ULTRACINESE
SECRET: The effect is performed using a pulse motor
that produces vibrations. The magician installs this
device on his forearm using a leather watch band or
rubber band. The vibration produced is conducted from
the device, through the fingers used to hold the bolt,
‘and amazingly enough the vibration causes the nut to
spin on or off the bolt. Its important to install the pulse
motor correctly for best results.
PREPARATION: The gimmick is composed of three
important parts: 1) The control box that is attached to
the magician's waist (belt or pants) using the clip. This
Control box is the main switch that Is used to power the
‘equipment on or off. The control box switch has 3
positions. The middle position is the “off” position and
the side positions turn the equipment on (one side
position causes the motion to reverse. You will need to
‘experiment and familiarize yourself with the switch)
Install a new standard AA Battery in this control unit
prior to starting, 2) & trigger button that is installed
under the magician’s footitoe. The wire runs from the
main control box, down the inside of the pant leg along
your leg, It continues to the bottom of your foot with the
trigger button in contact with your big toe. When you
press down on your big toe you will feel the button
being activated. Use a rubber band to fix the trigger
button to the correct position on your foot. 3) A wire
then goes up under your shirt from the control box and
down the inside of your sleeve to the Pulse motor
Page 1
HANDLING: Secretly turn the switch on the main
‘control box on (at this point you are not activating the
toe switch). Openly thread the nut on the bolt. With the
palm of your hand pointing upwards hold the head of
the screw tightly between your index finger and thumb
of the hand with the pulse motor on it. The pressure
between your fingers and the position of your wrist will
determine how fast the nut spins. Start moving your
‘wrist until the bolt is paralle to the floor and protruding
ina straight line from the forearm with the pulse motor
(straight out from the pulse motor unit)
‘Apply pressure down on your toe to activate the toe
switch. This causes a vibration to travel from the pulse
motor, through your arm and hand, and the vibration
‘causes the nut to slowly unwind from the bolt. You can
slart or stop the movement by activating or deactivating
(pressing down on or lifting off ofthe toe switch. Prior
to ever performing this you should find the best position
of holding the nut and bolt to maximize the vibration,
Now you can flex your wrist clockwise or counter
clockwise and move your arm a little bit in @ way to find
the best position. To perform the reverse movement of
the nut onto the bolt use the same steps and when it
starts to spin, flex your wrist upwards slowly (as if you
are going to drink something). It wil make the nut spin
in reverse, Another more surefire way to reverse the
spinning rotation, without changing the handling
movement, isto invert the power switch on the control
Page 3
which is the heart of the equipment. Install the pulse
‘motor against your forearm or wrist using a watch band
Cor rubberband to fix it tightly against your wrist. You
need to be wearing a shirt with long sleeves to hide the
wires. It is. imperative that the pulse motor rest
TIGHTLY against your arm to maximize the vibrations.
Thus ensure the watch band or rubber band is tight
(but do not cut off circulation to your hand). For best
results with Ultracinese you will need to be familiarized
with the vibration produced by the pulse motor. With
this vibration you will perform many amazing effects.
‘The effect with the nut and bolt for example, you have
to find the best position of your hand and wrist to cause
the nut to spin faster and faster. A few points here.
Make sure the Pulse Motor is TIGHTLY fixed against
your wristforearm. Hold the HEAD of the bolt very
tightly (avoid contact with the shaft of the bolt). Hold
the bolt so its paralle! to the Pulse Motor (in a straight
line with it) to maximize vibrations. The secret is to
‘maximize the conduction of the vibration through your
hand, so practice and find the best position and holding
force. You will find more details regarding the handling
in the bonus instructional DVD.
Before starting your presentations, check the switch to
know for which side is the regular spin and which is the
reversed.
Page 2
box. After you are finished with the effect, show your
hands empty and give the nut and bolt for examination,
When you are alone and done performing turn the
switch on the control unit on your belt to the off
position
Ensure that when you hold the bolt you hold it by the
head of the bolt and apply a good amount of pressure,
holding it very firmly between your thumb and finger.
You will find in the bonus demo DVD many others
amazing effects with Ultracinese.
The brass screw that comes in your kt is not attracted
by the magnet. You can use the magnet that comes.
with Uttracinese to prove that you are not using this,
property to perform the effect. Do not leave the
batteries in the unit when not in use for an extended
Period,
Ultracinese contains: Electronic Device (control box,
‘rigger button and pulse motor), 2. screws with nut
(steel and brass), magnet and Instructional DVD.
Ultracinese requires: One standard AA battery (not
included). The battery must be put in the control box
prior to use.
‘Thanks you for purchasing Ultracinese. We hope you
enjoy it
Created by Leonardo Milanos
Page 4