN. All VLAN 40 member ports will be unable to communicate with any other stations. All ports will remain assigned to VLAN 40 because it cannot be deleted if any ports are currently assigned to it 63. Which device must be installed in each computer to allow a wireless connection to be established? DSL modem wireless NIC wireless router wireless access point 64.When implementing a router on a stick what must be configured on the router to ensure connectivity between different VLANs? subinterfaces routing protocol switched virtual circuits dynamic trunking protocol 65.S1(config)# line vty 0 4 S1(config-line)#password cisco S1(config-line)#login

Refer the exhibit.What is the result of issuing these commands? the enable password will be set the password will be set for the first Telnet connection the password will be set for the console connection the password will be set for the auxiliary connection 66.In the implementation of PVST+ in a specific VLAN where all switches have default spanning tree priorities ,which spanning-tree command setting could be assigned to force one of the Catalyst switches to become and remain the root bridge? root primary priority 8192 priority 2048 spanning-tree mode rapid PVST 67. Refer to the exhibit. Host A is sending a frame to host C. How does switch SWA tag the frame? It tags the frame with VLAN 1 and sends it to host C. It tags the frame with VLAN 10 and sends it to host C. It tags the frame with VLAN 99 and sends it to host C. It does not tag the frame and sends it to host C 68. Which benefit is gained by designing a network with a small diameter? lower latency improved security increased redudancy higher interface bandwidth

69.A wireless client is attempting to establish a connection with a wireless access point. What process does the client use to discover the access points which are available to it? probing beaconing association authentication 70.What is a function or characteristic of the native VLAN? It is the VLAN that supports untagged traffic on an 802.1Q trunk. It is always assigned to VLAN 1 for backward compatibility. It is always the same VLAN number for all trunks within an organization. It is used as the management VLAN throughout the entire switched network. 71.Which combination is required to establish a connection to initially configure the Linksys WRT300N wireless access device? a computer with a console connection to the WRT300N a computer with a wireless connection to the WRT300N a computer with an AUX port connection to the WRT300N a computer configured in the same IP subnet as the WRT300N and a direct cable connection to it 72.Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same time. How do the hosts respond on the network? (Choose two.) After the end of the jam signal, a backoff algorithm is invoked. Hosts 1 and 4 are operating full duplex so no collision will exist. The hub will block the port connected to Host 4 to prevent a collision.

Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media. If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle before transmitting 73.An administrator is troubleshooting a PC on the network which is suffering from slow and intermittent connectivity. The PC has a ping success rate to the default gateway of less than half the ping attempts. Other PCs on the switch can consistently ping the default gateway. The switch port is configured for auto duplex and the PC is configured for full duplex. What will commonly cause this problem? The PC is set to full duplex. The switch port fails to autonegotiate the duplex setting and defaults to half duplex, which causes a duplex mismatch. The switch traffic is exceeding available frame buffers. The result is that frames are being dropped. The PC and the default gateway have different bandwidth Ethernet ports. The default gateway is not on the same switch that the PC is. If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle before transmitting. 74.Refer to the exhibit. What does the term DYNAMIC indicate in the output that is shown? This entry can only be removed from the MAC address table by a network administrator. When forwarding a frame to the device with address 0060.5c5b.cd23, the switch does not have to perform a lookup to determine the final destination port. Only the device with MAC address 0060.5c5b.cd23 will be allowed to connect to port Fa0/18. The switch learned this MAC address from the source address in a frame received on Fa0/18.

75.Refer to the exhibit. The configuration steps that are listed in the exhibit have been entered in switch S1 via the console. Subsequent attempts to telnet to the switch are not successful. What is causing the problem? The switch must be configured with SSH version 1. The transport input command must specify Telnet access. The RSA keys must be returned to zero before SSH will permit Telnet access. The ip domain-name command must also be entered in line configuration mode for the vty lines. 76.Why is MAC address filtering considered a poor choice in securing a WLAN? Available bandwidth is reduced. MAC addresses are easily spoofed. APs are more susceptible to DoS attacks. The payload encryption is easily broken. 77.Which two statements describe the operation of an access layer Ethernet switch? (Choose two.) Broadcasts are natively blocked by the switch. Subnetting is used by the switch to segment local networks. Frames that contain an unknown destination MAC address are dropped by the switch. The source MAC address within a frame is used by the switch to associate a port with that MAC address. Frames are directed by the switch from one port to another based on the destination MAC address within the frame. Data packets are forwarded by the switch from one port to another based on the destination IP address within the packet. 78.What is the purpose of the switch command switchport access vlan 99? to enable port security

to make the port operational to assign the port to a particular VLAN to designate the VLAN that does not get tagged to assign the port to the native VLAN (VLAN 99) 79. A network administrator issued the erase nvram: command on a switch. What will be the outcome of the command? It will clear the contents of the MAC table. It will clear the contents of the VLAN database. It will clear the contents of the startup configuration file. It will clear the contents of the running configuration file. 80.What type of message do wireless clients transmit when they are searching for a specific wireless network? probe beacon associate authenticate

También podría gustarte