Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Table of Contents
Introduction...............................................................................................................1
Catalog Guidelines....................................................................................................2
Shaft Seal Features.................................................................................................. 3
Seal Numbering System........................................................................................... 4
Seal Selection Process.............................................................................................5-14
Seal Types....................................................................................................... 5-9
Operating Limits................................................................................................ 10
Lip Material Selection......................................................................................... 11
Properties of Basic Lip Materials................................................................... 11
Fluid/Elastomer Compatibility.......................................................................12
Based Upon Shaft Speed............................................................................ 13
Metal Case and Garter Spring Selection.................................................................. 14
Standard Seal Width and Minimum Radial Cross Section............................................ 14
Shaft Recommendations...........................................................................................15-16
Shaft Hardness..................................................................................................15
Shaft Surface Finish............................................................................................15
Shaft Tolerance................................................................................................. 15
Shaft Chamfer...................................................................................................15
Shaft Eccentricity...............................................................................................16
Housing Recommendations...................................................................................... 17-18
Housing...........................................................................................................17
Housing Bore Chamfer........................................................................................ 17
Housing Bore Finish........................................................................................... 17
Housing Bore and Seal O.D. Tolerance................................................................... 18
Installation Procedures.............................................................................................19
Clark Seal Numbers..................................................................................................20-43
Inch................................................................................................................ 20-40
Metric............................................................................................................. 41-43
Interchange Tables................................................................................................... 44-61
Chicago Rawhide...............................................................................................44-50
National...........................................................................................................51-57
NOK............................................................................................................... 58-61
Conversion Tables.................................................................................................... 62-64
Shaft Seal Selection Considerations.........................................................................inside back cover
Clark Seals , since 1956, has designed, manufactured and supplied oil and grease seals to protect all types of equip-
ment. Clark Seals developed the original Sheave and Excluder Seals and was one of the pioneers in the development of
vacuum molding technology to reduce premature seal failure. Clark Seals continues to search for the latest innovative design
technology to develop the highest quality seals for less. Clark holds patents on a variety of seal designs, including the Full–Face
CO and CN for ball and roller bearings, the CSL washing machine seals and the latest CSL PREMIUM that provides maximum
protection in harsh operating environments for bearings.
Clark Seals is customer focused. Each customer is assigned an Account Manager, who coordinates all
the activities from design through delivery. Clark maintains a 90–day inventory for next day delivery on all blanket order
accounts. Inventory control through company intranet guarantees up to date and reliable information to help meet customers
needs.
Clark Seals is design (technology) oriented. Clark designs shaft seals to SAE, RMA, ISO and DIN
3670 standards. AutoCAD design drawings and specifications are produced from application information supplied by the
customer. Molds are produced with CNC/CAD controlled manufacturing to produce the most complicated seal design and
assure precision to the smallest details. All critical seal dimensions are specific to the type of elastomer required. The latest
SAE Optimum seal design standard is our most common design. The drawing and specification are supplied to our customers
for review before production. They can be electronically transmitted to the customer for their purchasing, inspection and
engineering requirements.
Clark Seals is ISO 9001 certified. Clark’s control and oversight of critical design, purchasing and manu-
facturing processes insure quality and repeatability. Our Tulsa manufacturing plant utilizes the latest inspection equipment to
verify the seals are produced to the design specifications. A 20X optical comparator is used for precise measurement of the crit-
ical seal geometry. A radial lip force gauge is used to determine the seals ability to function properly over time. Rubber analyz-
ing equipment confirms the important tensile strength and durometer requirements. Inspection equipment also identifies the
metal case and spring materials. Electronic and digital measuring equipment accurately measures all the critical seal dimen-
sions. An inspection report can be furnished with each shipment at the customer’s request.
At Clark Seals we take pride in our ability to meet the design challenges presented by our customers. We
are an established company whose primary purpose has been to reduce the cost of quality for our customers.
At Clark Seals better quality costs less!
1
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Catalog Guidelines
The purpose of this catalog is to provide the user with a guideline for the selection of a standard seal in a general application.
Many sealing requirements, however, require a seal to function beyond the design limits of a standard seal. This catalog
identifies factors to consider in selecting standard shaft seals and their design limits.
The “Shaft Seal Selection Considerations” page in the back of this catalog is used in the seal selection process. For assistance,
contact Clark Seals, Ltd.
c t i o n o r Design
Sele
I N E S
H ELPL (800) 56 5 1
-12 4 0 • (918) 6
64-00587
) 664-1146
7
FAX: (918 o m
kseals.c this catalo
g.
www.clar s ea ls listed in x pe r i e nce , and
the
t limited to
t line is no f pr od uct i o n & t y p e o f s h a f t s
e
design eal.
rk produc
The Cla r s o n d
more than
4 5 y e a ally a n y s i ze a
irtu
We have provide you with v
we c an
2
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Shaft Seal Features
Metal Case
Inner Metal thickness
Case Spring position
(R Value)
Garter
Spring
Head Height
Flex thickness
Scraper
Angle
Barrel
Angle
Inside
Excluder
Shaft Lip
Diameter Angle Excluder Lip
I.D.
Primary sprung Beam Length
Sealing lip I.D.
3
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Seal Numbering System
Clark’s seal part numbers are created with letters designating the lip and case design followed by the shaft diameter,
housing bore and the seal width in inches or metric. Example: a seal designated by TB2–1.750–2.500–.312–SSSVL
If the letter “U” is in front of the lip design letter designation, it identifies a unitized seal. The letter “T” and/or “P” following the
case designation letter indicates a Teflon ring molded to the sealing lip or a seal designed for pressure. The letter “L, R or W”
following the case designation letter indicates a hydrodynamic sealing lip.
Case Designs
Lip Designs A – Additional metal case
D – Two spring loaded lips A2 – Metal with inner metal case
E – High dynamic eccentricity lip B2 – Metal O.D.
F – Felt lip B – Metal O. D. rubberized inner case
K – Double lip, non–spring loaded BR – Metal O.D. rubberized inner case with nose gasket
L – Counter–clockwise rotation helix C – Rubber covered O.D.
M – Mud excluder lips F – Completely rubber covered
P – Spring loaded pressure lip G – Corrugated rubber O.D.
R – Clockwise rotation helix H – Rubber covered O.D. and rubber covered exterior metal case
S – Single lip, spring loaded J – Flanged metal case for positioning
T – Double lip, spring loaded J1 – Reinforced flanged metal case
V – Single lip, non–spring loaded HC – Metal O.D. install from either direction
W – Bi–directional rotation helix N – Partial rubber and partial metal case O.D.
WP – Wiper lip
Y – Single lip, non–spring loaded, flushing feature Case Material
Z – Side lip sealing against a vertical surface Blank – Carbon steel
S – Stainless steel
Lip Materials B – Brass
Blank – Nitrile
V – Viton (Fluoroelastomer) Metal Case O.D. Materials
P – Polyacrylate Blank – No Latex coating
T – TFE (Teflon) L – Latex coated O.D.
EP – Ethylene Propylene
E – Neoprene Garter Spring Materials
Si – Silicone Blank – Carbon steel
Teflon is a registered trademark of Dupont. SS – Stainless steel
4
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Seal Types
Generally, seals with spring–loaded lips are used for retaining oil lubricants and non–loaded lips are used for low–speed grease
retention. Metal O.D. seals are more suited for steel and cast iron housings. A press fit metal O.D. seal has greater holding
strength and better alignment. As a general rule, the shaft surface speed of the “V” and “K” type seal should be less than 10
M/s (33 feet/sec.)
Case Design A2 B2 B BR C
Lip Application Metal O.D. design Most common and Metal O.D. design Metal O.D. design Rubber covered
Design and with an inner case economical metal with fluid side with a nose gasket O.D. design for
Description for greater O.D. design. rubber covered. for face sealing excellent
structural rigidity. and the fluid side is O.D.
rubber covered. sealing.
Economical
design, single
lip for grease
V retention or
sealing
viscous fluids.
VA2 VB2 VB VBR VC
Double lip
economical
design, grease
K retention or
sealing viscous
fluids. Light dust
exclusions.
Dust wiper or
scraper for
WP hydraulic or
pneumatic
cylinder
applications.
WPB WPC
5
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Seal Types
Rubber O.D. seals are preferred for soft alloy or plastic housings and is the best choice for rough bore finishes above 100u inch
(2.54µ M,) or for applications where the housing is subject to large thermal expansion.
6
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Seal Types
The “D” seal designs utilize two spring loaded lips to separate
two fluids. Seals are generally wider to accommodate the two
working lips. The bore depth will generally increase.
DH DF DB2
The “P” and “P1” seal designs have spring–loaded lips and a
short beam length for medium pressure sealing. For applica-
tions up to 50 psi (3.5 kg/cm2) and shaft diameters under 2.5”.
THP SCP1 SCP Maximum pressure depends upon shaft speed and total eccen-
tricity. Stiffness ratio varies with shaft speed and cavity pres-
sure. It is recommended to use a higher durometer rubber in
pressure applications.
The “M” seal designs are for mud sealing. Extremely dirty
applications at low rpm. Designed for irrigation and agricultural
equipment. When the seals are installed, the lips interfere with
the shaft and point away from the bearing cavity.
MA2 MB2 KB2
The “O” seal designs are like the standard designs except with
an external lip. They are designed for sealing against a rotating
housing such as a front wheel hub.
7
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Seal Types
The “Y” and “HC” seal designs are for light–duty dust
exclusion and they allow spent grease to be flushed out of
the bearing cavity.
8
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Seal Types
9
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Operating Limits
Operating limits for spring–loaded lip seals such as the S, T and D designs
Shaft Nitrile lip maximum Maximum continuous Maximum total
Diameter Continuous shaft speed pressure eccentricity
General 3500 rpm 5 psi 0.016”
0.500” (13 mm) 7000 rpm 5 psi 0.004”
1.500” (38 mm) 6000 rpm 5 psi 0.006”
2.500” (64 mm) 4000 rpm 5 psi 0.010”
3.500” (89 mm) 3500 rpm 5 psi 0.013”
4.500” (114 mm) 2600 rpm 5 psi 0.017”
Note: Higher speeds are possible using high temperature elastomers. Higher eccentricity with slower speeds.
Operating limits for non–sprung lip seals such as the V and K designs
Shaft Nitrile lip maximum Maximum continuous Maximum total
Diameter Continuous shaft speed pressure eccentricity
General 2000 rpm 4 psi 0.005”
0.500” (13 mm) 3500 rpm 4 psi 0.003”
1.500” (38 mm) 2500 rpm 4 psi 0.005”
2.500” (64 mm) 2100 rpm 4 psi 0.006”
3.500” (89 mm) 1500 rpm 4 psi 0.008”
4.500” (114 mm) 1200 rpm 4 psi 0.010”
Note: Higher eccentricity with slower speeds.
S type lip T type lip D type lip V type lip K type lip WP type lip
These limits are based on the assumption that the heat is being conducted away from the lip through the lubricating fluid and
shaft. A delicate balance must be achieved in an optimum seal design between the lip force and the energy dissipation. The
rate of energy dissipation at the sealing lip is the limiting factor between success and failure of all lip seal designs.
10
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Lip Material Selection
The lip selection is generally based upon the operating temperature of the sealing lip, fluid compatibility, pressure in the
cavity, shaft speed, cost, operating environment and seal life requirement.
Note: Water resistance includes steam. No elastomeric material is ideally compatible with water as it is a very poor lubricant.
Good oil resistance. Low swell. Generally resistant to Fair wear properties. Poor dry running.
Polyacrylate
EP additives. Poor water resistance. May crack at low temperatures
Excellent oil and chemical resistance. Becomes stiff at low temperatures. Poor followability at
Fluoroelastomer
Good wear properties. Low swell. low temperatures.
Silicone Very wide temperature range Poor dry running properties. Poor resistance to oxidized
oil and some EP additives.
Excellent oil and chemical resistance. Easily damaged. Becomes stiff at low temperatures.
Teflon
Excellent temperature range. High cost. Poor followability at low temperatures.
Good temperature range. Good moisture Poor dry running characteristics. May have high swell
Ethylene Acrylic
resistance. Fair abrasion resistance. in some fluids.
11
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Lip Material Selection
Engine Oil SAE 30 Wt. Very good Very good Very good Very good
Engine Oil SAE 10 Wt. Very good Very good Good Very good
Gear Oil Super Gear Very good Very good Fair Very good
Gear Oil Hypoid Gear Good Good Poor Very good
Alcohol Very good Poor Good Fair
Amyl Naphthalene Poor Good Poor Very good
Automatic Transmission Fluid Very good Very good Fair Very good
Carbon Tetrachloride Fair Poor Poor Very good
Chrome Plating Solution Poor Poor Good Very good
Cutting Oil Very good Good Fair Very good
Detergent Solutions Very good Poor Very good Very good
Diesel Oil Very good Very good Poor Very good
Dry Cleaning Fluids Fair Poor Poor Very good
E.P. Lubricants Good Very good Poor Very good
Ethylene Glycol Very good Fair Very good Very good
Fuel Oil Very good Good Poor Good
Gasoline Fair Poor Poor Very good
Grease Very good Very good Very good Very good
Hydraulic Oil Very good Very good Fair Very good
Hydrochloric Acid Solution 20% Fair Fair Fair Very good
Isopropyl Alcohol Good Poor Very good Very good
Light Oil/Kerosene Fair Poor Poor Good
Linseed Oil Very good Very good Very good Very good
Machine Oil No. 2 Good Good Fair Very good
Methane Very good Very good Poor Good
Mineral Oil Very good Very good Good Very good
Naphtha Good Good Poor Very good
Paint Thinner, Duco Poor Poor Poor Good
Petroleum Base Lubricating Oil Very good Very good Fair Very good
SAE–90 Wt. Oil Very good Very good Poor Very good
Salt Water Very good Good Very good Very good
Soybean Oil Very good Very good Very good Very good
Sulfuric Acid Solution (30%) Fair Fair Poor Very good
Turbine Oil No. 2 Good Good Good Very good
Turpentine Very good Good Poor Very good
Water Very good Poor Very good Very good
Water–Glycol Very good Poor Good Fair
Xylene Poor Poor Poor Very good
12
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Lip Material Selection
Based Upon Shaft Speed
The following graph shows allowable shaft speeds relative to lip materials in non-pressure situations.
m/s Shaft - RPM
40
M
RPM
RPM
RPM
M
M
M
30,000 RP
RP
RP
RP
00
00
00
000
00
00
M M
6,0
RP
9,0
15,0
7,0
RP
8,0
M
10,
0
RP
00 ,50
M
35 0 3
RP
0
4,
50
00
4,
5,0
M
0 RP
30 3,00
SHAFT SURFACE SPEED m / s
PM
(Multiply m/s by 3.281 to get ft / s)
0 0R
25 2,5
Shaft - RPM
PM
0 0R
20 2,0
M
0 RP
15 1,50
RPM
10 1,000
NITRILES
500 RPM
5
0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200
SHAFT DIAMETER in mm
(Multiply mm by .03937 to get inches)
Example: 100mm diameter shaft, turning at 1500 RPM would be in the nitrile area.
i o n o r Design
Select
I N E S
H ELPL (800) 565
1
-12 4 0 • (918) 664-0
) 664-1146
7
0587
FAX: (918 m
kseals.co catalog.
www.clar s eals lis ted in this r i e nce , and
ited to the e
e is not lim od uct i o n & d e e o f s h a f t s e a l
s i g n ex p .
rodu c t lin
lark p
The C s o f p r an d t y p
45 year
more than ou with virtually a
n y s i ze
We have
vide y
we can pro
13
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Metal Case and Garter Spring Selection
The metal case and garter spring are important factors in the life of a seal. A carbon metal case is generally used in oil and
grease applications. In a corrosive environment, stainless steel is recommended. A rubber covered carbon steel metal case is
an economical substitute for stainless steel.
In a non–corrosive environment a carbon steel spring wire garter spring is generally used. Stainless steel is recommended in
corrosive environments or where the temperature of the lubricating fluid exceeds 270°F. (Carbon steel spring wire can be stress
relieved to reduce the cost of a stainless steel spring, but the reduction is small compared to the benefits.)
14
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Shaft Recommendations
Shaft and Seal Compatibility is dependent upon the shaft hardness, finish, tolerance and the lead–in chamfer.
Shaft Hardness is important in preventing excessive wear and developing scratches or dings during handling. It allows for
easy machining of the required finish. Under normal conditions, the sealing lip contact surface should be a Rockwell C–30. If
handling damage is likely to occur, then additional hardening to Rockwell C–45 is recommended. Harder surfaces are more
liable to “grain boundary corrosion” and if this is a risk, then corrosion–resistant coatings or stainless steel shaft sleeves are
used.
Shaft Surface Finish influences the amount of lip wear. The recommended roughness for a rotating shaft is 10 to 20 µin.
Ra (0.25 µm to 0.50 µm Ra) and for a reciprocating shaft, 5 to 10 µin. Ra (0.13 µm to 0.25 µm Ra). Ra is the roughness
average.
Plunge Grinding is recommended for a rotating shaft and centerless grinding is acceptable for a reciprocating shaft. The
rotating shaft finish must be free of machine leads as machine leads can pump fluid under the sealing lip. Hard chrome and
nickel plating can provide a hard surface and also prevent corrosion in harsh environments.
Shaft Tolerances are listed below. Shaft tolerances should be reduced for higher pressure and speed applications.
Shaft Diameter Tolerances Shaft Diameter Tolerances
in Inches in Millimeters
Shaft Chamfer free of burrs and sharp edges is required to prevent damage to the sealing lip or distortion resulting in a
dislodged garter spring.
typically Burr–free
15° ~ 25° rounded edges
Shaft D11
S.D.
15
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Shaft Recommendation
Shaft Eccentricity:
Measuring the shaft runout (TIR) and the shaft–to–bore misalignment determine eccentricity. Combine the two results for the
total eccentricity. The lip must follow the sealing surface to function effectively. As eccentricity and/or shaft speed increases, it
becomes more difficult for the lip to follow the sealing surface.
Shaft
de Bore centerline
Shaft centerline Center of rotation
rotation path
2de = TIR
Runout
Determine maximum total eccentricity by combining shaft runout (TIR) and shaft–to–bore misalignment (shaft offset) using the
method shown above.
(Multiply mm by .03937 to get inches)
0.40 0.40
SHAFT RUNOUT (mm)
0.30 0.30
SILICONE
0.20 0.20
0.10 0.10
16
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Housing Recommendations
Housings made of cast iron and steel provide good surfaces for both rubber covered and metal O.D. seals. Metal O.D. seals
are more suited for steel and cast iron housings where corrosion is not a factor. A metal O.D. seal has greater holding strength,
will not spring back after installation, and has better alignment and concentricity. Rubber O.D. seals are more suited for soft
alloy or plastic housings, for rough bore finishes above 100 µin. (2.54 µm) Ra, where corrosive conditions exist and in applica-
tions where the housing is subject to large thermal expansion. Rubber has a higher coefficient of thermal expansion than car-
bon steels and generally will tighten in the bore as temperature rises.
Housing bore chamfer is necessary to assist in the seal installation. A proper burr–free chamfer angle and depth minimizes
seal cocking or misalignment,, reduces installation forces, springback and seal case distortion.
0.005”
Max. R
15° ~ 30°
0.060” ~ 0.090”
Critical
must be
burr–free
Finish 125µ
in. or less
Bore Finish
The recommended specification for bore finish is 100 µin. (2.54 µm) Roughness Average (Ra) or less. If the bore is rougher
than 100 µin. (2.54 µm) Ra, then a rubber O.D. seal or an O.D. sealant is recommended. The bore roughness should never
exceed 125 µin. (3.15 µm) Ra.
i o n o r Design
Select
L I N E S
H E L P (800) 56 5 1
-12 4 0 • (918) 664
-00587
7
) 664-1146
FAX: (918 m
kseals.co catalog.
www.clar s eals lis ted in this r i e nce , and
ited to the e
e is not lim od uct i o n & d e e o f s h a f t s e a l
s i g n ex p .
rodu c t lin
lark p
The C s o f p r an d t y p
45 year
more than ou with virtually a
n y s i ze
We have
vide y
we can pro
17
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Housing Bore and Seal O.D. Tolerance
To ensure the proper fit between the bore and the seal, the following tolerances must be maintained.
Inch
Nominal Press–Fit Seal O.D. Tolerance (1) Seal O.D. Out of Round (2)
Millimeter
Nominal Press–Fit Seal O.D. Tolerance (1) Seal O.D. Out of Round (2)
n o r D esign
S electio
I N E S
H ELPL (800 ) 5 65 1
-12 40 • (918)
664-00587
) 664-1146
7
FAX: (918 com
kseals . log.
www.clar ls listed in this cata nce , and
ea
d to the s ex pe r i e
c t lin e is not limite uct i o n & d e s i g n f s h a f t s e a l .
produ
The Clark an 4 5 y e a r s o f n y s i ze a nd t y
p r od pe o
more th irtually
We have provide you with v
a
we can
18
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Installation Procedures
Installation tools are used to prevent lip damage and ensure the seal is properly aligned with the shaft. The tools are typi-
cally steel and are well designed for factory use. The outside diameter of the tools should be about 0.25 mm (0.010 in.) smaller
than the housing bore. The tool should always press near the seal O.D., which is usually the strongest section of the seal.
An arbor press is preferred for pressing the seal squarely into the bore. The sealing lips should be prelubricated with grease or
oil to reduce sliding friction of contact surfaces. This will also help protect the seal lips during initial run–in.
All double lipped seals should have grease packed between the two lips prior to installation. The excluder lip must have lubri-
cation and this is its only source. When two seals are installed in tandem, the space between the two seals must be filled with
grease and provision for relubrication provided.
When seals are adjacent to ball or tapered roller bearings, the original bearing design should incorporate appropriate channels
or holes in the housing for lubrication, as the bearing may create considerable pumping action during operation and adversely
affect sealing lip lubrication.
Caution: Do not damage or deform the sealing lip or metal case during installation.
Press–fitting tool
Installation tool
bottoms on shaft face. Keyway or splines
19
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
KB2 -0.125 -0.375 -0.230 V SCP -0.312 -0.750 -0.250 VC -0.312 -0.562 -0.125
TF -0.125 -0.624 -0.250 V TC -0.312 -0.750 -0.250 V SC -0.312 -0.625 -0.156
SC2P -0.156 -0.750 -0.246 SB -0.312 -0.751 -0.171 VB2 -0.312 -0.633 -0.140
TCU -0.156 -0.750 -0.246 VHP VB2 -0.312 -0.862 -0.250 VB2 -0.312 -0.686 -0.187
TC2P -0.156 -0.750 -0.246 V SC -0.312 -0.865 -0.250 TB2 -0.312 -0.749 -0.250
TC2P -0.156 -0.750 -0.246 SBR -0.312 -0.875 -0.250 SA2 -0.312 -0.750 -0.250
VC -0.157 -0.354 -0.118 KC -0.315 -0.472 -0.157 SC -0.312 -0.750 -0.250
SC2P -0.157 -0.750 -0.246 TC -0.315 -0.630 -0.236 P SC -0.312 -0.750 -0.250
TFU -0.157 -0.750 -0.309 V TC -0.315 -0.630 -0.276 SCP -0.312 -0.750 -0.250
TFU -0.157 -0.750 -0.309 SC -0.315 -0.630 -0.236 TC -0.312 -0.750 -0.250 V
TCUP -0.157 -0.750 -0.246 V SC -0.315 -0.708 -0.196 SB -0.312 -0.751 -0.171
TCUP -0.157 -0.750 0.246 V TC -0.315 -0.866 -0.275 VB2 -0.312 -0.862 -0.250
KC -0.171 -0.703 -0.235 V TC -0.354 -0.787 -0.276 SC -0.312 -0.865 -0.250
DKHR -0.181 -0.703 -0.235 V SC -0.354 -0.866 -0.276 SBR -0.312 -0.875 -0.250
VB -0.187 -0.501 -0.125 VC -0.372 -0.750 -0.250 KC -0.315 -0.472 -0.157
VC -0.187 -0.562 -0.094 VB -0.375 -0.562 -0.093 TC -0.315 -0.630 -0.236 P
TFH -0.187 -0.701 -0.204 V VB -0.375 -0.625 -0.125 TC -0.315 -0.630 -0.276
TFH -0.187 -0.701 -0.204 WPB -0.375 -0.625 -0.125 SC -0.315 -0.630 -0.236
SC -0.189 -0.866 -0.276 S VB -0.375 -0.687 -0.156 SC -0.315 -0.708 -0.196
VC -0.228 -0.500 -0.187 S SB2 -0.375 -0.749 -0.250 V TC -0.315 -0.866 -0.275
VC -0.236 -0.748 -0.275 SA2 -0.375 -0.750 -0.250 TC -0.354 -0.787 -0.276
VC -0.236 -0.394 -0.098 SB -0.375 -0.750 -0.250 SC -0.354 -0.866 -0.276
SC -0.250 -0.500 -0.250 SC -0.375 -0.750 -0.250 VC -0.372 -0.750 -0.250
VB -0.250 -0.500 -0.185 SC -0.375 -0.750 -0.250 VB -0.375 -0.562 -0.093
SB2 -0.250 -0.749 -0.250 TB2 -0.375 -0.750 -0.250 VC -0.375 -0.562 -0.125
SB2 -0.250 -0.749 -0.250 V VC -0.375 -0.817 -0.250 VB -0.375 -0.625 -0.125
SBR -0.250 -0.750 -0.250 SC -0.375 -0.875 -0.312 WPB -0.375 -0.625 -0.125
SC -0.250 -0.750 -0.250 SC -0.375 -0.875 -0.312 VB -0.375 -0.687 -0.156
SC2P -0.250 -1.000 -0.250 V KB2 0.125 -0.375 -0.230 V SB2 -0.375 -0.749 -0.250 V
TCP -0.250 -1.000 -0.250 V VC -0.157 -0.354 -0.118 SA2 -0.375 -0.750 -0.250
TCP -0.250 -1.000 -0.344 V VB -0.187 -0.501 -0.125 SB -0.375 -0.750 -0.250
DB3 -0.250 -1.000 -0.250 VL VC -0.187 -0.562 -0.094 SC -0.375 -0.750 -0.250
DB3 -0.250 -1.000 -0.500 VL SC -0.189 -0.866 -0.276 S SC -0.375 -0.750 -0.250
SB2 -0.250 -1.686 -0.375 VC -0.228 -0.500 -0.187 S TB2 -0.375 -0.750 -0.250
SB -0.281 -0.626 -0.250 P VC -0.236 -0.748 -0.275 VC -0.375 -0.817 -0.250
DF -0.308 -0.625 -0.250 VC -0.236 -0.394 -0.098 SC -0.375 -0.875 -0.312
SC -0.310 -0.563 -0.125 P SC -0.250 -0.500 -0.250 SC -0.375 -0.875 -0.312
VC -0.312 -0.499 -0.160 VB -0.250 -0.500 -0.185 WPH -0.312 -0.500 -0.125 P
VC -0.312 -0.499 -0.125 SB2 -0.250 -0.749 -0.250 VB2 -0.394 -0.874 -0.187 VL
VB -0.312 -0.500 -0.156 SB2 -0.250 -0.749 -0.250 V WPC -0.436 -0.625 -0.125
VB -0.312 -0.500 -0.100 SBR -0.250 -0.750 -0.250 CCT -0.440 -0.906 -0.372
WPC -0.312 -0.500 -0.125 SC -0.250 -0.750 -0.250 SC -0.472 -0.827 -0.157 V
VC -0.312 -0.562 -0.125 SB2 -0.250 -1.686 -0.375 VB -0.500 -0.750 -0.125
SC -0.312 -0.625 -0.156 SB -0.281 -0.626 -0.250 P VB2 -0.500 -0.750 -0.125 L
VB2 -0.312 -0.633 -0.140 SC -0.310 -0.563 -0.125 P VC -0.500 -0.750 -0.125
VB2 -0.312 -0.686 -0.187 VC -0.312 -0.499 -0.160 WPC -0.500 -0.750 -0.232
TB2 -0.312 -0.749 -0.250 VC -0.312 -0.499 -0.125 VB -0.500 -0.751 -0.125
SA2 -0.312 -0.750 -0.250 VB -0.312 -0.500 -0.156 SB -0.500 -0.801 -0.188
SC -0.312 -0.750 -0.250 VB -0.312 -0.500 -0.100 VB2 -0.500 -0.820 -0.156
SC -0.312 -0.750 -0.250 WPC -0.312 -0.500 -0.125 VB2 -0.500 -0.843 -0.250
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
20
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SC -0.500 -0.863 -0.187 SC -0.551 -0.984 -0.276 SB2 -0.625 -0.875 -0.188 L
SC -0.500 -0.871 -0.312 TB -0.551 -0.984 -0.276 SCY -0.625 -0.875 -0.156
SB -0.500 -0.875 -0.312 TC -0.551 -0.984 -0.276 VC -0.625 -0.875 -0.156
SB2 -0.500 -0.875 -0.188 L TC -0.551 -1.102 -0.276 WPB -0.625 -0.875 -0.125
SB2 -0.500 -0.875 -0.250 V SB2 -0.554 -0.999 -0.250 SCH -0.625 -0.875 -0.235
SC -0.500 -0.875 -0.250 P SB2 -0.562 -0.999 -0.250 V SB2 -0.625 -0.987 -0.250
SC -0.500 -0.875 -0.250 SB2 -0.562 -0.999 -0.250 SB2 -0.625 -0.999 -0.250
TB2 -0.500 -0.875 -0.250 V SCV -0.562 -0.941 -0.322 SC -0.625 -0.999 -0.250 P
TB2 -0.500 -0.875 -0.312 TB2 -0.562 -0.999 -0.250 SC -0.625 -0.999 -0.250
TC -0.500 -0.875 -0.250 SB -0.562 -1.000 -0.187 TB -0.625 -0.999 -0.250
SB -0.500 -0.999 -0.250 TB2 -0.562 -1.000 -0.250 TB2 -0.625 -0.999 -0.250 V
SB2 -0.500 -0.999 -0.250 V SB2 -0.562 -1.124 -0.250 V TB2 -0.625 -0.999 -0.250
SC -0.500 -0.999 -0.250 SC -0.562 -1.124 -0.312 SC -0.625 -1.000 -0.250
TA2 -0.500 -0.999 -0.375 TB2 -0.562 -1.124 -0.250 TC -0.625 -1.000 -0.250
TB2 -0.500 -0.999 -0.250 TB -0.562 -1.125 -0.250 VB -0.625 -1.000 -0.125
VB2 -0.500 -0.999 -0.250 SA2 -0.562 -1.246 -0.375 SCV -0.625 -1.016 -0.345
SB -0.500 -1.000 -0.250 P SA2 -0.562 -1.246 -0.375 VB -0.625 -1.062 -0.188
SB2 -0.500 -1.000 -0.250 TB2 -0.562 -1.250 -0.250 SB2 -0.625 -1.063 -0.250
TBRP -0.500 -1.000 -0.250 L SC -0.562 -1.375 -0.250 SB2 -0.625 -1.124 -0.250 V
TC -0.500 -1.000 -0.250 TB2 -0.562 -1.375 -0.250 TB -0.625 -1.124 -0.250
SB2 -0.500 -1.124 -0.250 TB -0.562 -1.378 -0.250 TB2 -0.625 -1.124 -0.250
SB2 -0.500 -1.124 -0.250 P TB -0.562 -1.558 -0.250 TB2 -0.625 -1.124 -0.250 V
SB2 -0.500 -1.124 -0.312 P TA2 -0.563 -1.125 -0.470 SC -0.625 -1.125 -0.250
SB2 -0.500 -1.124 -0.250 V VC -0.590 -0.750 -0.125 TB2 -0.625 -1.125 -0.250 L
SBR -0.500 -1.124 -0.250 TB -0.591 -0.787 -0.276 TB2 -0.625 -1.125 -0.250 L
SC -0.500 -1.124 -0.250 SC -0.591 -0.945 -0.197 TB2P -0.625 -1.125 -0.250 L
TB2 -0.500 -1.124 -0.250 TC -0.591 -0.945 -0.276 TC -0.625 -1.125 -0.313 V
TB2 -0.500 -1.124 -0.250 V SC -0.591 -0.984 -0.236 VB2 -0.625 -1.125 -0.250
VC -0.500 -1.124 -0.250 TC -0.591 -0.984 -0.236 SC -0.625 -1.128 -0.250
TB2 -0.500 -1.125 -0.250 L TC -0.591 -0.984 -0.276 SA2 -0.625 -1.246 -0.375
VB2 -0.500 -1.125 -0.250 VC -0.591 -0.984 -0.157 SB2 -0.625 -1.250 -0.250 V
VCVJ -0.500 -1.143 -0.400 TC -0.591 -1.004 -0.177 V SC -0.625 -1.250 -0.250
TB2 -0.500 -1.250 -0.250 TC -0.591 -1.024 -0.236 TB2 -0.625 -1.250 -0.250
TBRP -0.500 -1.250 -0.310 SSV TC -0.591 -1.102 -0.276 TBRP -0.625 -1.250 -0.250 VL
SC -0.500 -1.260 -0.250 SB -0.591 -1.181 -0.276 SB2 -0.625 -1.125 -0.250
SB2 -0.500 -1.375 -0.312 TC -0.591 -1.181 -0.276 TC -0.625 -1.250 -0.250
SB2 -0.500 -1.375 -0.250 V TC -0.591 -1.260 -0.276 TC -0.625 -1.125 -0.312
TB2 -0.500 -1.375 -0.312 TC -0.591 -1.378 -0.276 SBY -0.625 -2.132 -0.288
TB2 -0.500 -1.378 -0.406 TC -0.591 -1.378 -0.315 SB -0.625 -1.375 -0.312
SC -0.512 -0.866 -0.197 VB -0.593 -1.048 -0.187 SB2 -0.625 -1.375 -0.250 V
TB2 -0.531 -0.999 -0.250 S SB2 -0.593 -1.124 -0.312 SBR -0.625 -1.375 -0.250
TB2 -0.531 -1.124 -0.312 SC -0.593 -1.124 -0.250 TB -0.625 -1.375 -0.250
SB2 -0.531 -1.375 -0.250 TB2 -0.593 -1.124 -0.312 TB2 -0.625 -1.375 -0.250
SB2 -0.546 -0.875 -0.250 P TB2 -0.593 -1.250 -0.312 TB2 -0.625 -1.375 -0.250 V
VB2 -0.551 -1.124 -0.203 TB2 -0.593 -1.375 -0.312 TC -0.625 -1.375 -0.250
SC -0.551 -0.827 -0.157 TC -0.623 -1.125 -0.375 VB2 -0.625 -1.375 -0.250
SC -0.551 -0.945 -0.197 VB -0.625 -0.812 -0.093 SA2 -0.625 -1.377 -0.406
SC -0.551 -0.945 -0.236 VC -0.625 -0.812 -0.093 TA2 -0.625 -1.377 -0.250
TC -0.551 -0.945 -0.236 VC -0.625 -0.812 -0.093 P TB2 -0.625 -1.499 -0.250
SC -0.551 -0.984 -0.197 VBR -0.625 -0.812 -0.096 TB -0.625 -1.574 -0.312
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
21
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -0.625 -1.574 -0.312 SB -0.687 -0.999 -0.187 VB -0.750 -1.124 -0.156
TC -0.625 -1.574 -0.375 WPB -0.687 -0.999 -0.187 MC -0.750 -1.200 -0.093
SA2 -0.625 -1.624 -0.437 SB2 -0.687 -1.124 -0.250 SB2 -0.750 -1.249 -0.187 V
SBY -0.625 -2.132 -0.288 SB2 -0.687 -1.124 -0.250 V SA2 -0.750 -1.250 -0.375
SB2 -0.625 -0.875 -0.188 L TB -0.687 -1.124 -0.250 SB -0.750 -1.250 -0.250
TB -0.630 -1.024 -0.276 TB2 -0.687 -1.124 -0.250 SB2 -0.750 -1.250 -0.187 P
TC -0.630 -1.024 -0.276 SC -0.687 -1.125 -0.375 TB2 -0.750 -1.250 -0.250 L
TC -0.630 -1.102 -0.276 TC -0.687 -1.125 -0.250 SB2 -0.750 -1.250 -0.250
SC -0.630 -1.181 -0.276 VB2 -0.687 -1.187 -0.125 SB2 -0.750 -1.250 -0.250 V
TC -0.630 -1.181 -0.276 SB2 -0.687 -1.250 -0.312 V SB2 -0.750 -1.250 -0.250 B
TC -0.630 -1.181 -0.315 TB2 -0.687 -1.250 -0.250 SB2 -0.750 -1.250 -0.187
TC -0.630 -1.260 -0.276 SB2 -0.687 -1.375 -0.312 V SBR -0.750 -1.250 -0.250
WPB -0.634 -0.812 -0.160 SC -0.687 -1.375 -0.312 SC -0.750 -1.250 -0.250
SB2 -0.656 -1.124 -0.250 TB2 -0.687 -1.375 -0.250 SC -0.750 -1.250 -0.250 P
SB2 -0.656 -1.250 -0.250 VB -0.687 -1.375 -0.120 SC -0.750 -1.250 -0.250
SB -0.656 -1.375 -0.250 TB2 -0.687 -1.499 -0.312 SC -0.750 -1.250 -0.187
SB2 -0.656 -1.375 -0.250 VB2 -0.688 -0.919 -0.188 L TB -0.750 -1.250 -0.250
SB2 -0.656 -1.575 -0.250 VB2 -0.688 -0.999 -0.188 L TB2 -0.750 -1.250 -0.250
SC -0.656 -1.575 -0.250 SB -0.688 -1.062 -0.188 TB2 -0.750 -1.250 -0.250 V
TC -0.656 -1.575 -0.250 TC -0.688 -1.375 -0.313 TBR -0.750 -1.250 -0.250 L
SC -0.669 -0.984 -0.157 SC -0.709 -1.063 -0.236 TC -0.750 -1.250 -0.250
SC -0.669 -0.984 -0.197 TC -0.709 -1.102 -0.276 TR2 -0.750 -1.250 -0.250 V
SB2 -0.669 -0.999 -0.187 TC -0.709 -1.181 -0.315 VC -0.750 -1.250 -0.250
VC -0.669 -1.063 -0.118 TC -0.709 -1.181 -0.276 UTB2HJ -0.750 -1.125 -0.343
SB2 -0.669 -1.064 -0.250 SC -0.709 -1.260 -0.276 WPB -0.750 -1.250 -0.250
TC -0.669 -1.102 -0.236 TC -0.709 -1.260 -0.276 SB2 -0.750 -1.252 -0.187
TC -0.669 -1.102 -0.276 SC -0.709 -1.378 -0.276 SC -0.750 -1.252 -0.250
SB2 -0.669 -1.119 -0.235 TC -0.748 -1.260 -0.315 VB2 -0.750 -1.301 -0.250
SC -0.669 -1.142 -0.197 TC -0.748 -1.378 -0.315 SB2 -0.750 -1.312 -0.250
TC -0.669 -1.181 -0.315 TC -0.748 -1.378 -0.276 TB2 -0.750 -1.312 -0.250
TC -0.669 -1.181 -0.276 VB2 -0.750 -0.999 -0.125 SA2 -0.750 -1.375 -0.312
SB -0.669 -1.187 -0.187 VB -0.750 -1.000 -0.125 SB -0.750 -1.375 -0.250
SB2 -0.669 -1.187 -0.234 VB -0.750 -1.000 -0.125 SB2 -0.750 -1.375 -0.250 V
SB2 -0.669 -1.187 -0.185 VC -0.750 -1.000 -0.125 SC -0.750 -1.375 -0.250
SC -0.669 -1.187 -0.187 WPB -0.750 -1.000 -0.125 TB -0.750 -1.375 -0.250 V
VB -0.669 -1.250 -0.250 VB2 -0.750 -1.006 -0.125 TB2 -0.750 -1.375 -0.250 L
TC -0.669 -1.260 -0.315 WPC -0.750 -1.062 -0.181 TB2 -0.750 -1.375 -0.250 P
TC -0.669 -1.260 -0.276 SB -0.750 -1.124 -0.177 TB2 -0.750 -1.375 -0.250 V
TB2 -0.669 -1.375 -0.255 SB2 -0.750 -1.124 -0.187 V VB2 -0.750 -1.375 -0.250 P
TC -0.669 -1.378 -0.315 VB -0.750 -1.124 -0.156 SB2 -0.750 -1.499 -0.250
TC -0.669 -1.378 -0.276 WPB -0.750 -1.124 -0.187 SB2 -0.750 -1.499 -0.250 V
SB2 -0.669 -1.573 -0.280 V SB -0.750 -1.125 -0.187 SB2 -0.750 -1.499 -0.250
TC -0.669 -1.575 -0.276 SBR -0.750 -1.125 -0.188 TB2 -0.750 -1.499 -0.250
TC -0.669 -1.575 -0.315 SC -0.750 -1.125 -0.187 TC -0.750 -1.500 -0.250
SB2 -0.669 -1.181 -0.276 TB -0.750 -1.125 -0.250 TC -0.750 -1.500 -0.187
SB2 -0.670 -1.000 -0.188 L VB -0.750 -1.187 -0.156 TB2 -0.750 -1.500 -0.250 L
SB -0.672 -1.125 -0.187 VB2 -0.750 -1.187 -0.156 SA2 -0.750 -1.500 -0.390 L
SB -0.680 -1.373 -0.375 TB2 -0.750 -1.187 -0.250 TB2 -0.750 -1.503 -0.250 L
VB -0.687 -0.875 -0.093 TC -0.750 -1.187 -0.250 SA2 -0.750 -1.561 -0.375
WPB -0.687 -0.937 -0.125 MC -0.750 -1.187 -0.250 TB2 -0.750 -1.574 -0.312
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
22
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
23
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -0.875 -1.828 -0.375 TC -0.984 -1.457 -0.315 SC -1.000 -1.437 -0.250
TB2 -0.875 -1.874 -0.250 TC -0.984 -1.496 -0.276 TB2 -1.000 -1.437 -0.250
TB -0.875 -1.875 -0.250 TC -0.984 -1.496 -0.315 TB2 -1.000 -1.437 -0.250 V
TA2 -0.882 -2.088 -0.312 SB2 -0.984 -1.499 -0.250 V TC -1.000 -1.437 -0.250
TC -0.906 -1.654 -0.276 TB2 -0.984 -1.499 -0.250 SB2 -1.000 -1.496 -0.390
SA2 -0.906 -1.828 -0.437 TC -0.984 -1.499 -0.250 SB -1.000 -1.499 -0.312
TB2 -0.937 -1.375 -0.250 TC -0.984 -1.575 -0.315 SB2 -1.000 -1.499 -0.250
TB2 -0.937 -1.499 -0.250 TC -0.984 -1.575 -0.236 SB2 -1.000 -1.499 -0.250 P
TC -0.937 -1.499 -0.250 TC -0.984 -1.575 -0.276 SB2 -1.000 -1.499 -0.250
SB2 -0.937 -1.500 -0.250 V TC -0.984 -1.575 -0.276 SB2 -1.000 -1.499 -0.250
SB2 -0.937 -1.624 -0.250 V TC -0.984 -1.614 -0.276 SB2 -1.000 -1.499 -0.250 V
TB2 -0.937 -1.624 -0.250 TC -0.984 -1.654 -0.315 TB -1.000 -1.499 -0.250
VB2 -0.937 -1.734 -0.250 TC -0.984 -1.732 -0.276 TB2 -1.000 -1.499 -0.250
TB2 -0.937 -1.750 -0.312 TC -0.984 -1.772 -0.315 TB2 -1.000 -1.499 -0.250 L
SA2 -0.937 -1.828 -0.437 TC -0.984 -1.772 -0.394 TB2 -1.000 -1.499 -0.250 V
TC -0.937 -2.052 -0.312 TC -0.984 -1.772 -0.433 TC -1.000 -1.499 -0.250
TC -0.937 -2.052 -0.312 HP TC -0.984 -1.772 -0.354 SA2 -1.000 -1.500 -0.312
VC -0.938 -1.375 -0.254 V SA2 -0.984 -1.828 -0.437 SB2 -1.000 -1.500 -0.250 L
SB2 -0.938 -1.624 -0.250 L SB2 -0.984 -1.850 -0.250 TB2 -1.000 -1.500 -0.250
TC -0.938 -1.750 -0.312 TC -0.984 -1.850 -0.315 TB2 -1.000 -1.500 -0.312
TC -0.945 -1.378 -0.276 SC -0.984 -2.047 -0.250 TC -1.000 -1.500 -0.312
TC -0.945 -1.378 -0.315 SA2 -0.984 -2.062 -0.437 TC -1.000 -1.500 -0.375
TC -0.945 -1.575 -0.315 SC -0.984 -1.378 -0.197 TC -1.000 -1.500 -0.187
SC -0.945 -1.772 -0.276 TC -0.984 -1.378 -0.197 WPB -1.000 -1.500 -0.187
SB2 -0.950 -1.358 -0.275 P TC -0.984 -1.457 -0.236 SB -1.000 -1.562 -0.375 P
SA2 -0.968 -1.499 -0.312 TB2 -0.984 -1.499 -0.250 TB2 -1.000 -1.562 -0.250
SB2 -0.968 -1.499 -0.312 V SB2 -0.984 -1.575 -0.276 TB -1.000 -1.573 -0.312
SB2 -0.968 -1.624 -0.312 P SC -0.984 -1.850 -0.276 TB2 -1.000 -1.575 -0.312
SB2 -0.968 -1.624 -0.250 V TC -0.984 -1.850 -0.394 TB2 -1.000 -1.575 -0.250
TB2 -0.968 -1.624 -0.250 SC -0.984 -2.047 -0.276 VB2 -1.000 -1.575 -0.250
TB2 -0.968 -1.686 -0.312 VC -0.996 -1.540 -0.291 SB2 -1.000 -1.624 -0.250 V
TB2 -0.968 -1.752 -0.250 WPC -0.997 -1.250 -0.156 V TB2 -1.000 -1.624 -0.250 L
SB2 -0.968 -1.850 -0.375 VB -1.000 -1.250 -0.125 TB2 -1.000 -1.624 -0.250 V
SA2 -0.968 -1.828 -0.437 VB -1.000 -1.250 -0.125 L TC -1.000 -1.624 -0.250
SB2 -0.968 -1.850 -0.375 VB2 -1.000 -1.250 -0.125 TC -1.000 -1.624 -0.312
TB2 -0.968 -1.850 -0.312 VB2 -1.000 -1.250 -0.125 TC -1.000 -1.624 -0.312 P
TC -0.968 -1.850 -0.312 VC -1.000 -1.250 -0.125 VA2T -1.000 -1.625 -0.190 L
SA2 -0.968 -1.874 -0.437 WPB -1.000 -1.250 -0.125 SB2 -1.000 -1.625 -0.250
TC -0.968 -2.047 -0.375 WPC -1.000 -1.250 -0.125 YO -1.000 -1.688 -0.350 T
SB2 -0.968 -2.048 -0.375 VB -1.000 -1.312 -0.156 TB -1.000 -1.750 -0.250
SA2 -0.968 -2.062 -0.437 VB -1.000 -1.312 -0.125 TB -1.000 -1.750 -0.312
TC -0.969 -2.440 -0.250 VB2 -1.000 -1.312 -0.125 TB2 -1.000 -1.750 -0.313
TC -0.969 -2.440 -0.250 P SB2 -1.000 -1.365 -0.312 P TB2P -1.000 -1.752 -0.312 PL
TB2J -0.975 -1.500 -0.275 SSSUL SB2 -1.000 -1.375 -0.250 P TC -1.000 -1.750 -0.250
SB2 -0.984 -1.376 -0.312 V SB2 -1.000 -1.375 -0.250 V SB2 -1.000 -1.750 -0.250 L
SC -0.984 -1.378 -0.354 SC -1.000 -1.375 -0.188 SB2 -1.000 -1.752 -0.250 V
TC -0.984 -1.378 -0.276 TB -1.000 -1.375 -0.250 TB2 -1.000 -1.752 -0.250
TC -0.984 -1.378 -0.315 VB -1.000 -1.375 -0.187 P TB2 -1.000 -1.752 -0.250 V
TC -0.984 -1.417 -0.315 WPB -1.000 -1.375 -0.187 VB2 -1.000 -1.781 -0.469 L
SC -0.984 -1.457 -0.236 SB -1.000 -1.375 -0.250 V VB2Y -1.000 -1.781 -0.469
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
24
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SA2 -1.000 -1.828 -0.296 TC -1.062 -1.457 -0.276 WPB -1.125 -1.564 -0.250
SB2 -1.000 -1.828 -0.250 V SB2 -1.062 -1.499 -0.312 SB2 -1.125 -1.565 -0.250
SB2 -1.000 -1.828 -0.250 P SB2 -1.062 -1.499 -0.250 VB2 -1.125 -1.569 -0.197
SB2 -1.000 -1.752 -0.250 L WPB -1.062 -1.499 -0.187 TB2 -1.125 -1.575 -0.250
TB2P -1.000 -1.752 -0.312 LHP SA2 -1.062 -1.561 -0.375 KH -1.125 -1.624 -0.250
VB2H -1.000 -1.780 -0.250 L TB2 -1.062 -1.624 -0.250 SB2 -1.125 -1.624 -0.250 P
TB2 -1.000 -1.828 -0.250 TB2 -1.062 -1.625 -0.250 L TB2 -1.125 -1.624 -0.250 P
TC -1.000 -1.833 -0.250 TB2 -1.062 -1.752 -0.312 SB2 -1.125 -1.624 -0.250 V
SB2 -1.000 -1.851 -0.250 TB2 -1.062 -1.828 -0.375 SC -1.125 -1.624 -0.250 P
TC -1.000 -1.851 -0.250 SC -1.062 -1.850 -0.236 TB -1.125 -1.624 -0.250
SB -1.000 -1.874 -0.250 TB2 -1.062 -1.874 -0.250 TB2 -1.125 -1.624 -0.250
TB2 -1.000 -1.874 -0.250 SB2 -1.062 -1.875 -0.250 V TB2 -1.125 -1.624 -0.250 V
TC -1.000 -1.874 -0.250 SB2 -1.062 -1.979 -0.250 TB2 -1.125 -1.624 -0.250 L
VB2 -1.000 -1.938 -0.250 L TB2 -1.062 -1.980 -0.375 WPB -1.125 -1.624 -0.250
TC -1.000 -1.967 -0.250 SA2 -1.062 -1.983 -0.313 L KB2 -1.125 -1.625 -0.250
TC -1.000 -1.979 -0.250 SA2 -1.062 -1.983 -0.437 SB2 -1.125 -1.625 -0.312 S
TB2 -1.000 -1.980 -0.375 SB2 -1.062 -1.983 -0.250 SF -1.125 -1.625 -0.250 VHP
TC -1.000 -1.980 -0.375 SA2 -1.062 -1.996 -0.437 TB2 -1.125 -1.625 -0.250
TB2 -1.000 -1.983 -0.250 SA2 -1.062 -2.000 -0.437 TB2 -1.125 -1.625 -0.250 L
TB2 -1.000 -1.983 -0.250 V TB2 -1.062 -2.000 -0.375 TBR -1.125 -1.625 -0.500
SB2 -1.000 -2.000 -0.250 V TB2 -1.062 -2.062 -0.375 TC -1.125 -1.625 -0.250
SC -1.000 -2.000 -0.250 TB2 -1.062 -2.835 -0.375 TC -1.125 -1.686 -0.312
TB2 -1.000 -2.000 -0.250 SB2 -1.063 -1.500 -0.250 SB2 -1.125 -1.733 -0.375
TB2 -1.000 -2.000 -0.250 SA2 -1.093 -1.828 -0.437 SB2 -1.125 -1.752 -0.250
TB2 -1.000 -2.000 -0.250 V SA2 -1.093 -2.000 -0.437 TA2 -1.125 -1.752 -0.312
TC -1.000 -2.000 -0.500 TC -1.102 -1.496 -0.276 TB2 -1.125 -1.752 -0.250
TR2 -1.000 -2.000 -0.250 TC -1.102 -1.575 -0.315 TC -1.125 -1.752 -0.250
SB2 -1.000 -2.046 -0.250 V TC -1.102 -1.732 -0.276 KC -1.125 -1.778 -0.406
UKCHV -1.000 -2.000 -0.280 TC -1.102 -1.772 -0.394 TC -1.125 -1.780 -0.252
TFT -1.000 -2.000 -0.375 TC -1.102 -1.850 -0.315 TC -1.125 -1.781 0.406
TB2 -1.000 -2.441 -0.375 L TC -1.102 -2.047 -0.236 VB2 -1.125 -1.780 -0.468
KC3A2 -1.000 -2.441 -0.375 V VB -1.109 -1.502 -0.270 L TC -1.125 -1.781 -0.500
TB2 -1.000 -2.047 -0.250 VB -1.212 -1.504 -0.156 VB2 -1.125 -1.781 -0.250
TB2 -1.000 -2.047 -0.313 VB2 -1.122 -2.828 -0.250 VB2Y -1.125 -1.781 -0.468
TC -1.000 -2.047 -0.375 VB2 -1.125 -1.368 -0.125 B SB2 -1.125 -1.828 -0.250
SA2 -1.000 -2.062 -0.375 VB2 -1.125 -1.375 -0.125 V SC -1.125 -1.828 -0.312
SC -1.000 -2.062 -0.375 VC -1.125 -1.375 -0.125 P TB2 -1.125 -1.828 -0.312
VB2 -1.000 -2.250 -0.250 WPB -1.125 -1.375 -0.125 TB2 -1.125 -1.828 -0.250
TC -1.000 -2.312 -0.313 SB2 -1.125 -1.499 -0.187 TB2 -1.125 -1.828 -0.250 V
TB2 -1.000 -2.441 -0.375 KH -1.125 -1.499 -0.250 SC -1.125 -1.850 -0.312
TC -1.000 -2.441 -0.375 TC -1.125 -1.499 -0.250 SA2 -1.125 -1.851 -0.437
SC -1.024 -1.496 -0.197 KB2 -1.125 -1.500 -0.250 SB -1.125 -1.851 -0.437
TC -1.024 -1.496 -0.197 VBR -1.125 -1.500 -0.188 SB2 -1.125 -1.874 -0.250
TC -1.024 -1.496 -0.276 WPB -1.125 -1.500 -0.187 SB2 -1.125 -1.874 -0.250 V
TC -1.024 -1.575 -0.315 SA2 -1.125 -1.561 -0.375 SC -1.125 -1.874 -0.375
SC -1.024 -1.654 -0.315 SB2 -1.125 -1.561 -0.250 V TB2 -1.125 -1.874 -0.250
TB2 -1.031 -1.575 -0.312 WPB -1.125 -1.561 -0.250 TB2 -1.125 -1.874 -0.250 V
TC -1.031 -1.575 -0.312 SB -1.125 -1.563 -0.250 TC -1.125 -1.874 -0.250
SB2 -1.031 -1.624 -0.250 SB2 -1.125 -1.563 -0.250 SB2 -1.125 -1.875 -0.375 S
SC -1.062 -1.457 -0.276 VS -1.125 -1.564 -0.312 VC -1.125 -1.938 -0.187
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
25
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TC -1.125 -1.979 -0.250 SC -1.181 -2.165 -0.276 KB3 -1.240 -2.250 -0.312 V
TB2 -1.125 -1.983 -0.375 TC -1.181 -2.165 -0.433 VC -1.246 -1.748 -0.250
SB2 -1.125 -2.000 -0.250 V SC -1.181 -2.441 -0.276 VB -1.250 -1.500 -0.125
TB2 -1.125 -2.000 -0.250 TC -1.181 -2.441 -0.433 VC -1.250 -1.500 -0.156
TB2 -1.125 -2.000 -0.250 L SB2 -1.187 -1.561 -0.312 V WPB -1.250 -1.500 -0.125
TB2 -1.125 -2.000 -0.375 SB2 -1.187 -1.562 -0.250 VC -1.250 -1.580 -0.120
UTCH -1.125 -2.000 -0.500 TB2 -1.187 -1.752 -0.252 VB2 -1.250 -1.624 -0.250
TB2 -1.125 -2.047 -0.312 WPB -1.187 -1.562 -0.187 SB2 -1.250 -1.625 -0.187
TC -1.125 -2.047 -0.312 VC -1.187 -1.627 -0.250 WPB -1.250 -1.625 -0.250
TB2 -1.125 -2.062 -0.250 SB -1.187 -1.686 -0.375 SC -1.250 -1.686 -0.250 P
TB2 -1.125 -2.062 -0.250 V SB -1.187 -1.686 -0.375 L TC -1.250 -1.686 -0.218 V
SB2 -1.125 -2.125 -0.250 SB -1.187 -1.686 -0.250 P VB -1.250 -1.686 -0.250
SB2 -1.125 -2.125 -0.312 SB2 -1.187 -1.686 -0.250 P UB2 -1.250 -1.686 -0.187 L
SB2 -1.125 -2.125 -0.312 V TB2 -1.187 -1.686 -0.375 VC -1.250 -1.686 -0.250
TB2 -1.125 -2.125 -0.437 SB2 -1.187 -1.687 -0.250 WPB -1.250 -1.686 -0.187
TC -1.125 -2.125 -0.312 SB2 -1.187 -1.752 -0.250 V TB -1.250 -1.687 -0.312
SA2 -1.125 -2.250 -0.500 TB2 -1.187 -1.752 -0.250 TB2 -1.250 -1.687 -0.250 V
SA2 -1.125 -2.437 -0.468 TB2 -1.187 -1.752 -0.312 TB2 -1.250 -1.687 -0.312 L
TC -1.125 -2.440 -0.375 TB2 -1.187 -1.828 -0.375 TB2 -1.250 -1.687 -0.312
TB2 -1.125 -2.441 -0.375 VBR -1.187 -1.873 -0.250 TC -1.250 -1.687 -0.250
TB2 -1.125 -2.441 -0.375 L TB2 -1.187 -1.874 -0.250 TC -1.250 -1.687 -0.312
TC -1.125 -2.441 -0.312 SB -1.187 -1.686 -0.375 L VC -1.250 -1.748 -0.250
TB2 -1.125 -2.835 -0.375 VB -1.187 -1.874 -0.250 SC -1.250 -1.750 -0.250
SA2 -1.125 -2.875 -0.468 SB -1.187 -1.875 -0.250 P TB -1.250 -1.750 -0.312
TC -1.156 -1.575 -0.312 SB2 -1.187 -1.875 -0.250 p SB2R -1.250 -1.750 -0.250 L
SA2 -1.156 -1.686 -0.375 TB2 -1.187 -1.983 -0.375 SB2 -1.250 -1.752 -0.250 V
TB2 -1.156 -1.752 -0.312 P TB2 -1.187 -1.983 -0.250 TB -1.250 -1.752 -0.312
TB2 -1.156 -1.874 -0.250 TC -1.187 -1.983 -0.250 TB2 -1.250 -1.752 -0.250
TB2 -1.156 -1.984 -0.250 SB2 -1.187 -2.000 -0.250 SB2 -1.250 -1.752 -0.250 L
SA2 -1.156 -2.000 -0.437 SB2 -1.187 -2.000 -0.250 V TB2 -1.250 -1.752 -0.250 V
TB2 -1.156 -2.000 -0.312 TB2 -1.187 -2.000 -0.250 VB2Y -1.250 -1.752 -0.250
TB2 -1.156 -2.062 -0.375 SB2 -1.187 -2.062 -0.437 TB2 -1.250 -1.752 -0.312 V
TC -1.156 -2.062 -0.250 SB2 -1.187 -2.062 -0.250 WPB -1.250 -1.752 -0.250
SA2 -1.156 -2.125 -0.437 SB2 -1.187 -2.062 -0.250 P TH -1.250 -1.753 -0.250 P
VC -1.160 -1.562 -0.250 TB2 -1.187 -2.062 -0.250 SB2 -1.250 -1.874 -0.250 P
SA2 -1.170 -2.031 -0.375 TB2 -1.187 -2.125 -0.250 TB2 -1.250 -1.874 -0.250
VBR -1.181 -1.850 -0.237 SB2 -1.187 -2.165 -0.250 TB2 -1.250 -1.874 -0.250 V
TB -1.181 -1.575 -0.276 L SA2 -1.187 -2.250 -0.500 WPB -1.250 -1.874 -0.250
TC -1.181 -1.575 -0.276 SA2 -1.187 -2.437 -0.468 SC -1.250 -1.875 -0.250
SC -1.181 -1.654 -0.315 TB2 -1.187 -2.441 -0.375 TC -1.250 -1.875 -0.250
TC -1.181 -1.654 -0.315 TC -1.187 -2.441 -0.375 VB2 -1.250 -1.968 -0.437
SC -1.181 -1.732 -0.276 SB2 -1.187 -2.445 -0.468 TB2 -1.250 -1.979 -0.250 L
TC -1.181 -1.772 -0.315 SB2 -1.188 -2.441 -0.250 L TB2 -1.250 -1.979 -0.250
TC -1.181 -1.850 -0.236 VB -1.212 -1.504 -0.156 VB2 -1.250 -1.979 -0.250
SC -1.181 -1.890 -0.315 VB -1.213 -1.752 -0.250 VB2 -1.250 -1.979 -0.406
TC -1.181 -1.969 -0.433 VB2 -1.218 -1.979 -0.406 VB2 -1.250 -1.979 -0.250
TC -1.181 -1.969 -0.315 SA2 -1.218 -1.983 -0.437 SC -1.250 -1.980 -0.250
SC -1.181 -2.047 -0.276 VB2Y -1.218 -1.983 -0.250 SB2 -1.250 -1.983 -0.250
TC -1.181 -2.047 -0.433 SA2 -1.218 -2.000 -0.437 SB2 -1.250 -1.983 -0.250 V
TC -1.181 -2.047 -0.315 VB2 -1.220 -1.979 -0.250 TB2 -1.250 -1.983 -0.250
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
26
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -1.250 -1.983 -0.250 L SA2 -1.250 -3.155 -0.500 TB -1.250 -2.437 -0.312
VA -1.250 -1.983 -0.250 KC -1.254 -1.677 -0.150 TB2 -1.250 -2.437 -0.375
VA2 -1.250 -1.983 -0.250 VB2 -1.250 -1.968 -0.437 TC -1.250 -2.440 -0.312
SB2 -1.250 -2.000 -0.250 V KC3 -1.250 -1.978 -0.437 TB2 -1.250 -2.441 -0.375
SB2 -1.250 -2.000 -0.437 P TB2 -1.250 -1.979 -0.250 TB2 -1.250 -2.502 -0.375
SC -1.250 -2.000 -0.375 VB2 -1.250 -1.979 -0.250 SA2 -1.250 -2.561 -0.500
TA2 -1.250 -2.000 -0.437 VB2 -1.250 -1.979 -0.406 SB2 -1.250 -2.623 -0.250
TB2 -1.250 -2.000 -0.250 VB2 -1.250 -1.979 -0.250 SA2 -1.250 -2.713 -0.468
TB2 -1.250 -2.000 -0.437 VB21 -1.250 -1.979 -0.250 L SA2 -1.250 -2.835 -0.468
TB2 -1.250 -2.000 -0.250 V SC -1.250 -1.980 -0.250 TB2 -1.250 -2.835 -0.375
TB2 -1.250 -2.000 -0.256 SB2 -1.250 -1.983 -0.250 TC -1.250 -2.835 -0.375
TC -1.250 -2.000 -0.250 SB2 -1.250 -1.983 -0.250 V SA2 -1.250 -3.155 -0.500
TC -1.250 -2.000 -0.313 TB2 -1.250 -1.983 -0.250 KC -1.254 -1.677 -0.150
TC -1.250 -2.000 -0.437 VA -1.250 -1.983 -0.250 TB2 -1.281 -2.000 -0.375 L
DF -1.250 -2.040 -0.500 VA2 -1.250 -1.983 -0.250 UKCHV -1.280 -2.250 -0.280
SC -1.250 -2.062 -0.250 SB2 -1.250 -2.000 -0.250 V SBE -1.365 -1.900 -0.250 TFL
SC -1.250 -2.062 -0.437 SB2 -1.250 -2.000 -0.437 P MB20 -1.371 -2.525 -0.268 L
TB2 -1.250 -2.062 -0.250 SC -1.250 -2.000 -0.375 VF -1.375 -1.687 -0.187
TB2 -1.250 -2.062 -0.250 V TA2 -1.250 -2.000 -0.437 TH -1.375 -1.753 -0.250 P
SB2 -1.250 -2.125 -0.437 TA2 -1.250 -2.000 -0.450 VB2 -1.375 -1.874 -0.250
SB2 -1.250 -2.125 -0.250 V TB2 -1.250 -2.000 -0.250 VBR -1.375 -1.874 -0.156
SBR -1.250 -2.125 -0.437 TB2 -1.250 -2.000 -0.437 WPB -1.375 -1.874 -0.250
TB2 -1.250 -2.125 -0.250 TB2 -1.250 -2.000 -0.250 V SF -1.375 -1.875 -0.250 VHP
TB2 -1.250 -2.125 -0.250 TB2 -1.250 -2.000 -0.256 SC -1.375 -1.875 -0.312 P
TC -1.250 -2.125 -0.250 TC -1.250 -2.000 -0.250 TB2 -1.375 -1.938 -0.250
TC -1.250 -2.240 -0.252 TC -1.250 -2.000 -0.313 SB2 -1.375 -1.983 -0.312 P
SA2 -1.250 -2.250 -0.500 TC -1.250 -2.000 -0.437 SA2 -1.375 -2.000 -0.312
SB2 -1.250 -2.251 -0.375 UTCH -1.250 -2.000 -0.500 SB2 -1.375 -2.000 -0.312 V
TB2 -1.250 -2.252 -0.375 L SC -1.250 -2.062 -0.250 SC -1.375 -2.000 -0.312 P
TB2 -1.250 -2.252 -0.375 SC -1.250 -2.062 -0.437 SC -1.375 -2.000 -0.375
SB2 -1.250 -2.327 -0.500 TB2 -1.250 -2.062 -0.250 TB -1.375 -2.000 -0.312
TB2 -1.250 -2.328 -0.437 TB2 -1.250 -2.062 -0.250 V TB -1.375 -2.000 -0.437
TB2 -1.250 -2.328 -0.468 SB2 -1.250 -2.125 -0.437 TB2 -1.375 -2.000 -0.312 P
VB2Y -1.250 -2.328 -0.500 SB2 -1.250 -2.125 -0.250 V TB2 -1.375 -2.000 -0.312
SB2 -1.250 -2.374 -0.312 V SBR -1.250 -2.125 -0.437 TFT -1.375 -2.000 -0.375
TB2 -1.250 -2.374 -0.375 TB2 -1.250 -2.125 -0.250 TB2 -1.375 -2.000 -0.437
TB2 -1.250 -2.374 -0.312 TB2 -1.250 -2.125 -0.250 TB2 -1.375 -2.000 -0.312 V
TB -1.250 -2.437 -0.312 TC -1.250 -2.125 -0.250 TC -1.375 -2.000 -0.313
TB2 -1.250 -2.437 -0.375 TC -1.250 -2.240 -0.252 TCTH -1.375 -2.000 -0.375
TB2 -1.250 -2.440 -0.375 V SA2 -1.250 -2.250 -0.500 TB2 -1.375 -2.004 -312.000 VL
TC -1.250 -2.440 -0.312 SB2 -1.250 -2.251 -0.375 SB2 -1.375 -2.062 -0.312 V
TB2 -1.250 -2.441 -0.375 TB2 -1.250 -2.252 -0.375 TB2 -1.375 -2.062 -0.375
TB2 -1.250 -2.502 -0.375 SB2 -1.250 -2.327 -0.500 TB2 -1.375 -2.062 -0.312 P
SA2 -1.250 -2.561 -0.500 TB2 -1.250 -2.328 -0.437 TB2 -1.375 -2.106 -0.312
SB2 -1.250 -2.623 -0.250 TB2 -1.250 -2.328 -0.468 VB2Y -1.375 -2.106 -0.250
SA2 -1.250 -2.690 -0.312 L VB2Y -1.250 -2.328 -0.500 SA2 -1.375 -2.125 -0.437
SA2 -1.250 -2.713 -0.468 VB2H1 -1.250 -2.330 -0.500 L SB -1.375 -2.125 -0.375
SA2 -1.250 -2.835 -0.468 SB2 -1.250 -2.374 -0.312 V SB -1.375 -2.125 -0.315 S
TB2 -1.250 -2.835 -0.375 TB2 -1.250 -2.374 -0.375 SB2 -1.375 -2.125 -0.312 V
TC -1.250 -2.835 -0.375 TB2 -1.250 -2.374 -0.312 SC -1.375 -2.125 -0.437
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
27
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -1.375 -2.125 -0.312 TA2 -1.375 -3.000 -0.500 TB2 -1.437 -2.502 -0.312
TB2 -1.375 -2.125 -0.312 L SA2 -1.375 -3.125 -0.500 TB2 -1.437 -2.502 -0.312 L
TB2 -1.375 -2.125 -0.312 V TB2 -1.375 -3.150 -0.375 TB2 -1.437 -2.623 -0.375
TB2 -1.375 -2.125 -0.437 TC -1.375 -3.150 -0.375 TB2 -1.437 -2.686 -0.375
TC -1.375 -2.125 -0.312 SA2 -1.375 -3.350 -0.468 TB2 -1.437 -2.375 -0.312
TH -1.375 -2.375 -0.375 P TB2 -1.378 -1.851 -0.276 VL SA2 -1.437 -2.750 -0.500
TB2 -1.375 -2.441 -0.374 L TC -1.378 -1.772 -0.315 TB2 -1.468 -2.375 -0.375
TB2 -1.375 -2.441 -0.375 TC -1.378 -1.850 -0.276 TB2 -1.468 -2.437 -0.375
TB2 -1.375 -2.441 -0.375 VL TC -1.378 -1.890 -0.315 SB2 -1.484 -2.254 -0.312
TB2 -1.375 -2.441 -0.375 L TC -1.378 -1.969 -0.315 TB2 -1.487 -2.436 -0.375
SB2 -1.375 -2.250 -0.312 TB2 -1.378 -2.047 -0.315 P VB2 -1.490 -2.000 -0.250 VL
SB2 -1.375 -2.250 -0.312 V TC -1.378 -2.047 -0.354 SB2 -1.494 -2.060 -0.270
TB -1.375 -2.250 -0.500 TC -1.378 -2.047 -0.315 TC -1.496 -1.969 -0.315
TB -1.375 -2.250 -0.312 TC -1.378 -2.165 -0.315 TC -1.496 -1.969 -0.276
TB2 -1.375 -2.250 -0.312 TC -1.378 -2.165 -0.433 TC -1.496 -2.047 -0.354
TB2 -1.375 -2.250 -0.312 V TC -1.378 -2.165 -0.433 TC -1.496 -2.165 -0.315
TB2 -1.375 -2.250 -0.500 TC -1.378 -2.362 -0.472 TC -1.496 -2.165 -0.354
TB2 -1.375 -2.250 -0.312 L TC -1.378 -2.441 -0.394 TC -1.496 -2.283 -0.433
TC -1.375 -2.250 -0.312 TC -1.378 -2.756 -0.394 TB2 -1.500 -2.125 -0.437
SA2 -1.375 -2.350 -0.468 SB2 -1.378 -2.835 -0.315 V VB2 -1.500 -1.874 -0.187 V
SB2 -1.375 -2.374 -0.312 V SC -1.378 -2.835 -0.394 SB2 -1.500 -1.874 -0.250
TB2 -1.375 -2.374 -0.312 TC -1.378 -2.835 -0.472 SB2 -1.500 -1.874 -0.250 SS
TC -1.375 -2.374 -0.375 P TC -1.378 -3.150 -0.394 WPB2 -1.500 -1.875 -0.235
TC -1.375 -2.375 -0.312 SB2 -1.378 -3.346 -0.394 WPB -1.500 -1.874 -0.250
TB2 -1.375 -2.004 -0.312 L SB2 -1.378 -3.346 -0.394 KB -1.500 -1.875 -0.187
TB2 -1.375 -2.004 -0.312 VL TB2 -1.378 -2.835 -0.312 V VB -1.500 -1.875 -0.250
TB2 -1.375 -2.437 -0.375 SB2W -1.399 -2.292 -0.460 WPB -1.500 -1.875 -0.187
TB2 -1.375 -2.441 -0.312 TB2W -1.400 -2.292 -0.500 L SB2 -1.500 -1.918 -0.250 V
TB2 -1.375 -2.441 -0.375 TC -1.417 -1.929 -0.276 VB2 -1.500 -1.979 -0.256 L
TB2 -1.375 -2.441 -0.375 L TC -1.417 -2.047 -0.276 SA2 -1.500 -1.983 -0.437
TB2 -1.375 -2.441 -0.375 VL TC -1.417 -3.150 -0.394 TB2 -1.500 -1.983 -0.250 L
SB2 -1.375 -2.502 -0.312 V VF -1.421 -2.130 -0.187 SB2 -1.500 -1.983 -0.250
TB2 -1.375 -2.502 -0.375 VC -1.436 -2.062 -0.250 SB2 -1.500 -1.983 -0.250 V
TBR -1.375 -2.502 -0.375 TC -1.437 -1.875 -0.250 VB -1.500 -1.983 -0.187
TB2 -1.375 -2.562 -0.375 VC -1.437 -2.000 -0.125 SBR -1.500 -2.000 -0.250
TB2 -1.375 -2.562 -0.375 V SB2 -1.437 -2.062 -0.312 V SC -1.500 -2.000 -0.250
TB2 -1.375 -2.623 -0.375 SC -1.437 -2.062 -0.250 KC -1.500 -2.000 -0.250 P
SA2 -1.375 -2.686 -0.500 SC -1.437 -2.062 -0.250 KC -1.500 -2.000 -0.250
SA2 -1.375 -2.716 -0.468 TB2 -1.437 -2.062 -0.312 L SB -1.500 -2.000 -0.313
TC -1.375 -2.717 -0.375 SB2 -1.437 -2.081 -0.315 SB2 -1.500 -2.000 -0.312
SA2 -1.375 -2.750 -0.500 TB2 -1.437 -2.125 -0.312 SB2 -1.500 -2.000 -0.312 V
TA2 -1.375 -2.812 -0.375 TB2 -1.437 -2.125 -0.312 V TB2 -1.500 -2.000 -0.312 L
SB2 -1.375 -2.835 -0.312 P VC -1.437 -2.192 -0.250 SC -1.500 -2.000 -0.250
TB -1.375 -2.835 -0.468 SB2 -1.437 -2.250 -0.312 V TB2 -1.500 -2.000 -0.312
TB2 -1.375 -2.835 -0.312 P TB2 -1.437 -2.250 -0.312 L TC -1.500 -2.000 -0.313
TB2 -1.375 -2.835 -0.375 TB2 -1.437 -2.250 -0.312 V WPB2 -1.500 -2.000 -0.235
TB2 -1.375 -2.835 -0.375 L VB2 -1.437 -2.250 -0.250 WPB -1.500 -2.000 -0.250
TB2 -1.375 -2.835 -0.312 TB2 -1.437 -2.312 -0.375 WPC -1.500 -2.000 -0.187
TC -1.375 -2.835 -0.375 TB2 -1.437 -2.374 -0.312 SB2 -1.500 -2.062 -0.375
TB2 -1.375 -2.875 -0.312 P TB2 -1.437 -2.437 -0.468 SB2 -1.500 -2.062 -0.312
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
28
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SB2 -1.500 -2.062 -0.312 V SA2 -1.500 -2.441 -0.468 SA2 -1.562 -2.561 -0.500
SC -1.500 -2.062 -0.250 SB2 -1.500 -2.441 -0.312 V TB2 -1.562 -2.623 -0.312
TB -1.500 -2.062 -0.437 TA2 -1.500 -2.441 -0.468 TC -1.562 -2.623 -0.312
TB2 -1.500 -2.062 -0.437 TB2 -1.500 -2.441 -0.375 TB2 -1.562 -2.686 -0.375
VB2 -1.500 -2.062 -0.250 TB2 -1.500 -2.441 -0.312 VB2Y -1.562 -2.687 -0.250
SB2 -1.500 -2.125 -0.312 V SB2 -1.500 -2.501 -0.312 SA2 -1.562 -2.716 -0.468
SC -1.500 -2.125 -0.438 SB2 -1.500 -2.502 -0.312 V TB2 -1.562 -2.750 -0.375
TB -1.500 -2.125 -0.437 TA2 -1.500 -2.502 -0.500 SA2 -1.562 -2.758 -0.500
TB2 -1.500 -2.125 -0.437 TA2 -1.500 -2.502 -0.500 TB2 -1.562 -2.875 -0.375
TC -1.500 -2.125 -0.312 TB2 -1.500 -2.502 -0.312 L TB2 -1.562 -2.875 -0.312 P
TB2 -1.500 -2.125 -0.312 TB2 -1.500 -2.502 -0.312 TB2 -1.562 -2.875 -0.312 V
TB2 -1.500 -2.125 -0.312 V SB2 -1.500 -2.561 -0.312 TC -1.562 -3.150 -0.250
SB2 -1.500 -2.222 -0.375 TA2 -1.500 -2.561 -0.500 TC -1.562 -3.150 -0.312
SB2 -1.500 -2.250 -0.312 S TC -1.500 -2.562 -0.375 VB2 -1.563 -2.062 -0.200
SB2 -1.500 -2.250 -0.312 V SA2 -1.500 -2.623 -0.500 VB -1.563 -2.063 -0.203 L
TB -1.500 -2.250 -0.500 TB2HJ -1.500 -2.655 -0.437 L WPB -1.563 -2.062 -0.203
TB2 -1.500 -2.250 -0.312 TB2 -1.500 -2.686 -0.500 P TC -1.575 -2.047 -0.315
TB2 -1.500 -2.250 -0.312 V SA2 -1.500 -2.716 -0.468 TC -1.575 -2.047 -0.276
TB2 -1.500 -2.250 -0.500 L SB2 -1.500 -2.716 -0.437 TBR -1.575 -2.126 -0.315
TC -1.500 -2.250 -0.312 VB2Y -1.500 -2.716 -0.250 TC -1.575 -2.165 -0.315
SA2 -1.500 -2.254 -0.312 TBR -1.500 -2.721 -0.375 L TC -1.575 -2.205 -0.315
VB2 -1.500 -2.254 -0.250 TC -1.500 -2.721 -0.375 SB2 -1.575 -2.677 -0.312 L
VB2Y -1.500 -2.254 -0.250 TB2 -1.500 -2.750 -0.312 TC -1.575 -2.283 -0.315
TBR -1.500 -2.325 -0.437 TB2 -1.500 -2.758 -0.500 TC -1.575 -2.283 -0.394
VB2 -1.500 -2.327 -0.406 TB2 -1.500 -2.813 -0.312 SC -1.575 -2.362 -0.394
VB2Y -1.500 -2.327 -0.406 TB2 -1.500 -2.835 -0.468 TC -1.575 -2.362 -0.394
TB2 -1.500 -2.328 -0.500 SA2 -1.500 -2.875 -0.468 TC -1.575 -2.362 -0.472
TB2 -1.500 -2.374 -0.312 L SA2 -1.500 -2.996 -0.500 TC -1.575 -2.441 -0.472
TB2 -1.500 -2.375 -0.312 L TB2 -1.500 -3.000 -0.375 TC -1.575 -2.559 -0.394
KB2 -1.500 -2.375 -0.312 P TB2VJ -1.500 -3.160 -0.500 PL TC -1.575 -2.559 -0.472
KH -1.500 -2.375 -0.250 P TB2HJL -1.500 -2.360 -0.375 PL TC -1.575 -2.835 -0.394
TB2 -1.500 -2.375 -0.500 SA2 -1.531 -2.374 -0.375 TC -1.575 -3.150 -0.472
VB2H1 -1.500 -2.328 -0.390 TB2 -1.552 -2.502 -0.500 SB2 -1.575 -2.062 -0.230
VB2 -1.500 -2.328 -0.406 L TA2 -1.552 -2.750 -0.500 P TB2 -1.575 -2.062 -0.230
VB2 -1.500 -2.328 -0.406 SB2 -1.562 -2.062 -0.250 V SB2 -1.578 -2.082 -0.250
VB2 -1.500 -2.328 -0.500 SBR -1.562 -2.062 -0.250 SA2 -1.578 -2.408 -0.500
VB2Y -1.500 -2.328 -0.406 TA2 -1.562 -2.125 -0.437 SB2 -1.593 -2.125 -0.250
TB2HJ1 -1.500 -2.360 -0.375 PL TB2 -1.562 -2.125 -0.375 SA2 -1.593 -2.437 -0.468
SA2 -1.500 -2.374 -0.500 TB2 -1.562 -2.125 -0.312 P SB2 -1.593 -2.437 -0.312 P
SB2 -1.500 -2.374 -0.312 V TC -1.562 -2.125 -0.437 SB2 -1.593 -2.502 -0.250
TB2 -1.500 -2.374 -0.312 TB2 -1.562 -2.250 -0.312 SA2 -1.593 -2.623 -0.340
TB2 -1.500 -2.374 -0.312 V SA2 -1.562 -2.250 -0.375 SB2 -1.593 -2.623 -0.312
KC -1.500 -2.375 -0.250 SB2 -1.562 -2.374 -0.312 P SA2 -1.593 -2.758 -0.500
TB2 -1.500 -2.375 -0.312 TB2 -1.562 -2.374 -0.312 VC -1.609 -2.000 -0.250
TB2 -1.500 -2.375 -0.500 TB2 -1.562 -2.374 -0.312 V SBRW -1.618 -2.575 -0.500
TC -1.500 -2.375 -0.312 TB2 -1.562 -2.437 -0.375 TB2HJ -1.618 -2.841 -0.529 PL
TB2J1PL -1.500 -2.377 -0.470 TB2 -1.562 -2.441 -0.375 SB -1.620 -2.000 -0.266
TB2 -1.500 -2.377 -0.500 SB2 -1.562 -2.502 -0.312 V TB2 -1.625 -2.000 -0.250 VL
TB2 -1.500 -2.437 -0.375 TB2 -1.562 -2.502 -0.312 SB2 -1.625 -2.000 -0.250
WPB -1.500 -2.437 -0.250 WPB -1.562 -2.502 -0.250 SB -1.625 -2.000 -0.250
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
29
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
VS -1.625 -2.000 -0.187 VB2 -1.625 -2.781 -0.312 TB2 -1.687 -2.750 -0.375
WPB2 -1.625 -2.000 -0.235 SA2 -1.625 -2.835 -0.468 TB2 -1.687 -2.835 -0.468
VB2H -1.625 -2.000 -0.250 V TB2 -1.625 -2.875 -0.375 TA2 -1.687 -2.875 -0.468
SB2 -1.625 -2.116 -0.312 L SA2 -1.625 -2.996 -0.500 TB2 -1.687 -2.875 -0.375
TB2 -1.625 -2.116 -0.312 L SA2 -1.625 -3.000 -0.500 TB2 -1.687 -3.000 -0.375
SB -1.625 -2.125 -0.250 SA2 -1.625 -3.062 -0.500 SB2 -1.687 -3.061 -0.375
SB2 -1.625 -2.125 -0.250 P SA2 -1.625 -3.251 -0.500 TB2 -1.687 -3.062 -0.500
SB2 -1.625 -2.125 -0.250 V TB -1.654 -2.087 -0.315 TB2 -1.687 -3.125 -0.500
VB -1.625 -2.125 -0.250 TB -1.654 -2.165 -0.276 TB2 -1.687 -3.125 -0.375
VB2 -1.625 -2.125 -0.375 TC -1.654 -2.165 -0.315 SA2 -1.687 -3.189 -0.437
WPB -1.625 -2.125 -0.250 VB2 -1.654 -2.165 -0.236 VB -1.688 -2.375 -0.250
SB2 -1.625 -2.250 -0.375 P TC -1.654 -2.283 -0.276 SC -1.693 -2.126 -0.295
SB2 -1.625 -2.250 -0.312 V TC -1.654 -2.283 -0.315 TB2 -1.718 -2.561 -0.500
TC -1.625 -2.250 -0.312 TC -1.654 -2.362 -0.354 TB2 -1.719 -2.561 -0.500 L
TB2 -1.625 -2.250 -0.312 L TC -1.654 -2.441 -0.276 VA2 -1.718 -2.561 -0.500
TB2 -0.163 -2.250 -0.312 L TC -1.654 -2.559 -0.472 VB2 -1.718 -2.561 -0.500
TB2 -1.625 -2.250 -0.312 SB2 -1.654 -2.250 -0.220 SA2 -1.718 -2.623 -0.500
VB2HC1 -1.625 -2.328 -0.438 SA2 -1.656 -2.502 -0.500 TB -1.732 -2.441 -0.315
SA2 -1.625 -2.374 -0.500 SA2 -1.656 -2.686 -0.500 VB -1.735 -2.063 -0.240
SA2 -1.625 -2.374 -0.312 SB2 -1.656 -2.686 -0.312 TB2HJ -1.739 -2.812 -0.593 P
SB2 -1.625 -2.374 -0.312 V TB2 -1.656 -2.938 -0.375 TB2JR -1.748 -2.623 -0.330
SB2 -1.625 -2.374 -0.312 V SA2 -1.670 -2.686 -0.500 VC -1.750 -2.000 -0.109
SB2 -1.625 -2.374 -0.313 TB2 -1.684 -2.327 -0.530 SB -1.750 -2.125 -0.187
TB2 -1.625 -2.374 -0.312 TB2 -1.684 -2.562 -0.515 VB -1.750 -2.125 -0.187
TB2 -1.625 -2.374 -0.312 P SA2 -1.687 -2.279 -0.500 WPB -1.750 -2.125 -0.187
SA2 -1.625 -2.375 -0.312 L TB2HJ1 -1.687 -2.623 -0.437 P WPB -1.750 -2.125 -0.250
TA2 -1.625 -2.437 -0.468 TB2 -1.687 -2.328 -0.312 L SA2 -1.750 -2.250 -0.359
TB2 -1.625 -2.437 -0.375 VF -1.687 -2.378 -0.250 SB -1.750 -2.250 -0.312
TB2 -1.625 -2.437 -0.312 VB2 -1.687 -2.328 -0.500 SB2 -1.750 -2.250 -0.312 V
TB2 -1.625 -2.437 -0.312 TB2 -1.687 -2.374 -0.312 TB2 -1.750 -2.250 -0.374
TB2 -1.625 -2.441 -0.375 TB2 -1.687 -2.561 -0.500 L VB2 -1.750 -2.327 -0.312
TB2 -1.625 -2.441 -0.312 TFT -1.687 -2.875 -0.375 SB2 -1.750 -2.328 -0.437
MB2O -1.625 -2.462 -0.250 L TB2 -1.687 -2.750 -0.312 VC -1.750 -2.359 -0.484
TA2 -1.625 -2.502 -0.375 TB2 -1.687 -2.750 -0.312 L SB -1.750 -2.374 -0.437
TB2 -1.625 -2.502 -0.312 VF -1.687 -3.181 -0.187 TB2 -1.750 -2.374 -0.312
TB2 -1.625 -2.502 -0.312 P SB2 -1.687 -2.437 -0.250 S TB2 -1.750 -2.374 -0.312 L
TB2 -1.625 -2.502 -0.312 V SB2 -1.687 -2.437 -0.469 S TB2 -1.750 -2.374 -0.312 V
TC -1.625 -2.502 -0.312 TB2 -1.687 -2.437 -0.312 WPB -1.750 -2.374 -0.250
SB -1.625 -2.562 -0.500 TA2 -1.687 -2.500 -0.500 TC -1.750 -2.375 -0.312
TB2 -1.625 -2.562 -0.312 V TB2 -1.687 -2.502 -0.312 VC -1.750 -2.375 -0.312
TBR -1.625 -2.562 -0.312 TB2 -1.687 -2.502 -0.312 L SA2 -1.750 -2.411 -0.380 P
VA -1.625 -2.563 -0.250 VB2 -1.687 -2.502 -0.281 TA2 -1.750 -2.412 -0.468
SB2 -1.625 -2.623 -0.312 V VB2 -1.687 -2.562 -0.250 SB2 -1.750 -2.437 -0.312
TB2 -1.625 -2.623 -0.312 VB2Y -1.687 -2.562 -0.250 TB2 -1.750 -2.437 -0.312
SB2 -1.625 -2.686 -0.375 L TB2 -1.687 -2.623 -0.312 TB2 -1.750 -2.437 -0.312 V
SB2 -1.625 -2.686 -0.312 TB2 -1.687 -2.623 -0.500 TC -1.750 -2.437 -0.312
SA2 -1.625 -2.750 -0.312 TB2 -1.687 -2.623 -0.500 V TC -1.750 -2.437 -0.312 V
TB2 -1.625 -2.750 -0.375 TB2 -1.687 -2.686 -0.500 TB2 -1.750 -2.441 -0.375
TB2 -1.625 -2.750 -0.375 SA2 -1.687 -2.716 -0.468 SB2 -1.750 -2.441 -0.312
SA2 -1.625 -2.758 -0.500 TB2 -1.687 -2.750 -0.312 TB2HJ -1.739 -2.812 -0.593 P
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
30
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -1.750 -2.441 -0.375 V VB2Y -1.750 -2.997 -0.250 SA2 -1.781 -3.189 -0.437
VB2Y -1.750 -2.441 -0.250 SB -1.750 -3.000 -0.375 SB2 -1.804 -2.750 -0.312 PL
TB2 -1.750 -2.449 -0.312 SB2 -1.750 -3.000 -0.312 V SA2 -1.812 -2.437 -0.468
SB2 -1.750 -2.502 -0.312 V SB2 -1.750 -3.000 -0.375 TB2 -1.812 -2.562 -0.312 V
SB2 -1.750 -2.502 -0.375 S TB2 -1.750 -3.000 -0.375 TB2 -1.812 -2.623 -0.375
TA2 -1.750 -2.502 -0.375 V TB2 -1.750 -3.000 -0.312 TB2 -1.812 -2.686 -0.375
TB2 -1.750 -2.502 -0.312 TB2 -1.750 -3.061 -0.375 SA2 -1.812 -2.750 -0.500
TB2 -1.750 -2.502 -0.312 L TA2 -1.750 -3.189 -0.437 L TB2 -1.812 -2.750 -0.375
TB2 -1.750 -2.502 -0.312 V TB2 -1.750 -3.189 -0.437 TB2JTR -1.812 -2.778 -0.500 L
TB2 -1.750 -2.502 -0.312 VL TB2 -1.750 -3.189 -0.313 SB2 -1.812 -2.758 -0.500
TC -1.750 -2.502 -0.500 TB2 -1.750 -3.264 -0.500 TB2 -1.812 -2.875 -0.375
WPC -1.750 -2.502 -0.250 SA2 -1.750 -3.543 -0.500 TBJTR -1.812 -3.000 -0.500 VL
SB2 -1.750 -2.505 -0.375 TB2 -1.719 -2.561 -0.500 L SB2 -1.812 -3.125 -0.375
SA2 -1.750 -2.561 -0.500 TC -1.750 -2.375 -312.000 SA2 -1.812 -3.189 -0.437
TB2 -1.750 -2.561 -0.500 SB -1.750 -2.250 -0.312 VB2Y -1.843 -2.402 -0.234
VB2 -1.750 -2.561 -0.250 TB2 -1.750 -2.374 -0.312 L SC -1.843 -2.470 -0.244
TB2 -1.750 -2.565 -0.312 L VB2HC1 -1.750 -2.718 -0.359 TB2 -1.843 -2.502 -0.375
SA2 -1.750 -2.623 -0.375 TC -1.750 -2.750 -0.312 TB2 -1.843 -2.623 -0.375
SB2 -1.750 -2.623 -0.375 P TB2 -1.750 -3.937 -0.312 TB2 -1.843 -2.750 -0.375
SB2 -1.750 -2.623 -0.312 S TB2 -1.750 -2.441 -0.375 TB2 -1.843 -2.875 -0.375
TB2 -1.750 -2.623 -0.312 SB2 -1.750 -2.441 -0.312 SB2 -1.862 -2.361 -0.560
TB2 -1.750 -2.623 -0.312 V TBS -1.750 -2.502 -0.312 L SB2 -1.862 -2.562 -0.590
WPB -1.750 -2.623 -0.250 TB2 -1.750 -2.565 -0.312 L VB2 -1.865 -2.327 -0.312
TA2 -1.750 -2.625 -0.375 TB2 -1.750 -3.000 -0.375 TB2 -1.868 -2.518 -0.315 P
TA2 -1.750 -2.625 -0.500 TA2 -1.750 -3.189 -0.437 L SC -1.875 -2.390 -0.250
TC -1.750 -2.681 -0.438 SA2 -1.765 -2.412 -0.468 SC -1.875 -2.397 -0.250
SB2 -1.750 -2.686 -0.437 SB2 -1.765 -2.412 -0.375 SC -1.875 -2.397 -0.250
TB2 -1.750 -2.686 -0.375 VC -1.769 -2.561 -0.484 TC -1.875 -2.397 -0.250
SC -1.750 -2.688 -0.438 TC -1.772 -0.472 -0.472 SB2 -1.875 -2.398 -0.250 L
TC -1.750 -2.715 -0.437 TC -1.772 -2.165 -0.315 VB2 -1.875 -2.401 -0.272
MO -1.750 -2.716 -0.294 TB2 -1.772 -2.283 -0.354 VB2 -1.875 -2.401 -0.241
TB2 -1.750 -2.717 -0.437 TC -1.772 -2.362 -0.354 VC -1.875 -2.401 -0.275
VB2 -1.750 -2.718 -0.359 TC -1.772 -2.441 -0.354 TB2 -1.875 -2.470 -0.437
VB2Y -1.750 -2.718 -0.359 TC -1.772 -2.441 -0.276 TC -1.875 -2.471 -0.312
VB2 -1.750 -2.722 -0.359 TC -1.772 -2.559 -0.394 SC -1.875 -2.500 -0.315 S
SB2 -1.750 -2.750 -0.312 V TB -1.772 -2.677 -0.472 VC -1.875 -2.500 -0.315
SC -1.750 -2.750 -0.375 TC -1.772 -2.677 -0.472 TB2 -1.875 -2.502 -0.375
TB2 -1.750 -2.750 -0.312 TC -1.772 -2.756 -0.472 WPB -1.875 -2.502 -0.250
TC -1.750 -2.750 -0.312 VC -1.772 -2.756 -0.197 SC -1.875 -2.561 -0.312
VB2Y -1.750 -2.750 -0.484 TC -1.772 -2.835 -0.472 TB2 -1.875 -2.562 -0.312 V
SB2 -1.750 -2.756 -0.375 SC -1.772 -3.150 -0.394 V SB2 -1.875 -2.623 -0.312 V
SC -1.750 -2.756 -0.375 TC -1.772 -3.150 -0.394 TB -1.875 -2.623 -0.375
TB2 -1.750 -2.758 -0.375 SB2 -1.772 -3.346 -0.315 TB2 -1.875 -2.623 -0.312
TB2 -1.750 -2.810 -0.312 V TC -1.772 -3.346 -0.394 TB2 -1.875 -2.623 -0.312 V
SB2 -1.750 -2.875 -0.250 VB2 -1.781 -2.126 -0.250 TB2 -1.875 -2.686 -0.375
SB2 -1.750 -2.875 -0.312 V TC -1.781 -2.252 -0.375 SA -1.875 -2.750 -0.500
TA2 -1.750 -2.875 -0.375 SA2 -1.781 -2.502 -0.312 V SB2 -1.875 -2.750 -0.312 V
TB2 -1.750 -2.875 -0.375 SA2 -1.781 -2.686 -0.500 SB2 -1.875 -2.750 -0.312 P
TB2 -1.750 -2.996 -0.375 SA2 -1.781 -2.750 -0.500 TB2 -1.875 -2.750 -0.312
TA2 -1.750 -2.997 -0.312 SA2 -1.781 -2.758 -0.500 TB2 -1.875 -2.570 -0.312 L
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
31
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -1.875 -2.750 -0.375 TB2 -1.937 -2.750 -0.312 WPB -2.000 -2.502 -0.250
SA2 -1.875 -2.750 -0.500 SA2 -1.937 -2.758 -0.500 KB2P -2.000 -2.561 -0.250
SB2 -1.875 -2.758 -0.312 S SA2 -1.937 -2.875 -0.312 V SB2 -2.000 -2.561 -0.315
TB2 -1.875 -2.758 -0.375 TB2 -1.937 -2.875 -0.312 KB2J -2.000 -2.562 -0.220
SB2JR -1.875 -2.758 -0.425 P TB2 -1.937 -2.996 -0.375 TB2 -2.000 -2.623 -0.312
TA2 -1.875 -2.782 -0.500 TB2 -1.937 -3.000 -0.312 TB2 -2.000 -2.623 -0.312 V
TA2 -1.875 -2.782 -0.437 TB2 -1.937 -3.000 -0.312 V TC -2.000 -2.623 -0.313
TB2 -1.875 -2.835 -0.375 VB2Y -1.937 -3.000 -0.312 VB2Y -2.000 -2.623 -0.250 V
SB2 -1.875 -2.875 -0.312 TB2 -1.937 -3.061 -0.375 WPB -2.000 -2.623 -0.250
SB2 -1.875 -2.875 -0.312 V TB2 -1.937 -3.125 -0.375 SA2 -2.000 -2.627 -0.312 L
TB2 -1.875 -2.875 -0.312 L TB2 -1.937 -3.189 -0.437 KB2J -2.000 -2.632 -0.280
TB2 -1.875 -2.875 -0.312 TB2 -1.937 -3.251 -0.312 V VB2 -2.000 -2.635 -0.235
TB2 -1.875 -2.875 -0.312 V SA2 -1.937 -3.350 -0.468 TA2 -2.000 -2.686 -0.500
SA2 -1.875 -2.996 -0.500 TA2 -1.937 -3.350 -0.468 TB2 -2.000 -2.686 -0.437
SB2 -1.875 -3.000 -0.312 V TA2 -1.937 -3.543 -0.500 TB2 -2.000 -2.686 -0.375
TB2 -1.875 -3.000 -0.312 TA2 -1.937 -3.543 -0.375 TA2 -2.000 -2.686 -0.500
SB2 -1.875 -3.000 -0.313 L VA2T -1.938 -2.995 -0.200 L TB2 -2.000 -2.686 -0.500
TB2 -1.875 -3.000 -0.375 TB2 -1.938 -3.000 -0.312 SA2 -2.000 -2.713 -0.468
VA2 -1.875 -3.000 -0.250 KB2J -1.940 -2.500 -0.250 TB2 -2.000 -2.716 -0.468
VB2 -1.875 -3.000 -0.500 VB -1.950 -3.147 -0.250 TB2 -2.000 -2.716 -0.375
SB2 -1.875 -3.000 -0.375 SA2 -1.968 -2.686 -0.500 TC -2.000 -2.717 -0.563
TB2 -1.875 -3.061 -0.375 SA2 -1.968 -2.742 -0.500 P SB2 -2.000 -2.750 -0.312
TB2 -1.875 -3.125 -0.312 SA2 -1.968 -2.875 -0.468 SB2 -2.000 -2.750 -0.312 V
VB2Y -1.875 -3.150 -0.250 SA2 -1.968 -3.350 -0.468 TB2 -2.000 -2.750 -0.312 L
TB2WJ -1.875 -3.160 -0.695 PL TC -1.969 -3.543 -0.394 TB2 -2.000 -2.750 -0.375
TB2 -1.875 -3.189 -0.375 TC -1.969 -3.543 -0.472 TB2 -2.000 -2.750 -0.312 V
SA2 -1.875 -3.251 -0.500 TC -1.969 -2.441 -0.276 TC -2.000 -2.750 -0.312
TA2 -1.875 -3.371 -0.468 TC -1.969 -2.520 -0.315 VA -2.000 -2.750 -0.250
SB2 -1.875 -3.500 -0.437 TC -1.969 -2.559 -0.315 MO -2.000 -2.804 -0.300
TB2 -1.890 -2.441 -0.315 TC -1.969 -2.559 -0.354 TB2 -2.000 -2.835 -0.375
TC -1.890 -2.441 -0.276 TB2 -1.969 -2.623 -0.312 VB21 -2.000 -2.875 -0.250 L
TC -1.890 -2.559 -0.354 TB -1.969 -2.677 -0.276 SA2 -2.000 -2.875 -0.500
TC -1.890 -2.559 -0.394 TC -1.969 -2.756 -0.394 SB2 -2.000 -2.875 -0.312
TC -1.890 -2.756 -0.472 TC -1.969 -2.756 -0.472 SB2 -2.000 -2.875 -0.312 V
TB2HJ -1.900 -2.909 -0.437 P TC -1.969 -2.756 -0.354 TA2 -2.000 -2.875 -0.375
TB2 -1.929 -2.755 -0.265 TC -1.969 -2.835 -0.394 TB -2.000 -2.875 -0.312
SB2 -1.937 -2.437 -0.250 TC -1.969 -2.835 -0.472 TB2 -2.000 -2.875 -0.312
SB2 -1.937 -2.502 -0.375 TC -1.969 -2.835 -0.354 TB2 -2.000 -2.880 -0.312
TB2 -1.937 -2.561 -0.500 TC -1.969 -2.953 -0.472 TB2 -2.000 -2.880 -0.375
SB2 -1.937 -2.563 -0.312 SB -1.969 -3.150 -0.394 TB2 -2.000 -2.880 -0.375 P
TB2 -1.937 -2.623 -0.312 TB2 -1.980 -2.521 -0.312 SF -2.000 -2.843 -0.375 VHP
TB2 -1.937 -2.623 -0.312 V VF -1.991 -4.375 -0.187 VC -2.000 -2.889 -0.562
TC -1.937 -2.623 -0.312 VF -1.991 -4.387 -0.187 VB2Y -2.000 -2.962 -0.250
SB2 -1.937 -2.686 -0.375 S TBR -1.995 -3.345 -0.375 VB2 -2.000 -2.965 -0.312
SB2 -1.937 -2.686 -0.304 P VB -2.000 -2.371 -0.187 VB2 -2.000 -2.965 -0.500
TB2 -1.937 -2.686 -0.375 VB2 -2.000 -2.371 -0.250 TA2 -2.000 -2.996 -0.375 PL
TB2 -1.937 -2.686 -0.312 P VB -2.000 -2.375 -0.156 TC -2.000 -2.996 -0.312
TB2 -1.937 -2.686 -0.312 WPB -2.000 -2.375 -0.187 SA2 -2.000 -2.997 -0.375 V
TB2 -1.937 -2.686 -0.312 V SB2 -2.000 -2.500 -0.250 SB2 -2.000 -2.997 -0.375
SB2 -1.937 -2.750 -0.312 V SC -2.000 -2.502 -0.250 TA2 -2.000 -2.997 -0.375
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
32
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -2.000 -2.997 -0.375 TC -1.250 -1.687 -0.250 TA2 -2.125 -3.189 -0.468 S
TC -2.000 -2.997 -0.375 SB2R -1.250 -1.750 -0.250 L TB2 -2.125 -3.189 -0.375
SA2 -2.000 -3.000 -0.375 TC -1.250 -1.781 -0.406 TB2 -2.125 -3.189 -0.375
SA2 -2.000 -3.000 -0.375 V VB21 -1.250 -1.979 -0.250 L TB2 -2.125 -3.189 -0.375 V
TA2 -2.000 -3.000 -0.375 TB2 -1.125 -2.000 -0.250 L TB2 -2.125 -3.189 -0.469
TB2 -2.000 -3.000 -0.312 TB2 -1.125 -2.000 -0.250 TB2 -2.125 -3.250 -0.375 L
TB2 -2.000 -3.000 -0.312 V TA2 -1.250 -2.000 -0.450 TB2 -2.125 -3.251 -0.375
UTC4VJ -2.000 -3.000 -0.500 V VB2H1 -1.250 -2.330 -0.500 L TB2 -2.125 -3.251 -0.312
SA2 -2.000 -3.061 -0.500 SA2 -1.250 -2.690 -0.312 L TB2 -2.125 -3.264 -0.500
TA2 -2.000 -3.061 -0.500 TB2 -1.125 -2.441 -0.375 L TA2 -2.125 -3.350 -0.375
VB2 -2.000 -3.061 -0.250 TB2 -1.125 -2.441 -0.374 L KB -2.125 -3.371 -0.375
VB2Y -2.000 -3.061 -0.250 WPB -2.125 -2.500 -0.187 TA2 -2.125 -3.371 -0.375
TB2 -2.000 -3.062 -0.375 SB2 -2.125 -2.750 -0.375 V VB2 -2.125 -3.372 -0.375
TB2 -2.000 -3.125 -0.312 TB2 -2.125 -2.750 -0.375 TB2 -2.125 -3.350 -0.375
TA2 -2.000 -3.150 -0.375 TB2 -2.125 -2.750 -0.500 TA2 -2.125 -3.500 -0.375
VB2Y -2.000 -3.155 -0.500 SB2 -2.125 -2.763 -0.250 L TA2 -2.125 -3.543 -0.500
TA2 -2.000 -3.189 -0.468 SB2 -2.125 -2.763 -0.250 SA2 -2.125 -3.623 -0.468
TB2 -2.000 -3.189 -0.375 SA2 -2.125 -2.835 -0.468 SC -2.156 -2.875 -0.375
SB2 -2.000 -3.246 -0.500 TC -2.125 -2.871 -0.357 SA2 -2.156 -3.189 -0.437
TA2 -2.000 -3.251 -0.437 SA2 -2.125 -2.875 -0.375 SA2 -2.156 -3.251 -0.500
TA2 -2.000 -3.370 -0.468 SB2 -2.125 -2.875 -0.437 V TC -2.162 -3.544 -0.375
SA2 -2.000 -3.371 -0.468 SC -2.125 -2.875 -0.375 TB -2.165 -2.756 -0.709
SA2 -2.000 -3.371 -0.437 TA2 -2.125 -2.875 -0.437 TC -2.165 -3.346 -0.551
SB2 -2.000 -3.371 -0.437 V SA2 -2.125 -2.875 -0.437 SB2 -2.165 -3.937 -0.315
TA2 -2.000 -3.371 -0.437 SA2 -2.125 -2.875 -0.438 KB -2.180 -3.000 -0.500
TB2 -2.000 -3.371 -0.468 SB2 -2.125 -2.875 -0.438 L TB2 -2.187 -2.875 -0.375
TC -2.000 -3.371 -0.468 TB -2.125 -2.875 -0.438 TB2 -2.187 -2.875 -0.375
SA2 -2.000 -3.543 -0.500 TB2 -2.125 -2.875 -0.375 TB2 -2.187 -2.996 -0.375
TB -2.000 -3.625 -0.500 TB2 -2.125 -2.875 -0.437 SA2 -2.187 -3.000 -0.500
SB2 -2.062 -2.561 -0.312 V VB2 -2.125 -2.875 -0.250 TB2 -2.187 -3.000 -0.375
SA2 -2.062 -2.875 -0.437 VB -2.125 -2.891 -0.250 TB2 -2.187 -3.000 -0.375 V
TB2 -2.062 -2.996 -0.375 TB2 -2.125 -2.996 -0.375 TB2 -2.187 -3.062 -0.375
TB2 -2.062 -3.000 -0.375 TA2 -2.125 -2.997 -0.437 TB2 -2.187 -3.125 -0.375
TB2 -2.062 -3.000 -0.375 V TB3P -2.125 -3.000 -0.375 VHP TB2 -2.187 -3.189 -0.437
VB2 -2.062 -3.000 -0.312 SA2 -2.125 -3.000 -0.437 V TB2 -2.187 -3.251 -0.375
SA2 -2.062 -3.061 -0.500 SA2 -2.125 -3.000 -0.437 TB2 -2.187 -3.251 -0.312
SA2 -2.062 -3.125 -0.500 TA2 -2.125 -3.000 -0.437 TA2 -2.187 -3.350 -0.375
SB2 -2.062 -3.125 -0.375 TB -2.125 -3.000 -0.500 TA2 -2.187 -3.371 -0.375
TA2 -2.062 -3.190 -0.437 TB2 -2.125 -3.000 -0.375 TA2 -2.187 -3.500 -0.375
SA2 -2.062 -3.251 -0.500 TC -2.125 -3.000 -0.375 TA2 -2.187 -3.623 -0.468
SA2 -2.062 -3.623 -0.468 SA2 -2.125 -3.061 -0.437 V VB2 -2.240 -3.189 -0.610
SB2 -2.086 -2.679 -0.312 V TA2 -2.125 -3.061 -0.500 TC -2.244 -3.346 -0.472
VB2Y -2.093 -2.750 -0.250 TB2 -2.125 -3.061 -0.500 SB2 -2.248 -2.996 -0.500
VB2Y -2.093 -3.149 -0.546 TB2 -2.125 -3.061 -0.375 VB2 -2.250 -2.625 -0.187
VS -1.125 -1.564 -0.312 VB2Y -2.125 -3.061 -0.250 WPB -2.250 -2.625 -0.250
VB2 -1.250 -1.686 -0.187 L VC -2.125 -3.062 -0.475 WPB -2.250 -2.750 -0.250
TC -1.250 -1.875 -0.250 TA2 -2.125 -3.125 -0.437 P TB2 -2.250 -2.875 -0.312
TB2 -1.125 -1.624 -0.250 L TB2 -2.125 -3.125 -0.375 TB2 -2.250 -2.996 -0.437
TB2 -1.125 -1.625 -0.250 L VB2Y -2.125 -3.125 -0.437 TC -2.250 -2.996 -0.437
SF -1.125 -1.625 -0.250 V TB2 -2.125 -3.149 -0.375 TA2 -2.250 -2.997 -0.438
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
33
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SA2 -2.250 -3.000 -0.437 TA2 -2.250 -3.751 -0.500 TB2 -2.375 -3.251 -0.375
SA2 -2.250 -3.000 -0.437 V TB2 -2.250 -3.814 -0.250 SA2 -2.375 -3.350 -0.437
SB -2.250 -3.000 -0.375 SA2 -2.250 -3.875 -0.468 SB2 -2.375 -3.350 -0.375 P
SB2 -2.250 -3.000 -0.375 V TA2 -2.250 -4.003 -0.468 SB2 -2.375 -3.350 -0.375 S
TC -2.250 -3.000 -0.375 SC -2.252 -3.000 -0.375 TA2 -2.375 -3.350 -0.375
TA2 -2.250 -3.000 -0.437 VB2Y -2.281 -3.154 -0.375 TA2 -2.375 -3.350 -0.437
TB2 -2.250 -3.000 -0.375 VB2Y -2.293 -3.148 -0.359 TB2 -2.375 -3.350 -0.375
SB2 -2.250 -3.000 -0.375 SA2 -2.312 -3.000 -0.437 V TC -2.375 -3.500 -0.375
TB2 -2.250 -3.000 -0.375 V VB2 -2.312 -3.000 -0.380 SA2 -2.375 -3.371 -0.468
TA2 -2.250 -3.500 -0.438 L VB2 -2.312 -3.000 -0.250 SC -2.375 -3.371 -0.437
TA2 -2.250 -3.000 -0.438 L TB -2.312 -3.125 -0.375 P TA2 -2.375 -3.371 -0.375
UTC4VJ -2.250 -3.000 -0.500 TB2 -2.312 -3.125 -0.375 TB2 -2.375 -3.371 -0.468
TC -2.250 -3.000 -0.375 TB2 -2.312 -3.125 -0.375 V TC -2.375 -3.371 -0.437
SA2 -2.250 -3.061 -0.437 TB2 -2.312 -3.125 -0.375 V SA2 -2.375 -3.481 -0.400
TA2 -2.250 -3.061 -0.437 SA2 -2.312 -3.251 -0.500 TA2 -2.375 -3.481 -0.437
TA2 -2.250 -3.061 -0.437 S TA2 -2.312 -3.251 -0.375 SA2 -2.375 -3.500 -0.375
TB2 -2.250 -3.061 -0.375 TA2 -2.312 -3.251 -0.437 V SA2 -2.375 -3.500 -0.375 V
TC -2.250 -3.062 -0.375 TA2 -2.312 -3.350 -0.375 TA2 -2.375 -3.500 -0.375
SA2 -2.250 -3.125 -0.500 SA2 -2.312 -3.371 -0.468 TA2 -2.375 -3.500 -0.437
SA2 -2.250 -3.125 -0.437 TA2 -2.312 -3.374 -0.437 TB2 -2.375 -3.500 -0.375 P
SA2 -2.250 -3.125 -0.437 V SA2 -2.312 -3.500 -0.500 TC -2.375 -3.500 -0.375
TB2 -2.250 -3.125 -0.375 TA2 -2.312 -3.500 -0.375 TC -2.375 -3.500 -0.625
TB2 -2.250 -3.125 -0.375 SA2 -2.312 -3.751 -0.500 TA2 -2.375 -3.543 -0.375
TB2VM -2.250 -3.125 -0.625 V TC -2.362 -2.953 -0.354 TA2 -2.375 -3.543 -0.500
TB2 -2.250 -3.189 -0.437 TB -2.362 -3.031 -0.472 TA2 -2.375 -3.543 -0.437 V
TB2 -2.250 -3.189 -0.437 P TC -2.362 -3.071 -0.354 TA2 -2.375 -3.543 -0.312
SC -2.250 -3.250 -0.500 TC -2.362 -3.150 -0.394 VB2Y -2.375 -3.543 -0.250
TC -2.250 -3.250 -0.375 TC -2.362 -3.150 -0.472 SB2 -2.375 -3.623 -0.395
TC -2.250 -3.250 -0.750 P TC -2.362 -3.228 -0.472 TA2 -2.375 -3.623 -0.375
SA2 -2.250 -3.251 -0.375 TC -2.362 -3.346 -0.472 TA2 -2.375 -3.623 -0.437
SA2 -2.250 -3.251 -0.437 V SC -2.362 -3.740 -0.394 TA2 -2.375 -3.623 -0.437 V
TA2 -2.250 -3.251 -0.437 SC -2.362 -4.331 -0.472 TA2 -2.375 -3.751 -0.500
TB2 -2.250 -3.251 -0.375 TC -2.362 -4.331 -0.472 TA2 -2.375 -3.876 -0.375 L
TB2 -2.250 -3.251 -0.375 P SB2 -2.375 -2.997 -0.375 V VF -2.375 -4.381 -0.437
SA2 -2.250 -3.350 -0.437 V VB2H -2.375 -3.000 -0.250 SB2 -2.437 -3.125 -0.375
SB2 -2.250 -3.350 -0.375 P SB2 -2.375 -3.000 -0.375 V TB2 -2.437 -3.125 -0.375
TA2 -2.250 -3.350 -0.375 SA2 -2.375 -3.061 -0.437 TA2 -2.437 -3.251 -0.437
TA2 -2.250 -3.350 -0.437 SA2 -2.375 -3.061 -0.437 V TC -2.437 -3.251 -0.437
SA2 -2.250 -3.371 -0.437 V TB2 -2.375 -3.061 -0.375 TA2 -2.437 -3.350 -0.375
TA2 -2.250 -3.371 -0.437 SA2 -2.375 -3.125 -0.437 TB2 -2.437 -3.350 -0.375
TA2 -2.250 -3.371 -0.375 SA2 -2.375 -3.061 -0.438 L TA2 -2.437 -3.371 -0.375
TB2 -2.250 -3.371 -0.375 L TA2 -2.375 -3.125 -0.437 SA2 -2.437 -3.481 -0.500
VB2 -2.250 -3.371 -0.375 TA2 -2.375 -3.125 -0.437 V SA2 -2.437 -3.500 -0.437 V
TB2 -2.250 -3.481 -0.500 TB2 -2.375 -3.125 -0.375 TA2 -2.437 -3.500 -0.375
TA2 -2.250 -3.500 -0.375 TB2 -2.375 -3.189 -0.375 TA2 -2.437 -3.543 -0.375
TA2 -2.250 -3.500 -0.437 SB2 -2.375 -3.251 -0.437 P TA2 -2.437 -3.500 -0.438 L
SA2 -2.250 -3.623 -0.468 SB2 -2.375 -3.251 -0.375 P VA2T -2.450 -3.544 -0.200 L
TA2 -2.250 -3.623 -0.468 TCH 2.375 -3.251 -0.375 TC -2.480 -3.150 -0.354
TA2 -2.250 -3.623 -0.437 TA2 -2.375 -3.251 -0.375 TC -2.480 -3.346 -0.472
TB2 -2.250 -3.750 -0.500 TA2 -2.375 -3.251 -0.437 V WPB -2.500 -3.000 -0.250
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
34
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SA2 -2.500 -3.189 -0.437 V TB2 -2.500 -4.003 -0.375 TA2 -2.625 -3.751 -0.437 P
TB2 -2.500 -3.189 -0.375 L TB2 -2.500 -4.003 -0.375 V TB -2.625 -3.751 -0.375
SA2 -2.500 -3.245 -0.438 L TB2 -2.556 -3.937 -0.375 TB2 -2.625 -3.751 -0.375 L
TA2 -2.500 -3.247 -0.500 TC -2.559 -3.150 -0.472 UTB2HJW -2.625 -3.376 -0.700 VL
VB2HC -2.500 -3.250 -0.250 L SC -2.559 -3.346 -0.394 TA2 -2.625 -3.876 -0.468
TC -2.500 -3.250 -0.375 TC -2.559 -3.346 -0.472 SB2 -2.625 -4.003 -0.500
SB2 -2.500 -3.250 -0.500 VL TC -2.559 -3.465 -0.472 TA2 -2.625 -4.003 -0.375
SA2 -2.500 -3.251 -0.437 TC -2.559 -3.465 -0.315 TB2 -2.625 -4.003 -0.375
SA2 -2.500 -3.251 -0.437 V SC -2.559 -3.543 -0.394 TA2 -2.625 -4.249 -0.468
SB2 -2.500 -3.251 -0.500 V TC -2.559 -3.543 -0.472 SA2 -2.625 -4.438 -0.437
TA2 -2.500 -3.251 -0.437 TC -2.559 -3.543 -0.512 WPB -2.660 -3.250 -0.375
TB2 -2.500 -3.251 -0.375 TC -2.559 -5.512 -0.551 TC -2.677 -3.543 -0.472
TB2 -2.500 -3.251 -0.375 L SA2 -2.562 -3.250 -0.437 SA2 -2.687 -3.500 -0.500
TB2 -2.500 -3.251 -0.375 V TA2 -2.562 -3.481 -0.375 SA2 -2.687 -3.751 -0.500
TB2JW -2.500 -3.303 -0.465 TB2 -2.625 -3.500 -0.375 L SA2 -2.687 -3.876 -0.468
TA2 -2.500 -3.350 -0.468 TA2 -2.562 -3.500 -0.375 TBR -2.688 -3.750 -0.500
TA2 -2.500 -3.350 -0.437 SA2 -2.562 -3.543 -0.500 WPB -2.750 -3.125 -0.187
SA2 -2.500 -3.371 -0.500 S SA2 -2.562 -3.623 -0.375 SB2 -2.750 -3.481 -0.500
TA2 -2.500 -3.371 -0.437 V TB2 -2.562 -3.623 -0.468 P SA2 -2.750 -3.500 -0.437
TB2 -2.500 -3.371 -0.375 TA2 -2.562 -3.750 -0.375 SB2 -2.750 -3.500 -0.375
TB2 -2.500 -3.428 -0.375 SA2 -2.562 -3.876 -0.468 TA2 -2.750 -3.500 -0.375
TB2 -2.500 -3.428 -0.375 P TB2 -2.580 -3.876 -0.375 L TB2 -2.750 -3.500 -0.375 L
VB2HC -2.500 -3.500 -0.250 L SA2 -2.625 -3.250 -0.437 TB2 -2.750 -3.500 -0.375 V
SA2 -2.500 -3.500 -0.437 V SA2 -2.625 -3.350 -0.468 TBR -2.750 -3.500 -0.500
SA2 -2.500 -3.500 -0.437 P SB2 -2.625 -3.350 -0.375 V TC -2.750 -3.500 -0.375
SB2 -2.500 -3.500 -0.437 TB2 -2.625 -3.350 -0.375 VC -2.750 -3.500 -0.156
TA2 -2.500 -3.500 -0.500 TA2 -2.625 -3.371 -0.375 SA2 -2.750 -3.538 -0.437
TA2 -2.500 -3.500 -0.438 L TA2 -2.625 -3.374 -0.468 SA2 -2.750 -3.543 -0.437 V
TA2 -2.500 -3.500 -0.375 SA2 -2.625 -3.481 -0.500 TA2 -2.750 -3.543 -0.375
TA2 -2.500 -3.500 -0.437 SB2 -2.625 -3.500 -0.375 V TA2 -2.750 -3.543 -0.437 P
TA2 -2.500 -3.500 -0.437 V TA2 -2.625 -3.500 -0.375 TB2 -2.750 -3.545 -0.500 L
TB2 -2.500 -3.500 -0.375 V TA2 -2.625 -3.500 -0.437 SA2 -2.750 -3.623 -0.437 V
TB2 -2.500 -3.500 -0.437 TB2 -2.625 -3.500 -0.375 TA2 -2.750 -3.623 -0.375
TB2 -2.500 -3.500 -0.438 L TB2 -2.625 -3.500 -0.375 L TB2 -2.750 -3.623 -0.468
SB2 -2.500 -3.502 -0.406 S TB2 -2.625 -3.500 -0.437 P TA2 -2.750 -3.750 -0.375 L
TA2 -2.500 -3.543 -0.500 TA2 -2.625 -3.500 -0.438 L SA2 -2.750 -3.751 -0.437 V
TA2 -2.500 -3.543 -0.437 P UTCJW -2.625 -3.500 -0.700 V SB2 -2.750 -3.751 -0.437
TB2 -2.500 -3.543 -0.437 TA2 -2.625 -3.543 -0.375 TA2 -2.750 -3.751 -0.437
TC -2.500 -3.543 -0.438 SA2 -2.625 -3.623 -0.437 L TA2 -2.750 -3.751 -0.375
SA2 -2.500 -3.623 -0.437 SA2 -2.625 -3.623 -0.437 V TB2 -2.750 -3.751 -0.375
TA2 -2.500 -3.623 -0.375 SA2 -2.625 -3.623 -0.437 TB2 -2.750 -3.751 -0.437
TB2 -2.500 -3.623 -0.375 TA2 -2.625 -3.623 -0.437 TB2 -2.750 -3.751 -0.437 P
TB2 -2.500 -3.623 -0.375 V TA2 -2.625 -3.623 -0.375 WPB -2.750 -3.752 -0.375
TA2 -2.500 -3.750 -0.500 TA2 -2.625 -3.623 -0.438 L TC -2.750 -3.875 -0.375
SA2 -2.500 -3.751 -0.500 TB2 -2.625 -3.623 -0.375 TA2 -2.750 -3.876 -0.375
TB2 -2.500 -3.751 -0.437 TB2 -2.625 -3.623 -0.375 P TA2 -2.750 -3.876 -0.437 P
TA2 -2.500 -3.876 -0.468 TC -2.625 -3.750 -0.375 TA2 -2.750 -3.876 -0.437
TA2 -2.500 -3.876 -0.468 P SA2 -2.625 -3.751 -0.437 TB2 -2.750 -3.876 -0.437
TA2 -2.500 -3.881 -0.468 TA2 -2.625 -3.751 -0.375 TB2 -2.750 -3.937 -0.437 P
SA2 -2.500 -4.003 -0.468 TA2 -2.625 -3.751 -0.437 TA2 -2.750 -4.003 -0.375
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
35
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TA2 -2.750 -4.003 -0.437 P TA2 -2.937 -4.003 -0.375 SA2 -3.000 -4.003 -0.437 V
TB2 -2.750 -4.003 -0.375 V TB2 -2.937 -4.003 -0.437 PL TA2 -3.000 -4.003 -0.437
SB2 -2.750 -4.125 -0.437 TC -2.937 -4.003 -0.375 TA2 -3.000 -4.003 -0.437 P
TB2 -2.750 -4.125 -0.562 TA2 -2.937 -4.125 -0.375 TB2 -3.000 -4.003 -0.375
SB2 -2.750 -4.249 -0.625 TA2 -2.937 -4.250 -0.468 TB2 -3.000 -4.003 -0.375
TA2 -2.750 -4.249 -0.468 SA2 -2.937 -4.499 -0.468 TB2 -3.000 -4.003 -0.375 V
TA2 -2.750 -4.249 -0.437 P SB2 -2.938 -3.623 -0.375 TA2 -3.000 -4.125 -0.437
SC -2.756 -3.346 -0.315 SB2 -2.938 -3.623 -0.375 TA2 -3.000 -4.125 -0.437 V
TC -2.756 -3.543 -0.394 TB -2.938 -3.751 -0.375 TA2 -3.000 -4.249 -0.468 P
TC -2.756 -3.543 -0.472 TB2 -2.938 -3.751 -0.375 L TA2 -3.000 -4.249 -0.437 P
TB -2.756 -3.622 -0.472 TB2 -2.938 -3.751 -0.375 V TB2 -3.000 -4.250 -0.437 L
TC -2.756 -3.622 -0.472 TB2 -2.938 -3.751 -0.375 SA2 -3.000 -4.250 -0.625
TC -2.756 -3.740 -0.512 TB2 -2.938 -3.751 -0.375 V TA2 -3.000 -4.330 -0.500
SA2 -2.812 -3.751 -0.500 TA2 -2.938 -3.876 -0.375 V TA2 -3.000 -4.376 -0.500
TA2 -2.812 -3.876 -0.437 TA2 -2.938 -3.876 -0.375 V TA2 -3.000 -4.499 -0.468
TB2 -2.812 -3.876 -0.468 TB2 -2.938 -3.937 -0.437 P TA2 -3.000 -4.500 -0.437
TB2 -2.812 -4.003 -0.468 TB2 -2.938 -3.937 -0.437 P SA2 -3.000 -4.501 -0.437 V
SB2 -2.812 -4.249 -0.312 TA2 -2.938 -4.003 -0.437 SA2 -3.000 -4.875 -0.625
SC -2.835 -3.543 -0.394 TA2 -2.938 -4.003 -0.437 SA2 -3.000 -4.999 -0.468
SC -2.835 -3.740 -0.394 TB2 -2.938 -4.003 -0.437 P SC -3.040 -3.937 -0.250
SA2 -2.843 -3.939 -0.500 TB2 -2.938 -4.003 -0.437 P SA2 -3.062 -4.249 -0.625
TA2 -2.843 -3.939 -0.500 TC -2.953 -3.740 -0.472 SA2 -3.062 -4.999 -0.468
SA2 -2.843 -4.003 -0.500 V TB -2.953 -3.937 -0.512 VF -3.125 -3.875 -0.250
SA2 -2.843 -4.003 -0.437 TC -2.953 -3.937 -0.512 TC -3.125 -3.875 -0.250
TA2 -2.844 -3.944 -0.500 L TC -2.953 -4.134 -0.512 TA2 -3.125 -4.003 -0.375
TA2 -2.875 -3.623 -0.375 SB2 -3.000 -3.500 -0.375 V TA2 -3.125 -4.003 -0.375 V
SA2 -2.875 -3.751 -0.437 P WPB -3.000 -3.500 -0.250 TA2 -3.125 -4.003 -0.437
SA2 -2.875 -3.751 -0.437 V TC -3.000 -3.750 -0.375 SA2 -3.125 -4.125 -0.437
TA2 -2.875 -3.751 -0.438 L SA2 -3.000 -3.751 -0.437 TA2 -3.125 -4.125 -0.500
TA2 -2.875 -3.751 -0.375 SB2 -3.000 -3.751 -0.375 V TA2 -3.125 -4.125 -0.437 P
TA2 -2.875 -3.751 -0.437 TA2 -3.000 -3.751 -0.500 P TA2 -3.125 -4.125 -0.437 S
TA2 -2.875 -3.751 -0.437 V TA2 -3.000 -3.751 -0.437 TB2 -3.125 -4.125 -0.375 V
TA2 -2.875 -3.751 -0.438 VSSL TB2 -3.000 -3.751 -0.375 P TA2 -3.125 -4.249 -0.500
TB2 -2.875 -3.751 -0.375 V TB2 -3.000 -3.751 -0.375 TA2 -3.125 -4.249 -0.437
TA2 -2.875 -3.876 -0.375 TB2 -3.000 -3.751 -0.375 V TA2 -3.125 -4.249 -0.437 V
TA2 -2.875 -3.876 -0.437 TB2 -3.000 -3.875 -0.437 TA2 -3.125 -4.375 -0.500
TA2 -2.875 -3.876 -0.437 V SA2 -3.000 -3.876 -0.468 V TA2 -3.125 -4.376 -0.437 P
VB2Y -2.875 -3.876 -0.250 SB2 -3.000 -3.876 -0.312 V TA2 -3.125 -4.500 -0.500
SB -2.875 -4.000 -0.375 S SB2 -3.000 -3.876 -0.343 S TA2 -3.125 -4.626 -0.437
SB2 -2.875 -4.003 -0.375 TA2 -3.000 -3.876 -0.437 TA2 -3.125 -4.751 -0.500
SC -2.875 -4.003 -0.375 SA2 -3.000 -3.999 -0.437 TA2 -3.125 -4.999 -0.468
TA2 -2.875 -4.003 -0.375 PBSCE -3.000 -4.000 -0.500 VSS TA2 -3.125 -5.251 -0.468
TA2 -2.875 -4.003 -0.437 TC -3.000 -4.000 -0.500 TC -3.150 -3.937 -0.512
TB2 -2.875 -4.003 -0.375 V TC -3.000 -4.000 -0.437 TC -3.150 -3.937 -0.394
TA2 -2.875 -4.125 -0.375 SB2 -3.000 -4.003 -0.312 L TC -3.150 -3.937 -0.472
SA2 -2.875 -4.376 -0.625 SA2 -3.000 -4.003 -0.468 SC -3.150 -4.134 -0.394
SA2 -2.875 -4.499 -0.468 SA2 -3.000 -4.003 -0.437 TC -3.150 -4.134 -0.512
TA2 -2.937 -3.751 -0.375 TA2 -3.000 -4.003 -0.375 SC -3.150 -4.724 -0.512
TA2 -2.937 -3.876 -0.375 TA2 -3.000 -4.003 -0.375 L TC -3.150 -4.724 -0.512
TA2 -2.937 -3.937 -0.500 PL SA2 -3.000 -4.003 -0.375 P SA2 -3.187 -4.249 -0.468
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
36
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SA2 -3.187 -4.250 -0.625 TF3 -3.375 -3.948 -0.375 TB2 -3.500 -4.501 -0.375
SA2 -3.187 -4.269 -0.468 TB2 -3.375 -4.125 -0.375 V TA2 -3.500 -4.501 -0.486
TA2 -3.187 -4.376 -0.500 TA2 -3.375 -4.249 -0.500 TA2 -3.500 -4.501 -0.486 L
SA2 -3.187 -4.499 -0.468 TB2 -3.375 -4.280 -0.406 S UTB2HJW -3.500 -4.504 -0.725 V
SA2 -3.187 -4.999 -0.468 TB2 -3.375 -4.375 -0.375 L TA2 -3.500 -4.625 -0.500
VF -3.250 -3.623 -0.187 SA2 -3.375 -4.376 -0.437 SA2 -3.500 -4.751 -0.625
VBR -3.250 -3.625 -0.188 TA2 -3.375 -4.376 -0.437 TA2 -3.500 -4.751 -0.500
SC -3.250 -4.000 -0.437 TB2 -3.375 -4.376 -0.500 TA2 -3.500 -4.751 -0.437
TA2 -3.250 -4.003 -0.468 TB2 -3.375 -4.376 -0.375 TA2 -3.500 -4.751 -0.438 L
TB2 -3.250 -4.003 -0.375 P TB2 -3.375 -4.376 -0.375 V TB2 -3.500 -4.751 -0.375 V
SA2 -3.250 -4.125 -0.562 TA2 -3.375 -4.500 -0.500 TA2 -3.500 -4.875 -0.500
SA2 -3.250 -4.249 -0.437 P TC -3.375 -4.500 -0.500 UTCJW -3.500 -4.492 -0.725 VL
SA2 -3.250 -4.249 -0.437 TB2 -3.375 -4.501 -0.437 V UTCJW -3.500 -4.996 -0.717 VL
SA2 -3.250 -4.249 -0.437 V TA2 -3.375 -4.626 -0.500 TA3 -3.500 -4.499 -0.468 VL
TA2 -3.250 -4.249 -0.437 P TA2 -3.375 -4.626 -0.437 TA2 -3.500 -4.999 -0.468
TA2 -3.250 -4.249 -0.437 SA2 -3.375 -4.688 -0.500 TA2 -3.500 -4.999 -0.468 L
TB2 -3.250 -4.249 -0.500 TA2 -3.375 -4.751 -0.500 TA2 -3.500 -4.999 -0.437 P
TB2 -3.250 -4.249 -0.375 TB2 -3.375 -4.751 0.375 L TA3 -3.500 -4.999 -0.468 VL
TB2 -3.250 -4.249 -0.375 V TA2 -3.375 -4.999 -0.468 TB2 -3.500 -4.999 -0.437 V
TB2 -3.250 -4.250 -0.375 L TA2 -3.375 -4.999 -0.468 L UTB2HJW -3.500 -5.004 -0.725 V56L
SB2 -3.250 -4.250 -0.312 TB2 -3.375 -5.000 -0.468 P TA2 -3.500 -5.126 -0.500
TA2 -3.250 -4.250 -0.438 L TA2 -3.375 -5.250 -0.468 L TA2 -3.500 -5.126 -0.437
UTB2HJW -3.250 -4.250 -0.855 V56L TA2 -3.375 -5.251 -0.468 TA2 -3.500 -5.251 -0.468
TA2 -3.250 -4.376 -0.500 TA2 -3.375 -5.251 -0.437 TA2 -3.500 -5.500 -0.500
TA2 -3.250 -4.500 -0.500 TA2 -3.397 -4.999 -0.468 L SA2 -3.500 -5.751 -0.562
TB2 -3.250 -4.500 -0.437 P SA2 -3.437 -4.500 -0.625 SC -3.543 -4.331 -0.472
TB2 -3.250 -4.500 -0.500 TA2 -3.437 -4.501 -0.375 TC -3.543 -4.528 -0.512
SA2 -3.250 -4.501 -0.437 TA2 -3.437 -4.501 -0.437 TA2 -3.562 -4.499 -0.468
TA2 -3.250 -4.501 -0.437 TB2 -3.437 -4.501 -0.375 TA2 -3.562 -4.625 -0.500
TA2 -3.250 -4.626 -0.500 TA2 -3.437 -4.626 -0.500 TA2 -3.562 -4.751 -0.500
TA2 -3.250 -4.723 -0.468 TB2 -3.437 -4.751 -0.437 TA2 -3.562 -4.876 -0.500
SA2 -3.250 -4.751 -0.484 SA2 -3.437 -4.756 -0.562 SA2 -3.625 -4.375 -0.375 P
SA2 -3.250 -4.999 -0.468 TA2 -3.437 -4.876 -0.500 SA2 -3.625 -4.376 -0.375
TA2 -3.250 -4.999 -0.468 SA2 -3.437 -4.999 -0.468 TB2 -3.625 -4.376 -0.375 V
TA2 -3.250 -4.999 -0.437 SA2 -3.437 -4.999 -0.437 TB2 -3.625 -4.376 -0.375
TB2 -3.250 -5.000 -0.468 SA2 -3.437 -5.250 -0.468 TA2 -3.625 -4.499 -0.468
SA2 -3.250 -5.251 -0.468 VB2 -3.500 -4.003 -0.250 SB2 -3.625 -4.501 -0.375
SA2 -3.312 -4.125 -0.562 WPB -3.500 -4.003 -0.250 TA2 -3.625 -4.625 -0.500
TA2 -3.312 -4.249 -0.500 SA2 -3.500 -4.376 -0.437 SA2 -3.625 -4.626 -0.437
TA2 -3.312 -4.376 -0.500 TA2 -3.500 -4.376 -0.500 SB2 -3.625 -4.626 -0.500
TA2 -3.312 -4.499 -0.468 TA2 -3.500 -4.376 -0.437 SB2 -3.625 -4.626 -0.500 P
SA2 -3.312 -4.501 -0.468 TB2 -3.500 -4.376 -0.375 TA2 -3.625 -4.626 -0.437
TA2 -3.312 -4.751 -0.500 TB2 -3.500 -4.376 -0.375 V TB2 -3.625 -4.626 -0.375 V
SA2 -3.312 -4.999 -0.468 TA2 -3.500 -4.500 -0.438 L TA2 -3.625 -4.751 -0.625
TC -3.346 -4.331 -0.512 SA2 -3.500 -4.501 -0.437 TA2 -3.625 -4.751 -0.500
TC -3.346 -4.528 -0.512 SA2 -3.500 -4.501 -0.437 V TB2 -3.625 -4.751 -0.500 S
SC -3.346 -5.118 -0.472 TA2 -3.500 -4.501 -0.468 L SA2 -3.625 -4.839 -0.500
VC -3.375 -3.875 -0.375 TA2 -3.500 -4.501 -0.468 P TA2 -3.625 -4.875 -0.500
TC -3.375 -3.948 -0.375 TA2 -3.500 -4.501 -0.437 TA2 -3.625 -4.999 -0.500
TC -3.375 -3.948 -0.375 V TA2 -3.500 -4.501 -0.437 P TA2 -3.625 -4.999 -0.437
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
37
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TB2 -3.625 -4.999 -0.375 V TA2 -3.875 -4.876 -0.500 V TA2 -4.000 -5.501 -0.562
TB2 -3.625 -4.999 -0.375 TA2 -3.875 -4.999 -0.500 TA2 -4.000 -5.626 -0.375
TB2 -3.625 -5.000 -0.468 TB2 -3.875 -4.999 -0.375 TA2 -4.000 -5.751 -0.562
TA2 -3.625 -5.251 -0.437 TB2 -3.875 -4.999 -0.375 V TA2 -4.000 -5.999 -0.500
TA2 -3.625 -5.375 -0.500 TA2 -3.875 -5.125 -0.500 TA2 -4.000 -6.250 -0.500
TA2 -3.625 -5.501 -0.500 TA2 -3.875 -5.126 -0.437 V SA2 -4.061 -5.501 -0.562
TA2 -3.687 -4.501 -0.500 P TA2 -3.875 -5.126 -0.437 SA2 -4.125 -4.999 -0.468
TA2 -3.687 -4.750 -0.500 TA2 -3.875 -5.250 -0.500 SA2 -4.125 -4.999 -0.437 V
TB2 -3.687 -5.126 -0.437 TA2 -3.875 -5.251 -0.437 SA2 -4.125 -4.999 -0.437 S
TA2 -3.687 -5.250 -0.468 TA2 -3.875 -5.376 -0.500 SA2 -4.125 -5.126 -0.437 V
TA2 -3.687 -5.501 -0.500 TA2 -3.875 -5.501 -0.500 TA2 -4.125 -5.126 -0.500
TB2 -3.687 -5.626 -0.437 SA2 -3.875 -5.690 -0.500 SA2 -4.125 -5.251 -0.437 V
SA2 -3.688 -6.001 -0.500 TA2 -3.875 -5.751 -0.562 TA2 -4.125 -5.251 -0.468
UV -3.735 -4.648 -0.510 VF UTB2VM -3.932 -5.906 -0.512 SA2 -4.125 -5.501 -0.437 V
TC -3.740 -4.724 -0.512 UTB3VM -3.932 -5.906 -0.512 MOS2 TA2 -4.125 -5.501 -0.500
SB2 -3.740 -4.921 -0.472 TB3 -3.932 -5.906 -0.512 L TA2 -4.125 -5.751 -0.562
TC -3.740 -4.921 -0.512 SA2 -3.937 -4.876 -0.625 SA2 -4.125 -6.000 -0.625
TF -3.375 -3.948 -0.375 SA2 -3.937 -4.999 -0.437 V SA2 -4.125 -6.001 -0.437 V
VB2 -3.750 -4.376 -0.250 SA2 -3.937 -4.999 -0.437 TC -4.134 -5.315 -0.551
TA2 -3.750 -4.499 -0.468 P TA2 -3.937 -4.999 -0.468 TA2 -4.187 -4.999 -0.468
SB2 -3.750 -4.501 -0.375 V TA2 -3.937 -4.999 -0.468 L SA2 -4.187 -5.251 -0.468
TA2 -3.750 -4.626 -0.500 TC -3.937 -5.000 -0.468 TA2 -4.187 -5.501 -0.500
TB2 -3.750 -4.750 -0.500 TA2 -3.937 -5.126 -0.472 V TA2 -4.187 -5.751 -0.500
SA2 -3.750 -4.751 -0.437 SA2 -3.937 -5.251 -0.468 TA2 -4.187 -6.000 -0.500
SA2 -3.750 -4.751 -0.437 V TA2 -3.937 -5.376 -0.500 TA2 -4.187 -6.250 -0.500
SB2 -3.750 -4.751 -0.375 P TA2 -3.937 -5.501 -0.500 VB2Y -4.250 -5.126 -0.250
TA2 -3.750 -4.751 -0.500 TC -3.937 -4.724 -0.512 TB2 -4.250 -5.250 -0.500
TA2 -3.750 -4.751 -0.437 S TC -3.937 -4.921 -0.512 TA2 -4.250 -5.250 -0.500 L
TB2 -3.750 -4.751 -0.375 L TC -3.938 -4.404 -0.354 TC -4.250 -5.250 -0.500
TB2 -3.750 -4.751 -0.437 P TBR -3.990 -5.375 -0.500 SA2 -4.250 -5.251 -0.375
TA2 -3.750 -4.875 -0.500 SC -4.000 -4.750 -0.437 SA2 -4.250 -5.251 -0.437
SA2 -3.750 -4.999 -0.437 TA2 -4.000 -4.876 -0.625 SA2 -4.250 -5.251 -0.437 V
SB2 -3.750 -4.999 -0.375 V SA2 -4.000 -4.999 -0.437 V SB2 -4.250 -5.251 -0.375 S
TA2 -3.750 -4.999 -0.500 SA2 -4.000 -4.999 -0.437 TA2 -4.250 -5.251 -0.437
TA2 -3.750 -4.999 -0.437 SA2 -4.000 -4.999 -0.437 S TA2 -4.250 -5.376 -0.500
TB2 -3.750 -4.999 -0.375 SB2 -4.000 -4.999 -0.375 P SA2 -4.250 -5.500 -0.562
VB2Y -3.750 -4.999 -0.468 TA2 -4.000 -4.999 -0.500 TA2 -4.250 -5.500 -0.500
SA2 -3.750 -5.251 -0.437 V TA2 -4.000 -4.999 -0.500 L TA2 -4.250 -5.501 -0.438 L
TA2 -3.750 -5.251 -0.468 TA2 -4.000 -4.999 -0.437 TA2 -4.250 -5.626 -0.500
TA2 -3.750 -5.376 -0.500 TB -4.000 -4.999 -0.375 TB2 -4.250 -5.626 -0.437
TA2 -3.750 -5.501 -0.500 TB2 -4.000 -4.999 -0.375 V TA2 -4.250 -5.751 -0.562
TA2 -3.812 -4.876 -0.500 TB2 -4.000 -4.999 -0.375 SA2 -4.250 -5.876 -0.500 V
SA2 -3.812 -4.999 -0.468 TA2 -4.000 -5.125 -0.500 TA2 -4.250 -5.999 -0.500
SA2 -3.812 -5.251 -0.468 SB -4.500 -5.250 -0.375 TA2 -4.250 -6.126 -0.500
SB2 -3.875 -4.751 -0.375 TA2 -4.000 -5.250 -0.500 TA2 -4.250 -6.250 -0.562
TA2 -3.875 -4.751 -0.375 SA2 -4.000 -5.251 -0.437 V TA2 -4.250 -6.250 -0.500
TA2 -3.875 -4.751 -0.375 TB2 -4.000 -5.251 -0.437 SA2 -4.275 -5.500 -0.570
TB2 -3.875 -4.751 -0.375 TA2 -4.000 -5.310 -0.500 SA2 -4.312 -5.376 -0.500
TB2 -3.875 -4.751 -0.375 V SB2 -4.000 -5.375 -0.500 SA2 -4.312 -5.501 -0.562 P
TA2 -3.875 -4.875 -0.500 TA2 -4.000 -5.376 -0.500 TA2 -4.312 -5.501 -0.437 P
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
38
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
TA2 -4.312 -5.501 -0.437 TA2 -4.625 -5.751 -0.562 SB2 -5.000 -6.126 -0.500 V
TA2 -4.312 -5.751 -0.500 TA2 -4.625 -5.999 -0.500 SA2 -5.000 -6.250 -0.562
TA2 -4.312 -5.999 -0.500 TA2 -4.625 -6.250 -0.562 SA2 -5.000 -6.250 -0.500 p
TA2 -4.312 -6.250 -0.500 TA2 -4.687 -5.751 -0.500 SA2 -5.000 -6.250 -0.500 V
TA2 -4.330 -5.626 -0.472 V TA2 -4.687 -5.999 -0.500 SB2 -5.000 -6.250 -0.500
TC -4.331 -5.512 -0.551 SA2 -4.687 -6.250 -0.500 TA2 -5.000 -6.250 -0.500
TA2 -4.375 -5.376 -0.500 TA2 -4.687 -6.250 -0.500 TA2 -5.000 -6.250 -0.500 L
TA2 -4.375 -5.500 -0.500 TA2 -4.687 -6.374 -0.500 TB2 -5.000 -6.250 -0.500
TC -4.375 -5.500 -0.500 UTB2VM -4.719 -7.086 -0.591 L TA2 -5.000 -6.375 -0.500
TA2 -4.375 -5.626 -0.500 TB3 -4.719 -7.086 -0.591 L TA2 -5.000 -6.500 -0.500
TA2 -4.375 -5.751 -0.562 TB -4.724 -5.906 -0.551 TA2 -5.000 -6.749 -0.500
TA2 -4.375 -5.999 -0.500 TC -4.724 -7.874 -0.591 TA2 -5.000 -6.874 -0.500
TA2 -4.375 -6.125 -0.500 VB2 -4.750 -5.375 -0.312 TA2 -5.000 -6.877 -0.625
TA2 -4.375 -6.250 -0.562 SB2 -4.750 -5.749 -0.437 P TA2 -5.000 -7.000 -0.500
SA2 -4.437 -5.500 -0.562 SA2 -4.750 -5.750 -0.562 TA2 -5.000 -7.500 -0.500
SA2 -4.437 -5.501 -0.500 V TA2 -4.750 -5.750 -0.500 SA2 -5.062 -6.126 -0.500
TA2 -4.437 -5.751 -0.500 SB2 -4.750 -5.751 -0.500 SA2 -5.062 -6.374 -0.625
TA2 -4.437 -5.999 -0.500 SB2 -4.750 -5.751 -0.500 V SA2 -5.062 -6.375 -0.500 V
SB2 -4.500 -5.250 -0.375 TA2 -4.750 -5.751 -0.500 TB -5.118 -5.906 -0.394
TA2 -4.500 -5.251 -0.437 V TB2 -4.750 -5.751 -0.500 V TA2 -5.125 -6.125 -0.500
TA2 -4.500 -5.376 -0.437 TA2 -4.750 -5.876 -0.500 SB2 -5.125 -6.126 -0.500
TA2 -4.500 -5.376 -0.437 V TA2 -4.750 -6.000 -0.625 P TA2 -5.125 -6.126 -0.500
SA2 -4.500 -5.500 -0.562 SB2 -4.750 -6.001 -0.500 V TA2 -5.125 -6.250 -0.500
TA2 -4.500 -5.500 -0.500 TA2 -4.750 -6.001 -0.500 TB2 -5.125 -6.250 -0.500 V
SA2 -4.500 -5.501 -0.437 TA2 -4.750 -6.001 -0.500 L TA2 -5.125 -6.374 -0.500
SA2 -4.500 -5.501 -0.437 V TA2 -4.750 -6.125 -0.500 SA2 -5.125 -6.375 -0.500 V
TA2 -4.500 -5.501 -0.437 TA2 -4.750 -6.250 -0.562 TA2 -5.125 -6.499 -0.500
TB2 -4.500 -5.501 -0.375 TA2 -4.812 -5.999 -0.500 TA2 -5.187 -6.499 -0.500
VB2 -4.500 -5.501 -0.250 SA2 -4.812 -6.250 -0.500 SA2 -5.250 -6.250 -0.500 V
TA2 -4.500 -5.625 -0.500 SA2 -4.813 -5.751 -0.562 TA2 -5.250 -6.250 -0.500
SC -4.500 -5.750 -0.500 VB2 -4.875 -5.501 -0.250 TA2 -5.250 -6.375 -0.500
TA2 -4.500 -5.750 -0.500 TB2J4T -4.875 -5.558 -0.419 SS SA2 -5.250 -6.500 -0.500 V
TA2 -4.500 -5.751 -0.437 TA2 -4.875 -5.999 -0.500 TA2 -5.250 -6.500 -0.562
TB2 -4.500 -5.751 -0.375 V B -4.875 -6.000 -0.903 TA2 -5.250 -6.625 -0.562
TA2 -4.500 -5.876 -0.500 SA2 -4.875 -6.001 -0.500 V SA2 -5.250 -6.750 -0.500 V
TA2 -4.500 -5.999 -0.625 TA2 -4.875 -6.125 -0.500 TA2 -5.250 -6.750 -0.500
TA2 -4.500 -5.999 -0.500 SC -4.875 -6.250 -0.500 SA2 -5.275 -6.499 -0.562
TA2 -4.500 -5.999 -0.500 L TA2 -5.375 -6.624 -0.562 L TA2 -5.312 -6.500 -0.500
TC -4.500 -6.000 -0.500 TC -5.625 -6.500 -0.500 V TA2 -5.375 -6.374 -0.500
TA2 -4.500 -6.001 -0.500 TA2 -4.875 -6.250 -0.500 TA2 -5.375 -6.624 -0.562 L
TA2 -4.500 -6.001 -0.500 L TA2 -4.921 -6.375 -0.500 V SA2 -5.375 -6.625 -0.500 V
TA2 -4.500 -6.001 -0.500 V TA2 -4.937 -5.999 -0.500 TA2 -5.375 -6.749 -0.500
TA2 -4.500 -6.125 -0.562 TA2 -4.937 -5.999 -0.500 L SA2 -5.375 -6.750 -0.500 V
TA2 -4.500 -6.250 -0.500 TA2 -4.937 -6.250 -0.500 TA2 -5.375 -7.875 -0.750
TA2 -4.500 -6.374 -0.500 TA2 -4.937 -6.250 -0.500 L TB2 -5.500 -6.250 -0.500
TA2 -4.562 -5.751 -0.500 TA2 -4.937 -6.374 -0.500 SA2 -5.500 -6.500 -0.500 V
TA2 -4.562 -5.999 -0.500 TB2 -4.938 -6.001 -0.500 L SA2 -5.500 -6.500 -0.505 P
SA2 -4.562 -6.250 -0.500 SC -5.000 -6.000 -0.500 TA2 -5.500 -6.500 -0.562
UW -4.605 -6.005 -0.700 TA2 -5.000 -6.001 -0.500 TA2 -5.500 -6.625 -0.562
TA2 -4.625 -5.625 -0.500 TA2 -5.000 -6.001 -0.500 V SA2 -5.500 -6.750 -0.500 V
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
39
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Inches
SB2 -5.500 -6.750 -0.500 SA2 -6.250 -7.875 -0.625 TA2 -8.000 -9.000 -0.625
TA2 -5.500 -6.750 -0.575 TA2 -6.250 -7.875 -0.750 TA2 -8.000 -9.000 -0.750
TB2 -5.500 -6.750 -0.500 SA2 -6.375 -7.875 -0.625 TA2 -8.000 -9.250 -0.625
TA2 -5.500 -6.875 -0.562 TA2 -6.375 -7.875 -0.500 TA2 -8.000 -9.500 -0.625
SA2 -5.500 -7.500 -0.562 SA2 -6.500 -7.500 -0.500 V TA2 -8.000 -10.000 -0.625
TB2 -5.512 -6.299 -0.551 TA2 -6.500 -7.500 -0.562 TA2 -8.000 -10.125 -0.750
TC -5.512 -6.299 -0.551 TA2 -6.500 -7.500 -0.562 L SA2 -8.125 -10.125 -0.750
TC -5.512 -6.693 -0.591 V TB2 -6.500 -7.500 -0.500 TA2 -8.125 -10.125 -0.625
SA2 -5.625 -5.625 -0.500 V SB2 -6.500 -8.000 -0.500 SBR -8.250 -9.250 -0.625
TA2 -5.625 -6.624 -0.500 TA2 -6.500 -8.000 -0.625 SC -8.250 -10.250 -0.687
PBSCE -5.625 -6.500 -0.500 VSS TA2 -6.500 -8.000 -0.625 L TA2 -8.250 -10.250 -0.750
TB2J -6.250 -7.519 -0.959 TA2 -6.500 -8.000 -0.500 TA2 -8.250 -10.625 -0.750
KH -6.716 -7.750 -0.625 V TA2 -6.500 -8.000 -0.500 L TA2 -8.375 -10.375 -0.625
TC -6.716 -7.750 -0.625 V SA2 -6.625 -8.125 -0.500 SA2 -8.500 -9.750 -0.625 L
TA2 -5.625 -6.874 -0.500 TA2 -6.625 -8.125 -0.625 TA2 -8.500 -10.000 -0.625
SA2 -5.625 -6.875 -0.500 V TA2 -6.750 -8.000 -0.625 TA2 -8.500 -10.500 -0.625
TA2 -5.625 -6.875 -0.500 V TA2 -6.750 -8.250 -0.562 TB2 -8.500 -10.500 -0.625
SA2 -5.625 -7.125 -0.500 V TA2 -6.750 -8.500 -0.625 TB2 -8.500 -10.500 -0.625 L
TA2 -5.625 -7.125 -0.500 SA2 -6.875 -7.875 -0.625 TA2 -8.500 -10.625 -0.750
SB2 -5.630 -7.087 -0.551 V SA2 -6.875 -8.375 -0.625 SA2 -8.625 -10.625 -0.625 L
TA2 -5.750 -6.624 -0.625 TA2 -7.000 -8.000 -0.625 TA2 -8.625 -10.625 -0.750
SA2 -5.750 -6.625 -0.500 V SB2 -7.000 -8.250 -0.625 SA2 -8.750 -10.500 -0.750
SA2 -5.750 -6.750 -0.500 V TA2 -7.000 -8.250 -0.625 TA2 -8.750 -10.750 -0.750
TA2 -5.750 -6.750 -0.575 TA2 -7.000 -8.375 -0.625 TA2 -8.875 -10.122 -0.750
TA2 -5.750 -6.875 -0.562 SB2 -7.000 -8.500 -0.625 SA2 -8.875 -10.875 -0.750
SA2 -5.750 -7.000 -0.500 V TA2 -7.000 -8.500 -0.625 SA2 -9.000 -10.375 -0.625
TA2 -5.750 -7.000 -0.500 TA2 -7.000 -8.500 -0.625 L SA2 -9.000 -10.500 -0.750
TA2 -5.750 -7.001 -0.562 TA2 -7.000 -8.500 -0.625 V SA2 -9.000 -11.000 -0.625 L
TA2 -5.750 -7.125 -0.562 TB2 -7.000 -8.500 -0.500 TB2 -9.000 -11.000 -0.625 L
TA2 -5.750 -7.500 -0.562 TB2 -7.000 -8.507 -0.500 L TA2 -9.000 -11.000 -0.750
TA2 -5.750 -7.874 -0.750 P TA2 -7.000 -8.750 -0.625 SA2 -9.750 -11.125 -0.625 L
SA2 -5.875 -7.125 -0.500 V TA2 -7.000 -9.312 -0.625 SA2 -9.750 -11.750 -0.625 L
TA2 -5.875 -7.125 -0.500 TA2 -7.125 -8.625 -0.562 TB2 -10.000 -12.000 -0.625 L
TA2 -5.875 -7.125 -0.500 L TA2 -7.250 -8.250 -0.625 SB -10.375 -11.625 -0.875
SA2 -5.875 -7.500 -0.562 SA2 -7.250 -8.750 -0.750 P
SA2 -5.875 -7.500 -0.500 V TA2 -7.250 -8.750 -0.750
TC -5.906 -7.087 -0.551 SA2 -7.375 -8.875 -0.750
TB2 -6.000 -6.750 -0.500 V TA2 -7.500 -8.500 -0.625
TA2 -6.000 -7.000 -0.500 TA2 -7.500 -9.000 -0.750
TA2 -6.000 -7.125 -0.562 TA2 -7.500 -9.000 -0.625 P
TA2 -6.000 -7.500 -0.500 L TA2 -7.625 -8.625 -0.562
TA2 -6.000 -7.500 -0.562 TA2 -7.625 -9.125 -0.625
TA2 -6.000 -7.500 -0.562 L SA2 -7.750 -9.000 -0.625
SA2 -6.125 -7.125 -0.625 SA2 -7.750 -9.250 -0.625
TA2 -6.125 -7.500 -0.562 TA2 -7.750 -10.000 -0.750
SA2 -6.125 -7.627 -0.625 TB2 -7.875 -9.375 -0.625 L
SA2 -6.250 -7.252 -0.500 SA2 -7.875 -9.375 -0.750
SA2 -6.250 -7.500 -0.562 TA2 -7.875 -10.000 -0.625
SA2 -6.250 -7.500 -0.500 V GM -7.927 -9.182 -0.687
TA2 -6.250 -7.750 -0.500 SA2 -8.000 -9.000 -0.625
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
40
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Metric
41
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Metric
42
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Clark Seal Numbers in Metric
DCF -45 -85 -10 P TC -65 -85 -12 TC -110 -140 -14
TC -45 -85 -10 TC -65 -88 -8 SB2 -120 -150 -14
DTC4J -45.5 -58 -11.5 SS TC -65 -88 -12 TB -120 -150 -14 V
TC -46 -58 -7 SC -65 -90 -10 TC -120 -200 -15
TC -46 -70 -8 TC -65 -90 -12 TB -130 -150 -10
TC4J -47 -58 -10 SS TC -65 -90 -13 TB2 -140 -160 -14
VTYV -47 -70 -8.5 P DB -65 -90 -20 TC -140 -160 -14
TC -48 -62 -7 VBRTHP -65 -110 -15.3 SB2 -140 -170 -14
TB2 -48 -62 -8 TC -65 -140 -14 V80 TC -140 -170 -15 V
TC -48 -65 -9 TC -68 -90 -12 SB2 -160 -190 -13 V
TC -48 -65 -10 SC -70 -85 -8 XMHE -160 -194 -16 V
TC -48 -70 -12 TC -70 -90 -10 SB2 -180 -210 -16
TC -48 -72 -7 TC -70 -90 -12 TC -200 -290 -16 V
TC -49 -62 -6 TB -70 -92 -12
TC -50 -62 -7 TC -70 -92 -12
TC -50 -64 -8 TC -70 -95 -13
TC -50 -65 -8 SC -72 -90 -10
TC -50 -65 -9 SC -72 -95 -10
TB -50 -68 -7 SB2 -75 -95 -10 VLHS
TC -50 -68 -7 TC -75 -95 -12
UTCTH -50 -68 -10 SS UTCTH -75 -100 -10 SS
TC -50 -70 -9 TB -75 -100 -13
TC -50 -70 -10 TC -75 -100 -13
TC -50 -70 -12 TC -75 -105 -13
TC -50 -72 -9 UTCTH -75 -115 -10 SS
TC -50 -72 -10 TC -80 -100 -10
TC -50 -72 -12 TC -80 -100 -12
TC -50 -75 -12 TC -80 -100 -13
SB -50 -80 -10 SC -80 -105 -10
TC -50 -90 -10 TC -80 -105 -13
TC -50 -90 -12 SC -80 -120 -13
TB -55 -70 -18 TC -80 -120 -13
TC -55 -85 -14 TC -85 -100 -13
SB2 -55 -100 -8 UTCH -85 -110 -12 SS
TC -57 -85 -12 TC -85 -110 -13
TC -58 -80 -10 TC -85 -115 -13
TC -60 -75 -9 SC -85 -130 -12
TB -60 -77 -12 UTCH -85 -130 -13 SS
TC -60 -78 -9 SC -90 -110 -12
TC -60 -80 -10 TC -90 -115 -13
TC -60 -80 -12 TC -95 -120 -13
TC -60 -82 -12 SB2 -95 -125 -12
TC -60 -85 -12 TC -95 -125 -13
SC -60 -95 -10 TCL -100 -118 -9 V
SC -60 -110 -12 TCL -100 -118 -9
TC -60 -110 -12 UTCTH -100 -120 -12 S
TC -63 -80 -9 TC -100 -120 -13 SS
TC -63 -85 -12 TC -100 -125 -13
TC -65 -80 -12 UTCTH -100 -150 -13 SS
SC -65 -85 -10 TC -105 -135 -14
Suffix: Case Material, Garter Spring, Lip Material and Seal Coating – refer to page 4.
43
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Chicago Rawhide Interchange Tables
78738 TB2-7.875-9.375-.625L
79961 TA2-8.000-9.000-.625
79998 TA2-8.000-9.250-.625L
80038 TA2-8.000-10.000-.625
81246 TA2-8.125-10.125-.625
85014 TB2-8.500-10.500-.625
85015 TB2-8.500-10.500-.625L
86260 SA2-8.625-10.625-.625L
90036 TB2-9.000-11.000-.625L
92574 TA2-9.250-12.750-1.250
95048 SB2-9.500-10.500-.437SSSL
97542 SA2-9.750-11.125-.625
97550 SA2-9.750-11.750-.625L
100075 TB2-10.000-12.000-.625L
102520 SA2-10.250-11.250-.562
110030 TA2-11.000-12.500-.625
n o r D esign
550231 TC-35-55-11
Selecti o
I N E S
H ELPL (80 0 ) 5 65 1
-1240 • (918
) 664-0058
) 664-1146
7
7
NOTE: The seal part number consists of the Design Type, Shaft Diameter, Housing Bore Diameter and Seal Width dimensions, respectively. The letter
designation at the end of the part number indicates the type of elastomer which is used. If there is no letter at the end, the elastomer will be nitrile.
Lip materials: Blank–Nitrile, “E”–Neoprene, “P”–Polyacrylate, “S”–Silicone, “T”–TFE (Teflon), “V”–Viton
50
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
National Interchange Tables
60
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Temperature Conversion Table
In 1990, the General Conference changed the defining fixed point from the ice point to the triple point of water, 0.01oC, which is more easily reproduced than is
the ice point. The triple point is the condition under which three phases of matter can co-exist in equilibrium. By this action, the interval between the triple point
and steam became 99.99oC instead of 100oC and the international scale ceased to be a “centrigrade scale”. “Celsius” is used accordingly in this material.
Let °C and °F denote the readings on the Celsius and Fahrenheit Temperature Scales, respectively.
°C °F °C °F °C °F °C °F °C °F °C °F °C °F
-100 -148.0 -60 -76.0 -20 -4.0 20 68.0 60 140.0 100 212 500 932
-99 -146.2 -59 -74.2 -19 -2.2 21 69.8 61 141.8 110 230 510 950
-98 -144.4 -58 -72.4 -18 -0.4 22 71.6 62 143.6 120 248 520 968
-97 -142.6 -57 -70.6 -17 1.0 23 73.4 63 145.4 130 266 530 986
-96 -140.6 -56 -68.8 -16 3.2 24 75.2 64 147.2 140 284 540 1004
-95 -139.0 -55 -67.0 -15 5.0 25 77.0 65 148.9 150 302 550 1022
-94 -137.2 -54 -65.2 -14 6.8 26 78.8 66 150.8 160 320 560 1040
-93 -135.4 -53 -63.4 -13 8.6 27 80.6 67 152.6 170 338 570 1058
-92 -133.6 -52 -61.6 -12 10.4 28 82.4 68 154.4 180 356 580 1076
-91 -131.8 -51 -59.8 -11 12.2 29 84.2 69 156.2 190 374 590 1094
-90 -130.0 -50 -58.0 -10 14.0 30 86.0 70 158.0 200 392 600 1112
-89 -128.2 -49 -56.2 -9 15.8 31 87.8 71 159.8 210 410 610 1130
-88 -126.4 -48 -54.4 -8 17.6 32 89.6 72 161.6 220 428 620 1148
-87 -124.6 -47 -52.6 -7 19.4 33 91.4 73 163.4 230 446 630 1166
-86 -122.8 -46 -50.8 -6 21.2 34 93.2 74 165.2 240 464 640 1184
-85 -121.0 -45 -49.0 -5 23.0 35 95.0 75 167.0 250 482 650 1202
-84 -119.2 -44 -47.2 -4 24.8 36 96.8 76 168.8 260 500 660 1220
-83 -117.4 -43 -45.4 -3 26.6 37 98.6 77 170.6 270 518 670 1238
-82 -115.6 -42 -43.6 -2 28.4 38 100.4 78 172.4 280 536 680 1256
-81 -113.8 -41 -41.8 -1 30.2 39 102.2 79 174.2 290 554 690 1274
-80 -112.0 -40 -40.0 0 32.0 40 104.0 80 176.0 300 572 700 1292
-79 -110.2 -39 -38.2 1 33.8 41 105.8 81 177.8 310 590 710 1310
-78 -108.4 -38 -36.4 2 35.6 42 107.8 82 179.6 320 608 720 1328
-77 -106.6 -37 -34.6 3 37.4 43 109.4 83 181.4 330 626 730 1346
-76 -104.8 -36 -32.8 4 39.2 44 111.2 84 183.2 340 644 740 1364
-75 -103.0 -35 -31.0 5 41.0 45 113.0 85 185.0 350 662 750 1382
-74 -101.2 -34 -29.2 6 42.8 46 114.8 86 186.8 360 680 760 1400
-73 -99.4 -33 -27.4 7 44.6 47 116.6 87 188.6 370 690 770 1418
-72 -97.0 -32 -25.6 8 46.4 48 118.4 88 190.4 380 716 780 1436
-71 -95.8 -31 -23.8 9 48.2 49 120.2 89 192.2 390 734 790 1454
-70 -94.0 -30 -22.0 10 50.0 50 122.0 90 194.0 400 752 840 1544
-69 -92.2 -29 -20.2 11 51.8 51 123.8 91 195.8 410 770 850 1562
-68 -90.4 -28 -18.4 12 53.6 52 125.6 92 197.6 420 788 860 1580
-67 -88.6 -27 -16.6 13 55.4 53 127.4 93 199.4 430 806 870 1598
-66 -86.8 -26 -14.8 14 57.2 54 129.2 94 201.2 440 824 880 1616
-65 -85.0 -25 -13.0 15 59.0 55 131.0 95 203.0 450 842 890 1634
-64 -83.2 -24 -11.2 16 60.8 56 132.8 96 204.8 460 860 900 1652
-63 -81.4 -23 -9.4 17 62.6 57 134.6 97 206.6 470 878 910 1670
-62 -79.6 -22 -7.6 18 64.4 58 136..4 98 208.4 480 896 920 1688
-61 -77.8 -21 -5.8 19 66.2 59 138.2 99 210.2 490 914 930 1706
61
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Dimension Conversion Table
INCH to MM
Inch 0” 1” 2” 3” 4” 5” 6” 7” 8”
Fractions Decimals
25.4000 50.8000 76.2000 101.6000 127.0000 152.4000 177.8000 203.2000
.0156 .3969 25.7969 51.1969 76.5969 101.9969 127.3969 152.7969 178.1969 203.5969
1
1
⁄ 64 .0313 .7938 26.1938 51.5938 76.9938 102.3938 127.7938 153.1938 178.5938 203.9938
⁄ 32 3
.0469 1.1906 26.5906 51.9906 77.3906 102.7906 128.1906 153.5906 178.9906 204.3906
⁄ 64 .0625 1.5875 26.9875 52.3875 77.7875 103.1875 128.5875 153.9875 179.3875 204.7875
1
⁄ 16 5
.0781 1.9844 27.3844 52.7844 78.1844 103.5844 128.9844 154.3844 179.7844 205.1844
3
⁄ 64 .0938 2.3812 27.7812 53.1812 78.5812 103.9812 129.3812 154.7812 180.1812 205.5812
⁄ 32 7
.1094 2.7781 28.1781 53.5781 78.9781 104.3781 129.7781 155.1781 180.5781 205.9781
⁄ 64 .1250 3.1750 28.5750 53.9750 79.3750 104.7750 130.1750 155.5750 180.9750 206.3750
1
⁄8 .1406 3.5719 28.9719 54.3719 79.7719 105.1719 130.5719 155.9719 181.3719 206.7719
9
5
⁄ 64 .1563 3.9688 29.3688 54.7688 80.1688 105.5688 130.9688 156.3688 181.7688 207.1688
⁄ 32 11
.1719 4.3656 29.7656 55.1656 80.5656 105.9656 131.3656 156.7656 182.1656 207.5656
3
⁄ 64 .1875 4.7625 30.1625 55.5625 80.9625 106.3625 131.7625 157.1625 182.5625 207.9625
⁄ 16 13
.2031 5.1594 30.5594 55.9594 81.3594 106.7594 132.1594 157.5594 182.9594 208.3594
7
⁄ 64 .2188 5.5562 30.9562 56.3562 81.7562 107.1562 132.5562 157.9562 183.3562 208.7562
⁄ 32 15
.2344 5.9531 31.3531 56.7531 82.1531 107.5531 132.9531 158.3531 183.7531 209.1531
⁄ 64 .2500 6.3500 31.7500 57.1500 82.5500 107.9500 133.3500 158.7500 184.1500 209.5500
1
⁄4 .2656 6.7469 32.1469 57.5469 82.9469 108.3469 133.7469 159.1469 184.5469 209.9469
17
9
⁄ 64 .2813 7.1438 32.5438 57.9438 83.3438 108.7438 134.1438 159.5438 184.9438 210.3438
⁄ 32 19
.2969 7.5406 32.9406 58.3406 83.7406 109.1406 134.5406 159.9406 185.3406 210.7406
⁄ 64 .3125 7.9375 33.3375 58.7375 84.1375 109.5375 134.9375 160.3375 185.7375 211.1375
5
⁄ 16 .3281 8.3344 33.7344 59.1344 84.5344 109.9344 135.3344 160.7344 186.1344 211.5344
21
⁄ 64 .3438 8.7312 34.1312 59.5312 84.9312 110.3312 135.7312 161.1312 186.5312 211.9312
11
⁄ 32 .3594 9.1281 34.5281 59.9281 85.3281 110.7281 136.1281 161.5281 186.9281 212.3281
23
⁄ 64 .3750 9.5250 34.9250 60.3250 85.7250 111.1250 136.5250 161.9250 187.3250 212.7250
3
⁄8 .3906 9.9219 35.3219 60.7219 86.1219 111.5219 136.9219 162.3219 187.7219 213.1219
25
13
⁄ 64 .4063 10.3188 35.7188 61.1188 86.5188 111.9188 137.3188 162.7188 188.1188 213.5188
⁄ 32 .4219 10.7156 36.1156 61.5156 86.9156 112.3156 137.7156 163.1156 188.5156 213.9156
27
⁄ 64 .4375 11.1125 36.5125 61.9125 87.3125 112.7125 138.1125 163.5125 188.9125 214.3125
7
⁄ 16 29
.4531 11.5094 36.9094 62.3094 87.7094 113.1094 138.5094 163.9094 189.3094 214.7094
15
⁄ 64 .4688 11.9062 37.3062 62.7062 88.1062 113.5062 138.9062 164.3062 189.7062 215.1094
⁄ 32 31
.4844 12.3031 37.7031 63.1031 88.5031 113.9031 139.3031 164.7031 190.1031 215.5031
⁄ 64 .5000 12.7000 38.1000 63.5000 88.9000 114.3000 139.7000 165.1000 190.5000 215.9000
1
⁄2 .5156 13.0969 38.4969 63.8969 89.2969 114.6969 140.0969 165.4969 190.8969 216.2969
33
17
⁄ 64 .5313 13.4938 38.8938 64.2938 89.6938 115.0938 140.4938 165.8938 191.2938 216.6938
⁄ 32 35
.5469 13.8906 39.2906 64.6906 90.0906 115.4906 140.8906 166.2906 191.6906 217.0906
⁄ 64 .5625 14.2875 39.6875 65.0875 90.4875 115.8875 141.2875 166.6875 192.0875 217.4875
9
⁄ 16 .5781 14.6844 40.0844 65.4844 90.8844 116.2844 141.6844 167.0844 192.4844 217.8844
37
19
⁄ 64 .5938 15.0812 40.4812 65.8812 91.2812 116.6812 142.0812 167.4812 192.8812 218.2812
⁄ 32 39
.6094 15.4781 40.8781 66.2781 91.6781 117.0781 142.4781 167.8781 193.2781 218.6781
⁄ 64 .6250 15.8750 41.2750 66.6750 92.0750 117.4750 142.8750 168.2750 193.6750 219.0750
5
⁄8 .6406 16.2719 41.6719 67.0719 92.4719 117.8719 143.2719 168.6719 194.0719 219.4719
41
21
⁄ 64 .6563 16.6688 42.0688 67.4688 92.8688 118.2688 143.6688 169.0688 194.4688 219.8688
⁄ 32 43
.6719 17.0656 42.4656 67.8656 93.2656 118.6656 144.0656 169.4656 194.8656 220.2656
⁄ 64 .6875 17.4625 42.8625 68.2625 93.6625 119.0625 144.4625 169.8625 195.2625 220.6625
11
⁄ 16 45
.7031 17.8594 43.2594 68.6594 94.0594 119.4594 144.8594 170.2594 195.6594 221.0594
23
⁄ 64 .7188 18.2562 43.6562 69.0562 94.4562 119.8562 145.2562 170.6562 196.0562 221.4562
⁄ 32 47
.7344 18.6531 44.0531 69.4531 94.8531 120.2531 145.6531 171.0531 196.4531 221.8531
⁄ 64 .7500 19.0500 44.4500 69.8500 95.2500 120.6500 146.0500 171.4500 196.8500 222.2500
3
⁄4 .7656 19.4469 44.8469 70.2469 95.6469 121.0469 146.4469 171.8469 197.2469 222.6469
49
⁄ 64 .7813 19.8438 45.2438 70.6438 96.0438 121.4438 146.8438 172.2438 197.6438 223.0438
25
⁄ 32 .7969 20.2406 45.6406 71.0406 96.4406 121.8406 147.2406 172.6406 198.0406 223.4406
51
⁄ 64 .8125 20.6375 46.0375 71.4375 96.8375 122.2375 147.6375 173.0375 198.4375 223.8375
13
⁄ 16 .8281 21.0344 46.4344 71.8344 97.2344 122.6344 148.0344 173.4344 198.8344 224.2344
53
⁄ 64 .8438 21.4312 46.8312 72.2312 97.6312 123.0312 148.4312 173.8312 199.2312 244.6312
27
⁄ 32 .8594 21.8281 47.2281 72.6281 98.0281 123.4281 148.8281 174.2281 199.6281 225.0281
55
⁄ 64 .8750 22.2250 47.6250 73.0250 98.4250 123.8250 149.2250 174.6250 200.0250 225.4250
7
⁄8 .8906 22.6219 48.0219 73.4219 98.8219 124.2219 149.6219 175.0219 200.4219 225.8219
57
29
⁄ 64 .9063 23.0188 48.4188 73.8188 99.2188 124.6188 150.0188 175.4188 200.8188 226.2188
⁄ 32 59
.9219 23.4156 48.8156 74.2156 99.6156 125.0156 150.4156 175.8156 201.2156 226.6156
⁄ 64 .9375 23.8125 49.2125 74.6125 100.0125 125.4125 150.8125 176.2125 201.6125 227.0125
15
⁄ 16 .9531 24.2094 49.6094 75.0094 100.4094 125.8094 151.2094 176.6094 202.0094 227.4094
61 .9688 24.6062 50.0062 75.4062 100.8062 126.2062 151.6062 177.0062 202.4062 227.8062
⁄ 64
31
⁄ 32 .9844 25.0031 50.4031 75.8031 101.2031 126.6031 152.0031 177.4031 202.8031 228.2031
MM to INCH
mm
mm 0 10 20 30 40 50 60 70 80 90 100 110
inches
0 .3937 .7874 1.1811 1.5748 1.9685 2.3622 2.7559 3.1496 3.5433 3.9370 4.3307
1 .0394 .4331 .8268 1.2205 1.6142 2.0079 2.4016 2.7953 3.1890 3.5827 3.9764 4.3701
2 .0787 .4724 .8661 1.2598 1.6535 2.0472 2.4409 2.8346 3.2284 3.6221 4.0158 4.4095
3 .1181 .5118 .9055 1.2992 1.6929 2.0686 2.4803 2.8740 3.2677 3.6614 4.0551 4.4488
4 .1575 .5512 .9449 1.3386 1.7323 2.1260 2.5197 2.9134 3.3071 3.7071 4.0945 4.4882
5 .1969 .5901 .9843 1.3780 1.7717 2.1654 2.5591 2.9528 3.3465 3.7402 4.1339 4.5276
6 .2362 .6299 1.0236 1.4173 1.8110 2.2047 2.5984 2.9921 3.3858 3.7795 4.1732 4.5669
7 .2756 .6693 1.0630 1.4567 1.8504 2.2441 2.6378 3.0315 3.4252 3.8189 4.2126 4.6063
8 .3150 .7087 1.1024 1.4961 1.8898 2.2835 2.6772 3.0709 3.4646 3.8583 4.2520 4.6457
9 .3543 .7480 1.1417 1.5354 1.9291 2.3228 2.7165 3.1102 3.5039 3.8976 4.2913 4.6850
62
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Pressure Conversion Table
lbs/in 2 kg/cm 2 lbs/in 2 kg/cm 2 lbs/in 2 kg/cm 2 lbs/in 2 kg/cm 2 lbs/in 2 kg/cm 2 lbs/in 2 kg/cm 2
1 0.07 61 4.29 121 8.51 181 12.73 241 16.95 301 21.17
2 0.14 62 4.36 122 8.58 182 12.80 242 17.02 302 21.24
3 0.21 63 4.43 123 8.65 183 12.87 243 17.09 303 21.31
4 0.28 64 4.50 124 8.72 184 12.94 244 17.16 304 21.38
5 0.35 65 4.57 125 8.79 185 13.01 245 17.23 305 21.45
6 0.42 66 4.64 126 8.86 186 13.08 246 17.30 306 21.52
7 0.49 67 4.71 127 8.93 187 13.15 247 17.37 307 21.59
8 0.56 68 4.78 128 9.00 188 13.22 248 17.44 308 21.66
9 0.63 69 4.85 129 9.07 189 13.29 249 17.51 309 21.73
10 0.70 70 4.92 130 9.14 190 13.36 250 17.58 310 21.80
11 0.77 71 4.99 131 9.21 191 13.43 251 17.65 311 21.87
12 0.84 72 5.06 132 9.28 192 13.50 252 17.72 312 21.94
13 0.91 73 5.13 133 9.35 193 13.57 253 17.79 313 22.01
14 0.98 74 5.20 134 9.42 194 13.64 254 17.86 314 22.08
15 1.05 75 5.27 135 9.49 195 13.71 255 17.93 315 22.15
16 1.13 76 5.34 136 9.56 196 13.78 256 18.00 316 22.22
17 1.20 77 5.41 137 9.63 197 13.85 257 18.07 317 22.29
18 1.27 78 5.49 138 9.70 198 13.92 258 18.14 318 22.36
19 1.34 79 5.56 139 9.77 199 13.99 259 18.21 319 22.43
20 1.41 80 5.63 140 9.85 200 14.06 260 18.28 320 22.50
21 1.48 81 5.70 141 9.92 201 14.14 261 18.35 321 22.57
22 1.55 82 5.77 142 9.99 202 14.21 262 18.42 322 22.64
23 1.62 83 5.84 143 10.06 203 14.28 263 18.50 323 22.71
24 1.69 84 5.91 144 10.13 204 14.35 264 18.57 324 22.78
25 1.76 85 5.98 145 10.20 205 14.42 265 18.64 325 22.86
26 1.83 86 6.05 146 10.27 206 14.49 266 18.71 326 22.93
27 1.90 87 6.12 147 10.34 207 14.56 267 18.78 327 23.00
28 1.97 88 6.19 148 10.41 208 14.63 268 18.85 328 23.07
29 2.04 89 6.26 149 10.48 209 14.70 269 18.92 329 23.14
30 2.11 90 6.33 150 10.55 210 14.77 270 18.99 330 23.21
31 2.18 91 6.40 151 10.62 211 14.84 271 19.06 331 23.28
32 2.25 92 6.47 152 10.69 212 14.91 272 19.13 332 23.35
33 2.32 93 6.54 153 10.76 213 14.98 273 19.20 333 23.42
34 2.39 94 6.61 154 10.83 214 15.05 274 19.27 334 23.49
35 2.46 95 6.68 155 10.90 215 15.12 275 19.34 335 23.56
36 2.53 96 6.75 156 10.97 216 15.19 276 19.41 336 23.63
37 2.60 97 6.82 157 11.04 217 15.26 277 19.48 337 23.70
38 2.67 98 6.89 158 11.11 218 15.33 278 19.55 338 23.77
39 2.74 99 6.96 159 11.18 219 15.40 279 19.62 339 23.84
40 2.81 100 7.03 160 11.25 220 15.47 280 19.69 340 23.91
41 2.88 101 7.10 161 11.32 221 15.54 281 19.76 341 23.98
42 2.95 102 7.17 162 11.39 222 15.61 282 19.83 342 24.05
43 3.02 103 7.24 163 11.46 223 15.68 283 19.90 343 24.12
44 3.09 104 7.31 164 11.53 224 15.75 284 19.97 344 24.19
45 3.16 105 7.38 165 11.60 225 15.82 285 20.04 345 24.26
46 3.23 106 7.45 166 11.67 226 15.89 286 20.11 346 24.33
47 3.31 107 7.52 167 11.74 227 15.96 287 20.18 347 24.40
48 3.38 108 7.59 168 11.81 228 16.03 288 20.25 348 24.47
49 3.45 109 7.67 169 11.88 229 16.10 289 20.32 349 24.54
50 3.52 110 7.74 170 11.95 230 16.17 290 20.39 350 24.61
51 3.59 111 7.81 171 12.03 231 16.24 291 20.46 351 24.68
52 3.66 112 7.88 172 12.10 232 16.32 292 20.53 352 24.75
53 3.73 113 7.95 173 12.17 233 16.39 293 20.60 353 24.82
54 3.80 114 8.02 174 12.24 234 16.46 294 20.68 354 24.89
55 3.87 115 8.09 175 12.31 235 16.53 295 20.75 355 24.96
56 3.94 116 8.16 176 12.38 236 16.60 296 20.82 356 25.04
57 4.01 117 8.23 177 12.45 237 16.67 297 20.89 357 25.11
58 4.08 118 8.30 178 12.52 238 16.74 298 20.96 358 25.18
59 4.15 119 8.37 179 12.59 239 16.81 299 21.03 359 25.25
60 4.22 120 8.44 180 12.66 240 16.88 300 21.10 360 25.32
63
customerservice@clarkseals.com / www.clarkseals.com / 1-8800-5565-11240
Shaft Seal Selection Consideration
Considerations:
Shaft diameter Does the equipment vibrate
Bore diameter Dynamic Shaft Runout (TIR) (inches)
Seal Width Shaft to bore misalignment (inches)
Fluid type Shaft surface roughness (RA)
Level of fluid relative to shaft Shaft hardness (Rockwell)
Max. operating temperature (°°F) Shaft material
Max. cavity pressure (PSI) Bore finish (RA)
Rotating shaft speed (max) (RPM) Housing material
Reciprocating shaft speed (FPM) Housing depth
Is there thermal expansion of the housing Grease flushing feature required
Seal under lip temperature (°°F) Light dust exclusion
*Direction of Rotation Heavy dust exclusion
Corrosive environment Seal life expectation
Seal Specifications:
Clark Seal Part No. Case material
Lip material Spring material
Durometer Latex coated
Date:
By:
* When viewed facing the air side of the seal when assembled on the shaft
Manufacturing Plant
in Tulsa, Oklahoma
WARRANTY
Clark Seals, Ltd. warrants its manufactured products to be free from defects in materials and workmanship for up to one full
year from the date of purchase. The manufacturer’s obligation under this warranty is limited to replacing any returned seal
which, upon inspection by the manufacturer, proves to be defective. We will not replace any seal that is defective due
to abuse, alteration by others, accident, misapplication, improper installation or normal wear and tear. The customer shall
be responsible for all return shipping costs. Under no circumstance shall Clark Seals, Ltd. be liable for any amount in excess
of the actual purchase price paid for the seals, nor for cost of installation of replacement parts. This warranty is in
lieu of all other warranties, expressed or implied, including warranty of merchantability. The manufacturer assumes no
responsibility whatsoever for consequential damages resulting from the use of its products.