Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Service Training
2008
TS-08051301-T
Hello and Welcome to JVCs LCD Panel Troubleshooting Guide. This guide is intended to help you assess problems related to the LCD Panel Electronic Boards. This also serves as a guide to discovering the failures of the TV Electronic Boards as well.
Before you begin any troubleshooting, review the TV Models Service Manual and Service Bulletins. These items may show information relevant to the repair.
Also, if at any time you have difficulty proceeding with steps or questions regarding the repair, contact JVC Tech Support or you Local JVC Field Engineer for assistance.
COURSE OVERVIEW
This presentation will cover items that will assist in the Troubleshooting of faults related to the LCD panel and it's PWBs and components.
SERVICE INFORMATION
Model Identification
Prior to service, it is always wise to verify the Model and Version to ensure that the correct Service manuals and Schematics are being used. The pictures show the LT-32E478 Versions SAA and VAA. One of the differences in the (2) models is the LCD Panel used in the TV. There are other differences between the models that were not explained. Version differences may include LCD Panel, PWB or Circuit Design differences. The Model Number listed at the top of the model label will always be the same for all versions. To find the Model Version it is necessary to look to the right of the Model Number. This may vary at times, but will always be shown in the Service Manual.
1. Control PWB inputs LVDS signal from the TVs Video PWBs and outputs Drive Signals to the LCD Panel 2. LCD Panel Horizontal Gate and Vertical Source Drives on the LCD Panel create the displayed video image 3. Inverter PWBs Power the Backlight. LCD Panel Assemblies may have (x1) or (x2) Inverter PWBs. 4. Backlight Provides light and allows the LCD Panel image to be seen by the viewer.
1. Control PWB inputs LVDS signal from the TVs Video PWBs and outputs Drive Signals to the LCD Panel. 2. LCD Panel Horizontal Gate and Vertical Source Drives on the LCD Panel create the displayed video image. Failures of these drivers will result in the Vertical and Horizontal line and Bar failures that are often seen with LCD TVs. 3. Inverter PWBs These convert the low voltage DC to High Output AC to power the Backlights. LCD Panel Assemblies may have (x1) or (x2) Inverter PWBs. Failure of (x1) Inverter PWB may result in partial or complete failure of the backlights. 4. Backlight Provides light and allows the LCD Panel image to be seen by the viewer.
Backlight
LCD Panel
This slide depicts the components of the LCD Panel to show their construction.
Removal of the metal frame of the LCD allows easy removal of the LCD Panel (LCD Cell and Drive PWBs).
Control PWB
These signals may run directly to the Inverter PWB in some cases
Inverter Board To light the backlight, input DC from the TV Power Supply is stepped up to a High Voltage AC(AC950V for example). The Backlight Control Signals may be processed at the Control PWB in some cases. In other cases, these signals flow directly from the TVs Digital Signal PWB to the Inverter.
TV Power supply
The LCD Panel usually includes two electronic boards. The Control Board and the Inverter Board.
The Control Boards primary function is to provide the data that drives the LCD panels Gate-ICs. The inputted LVDS signal from the TVs Video Circuits is converted and read into the Frame Memory of the Control Board. The data that drives the LCD panel transistors is read from the frame memory and transferred to the Gate-IC in the LCD Panel. These Gate ICs drive the video lines of the LCD Panel.
The Inverter Board converts the small DC voltage from the TV power supply to the High Voltage AC that is required to power the LCD Panels backlight.
Backlight Control signal are used to control the ON/OFF and brightness of the backlightThis signal is usually created on the TVs Digital Signal Board and passes to the Inverter. In some instances, the signal passes to the LCD Panel Control Board prior to reaching the inverter.
BLOCK DIAGRAMS
LCD Panel
Power Supply PWB
T9501 CN10A CN00A 24VDC 24VDC 5VDC CN00Q 24VDC CN00P 24VDC CN0DC LCD Power CN00H
DC to DC PWB
LCD Panel
IC9602
Backlight
(x20) total Backlights
Backlight
Analog PWB
IC6001 CN001 B1_Power
IC7033
CN00W
BL_ON
DC_DIM
CN001
PWM_DIM
CN0LV1
5/12VDC
Based on LT-37X787/Z
Here we show the Signal flow from the TVs PWBs to the LCD Panels Circuit Boards. This Signal and Power flow may vary between TVs and LCD panels, but the general signals utilized will always be the same. When troubleshooting Backlight problems, always trace the Backlight Control Signal Path from Board to Board to ensure the signal is being passed from the Source to the Intended Point. Some LCD TVs will utilize a Master/Slave combination of Inverter Boards to power the LCD Panel Backlight. The Master Inverter may power half or the majority of the LCD Panel Lamps while the Slave Inverter will power the remaining Lamps that are not powered by the Master. Failure of either Master or Slave Inverter may result in total (in the case of a Master Inverter) or Partial (in the case of a Slave Inverter) Backlight loss depending on the actual failure. Always ensure the supply voltages are present for the LCD Panel Control PWB and Inverter PWBs. In some cases, the Inverter PWBs are controlled by the LCD Panel Control PWB. If this is the case, loss of LVDS signal to the Control PWB may result in a NO Backlight condition. Always ensure the LVDS signal is present and the Supply Voltages to the TVs Video Processing ICs are correct. Failure or temporary fluctuations of the signal or voltages may result in Vertical Line failures or Video Image Freeze.
Block Diagrams
Examples of Signal Flow to the Panel
Power Supply PWB P a n e l Backlight Control Signals
Example 1
Control PWB (LCD Panel)
B a c k l i g h t
PWM_DIM
BL_ON/OFF
ANA_DIM P a n e l B a c k l i g h t
LVDS signal
Example 2
Here we show Examples of the Signal flow from the TVs Digital Signal Board and the TVs Power Supply to the LCD Panels Circuit Boards. As you can see; while both examples use the same general Power, Video and Backlight Control Signals; there are (2) general variations of the Signal path. Example 1 shows all the Backlight Control Signals passing through the Control Board to the Inverter Board. In Example 2, the Backlight Control Signals are passed from the Digital Signal Board to the Inverter Board. This block diagrams only shows the originating source of the signal. It is possible that the signals may pass directly through other PWBs . This is important because connector problems between PWBs may result in loss of 1 or more of these signals. When troubleshooting Backlight problems, always trace the Backlight Control Signals Path from Board to Board to ensure the signal is being passed from the Source.. to the Intended Point. Some LCD TVs will utilize a Master/Slave combination of Inverter Boards to power the LCD Panel Backlight. The Master Inverter may power half or the majority of the LCD Panel Lamps while the Slave Inverter will power the remaining Lamps that are not powered by the Master. Failure of either Master or Slave Inverter may result in total (in the case of a Master Inverter) or Partial (in the case of a Slave Inverter) Backlight loss depending on the actual failure.
Block Diagrams
LVDS SIGNAL
R0+ R0-R7 G0-G7
TV Video Process IC B0-B7
Data Enable
R0100 ohm
TV Video PWB
LVDS to TTL
100 ohm
100 ohm
R0+
100 ohm
100 ohm
8bit TTL RGB signal is converted to LVDS LVDS is a differential signal TTL Signal is converted to LVDS for transfer from the TVs Video PWBs to the LCD Panels Control PWB
PLL
RGB signals are 8bit TTL signal. The chart below shows how a color would be represented by the data. For example, a white raster is displayed by outputting all High data. Data Enable signals when information is ready to be displayed. LVDS is a differential signal. Two differential signals are sent by the LVDS transmitter and compared at the receiver. TTL Signal is converted to LVDS for transfer from the TVs Video PWBs to the LCD Panels Control PWB. TTL signals are limited to about 250MHz due to noise. LVDS is capable of up to 1GBps. LVDS uses a lower voltage swing of 350mV, compared to TTLs 3V, to allow faster clocking. Differential signal eliminates noise problems of TTL making LVDS better for signal transfer between TV and LCD Panel.
LVDS SIGNAL
Signal Breakdown
DE Data Enable Signal TV Total Vertical Display time TVD Active Vertical Display Period TVB Vertical Blanking Period TH Total Horizontal Display time THD Active Horizontal Display Period TC Clock
TCH clock high TCL clock low TDS data store time TDH data hold time TES enable store
TVB Vertical Blanking Period: timing of blanking pulse for pixels TH Total Horizontal Display time: timing of Horizontal signal information for panel THD Active Horizontal Display Period: period that the horizontal information is displayed on the LCD Panel TC Clock: timing signal for LVDS pixel data TCH clock high: clocks high swing TCL clock low: clocks low swing TDS data store time: time needed to store data to pixel TDH data hold time: hold time for pixel data TES enable store: enable signal for storage of data to pixel
Solution 1. Check LVDS Input to Control PWB 2. Check DC Power supply to Control PWB 3. Visually/Electrically check major components 4. Use symptom to diagnose problem Control PWB Failure Causes 1. Damaged PWB 2. Circuit Failure on Control PWB 3. NG inputs (video/dc) from TV PWBs
Troubleshooting the Control PWB is difficult due to the lack of schematics, the PWBs location, etc... To adjust for these, new methods must be used to determine faults of the PWB and close attention must be paid to the specific symptoms of the failure. Use the tips here to help determine Control PWB failures. No video failures must be classified to help determine what caused the failure. 1. No video, but the OSD and Backlight shows 2. No Video, but Audio is OK 3. No Videoat power ON, but after 13 seconds there is a picture 4. No video.after 15 minutes. Often times this information is requested from customers during the initial service contact, but the details are missed. Further information can help asses the failure prior to seeing the malfunction. This is not a panel failure and may just be customer mistakewrong input etc... There could also be a failure of the specific input being used since OSD added just before output to the panel. Trying a different input may help determine this problem. 1. No video with audio is a good sign of a panel problem. This could result from Inverter, Control PWB or Backlight failure. 85% of cases would be a failure of the Inverter or supply voltage to the inverter PWB. Knowing this helps determine the time and problems they may be experienced if attempting a fast TAT repair at the customers home 2. If the picture appears after a short delay, this may be a normal function of the TV. Many JVC TV have a short 13sec blanking period at power ON prior to the image appearing. Ask further questions to determine if this is the case. It is common for Technicians to forget to determine normal TV operation and Failure operation and spend hours troubleshooting a problem that doesnt exist 3. No Video after a long period requires more information. Is the backlight ONDid the TV shut DownAre the LEDs flashing. Details in this case will prevent you from chasing the wrong problem. Remember, detail is key when troubleshooting LCD TV and Panel failures. If you have the details, it makes it possible to determine a failure with the use of the information, block diagrams and flowcharts provided on the iSee Database.
Check the DC voltage to the Control PWB This is normally 9VDC to 12VDC This voltage is required to power the Control PWBs circuits and ICs In this case, the voltage has several inputs to the Control PWB Connections and voltages will vary between LCD panels
The control PWB requires a DC voltage (normally 9VDC to 12VDC) to power the Control PWBs circuits and ICs. During troubleshooting of Video Problems related to the LCD Panel, ensure that you check that this voltage is present. It will be necessary to check this voltage at the output of the TVs PWB supplying voltage to the Control PWB since measurement on the Control PWB would be difficult due to its location. If the voltage is missing at the TV side, try disconnecting the LVDS cable and rechecking the voltage. A shorted panel or Control PWB may cause the TV to Shut Down or the Voltage Supply to become shorted.
NG PWB
Control PWB has short of 12V supply
OK PWB
Test point Location, Markings and Results will vary between LCD Panels
The control PWB requires a DC voltage (normally 9VDC to 12VDC) to power the Control PWBs circuits and ICs. This is a simple check to determine if the supply on the Control PWB has been shorted. A shorted Control PWB may cause the TV to shutdown due to an overcurrent condition. Disconnecting the LVDS cable may allow the TV to Power ON in these cases. If Disconnecting the LVDS cable allows TV Power ON, use this check to determine if the Supply on the Control PWB has been shorted. A shorted LCD Panel may cause a similar Shut Down condition in the TV.
White Raster
JVC
Black Raster
JVC
Example from LT-42X478/V Schematic YA512 1. Input a White Raster using a Video Signal Generator 2. Check the LVDS signals a. Positive and Negative pins will be inverse signals of each other. For instance; 2+ will be an inverse of 2-. 3. Change to Black Raster and look for change from high to low 4. Only 2+ and 2- are shown in the example, but all should be checked. 5. Marking of these signal will vary
NOTE: Cold Solder or poor connections at this connector may result in Solarization Problems.
This schematic shows the partial section of the LVDS connection. The signal will appear to be similar to the RF waveform of a VCR, with the incoming video signal being modulated by that carrier. Positive and Negative pins will appear to be approximate inverse signals of each other. For instance; TA2+ will be an inverse of TA2-. This signal may be checked by using an Oscilloscope to monitor the signal for change. Keep in mind that this is a high frequency signal that is difficulty to monitor during the test. Perform the below to check the signal: 1. Input a White Raster using a Video Signal Generator 2. Check the LVDS signals 3. Input a Black Raster and you should notice video change from a High to low signal on the modulated carrier 4. Inverse signal should be seen when comparing + and -
RXINN0
(Recive in Negative 0)
The test point should always have the same impedance measurement at both the negative and positive input
RXINP0
(Recive in Positive 0)
The LVDS signal consists of (x2) inverse signals, a Negative and Positive signal. The test point should always have the same impedance measurement at both the negative and positive input for the signal. This should be the same measurement for all LVDS signal inputs on the PWB.
Similar to previous PWB discussed in the previous slide, look for the LVDS test points on the PWB and compare measurements. They should be approximately the same for all inputs on the PWB.
RX0N
(Recive in Negative 0)
The test point should always have the same impedance measurement at both the negative and positive input
RX0P
(Recive in Positive 0)
Similar to previous example, look for the LVDS test points on the PWB and compare measurements. They should be approximately the same for all inputs on the PWB.
Look for obvious signs of damage to the Control PWB. Check Fuses on the Control PWB. Many of the Input and Output circuits are similar. Compare similar items looking for defect. For example, the LVDS input to Control PWB or Drive Outputs from the Control PWB to the LCD panel.
Inverter Troubleshooting
Inverter failures 1. Blown fuse measure for open 2. Circuit failure visually inspect but difficult to detect. Check for input signals to determine if the PWB should be operating 3. Transformer failure
a. b. Shorted cannot distinguish since shorted and normal Output may have same impedance measurement. Require HV test to determine OPEN measure the output/input and compare Transformers to others on the PWB Loose/missing/cut Visually inspect PWB for this damage.
4. 5.
Connection failure
a. a.
Damaged PWB
Inverter Troubleshooting
Backlight Signals
Inverters DC Supply Voltage from TV Power Supply
2-40(No.YA428)
Examples are taken from LT-32X787 Schematic YA428 The BL_ON, PWM_DIM and ANA_DIM signals should be present for backlight function On the example shown, ANA_DIM is renamed DC_DIM at CN00W The Inverters require DC from the Power Supply to operate. The Inverters DC Supply Voltage from the TVs Power Supply will vary between LCD Panels and TV Models. Missing LVDS signal may also result in No Backlight defect
Here we show examples of the Backlight Power Supply and Backlight Control Signals. These examples were take from the Schematic for the LT-32X787.
There are (3) signals that MAY be used to control the Backlight. These are shown in the images located on the left of the screen.
B L ON or Backlight ON. This is a HIGH/LOW signal that signals the Backlight to turn ON or OFF.
A N A Dim or Analog Dim. This may also be referred to as D C Dim. This signal may be used to control the brightness of the Backlight. The Individual Inverter Ballast output current will be directly controlled by this input signals DC. A Higher DC Input.. will result in Higher output and Brighter Backlight. On the other hand, a lower DC input.. will result in a lower output and a Dimmer Backlight.
P W M Dim or Pulse Width Modulation Dim. This is a modulated signal that may be used to control the brightness of the Backlight. In this case.. the Inverter Output current is fixed, but the duty cycle of the PWM signal determines the OFF/ON period of the Inverter. A longer duty cycle will result in a brighter backlight, while a shorter duty cycle will result in a dimmer backlight.
Keep in mind that the naming of these signals may vary with the various TV models. Also, the signal name may change throughout the schematic. It may be best to follow these signals from the Inverter Board back to the TVs Microprocessor during troubleshooting. Ensure that the signals are present at both location. Also keep in mind that some TVs will not utilize all the Backlight Control Signals.
In the image on the Left Side.. you will notice the schematic showing the Inverter Boards DC voltage Supply from the TV Power Supply. Always check these voltages when troubleshooting backlight problems to ensure they are present and stable. This DC voltage will vary based on TV Model and Panel Size.
Be aware that a missing LVDS Signal can result in the loss of the LCD Panel Backlight. This will result in both loss of Video and Backlight. Ensure that the LVDS signal is present to ensure that this is not the issue.
Inverter Troubleshooting
PWB layout
Inverter PWBs consist of a Control Circuits and Power Circuits. The Control Circuits provide voltage regulation, Power ON/OFF and Feedback. There are generally multiple Power Circuits. The Power Circuits are usually split into (x2) identical section on the PWB. You can use these similarities to test for component malfunctions on the PWB by taking Measurements from the PWB Ground. Many Inverter PWBs provide test points locations on the PWB that make these tests convenient.
Inverter PWBs consist of a Control Circuits and Power Circuits. The Control Circuits provide voltage regulation, Power ON/OFF and Feedback. There are generally multiple Power Circuits on the Inverter PWB. Each Circuit is identical in design and function. The Power Circuits are usually split into (x2) identical section on the PWB. You can use these similarities to test for component malfunctions on the PWB by taking Measurements from the PWB Ground. Many Inverter PWBs provide test points locations on the PWB that make these tests convenient.
Inverter Troubleshooting
Ballast Circuit Check 1/2
Lamp output from the inverters ballast circuits share identical circuit designs. Use the other circuits to help diagnose Lamp Output Circuit faults on the Inverter PWB. Output Impedance to the lamp will measure the same at the test points located by the Lamp Connectors. This will detect OPEN Transformer. Shorted Transformer will not show by this method normally.
Measurements are Approximately the same, so outputs are assumed OK. Compare to remaining circuits on PWB to determine the normal output measurement
Lamp output from the inverters ballast circuits share identical circuit designs. Use the other circuits to help diagnose Lamp Output Circuit faults on the Inverter PWB. Output Impedance to the lamp will measure the same at the test points located by the Lamp Connectors. This will detect OPEN Transformer. Shorted Transformer will not show by this method normally.
Inverter Troubleshooting
Ballast Circuit Check 2/2
The NG circuit measured at 5.03K. All others measured at approx 5.3K ohm. Large differences may be a sign of Circuit failure. In this cause, the failure resulted in a NO Backlightcondition. The Inverter PWBs consists of Control Circuits that will Shut OFF the Backlight if failures are detected. Backlight Shutoff due to the Inverters Failure detection will usually occur within 3 seconds of the Backlight showing. This will not cause the TVs LEDs to flash unless the failure is also detected by the TVs PWBs.
OK Circuit
NG Circuit
The NG circuit measured at 5.03K, All others measured at approx 5.3K ohm. Large differences may be a sign of Circuit failure, In this cause, the failure resulted in a NO Backlightcondition. This Inverter PWBs control circuits usually sense these differences or failures. The Inverter PWBs consists of Control Circuits that will Shut OFF the Backlight if failures are detected. Backlight Shutoff due to the Inverters Failure detection will usually occur within 3 seconds of the Backlight showing. This will not cause the TVs LEDs to flash unless the failure is also detected by the TVs PWBs.
By shining a flashlight into the screen you can check to see if picture data is on the LCD Panel when the backlight is not operating.
Another method of troubleshooting a no picture/no backlight problem, is to check for a picture on the screen by shining a flashlight directly into the screen. This will, in effect substitute, the flashlight for the backlight. If the LCD panel and video circuits are working properly and the backlight is not, then you should be able to see the picture faintly on the screen. A very large flashlight had to be used to take the pictures shown above.
If the Inverter fails or the Backlight Bulbs do not ignite, the video signal may still be present. If this is the case, it may be possible to see the TV video with a large flashlight. By Shining a Large flashlight at an angle toward the screen; some of the video may become visible. The presence of Video without the Backlight is a clear sign of an Inverter problem. Further troubleshooting of the Backlight DC supply and Backlight Signals is necessary to determine if the Inverter requires replacement.
Keep in mind, a very bright flashlight is required for the test to effectively work. Additionally, the video is difficult to see under these conditions. Therefore look closely and double-check your results.
This Test will only be useful if the LCD Panel and TV Video Circuits are fully functioning. Certain other LCD Panel and TV Video Circuit failures may also result in Backlight malfunction.
Inverter Troubleshooting
Inverter Output test 2
A Voltage tester may be used to test the individual Lamp Outputs from the Inverter PWB. This will help access if a Bulb in the panel is blown or if the Inverter has no output to the Bulb. 1. 2. 3. 4. With the TV Power OFF, disconnect Bulb to allow insertion of the Tester. Insert Tester to allow testing of the output. Turn ON TV power. The Light, on the Tester, will flash to show Good output from the inverter.
The Inverter tests for load upon TV Power ON. If no load is present, it will not provide an output. If the tester is connected after TV Power ON, the test will always fail.
This is a simple test for checking the output from the Inverter to the Backlight. The Inverter Board uses individual Ballast circuits to power the LCD Panel Backlights. It is possible to test these individual outputs by using a Simple AC line Voltage Tester. While the TV Power is OFF. Disconnect the Lamp output from the Inverter Board. Insert the Test Probe into the connector on the Inverter Board, Polarity is not important. When you Turn ON the TV Power, Watch for the Test Probe to signal the circuits. function. The tester should flash ON, Then OFF if the output is functioning. A Good Test will signify that the output to that Lamp is working only.
It is important to remember that some Inverter Boards will look for a load upon Power UP. If a load is not present, the Inverter will shut off. While attempting this test, ensure that the Test Probe is connected prior to powering ON the TV. If this is not done the Inverter Board will shut down before your are able to check the output.
BACKLIGHT
The Backlight is made up of many small thin Fluorescent Tubes.(1) Each individual fluorescent tube has its own ballast or inverter circuit.(2) This Backlight provides the Light Source for the LCD Panel Image.
Without the Backlight, The Image may be created by the LCD panel, but will not normally be viewable. DIFFUSER The diffuser is made up of multiple layers of material. (3)
Inverter/Ballast Circuit
This material ensures that there is an even dispersion of light on the panel. (no bright spots)
BACKLIGHT The Backlight is made up of many small thin Fluorescent Tubes.(1) Each individual fluorescent tube has its own ballast or inverter circuit. (2) This Backlight provides the Light Source for the LCD Panel Image. Without the Backlight, the Image may be created by the LCD panel, but will not normally be viewable. DIFFUSER The diffuser is made up of multiple layers of material. (3) Multiple layers of diffusion material are used to create an evenly illuminated picture. This material ensures that there is an even dispersion of light on the panel. (no bright spots)
Start
YES
TROUBLESHOOTING FLOWCHART
YES
NA
YES
OK
OK
OK
Lines in Display
NO
NG
NA
OK
Missing Pixels
YES
NO
Not a Panel Defect Check LVDS signal, cable and connections (3)
NG
OK
(1) Check for appearance of Backlight through LCD Panel frame, as this may not be visible from front of TV. (2) Refer to Backlight Troubleshooting section (3) Refer to LVDS Signal Section (4) Refer to LCD Panel PWB function section
Follow this flowchart to assist with the diagnosis of LCD Panel failures.
Use the supplied troubleshooting steps from this guide and commonly practiced troubleshooting steps to eliminate potential causes of the failure.
When troubleshooting NO VIDEO problems.. always look for the presence of a backlight before proceeding. The Backlight may be difficult to see under normal conditions, so it may be necessary to look for this on the sides of the LCD Panel frame.
EXAMPLES
Control PWB failures
Other failures may present with similar symptoms
The Control PWB only causes this defect when the Backlight Control Signals are Output from the Control PWB
White Display
No Display
Here we show examples of defects that may be caused by the Control Board of the LCD Panel. If it is decided that the Control Board is faulty through troubleshooting, refer to the Service Manual for the Part Number of the part required. Many of these Error may reflect errors that may be caused by the TVs Video Circuits. Display the TVs User menu to eliminate SOME of those TV Circuit Failures. When the failure does not show in the TVs User Menu, the error cannot be the LCD Panel or its Boards. If the error shows in the TVs User Menu, further troubleshooting is required to determine the appropriate source. Abnormal Display On Half of the Screen is caused when the Control Board is unable to properly address a portion of the screen.. resulting in No Video Output in that area of LCD Panel. No Display conditions may occur under several circumstances. This symptom may occur with or without the presence of a backlight since the backlight signals are often passed from the Control Board to the inverter. White Display, Noise in the Video and Wavy Color Shading can all result from an improper video output from the Control Board. This will occur when the Control Board does not properly bias the drive ICs of the panel causing this video error to occur.
EXAMPLES
LCD Panel Defects
Other failures may present with similar symptoms
Partial No Display
Gate-ICs drive the horizontal lines. If a gate-IC is broken, other gate-ICs below it will not be driven as well.
Here we show examples of defects that may be caused by the LCD Panel. If it is decided that the Panel is faulty through troubleshooting, refer to the Service Manual for the Part Number of the part required. The Errors shown here Partial NO Display.. Color Shading.. and Vertical or Horizontal Line may all be caused by a failure of the Drive ICs within the LCD Panel. These Drive ICs bias the Pixels of the display turning them ON or OFF. In the Case of Partial NO Display shown, since gate ICs are driven in Groups, the failure of a single IC will result in no operation of the ICs below it in the group. A Bright Dot defect results when a pixel is always on. This is tested using a Black or dark Video pattern. A Dark dot defect results when a pixel will not turn ON. This is tested using a white pattern. In both instances it is necessary to check the defect against the specification of the TV Model and LCD Panel. This defect is easily seen when using a Magnifying Glass to view the pixel. By doing so, you will be able to judge the Pixels color, size, and shape if needed.
EXAMPLES
Inverter Defects
Other failures may present with similar symptoms
No Display
Partially Dark
(dark band in image) See also LCD Panel Defect Examples
Some Panels use (2) Inverter Boards, Master and Slave. For these models Confirm the symptom and check the corresponding PWB. If the voltage for the Backlight is not supplied, luminance-shading could occur. This is difficult to identify with a normal picture. Therefore, when you check this, input an all-white picture to confirm the phenomenon.
Here we show examples of defects that may be caused by the LCD Panels Inverter or Inverters. If it is decided that the Inverter is faulty through troubleshooting, refer to the Service Manual for the Part Number of the part required. No Display conditions will result when the Backlight is not operating. This may be caused by both an inverter or backlight failure. In these cases, the TV Audio may be heard and the LCD Panel may still display video, but this video will not be easily seen since the Backlight is not operating. Use the previously discussed troubleshooting methods to assist in the diagnosis of this failure. Partially Dark image may be the result of one of the Inverters not functioning at peak capacity due to low input voltage or failure. Since these errors are difficult to see.. input a 100% all white video signal to aid with the diagnosis. This may also be caused by a faulty backlight. Some failures may not show with 100% video input.. So it is often wise to lower this input signal to about 25-30% to insure that the Backlight remains evenly spread over the panel under all circumstances.
EXAMPLES
Backlight/Diffuser defects
Other failures may present with similar symptoms
No Display
Partially dark
(dark band in image) See also LCD Panel Defect Examples Some backlights may not be functioning
Dark Lines
See also Inverter Defect Examples This may be caused by damaged or shifted diffuser
Dark Lines and Partially Dark Color, may result if there is a defect in the diffusion material used to evenly spread the light produced by the LCD Panels Backlight. Since the light is not even in an area, that area will appear darkened. This is easily visible with bright white video. No Display conditions will result when the Backlight is not operating. This may be caused by both an inverter or backlight failure. In these cases, the TV Audio may be heard and the LCD Panel may still display video, but this video will not be easily seen since the Backlight is not operating. Use the previously discussed troubleshooting methods to assist in the diagnosis of this failure. Partially Dark image may be the result of one of the Inverters not functioning at peak capacity due to low input voltage or failure. Since these errors are difficult to see.. input a 100% all white video signal to aid with the diagnosis. This may also be caused by a faulty backlight. Some failures may not show with 100% video input.. So it is often wise to lower this input signal to about 25-30% to insure that the Backlight remains evenly spread over the panel under all circumstances.