VICKERS INCORPORATED
HYDRAULIC FLUID RECOMMENDATIONS:
AGRICULTURAL, CONSTRUCTION,
EARTHMOVING, MATERIAL HANDLING AND OTHER MOBILE MACHINI
uL-TYRE
Gils used in hydraulic systems perform the dual
function of iubriettion and transmission of power. Oil
Tost be selecied with care and wilh the assistance of 8
eputable supplier.
fine Tost Sequence” for evaluating ols for API (Ameri.
Ean Petroleum naitue) service MS (Maximum Severity)
feet serve the needa of mobo hydraulic aystoms, These
fnpine sequence tests were adopted by the Society of
‘Kstomotive Engineers, "American Society for Testing
Materials, and automotive engine builders. The MS
Classification i the Hey to selection of lls containing
{be typeof compounding that vill extond the operating
life ofthe hydric system. Oils meeting Diesel engine
requirements, DG. through DS classifications, may or
fay aot have the type of compounding desired for high
performance ysrauli systems
‘The following table summarizes the oll tres (vis
coolly and service classification) that are recommended
{or use with Vickers equipment. This selection is ost
Important and should be made with considerable care.
SAE
vscostty
vow
20-200
230
Ftow-30
‘APL Service
Glaseitenticn
ws-
Me
Ms
‘Astomatic ‘Tranemission Fld, Type A" is usually
satisfactory for power steering sysloms or those syS~
tome eperating under moderato hydraulic service,
‘OPERATING TEMPERATURES
"These temperabare rangos for each grade of ol are
satisfactory if sultable procedures are followed for low
emperature atart-up conditions and if sustained oper
‘Mien ip avoided at the upper temporature limits, Oper-
tion in excess of these temperatures results In in-
creased wear of the system components and causes mare
Fapid delerloration of te oll. For optimam operation,
f'taximum ofl viscosity of 4000 $8U atthe low temper
fure start-up condition and’ miniam cll viscosity of 60
SU for Ue sustalaed high temperature operating con
dition are recommended,
(Good olla are the most economical. Specifications can
tbe ‘set up which will indicate, to 2 limited degree, the
Characteristics eovential in a good hydraulic oll. These
fie listed herein and should be checked withthe oil man~
Sfaoturer prior tothe use of is predict.
viscosrr
“Dicom ss the measure of Duldity, The ofl must
have slficlent body to provide adequate sealing effect
between working parts of pumpe, valving, cyindera, ete,
SUPERSEDES M-417-5
‘but not enough to eause pump Intake caval
fish valve action, Viacoeity recommendations must
feet be 4 compromire, which takes ino consideration the
Working lomperature range, the type of hydraulic equip~
Inert used, andthe clang of service, Refer to table of of
‘iscosity tecommendations.
‘YiscosiTy INDEX,
"Tie viscoety tex ia a meagure of the rate at which
temperature changes cause 4 change i ll viscosity. 1
te very desicable a the ofl viscosity romain as early
Constant as possible under the wide range of temperahire
ontltions encountered in operating mooie and constric
{ion machinery. The viacosity index (V.L) of bydeaulie
Gl should not be lee than 0 for ths type of wervice
ADDITIVES
Research has developed & number of additive agente
which materially improve various characteriatice of olle
Ter hydric systema, “They may be selected for com-
ponding with a view toward reducing wear, increasing
Chemical stability, inhibiting corrosion, depressing post
Dolnt and improving the antisfoam characteristics. Pro~
Per use of additive agents requires specialized knowl-
‘Sdge, and they should be Incorporated by the ofl mans
fackurercnly, ao serious trouble may otwrwise result
Most oll companies have several brands of crankease
vile of eomewnat varying formulation that will meet the
IPT service classification of MS. The more desirable of
‘hese cls for hydraulic eervice will contain hgher 2-
‘mounts of the type of compounding that avoids scuffing
{hd wear cf eam lobes and valve Liters. ‘These ofls will
{iso be formulated tobe stable under oxidative conditions
nd when in contact with small amounts of moisture,
‘There should slso be reasonable protection against rust
to any ferrous materials sxbmerged in the oll or covered
by the oil's fz
(CLEANLINESS
“Thorough preceutions should be taken to filter the oil
fn the entire hydraulle aystom prior to it inital use to
‘remove paint metal chip, welding sho, Unt, etc. 1 (his
Is not dene, damage to te hydraulic oyster wil proba
biy result. In addition, continuing filtration 'e required
to remove sludge and products of wear and corresion,
‘rcughout the Le ofthe system.
Procautions shouldbe taken in the design of hydraulic
circuits t9 angure Dat a means Is provided to keep te
fil clean, This cai best be accomplised by thease of @
25 inieron full-flow filter or a 10 micron by-pass filter
plus a micronie filer type air breather or sealed res-
voir,
Dumps and motors, Tis always good practice,
Touse the best quality oll avalable forall componsats.
RELEASED $-1-02R W.S.
caTALos
HYDRAULIC O1L
RECOMMENDATIONS
AGRICULTURAL, CONSTRUCTION, EARTHMOVING,
MATERIAL HANDLING & OTHER MOBILE MACHINERY
DATA SHEET |
M-2950-5, PAGE 9800Foster Power Tong Model 58-938
LUBRICATION
Grease Fittings Transt
‘Any soft gun lubricant Oil meeting API class MS
Temp. above 32°F. SAE 20W
iy Temp. below 32° F. SAE 10W
(Capacity - 10 Quarts)"
OPERATIONAL MAINTENANCE
Note 1.
Note 2.
Note 3.
Note 4.
SAFETY POINTS AND WARNINGS.
Note 5.
Note 6.
Note 7.
Note 8.
Lube Fitting in
Drag Ring, Remove
Guide Boll,
Oil Level ~
Lube fittings should be greased weekly.
Transmission should be checked after every trip, and_if_water_or dirt is found in transmission,
change oil. Under normal conditions oil should be changed|very_ 100 work hours]
Clean and grease Tong Head and Backup Tool after every trip, use Kerosene or solvent and a
wire brush for cleaning. After cleaning, apply cup grease to jaws, pins, ring gear and top seal
Hazards of steam cleaning Tong Head are: Water will be forced by top seal into transmission,
‘also removing all lubricants from top seal and causing it to harden. If steam cleaning is used, Guide
Bell should be bolted in place and after cleaning, the transmission should be checked for the
presence of water.
CAUTION, keep hands clear of Tong Head while Tongs are in operation. Caution should be taken
‘while operating this equipment, as parts inside the Tong Head rotate.
Do nwt craw! or stand under Tongs as hydraulic line could be cut or broken and Tongs will fall.
Do not operate Power Tongs until the Anchor Arm is attached to the Tong and Anchor Post.
Power should be off before any size equipment change, maintenance, or any other work is done
to this equipment.Maintenance Checklist
Foster Power Tong Type 58-93R.
Grease Fittings
ine Chocked
1. Backup Tool Jaws
2. Backup Tool Swival
3, Tong Drag Ring
4, Transmission Case
Oil checked and/or changed,
5. Cleaning and
Greasing Tong HeadGUIDE BELL*
COVER PLATE
XN ys oe
INSERTS ae] i
JAWS @ me-<———— DRAG PLUGK
3 KDRAG RING———_ \ X= serine *
moos SET SCREWK
‘s : Bes”
eng 93-7
wai aaa 93-13
: Ir920
oa =P AS
93-2 5 = 123-27
T3240 56 Qa R
se
fees Wzaoae>
93-25
VS: a : .
93-30. = it | mi
ee = a
Ura]
285 — press IFI96
33.2881 11-632 «
~ {1-1160- PAGES |2-I5FOR
eo a i MR IZ AND PART NO.
THLINL 44 3SEE PAGE I6 FOR
SIZE AND PART NO.
#T aT
FINAL DRIVE ASSEMBLY é
POWER TONG TYPE 58-93-R e z 23
Se« ce
: S\2 G/F B|zs
fo a|z @|eo 2/06
= 3 5\2 5|8 3\£2
az Part NAME 2|6 2|3 €| >=)
——
7% | Washer 3/8" Lock Ger pO ere ae
11-255 _ | Washer 3/4" Flat 1| PF. 206 3
11-603 + | Cap Screw 3/8" x2 174" Hex.Hd. 78 | 204
=920__[ Safety Pin 3_1/2" 1 -01
T1=1160%| Cap Screw 3/8" x 2 1/4" Hex. Hd. 12 08
38-47-TA| Oil Seal, 9594 L.P.D. Fea Pr
33-2 Top Bearing Cap 1 [B-1741| 43.50
93-3-3 TED
93-4-2 ¢ | Final Dri 1 [patszdvon.00_| a7
93-7 Roller Bearing _ /72¥OS7_ 2 |A-2693| 9.00 B
93-13 | Base Rina A-3209| 3.50 | 1.
B-1740 32,50GH-Foster
POWER TONGS TYPE 58-93-R JAW LIST
Items Shown With * Are Included In Other Jaw Sets And Should Not Be Duplicated
1-5/16" OD Thru 1.9" OD Tubing Jaw Set Includes:
5 50-149-6 Jaws
10 5048-5 Inserts
10 50-49-2 Insert Screws
#1 50-15-2 Drag Ring (1" Straight Pin, 5" Bore)
1 93-5-10 Guide Bell (3-1/2" Bore)
*1 93-161 Cover Plate (5" Bore) ¥”
7 OD Thru 2-3/8" OD Tubing Jaw Set Include:
5 58-330 Jaws
10 58-328 Inserts
20 50-49-2 Insert Screws
*1 50-15-2 Drag Ring (1" Straight Pin, 5" Bore)
*1 93-5-7 Guide Bell (5" Bore)
1 93-161 Cover Plate (5" Bore)
2.3/8" OD Thru 27/8" OD Tubing Jaw Set Includes:
‘i 5 50-22-7 Jaws
10 5048-1 Inserts
20 50-49-2 Insert Screws
1 50-15-2 Drag Ring (1" Straight Pins, 5" Bore)
1 98-5-7 Guide Bell (5" Bore)
1 98-161 Cover Plate (5" Bore)
2-7/8" OD Thru 3-1/2" OD Tubing Jow Set Includes:
5 50-22-8 Jaws
10 50-48-11 Inserts
20 50-49-2 Insert Screws |
*1 50-15-2 Drag Ring (1" Straight Pins, 5" Bore)
*1 93-557 Guide Bell (5" Bore) |
*1 98-161 Cover Plate (5" Bore) 4
3-1/2" OD Thru 4-1/2" OD Tubing Jaw Set Include
5 50~22-11 Jaws (Solid)
1 58-160-2 Drag Ring (1" Str. Pins, 6-1/4" Bore)
1 98-5-11 Guide Bell (6-1/4" Bore)
1 93-161-3 Cover Plate (6-1/4"
| -@=-
4" OD Thru 5" OD Tubing Jaw Set Includes:
5 50-22-12 Jaws (Solid)
+1 58-160-2 Drag Ring (1" Str. Pins, 6-1/4" Bore)
*1 —-93-5-11 Guide Bell (6-1/4" Bore)
*1 -93-161-3 Cover Plate (6-1/4" Bore)5" OD Thru 6-1/16" OD Tubing Jaw Set Include:
5 58-314 Jaws (Solid)
1 58-160-2 Drag Ring (1" Str. Pins, 6-1/4" Bore)
1 93-5-11 Guide Bell (6-1/4" Bore)
1 93-161-3 Cover Plate (6-1/4" Bore)
POWER TONGS TYPE 58-93-R CASING JAW LIST
4" OD Thru 4-1/2" OD Casing Jaw Set Includes:
5 58-154-2 Jaws (Solid)
1 58-160-1 Drag Ring (3/4" Str. Pins, 7-1/4" Bore)
21 93-5-12 Guide Bell 7-1/4" Bore)
J..1 98-161-1 Cover Plate (7-1/4" Bore)
00 Thru 5-1/2" OD Casing Jow Set Includes:
* 5 58-158-2 Jaws (Solid)
58-160-1 Drag Ring (3/4" Str. Pins, 7-1/4" Bore)
Bore)
93-161-1 Cover Plate (7-1/4" Bore)
1
1 93-5-12 Guide Bell (7-1/4
1
65/8"
OD Casing Jaw Set Include:
10 58-336 Jaws (Solid)
1 58-332-2 Drag Ring (5/8" Str. Pins, 7-7/8" Bore)
1 93+5-14 Guide Bell (7-7/8" Bore)
1 98-161-8 Cover Plate (7-7/8" Bore)
" OD Casing Jaw Set Includes:
10 58-331 Jaws (Solid)
1 58-332-2 Drag Ring (5/8" Str. Pins, 7-7/8" Bore)
1 93-5-14 Guide Bell 7-7/8" Bore)
93-161-8 Cover Plate (7-7/8" Bore)
14GH-Foster
POWER TONGS TYPE 58-93-R
DOUBLE ACTION JAW LIST
Items Shown With * Are Included In Other Jaw Sets And Should Not Be Duplicated
1" OD Thru 15/16" OD Tubing Jaw Set Includes:
3 58-305 Jaws
3 58-306 Inserts
3 11-683. Insert Screws
1 50-15-5 Drag Ring (1" Str. Pins, 3-1/2" Bore)
1 93-5-10 Guide Bell (3-1/2" Bore)
1 93-161-9 Cover Plate (3-1/2" Bore)
2" OD Tubing Jaw Set Includes:
5 58-307 Jaws
5 58-308 Inserts
5 11-683 Insert Screws |
*1 50-15-2. Drag Ring (1" Str. Pins, 5" Bore)
*1 -93-5-7 Guide Bell (5" Bore)
*1 93-161 Cover Plate (5" Bore)
2-3/8" OD Thru 3-1/16" OD Tubing Jow Set Includes:
5 58-303 Jaws |
5 58-304 Inserts |
5 11-683 Insert Screws |
1 50-15-2 Drag Ring (1" Sir. Pins, 5" Bore)
1 93-5-7 Guide Bell (5" Bore)
1 98-161 Cover Plate (5" Bore)
3-17" op Tubing Jaw Set Includes:
58-303 Jaws
. 58-304-1 Inserts
5 11-683 Insert Screws
1 50-15-2 Drag Ring (1"" Str. Pins, 5" Bore)
*1 -7 Guide Bell (5" Bore) |
"1 93-161 Cover Plate (5" Bore)
3-11/16" OD Tubing Jaw Set Includes:
5 58-308 Jows
5 58-304-2 Incerts
5 ‘11-683 Insert Screws
015 2 Drag Ring (1"* Str. Pins, 5" Bore)
155GH-FOSTER BACKUP TYPE 147 JAWS
Power Tong Type 58-93R
1-5/16" OD Thru 2-1/16" OD Jaw Set Includes:
5 50-149-5 Jaws
i 50-48-5 Inserts
5 50-49-2 Insert Screws
2-3/8" OD Thru 3-3/4" OD Jaw Set Includes:
5 147-7. Jaws
5 50-48-1 Inserts
10 50-49-2 Insert Screws
" OD Thru 4-1/2" OD Jaw Set Includes:
147-14 Jows
50-48-1 Inserts
50-49-2 Insert Screws
4-1/2" OD Thru 5-9/16" OD Jaw Set Includes:
5 147-10 Jaws (Solid)
5" OD Thru 6-1/16" OD Jow Set Includ:
5 147-8. Jaws (Sol:
‘The Backup must have a 6-1/4" hole through the head to use the 4-1/2" OD to 5-9/16" OD
cond the 5" OD to 6-1/16" OD Jaw equipment. The 147-19 housing adaptor is used on the
other size equipment to reduce the hole from 6-1/4" OD to 5" OD.
The Sizes listed are actual OD of tubing, upset or collar the jaws will catch.
‘One set of jaws are included in the price of the backup.
16
oi m aban