Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Válvula solenoide (transmisión) - Instalar Herramienta Número de pieza Parte Descripción Cant.
UNA 180-3034 Soporte de reparación 4
Transmisión (Power Shift) - Quitar
8S-7615 Alfiler 2
Transmisión (Power Shift) - Desmontar
4C-6486 Estar 2
Transmisión (Power Shift) - Ensamblar si
8S-7641 Tubo 2
Transmisión (Power Shift) - Instalar
8S-8048 Sillín 2
Transmisión (transmisión directa): desmontar
C 208-5040 Tubo de soporte 1
Transmisión (transmisión directa): ensamblar
re 1U-7505 Gato hidraulico 1
Freno de estacionamiento: quitar e instalar
tabla 1
Eje de transmisión (trasero): quitar e instalar
Nota: Coloque marcas de identificación en todas las líneas, en todas las mangueras, en
todos los cables y en todos los tubos para fines de instalación. Tape todas las líneas,
mangueras y tubos. Esto ayuda a prevenir la pérdida de líquido y ayuda a evitar que los
contaminantes ingresen al sistema.
1. Connect the lock for the boom. Refer to Operation and Maintenance Manual,
"Boom Lock".
2. Connect the lock for the swing boom. Operation and Maintenance Manual, "Swing
Lock Pin Control".
3. Connect the lock for the extendable stick. Refer to Operation and Maintenance
Manual, "Extendable Stick Lock Control".
4. Lower the bucket to the ground. Place the control for the bucket into the FLOAT
position.
5. Drain the transmission oil into a suitable container for storage or disposal. Refer to
Operation and Maintenance Manual, "Transmission Oil - Change".
6. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump -
Remove".
7. Remove the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft
(Front) - Remove and Install".
https://sis2.cat.com/#/service-detail?
serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false
https://sis2.cat.com/#/service-detail?serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false 1/6
22/9/2020 SIS 2.0
Illustration 1 g01244146
Illustration 2 g01244145
8. Raise the machine so that the machine is level and 914 mm (36 inch) off of the
floor. Install Tooling (A) and Tooling (B) under the machine.
Illustration 3 g01244175
9. Install Tooling (A) and Tooling (C) in order to support the engine when the
transmission is removed.
Illustration 4 g01243334
10. Disconnect harness assemblies (1), (2), (3), (4), (5), (6), and (7).
https://sis2.cat.com/#/service-detail?
serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false
https://sis2.cat.com/#/service-detail?serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false 2/6
22/9/2020 SIS 2.0
Illustration 5 g01243338
Illustration 6 g01243656
12. Disconnect harness assembly (13). Remove nuts (12) and (14). Remove solenoids
(11) and (15) and remove the plungers.
Illustration 7 g01243838
13. Disconnect hose assembly (16) from the right side of the transmission.
Illustration 8 g01243661
https://sis2.cat.com/#/service-detail?
serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false
https://sis2.cat.com/#/service-detail?serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false 3/6
22/9/2020 SIS 2.0
Illustration 9 g01243819
15. Remove bolts (21) and place filter assembly (22) to the side. Remove bolts (24) and
place manifold assembly (23) to the side.
Illustration 10 g01243665
16. Remove bolts (26) that retain transmission filler tube (25).
Illustration 11 g01243666
17. Remove clip (27) that retains transmission filler tube (25). Place transmission filler
tube (25) to the side.
Illustration 12 g01243674
18. Disconnect hose assembly (28). Remove clamp (29) and remove hose (30) from
the hydraulic oil tank.
19. Remove the transmission oil filter. Refer to Operation and Maintenance Manual,
"Transmission Oil Filter - Replace".
https://sis2.cat.com/#/service-detail?
serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false
https://sis2.cat.com/#/service-detail?serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false 4/6
22/9/2020 SIS 2.0
Illustration 13 g01243675
20. Attach Tooling (D) to transmission assembly (31). The weight of the transmission
assembly (31) is approximately 255 kg (562 lb).
Illustration 14 g01243826
21. Remove bolts (32) and cover (33). Remove bolts (34).
Illustration 15 g01243827
Illustration 16 g01243966
23. Place a suitable cable strap (37) around drive plate (38) for the converter.
https://sis2.cat.com/#/service-detail?
serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false
https://sis2.cat.com/#/service-detail?serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false 5/6
22/9/2020 SIS 2.0
Illustration 17 g01243880
Illustration 18 g01243894
24. Remove nuts (41) and (45). Remove bolts (42) and (46). Remove mounting bolts
(39) and (44) and remove mounts (40) and (43) from each side of transmission
assembly (31).
Illustration 19 g01244138
PIP-11107577
2020/09/22
14: 17: 57-05: 00
i02489286
© 2020 Caterpillar Inc.
https://sis2.cat.com/#/service-detail?
serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false
https://sis2.cat.com/#/service-detail?serialNumber=SHA&ieSystemControlNumber=i02489286&mediaNumber=RENR6475&infoType=-1&hideDocumentStructure=false 6/6