DOCUMENT NO Taiz REV
SECARIGT| “mmsmexysssmmmurnsrmucrion ras
"FOR IV 1008 NON: FLUIDIC MANIFOLD °
Ser gor
PURPOSE:
This procedure ist instruct authorized personnel to replace and calibrate Sechrist Model
IVI0OB Fleidic Manifold wth Non Fludic Manifold
WARNING: This Ascembly and Calibration process involves apening the ventilator
enclosure, which constitutes an ELECTRICAL SHOCK HAZARD. This procedure must
be performed by qualified service personnel,
ITEMS (PIN) SUPPLIED:
Pare Description
213s Paeurtio Control Masiteld
v3 1032.x V8" NPT Adapter
Tv310 16" Tube fixing
50035 Aur Valve
42700 Dutton, Manual Death Valve
43418 Retaining Ring
v3t Fitting, Tube 1/8
HB333 Tube, U8" x 14"
1305-1 Tube, V8" x 2" Tygon
1301-048 Retaining Fine
‘ 1302-02 Valve Cover
Iv3i8.02 ‘Tape Do. side 1.7716 DA
3635 Plug 10-32 x1/4"hex head
REQUIRED TOOLS:
0-60 ps pressure gue 0-Spsi pressure gauge
78° Slots Serew Dever Retaining Ring Pliers
32", 5168”, 7164” Hex Driver 3/16" Allen Wrench
TAS" Wrench Teat bingDOCUMENT NO. 1a0i06 TEV
CALIBRATION / ASSEMBLY INSTRUCTION | PAGE:2
ae
SECARIST | “roxy toon sow: erumte manteorn ‘Ons
er
SECTION 1: Dissesembly of a9 existing Fuidic Manifold
Remove for serews holding te lower contol pane to the control mos as
Tustrated ia Fig.
2 Remove foe serews from the back pane and disconnect itbon cable fo
MPU board
FIG.
Remove Inspiratory and Exp:atory contol knobs from the low
ilurrated in Fig. 2
1.3 Disconseet the golenold sd ll ubing fom the existing Flac Manifold as
ilusrated in Fig. 2.
1.6 Use retaining ing plies to emove the seap rt
and Expiatry control vaives as ilustate ia Fig, 2.DOCUMENT NOTTS
CALIBRATION / ASSEMBLY INSTRUCTION
LS Remove existing Manual Dresth Valve and Manual Bronth Button and Mansa
Breath Cover aillstrate in Fig 2.
1.6 Remove existing Fuidie Manito
FIG.2
SECTION: Assembly of a New Non-Fluidic Manifold
NOTE: Use Teflon tpe.on PAY IV321
2.1 tfnit has 1/16" bing from mixer o manifold, remove epilator asexbly (PIN
[V3i8) fom ventilator. Remove double back tape ffom botiom of ear.
Remove one existing 1/8" NPT plug nd the we Binge athe in and wut postion
Secure (3) l0-32808 adapter (P/N IVS2!) and Q) UR abe Bitings (PIN VST)
in and out positions, secure 1/15" re iting (PIN IV310) a illustrated in Fig3
Mark “in” side of regulate for exy installation, Replace double back ape
regulator. Remove 1/15" tbe iting from mixer and secure 1/8" sabe fing (PA
311) Inca regulator back in ventilate Replace old 1/16” tubing wth 27N
1HIBS33 aerated in FinCALIBRATION/ ASSEMBLY INSTRUCTION | PAGE :4
FOR IY 1008 NON- FLUIDIC MANIFOLD. ‘OF:8
oro
DOCUMENT NO. 140126 REV?
22
23
26
27
28
29
210
‘anit has 1/8" abn temove one existing 1/8" NPT plug ftom the regulater
astembly a lustrte in Fig 3 Secure one 10-32. UR adapter (P/N321) and
VIG" tbe iting (PINBLO) to te regulator assembly.
nsall new style manual breath valve with retaining ring and manual breath cover
sv illestrsted in Fig 3
(Carfilly take New Non-Fluidc Manifold (P/N 21435) out ftom the package.
Align the Inspiratory and Bxpiratory Control Valves tthe appropriate holes in
lewer control panel.
Use retaining plier to snap the retainieg ring back onthe Control Valves.
Install inspiratory and Expiratory Control knobs as illstated in Fig. 3.
NOTE: To install the lspratory und Expratory pressure knobs, fis rotate the
Inspiratory and Expiratory valve stems clockwise until they seat gently. Roiate
‘each valve stem counterclockwise 90" + 15°; instal the knobs with nob stop pin
resting against the valve stop pin. Tura both valves fill counterclockwise.
Connect Solenoid.
(Connect al tubing back to New Non-Fludic Manifold as illustrated in Fig. 4 and
reconnect the bon able.
CCalibeate the Ventilator per inscuctions specified in Section 3.DOCUMENT NO. Ta TENS
CALIBRATION / ASSEMBLY INSTRUCTION | FAGE :6
FOR IY 100B NON. FLUIDIC MANIFOLD OF:
porn
|
FiG.4DOCUMENT ROTO TEV
CALIBRATION / ASSEMBLY INSTRUCTION | PAGE: 7 q
FOR IV 1008 NON. FLUIDIC MANIFOLD {
SECTIONS: CALIBRATION INSTRUCTIONS
sa serur
BAL Connect 50 psi ai and oxygen supply tothe ar and oxygen iting a usted in
Fig. 4 he gas mixer. Connect patent eit astembly, test ng and
valve, Turn ele valve all he way in.
3:42 Connect 0-60 psi pressure gauge to the gus regulator assembly (PAN TV318).
3.13 Open R4 A RS Yur RS 1 ar, RH tum and R24 tum onthe new Non {
Fludic Maaifold. Remove plug snd install ne (V310(1/16" tbe Siting) por.
Eon the Nou Fluide Manifold as shown in Fig. 3. Connee: 0-5 pi pressure
‘gauge tothe prt abeed "E i
Note: Reference Fig. 4 forthe valve locations
34 Plug innit
3.2 Calibeste Proveure Regulator
3.21 Tum the gu supply valve on and set he outpt pressure to SD psi. Adjust the
regulate 1015 0.5 px. Push down the locking ring util it taps in position,
322 Sethe mixer flowmeter te 12 LPM
3.3 Set the mish Inspiratory pressure:
‘Tam ventlatorto vent mode. Tur inipirtry time to 1.00 and expiratory ime to
0.70. Adjust the RS with screwdriver unl the manometer on the vent ato: reads
S41 em ofFh0,
34 Set he maximum Inspiratory pressure
34.1. Slowty tum the Inpiratory contol knob fly clckwise. Adjust RS with
secendevet ual the ranometer on the Yat stor reads 70-73 em of 0
Recheck the minimum Inspiratory pressare and adjust ifcecessary
35 Adjest
smisimam Expiratory pressereseting,
351 Adjust B3 until the pressure gauge veads 2780DOCUMENT NO. 140126 REVS
seaRTamaasentmaneNaGLS |G
=" B08T#70
39
‘Adjust the maximum Expiratory presure setting,
‘Slowly Turn the Expiratory pressure control knob to fully clockwise. Adjust the
4 unl the manometer on the ventilator reads 20 ¢ 2.0.em #0.
‘Vorify the minimum Expiratory pressure.
‘Tam the Expiratory pressure contol knob counterclockowise unt it stops. Verify
the manometer reads (-1.5) to (-6.5) cm of HO. Adjust R3 until the manometer
reads (+13) t9 (-6.5) cm of HO. Recheck max. and mia. inspiratory and max
expiratory pressure and adjust if necessary
Adjust the manual breath button
‘Turn the ventilator mode to CPAP. While pushing manual breath bution, slowly
tum the Inspiratory pressure control knob fully clockwise, Adjust R2 to70-7S em
of H,0.
‘Set manual breath prossure t 30 ce, Tur knob to vent mode Inspiratory
pressure should read + 2 em of manual breath pressure. Adjust pressures if
necessary
(Cheek for interaction.
3.9.1. Tum the Mode Switch to Vent. Tur the Inspiratory pressure control kncb
until the manometer reads 30 + | em of Hy0. Turn the Expiratory pressure
‘contol knob counterclockwise to cloclowise. Verify tat the manemetce
reading does not vary by more than 3 em of H:O. Repeat with Inspiratory
Pressure set between 70 and 75 em HO. Tur the Expiratory pressure
control krob until tbe manometer reads 10 Lmof HzO. Tarn the
Inopiratory pressure conirol knob counterclockwise to clockwise, verify
that the manometer reading des not vary by mare than 3 em af HO.
Repeat with Expiratery prestuce set between 0 and -2 em HO.
SECTION 4: FINAL CLOSE UP.
41
42
43
44
‘Tum off power, air and oxygen supplis.
Remove 0-60 psi gauge ftom the regulator assembly. Remove {iting (IV310)
from the regulator assembly and intall fiting (P/N 3635) in the regulator
Remove C-5 psi pressure gage from the port E on Manifold ard install the plug
‘back tothe Manifold as supplied originally.
Install the four screws in the bark pane! and in the lower control panel