XL.NO HEAT - ExcelUK
AM DISCONNECT ELECTRICAL SUPPLY TO DRYER PRIOR TO SERVICING W
CLEANING INSTRUCTIONS
OUTSIDE
Gently wash cover (including ar niet holes) using a sof cloth or sponge and a mils soap 0: detergent wit lukewarm water to loosen dit and grime.
INSIDE - CLEANING SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL
Wath normal use. cryer wil require cleaning once a year. Heavier usage requires more frequent cleaning. Linon the arnt or other intemal
pars of dryer will reduce efcieny and shorten the Ife ofthe working parts. To clean, remove cover by unscrewing the tamper-proof bol from cover
wi he special wrench provided wih each dryer. Use a small sof brush to gant cean al parts
TROUBLESHOOTING YOUR DRYER
As with any electrical appliance, repairs to be performed by qualified service personnel
your dryer does not tum on
1. Very thatthe dryer is receiving power by checking elnctrical
Service, orci breaker or use tothe dyer
2, Check voltage to dryer terminal block
3. Check RED service LED light forthe folowing
Light is ON - Pisce hands under sensor. fight stay on, then
Teplace sensor. Fight goes off, chock io make sure wiring ls
correct at dryer contrel. OK, check motor fuse 30 equipped,
‘and wire connecting to maior. If bth are OK, replace motor
Jght s OFF — Check for oose, disconnected or improper wing
At cryer contrat (See wiring schematics insie dryer cover), or
replace dryer contro,
Light is ELASHING ~ Dryer i in ockout moe. (Soe instalation
rote)
Ut your dryer does not shut off
1. May be mounted too lose to @ counter or object
(Gee installation note).
2. Check fo loose, discannected or improper wing al dryer contro
(See wring schematic inside dryer cover)
3. Replace dyer contol
XLS - 500Watt uni
I your dryer does not always turn an, or turns on by itself
1 May be mounted to0 close to a counter or object
(See instalation note)
2, Check fr foreign matrial on optical sensor nex oar outlet,
3. Check for loose wires on dryer contra
4 Replace dryer contra.
It your dryer has @ loss of air volume
1. Check for arleaks atthe heating
replace heating element or nozte.
2, Check fr slow running moter or burning smell. 30, replace
vent ornozze. leaking,
Note: Ifthe problom cannot be resolved withthe above, please cat
the telephone shown below and one of our tained technilans Wil be
happy to assist you.
No heating element - this is a cold air dryer
03 solutions Itd
centre house
79 chichester st
belfast
bt 4je
0800 458 7416
+44 28 9065 6552
www.o3solutions.comXL NO HEAT - ExcelUK
INSTALLATION INSTRUCTIONS FOR XLERATOR» HAND DRYER
FOR PROPER ELECTRICAL CONNECTIONS, CHECK YOUR LOCAL BUILDING CODES.
YOUR UNIT MUST BE INSTALLED BY A QUALIFIED, LICENSED ELECTRICIAN.
‘Suggested Mia. Heights from floor
tobottom of drver , r
Men's 45° (1143 mm) as
Ladies 3" (1092 mm)
Teenagers 44" (1041 mm) eye
‘Sm. Children 35" (889 mm) oe
Handicapped 37"(940 mm)
IF MOUNTING OVER COUNTERTOP. DISTANCE FROM
WALL
COUNTER TO DRYER MUST BE 15° (381mm) MINIMUM OF ane fe | a
= N Sb
Masonry Wall "expansion sieeve wth lag bolt . ba ce
Halon Wal ewig ype tough bot tet
Wooden Wat "lag Seow wih washer | pe FO
1 Ramove cover of dryer by unscrewing he tamper-proo! bolts from the sides ofthe caver with the special wrench provided with each uni.
2. Attach wal pate atthe four comers to smooth wal.
In locations where vandalism isa concern, use the two addtional mounting holes shown,
Remove control assembly to access right side mounting hole, Attach with the recommended type of fastener (see abov0)
8. Connect a 220/240V dryer to np mare than a 18 Amp. dedicated branch circuit using a least a #14 GA copper wee.
Attch lines to terminals as
Indicated by the schematc inside dryer. Be sure that an equipment ground wire i securely fastened fo green ground screw on base plate, Dyers
‘shouldbe installed per local code requremans,
4. In mutipi installations. before replacing cover. check the Serial Number marked inside the dryer tobe sure it matches the Serial Number marked
I al the boltom of cover, PLEASE DO NOT SWITCH COVERS. Do not forget to leave the speci
‘TAMPER PROOF WRENCH with
INSTALLATION NOTE: Ifthe dryer will not tum on, stays on or stops working, It may be mounted fo0 close fo a counter or abject. Turn off he
power to dryer fer 10 seconds and then reapply power. If dryer wil start, then turn off again, relocate the abject or remount dryer. this is not
ossibo, adjust he range of tho sensor by turing te range adlustment onthe coro board, counterclockwise lo decrease sensor range,
NOTE: Upon completing insalalon and checking for proper operalion, is Righly recommended thal a baad of ellicone sealant be placed around
the outside ofthe cover atthe wal to protect dryer fom inom coeosion caused by wash water an cleaning slutons
24 PARTS LIST FOR XLERATOR DRYER
REENO. DESCRIPTION
ns A. Gover es Namopate
2 Novena
33 Tampersrot sot
XL4 Tamper pro! rene
RES Aout ond one)
A6 Fomine tele ews)
RL? ContolAssony 8 Sensor
M9 Moor Assay
X10 Wal i samy
; XEN Covert breckts
312 Housing Geomert
X13 Housing Retainer
ff ALM Reco tt(ADA)
fs BL 1S Opes Asam (Sense
S ACNE Paerlsr tao equppes)
eaten)
1080.4
NOTE: Mode! Serial Number and Voltage of
Funes equipped)
dryer MUST BE included when ordering pats