Está en la página 1de 4

Catalogue page Part no.

:
Page:1

186285

Push-in/threaded L-fitting, rotational QSRL-G1/8-4


Quick Star
for plastic tubing PAN, PUN, with G male thread and sealing ring, with ball bearing, rotatable 360. The Quick Star connector series offers a reliable solution for every connection. The stainless steel retaining ring inside the fitting holds the tubing securely without damaging its surface. Vibration and pressure surges are safely absorbed. The tubing can be detached easily by pressing down the blue release ring. For your convenience, the appropriate outside tubing diameter is marked on the release ring. An NBR rubber sealing ring guarantees a perfect seal between standard OD tubing and the body of the fitting. Standard tubing is suitable for use with compressed air and vacuum. All of the brass components included with Festos push-in fittings are nickel plated, and are thus highly resistant to corrosion. Mini series Specially adapted accessories for Festos miniature pneumatics series Tubing ODs of 3, 4 and 6 mm, as well as M3, M5, M7, R1/8 and G1/8 connecting threads are included in the mini-series. Standard series A large selection of push-in fittings for tubing ODs of 4, 6, 8, 10, 12 and 16 mm and connecting threads from R1/8 to R1/2, and G1/8 to G1/2. Special series :- Flame retardant per UL 94 V0 - Corrosion and acid resistant t- Temperature range to max. 150 C with excellent corrosion protection - Antistatic - Tool for removing QS push-in fittings Three thread types are available :Metric thread - With sealing ring R thread

Printed:10.10.2002 09:30:14

Festo AG & Co. Postbox 73734 Esslingen

Catalogue page Part no.:


Page:2

186285

In accordance with DIN 2999-1 and ISO 7/1 - Sealing by means of Teflon coating on the threads - No additional sealing surface required - Self-sealing threads - Small outside diameter - Small width across flats - Simply screw in by hand, and then tighten with one or two turns of an open end wrench. - The fitting can be reinstalled up to five times. G thread In accordance with DIN ISO 228-1 - With sealing ring - The sealing ring better compensates for thread tolerances. - Shorter thread - Uniform installation depth - Interchangeable sealing ring - Sealing outside of the thread with captive sealing ring at front made of PBT - All internal threads from G1/8 to G1/2 are incompliance with DIN ISO 228-1. Several Quick Star push-in fittings can also be installed with an Allen key. Make sure that the Allen key is not inserted too far into the fittings to prevent the risk of damage to components behind the fitting. Note Interference may be caused at function fittings when screwed too far into connection threads. The insertion depth and the recommended tightening torque must be observed. Damage may otherwise occur if the recommended tightening torque is exceeded by more than 50%. Barbed fitting series These connectors make tubing connection easier, especially for mounting to control cabinets, for mounting frames and for the M5 compact system. - With barbed fitting - For standard ID compressed air tubing - For 2, 3, 4 and 6 mm tubing IDs - M3 and M5 metric thread - G1/8, G1/4 and G3/8 G thread - Corrosion and acid-resistant variants

Printed:10.10.2002 09:30:14

Festo AG & Co. Postbox 73734 Esslingen

Catalogue page Part no.:


Page:3

186285

Accessories Connecting pliers ZMS Disconnecting pliers ZDS

Printed:10.10.2002 09:30:14

Festo AG & Co. Postbox 73734 Esslingen

QSRL-G1/8-4
Push-in/threaded L-fitting, rotational

Data sheet
Part no.: 186285 Page:1

Feature Nominal size connector Nominal size of tubing connection 1 Mounting/connection thread Operating pressure min. Operating pressure max. Minimum ambient temperature Maximum ambient temperature Minimum meduim temperature Maximum meduim temperature Material of housing Medium

Data/description 2,6 mm 4 G 1/8 -0,95 bar 10 bar 0 C 60 C 0 C 60 C PBT-reinforced Compressed air, filtered

Printed:10.10.2002 09:30:29

Festo AG & Co. Postbox 73734 Esslingen

También podría gustarte