Está en la página 1de 91

1

REPETIDOR Y PUNTO DE ACCESO


INALÁMBRICO DE 150Mbps 802,11n
COM-817

Gracias por la compra de este producto Steren.

Este manual contiene todas las indicaciones necesarias para manejar su


nuevo Repetidor y punto de acceso inalámbrico de 150Mbps 802,11n.

Por favor, revíselo completamente para estar seguro de cómo utilizar


apropiadamente el producto.

Para apoyo, compras y todo lo nuevo que tiene Steren,


visite nuestro sitio web:

www.steren.com.mx

La información que se muestra en este manual sirve únicamente


como referencia sobre el producto. Debido a actualizaciones pueden
existir diferencias.
Por favor, consulte nuestra página web (www.steren.com.mx) para
obtener la versión más reciente del instructivo.

2
CONTENIDO

1.- CARACTERÍSTICAS 4

2.- INSTALACIÓN DEL HARDWARE  5

3.- CONFIGURAR EL EQUIPO 9

4.- CONFIGURACIÓN DEL REPETIDOR  16


4.1 Status (Estado)  16
4.2 Quick Setup (Configuración rápida)  18
4.3 WPS Settings (Configuración WPS) 20
4.4 Network (Red) 22
4.5 Wireless (Inalámbrico)  25

5.- SOLUCIÓN DE PROBLEMAS  40

6.- ESPECIFICACIONES 43

3
1.- CARACTERÍSTICAS
El repetidor y punto de acceso inalámbrico con puertos LAN y WAN,
permite crear una red alámbrica e inalámbrica (transmisión de hasta
150 Mbps), cumpliendo con los protocolos estándar de autentificación y
seguridad, incorpora un botón para activar/desactivar la función WPS.

Puede usarse para compartir una conexión de Internet e interconectarse


con dispositivos de menor velocidad o estándar anteriores (802,11b y
802,11g).

• Antena omni-direccional.
• 4 puertos LAN 10/100M de auto-negociación MDI/MDIX.
• 1 puerto WAN 10/100M de auto-negociación MDI/MDIX.
• Transmisión inalámbrica de rango extendido.
• Soporta PPPoE, L2TP, IP dinámica, IP estática.
• Conexión automática, sobre demanda.
• Soporta UPnP, WDS, ruteo estático, enlace con VPN.
• Soporta servidor virtual, aplicaciones especiales y DMZ host ideal para
hospedaje de páginas Web desde la red LAN.

4
• Soporta SSID broadcast control y control de acceso desde listas de MAC
address.
• Firewall integrado con funciones de filtrado de IP, MAC, y URL.
• Servidor DHCP con asignación automática de direcciones IP dinámicas.
• Soporta 64/128 bit WEP, WPA y WPAZ.

2.- INSTALACIÓN DEL HARDWARE


2.1. Requisitos del sistema

Requisitos mínimos:

Conexión de banda ancha (DSL / Cable) y servicio de módem con puerto


Ethernet.

Adaptador inalámbrico 802.11nb/g/n o un adaptador Ethernet y cable


para cada equipo.

Internet Explorer ® 5.0, Firefox ® 2.0 o Safari ® 1.4 o superior.


5
2.2. Indicadores y conexiones

LED Función
SYS Encendido o apagado Anormal
constantemente
Parpadeando Normal
WAN Enc Conexión WAN normal
Parpadeando Transmitiendo datos
Apag Conexión WAN anormal
LAN Enc Conexión LAN normal
Parpadendo Transmitiendo datos
Apag Conexión LAN anormal

6
Panel trasero

Descripción Función
PWR Adaptador de energía - no utilice un adaptador de corriente que no
sea el incluido ya que puede dañar el dispositivo.
LAN Conecte con el dispositivo NIC o Ethernet de la computadora.
WAN Conecte con el cable del módem.
RESET Restablecer los valores por defecto.

7
2.3. Procedimientos de instalación de hardware
Para conectar el repetidor Inalámbrico, tome como referencia la siguiente
imagen:

1 2 3 4 WAN WLAN SYS POWER WPS

Conecte un extremo del cable Ethernet al puerto Ethernet de su computadora


y el otro extremo a uno de los puertos LAN del repetidor.

Conecte otro cable Ethernet del módem de cable / DSL al puerto WAN del
repetidor.

Conecte el adaptador de corriente al enchufe en la parte trasera del repetidor


y a una toma de CA.
8
2.4. Restaurar valores predeterminados de fábrica
Si el repetidor se congela en un proceso de cambio de opción, si no puede
acceder a él porque no puede recordar la IP asignada o cualquier otro
problema, quizás tenga que utilizar el botón de “RESET” en la parte posterior
del repetidor para regresar a la configuración de fábrica. Mantenga pulsado este
botón durante unos segundos (2-6) con un lápiz cuando se está trabajando,
suelte y se restaurará la configuración de fábrica.

La otra forma de restaurar la configuración de fábrica es a través de la


interfaz de usuario utilizada en la instalación. Haga clic en “System
management’-” Reset “, y haga clic en el botón “Reset”.

3.- CONFIGURAR EL EQUIPO


Puede administrar el repetidor Inalámbrico a través de la utilidad de
configuración basada en navegador Web.

Para configurar el dispositivo a través del navegador Web, por lo menos un


equipo configurado correctamente se debe conectar al dispositivo a través de
Ethernet o red inalámbrica.

El repetidor Inalámbrico está pre configurado con la dirección IP 192.168.1.1,


la máscara de subred 255.255.255.0 y está habilitado el servidor DHCP
de forma predeterminada. Antes de configurar el repetidor, asegúrese de
que sus computadoras están configuradas para obtener una dirección
IP automáticamente desde el repetidor siguiendo los pasos mostrados a
continuación.
9
3.1 Configuración

3.1.3. Windows XP

1. Abra “Mi PC” en el escritorio o desde el menú


“Inicio”. Haga clic derecho en “Mis sitios de
red” en el menú “Otros sitios” a la izquierda y
seleccione “Propiedades”. Haga clic derecho
sobre “Conexión de Área Local” en la ventana
que aparece y seleccione “Propiedades”.

2. En la ventana que aparece, debajo de “Esta


conexión utiliza los siguientes elementos:”
seleccione “Protocolo Internet (TCP / IP)” y haga
clic en el botón “Propiedades” situado en la parte
inferior.

3. Elija “Obtener dirección IP automáticamente”


y “Obtener dirección del servidor DNS
automáticamente” y, a continuación, pulse
Aceptar para cerrar las “Propiedades del
protocolo de Internet (TCP / IP)”.

4. Pulse Aceptar para cerrar la ventana de “Propiedades de Conexión de Área


Local”.

10
3.1.4. Windows Vista

1. Ir a “Inicio → Panel de control”.

2. Haga doble clic en “Centro de


redes y recursos compartidos”.

3. Haga clic en “Administrar


conexiones de red” o “Cambiar
configuración del adaptador”.

4. Haga clic derecho sobre el icono de


“Conexión de área local” y seleccione
“Propiedades”.

5. Seleccione “Protocolo de Internet versión


4 (TCP / IP)” y haga clic en el botón
“Propiedades”.

6. Seleccione “Obtener dirección IP automáticamente”


y “Obtener dirección del servidor DNS automáticamente”
y, a continuación, pulse Aceptar para cerrar las
“Propiedades del protocolo de Internet (TCP / IP)”.

11
7. Pulse Aceptar para cerrar la
ventana “Propiedades de la conexión
de área local”.

3.2. Comprobación de la conexión al repetidor

Después de configurar el protocolo TCP / IP, utilice el comando ping para


comprobar si el equipo puede comunicarse con el repetidor. Para ejecutar el
comando ping, abra la ventana de DOS y ejecute el comando “ping” a la
dirección IP del repetidor Inalámbrico:

Para Windows 98/Me: Inicio → Ejecutar. Escriba “command” y haga clic en


Aceptar.
Para Windows 2000/XP: Inicio → Ejecutar. Escriba cmd y haga clic en
Aceptar.
Para Windows Vista / 7 Inicio → Accesorios → Símbolo del sistema.

En el DOS, escriba el siguiente comando: “ping 192.168.1.1”

12
La ventana de comandos debe mostrar algo similar a lo siguiente:

C:\Documents and Settings\admin>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time=1ms TTL=64


Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64

Ping statistics for 192.168.1.1:


Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 1ms, Average = 1ms

Si el equipo no puede conectar con el repetidor, la ventana de comandos


devolverá lo siguiente:

C:\Documents and Settings\admin>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out.


Request timed out.
Request timed out.
Request timed out.

Ping statistics for 192.168.1.1:


Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Verifique la configuración del equipo de red es correcta y compruebe la


conexión entre el repetidor y el ordenador.
13
3.3. Entrar a la interfaz del repetidor

Abra un navegador web (Safari, Internet Explorer, etc) en el equipo que


acaba de conectar al repetidor, escriba http://192.168.1.1 en la barra de
direcciones, y pulse ENTER.

En la ventana, introduzca su nombre de usuario


y la contraseña (guest/guest), y después de clic en
OK.

Después de que se haya registrado,aparecerá la interfase de usuario.


El menú de la izquierda muestra las opciones para configurar el sistema, la
pantalla derecha es la información resumida para ver y ajustar las
configuraciones.
14
Después de haber iniciado la sesión, la interfaz del repetidor aparecerá
en la pantalla. El menú de la izquierda muestra las principales opciones para
configurar el sistema y la pantalla de la derecha, es el resumen de
información para la visualización y ajuste de las configuraciones.

15
4.- CONFIGURACIÓN DEL REPETIDOR
4.1 Status (Estado)
Esta característica proporciona
información detallada sobre el
estado del repetidor.

4.1.1 Version (Versión)


Muestra el hardware y la versión del firmware.

4.1.2 WAN
Esta opción proporciona la información de estado de ejecución del
puerto WAN (el puerto que se conecta a Internet).

- Connection Type (Tipo de conexión): Muestra el tipo de conexión actual.


Puede ser “PPPoE”, “DHCP”, “Static IP”, según el tipo de conexión de su
proveedor de Internet ofrece.
- Physical Address (Dirección Física): La dirección física del puerto WAN es una
dirección única asignada por el fabricante.
- IP Address (Dirección IP): La dirección IP que obtuvo después de conectarse a
Internet, si no se ha conectado a Internet, este campo será 0.0.0.0.
- Subnet mask (Máscara de subred): La máscara de subred se obtiene después
de conectarse a Internet, si no se ha conectado a Internet, este campo es 0.0.0.0.
- Default Gateway (Puerta de enlace predeterminada): La dirección IP de Puerta de
enlace predeterminada que obtuvo después de conectarse a Internet, si no se ha
conectado a Internet, este campo es 0.0.0.0.
- Primary DNS (DNS primaria): El servidor DNS traduce nombres de dominio o sitio
web a la dirección IP. Introduzca la dirección del servidor DNS que usted utilice o
16 la proporcionada por su proveedor de servicios.
- Secondary DNS (DNS secundario): Introduzca la dirección IP de un servidor DNS de
respaldo o se puede dejar este campo en blanco.
- Link Status (Estado de la conexión): Muestra el estado actual de la información del
vínculo. Usted puede elegir conectar o desconectar de forma manual.

4.1.3. LAN
Esta opción proporciona información acerca del puerto LAN del repetidor, la
dirección física, la dirección IP y la situación actual del servidor DHCP.

4.1.4. Wireless (Inalámbrico)


Este apartado proporciona información actual del funcionamiento de la señal
inalámbrica.

- Wireless status (Estado inalámbrico): Muestra el estado de la interfaz inalámbrica.


- Nombre (SSID): SSID (Service Set Identifier) es el nombre de su red inalámbrica
compartida entre todos los puntos de una red inalámbrica.
- Mode (Modo): el modo inalámbrico actual del repetidor.
- Channel (Canal): canal de visualización actual de repetidor.
- MAC Address (Dirección MAC): La dirección MAC se utiliza para la comunicación
inalámbrica.
- WPS Status (Estado WPS): muestra si el WPS Display (Wi-Fi Protected Setup) está
habilitado o no.

4.1.5 Repeater Status (Estado del repetidor)


Esta opción proporciona información del sistema.

4.1.6 Traffic Statistics (Estadísticas de Tráfico)


Esta sección proporciona información estadística acerca de los datos
enviados y recibidos por el repetidor.

17
4.2 Quick Setup (Configuración rápida)
El propósito de esta opción es proporcionar
una manera fácil para utilizar y configurar el
repetidor para acceder a Internet de manera
rápida; aquí se puede configurar la manera de
asignar las direcciones IP, incluyendo “DHCP
(dinámica)”, “PPPoE”, “estática” y “Configuración
inalámbrica”.
Esta es la herramienta más conveniente para configurar repetidor.

4.2.1 DHCP (dinámica)


Después de seleccionar esta opción, obtendrá una dirección IP de su
proveedor de Internet de forma automática. Los ISP que proporcionan el
servicio por cable casi siempre utilizan la tecnología de DHCP.

4.2.2 PPPoE
Si su ISP le proporciona el servicio de PPPoE (la mayoría de los ISP de
ADSL proporcionan este servicio), por favor seleccione esta opción. En
la “configuración conveniente” Puede introducir su nombre de usuario y
contraseña PPPoE para acceder a Internet.

- PPPoE Username (Nombre de usuario PPPoE): PPPoE nombre de usuario de


entrada proporcionada por el ISP
- PPPoE Password (Contraseña PPPoE): contraseña de entrada PPPoE
proporcionada por el ISP.

4.2.3 Static (Estática)


Esta sección sólo debe usarse cuando los usuarios utilizan una
dirección IP estática para acceder a Internet. Usted deberá ingresar
su “dirección IP WAN”, “la máscara de subred”, “puerta de enlace
predeterminada” y “servidor DNS (Domain Name Server)”, de acuerdo a
la información proporcionada por el ISP.
18
Cada dirección IP debe ser única y dividida en cuatro números separados
por el signo “.”.

- WAN IP address (Dirección IP WAN): La dirección IP para el acceso a Internet.


- Subnet mask (Máscara de subred): especifique una máscara de subred para el
segmento WAN.
- Default gateway (Puerta de enlace predeterminada): Es proporcionada por el ISP.
- Primary DNS (DNS primario): el servidor DNS se utiliza para resolver nombres de
dominio. Su ISP le proporciona al menos una dirección IP DNS, introducir la dirección
IP del servidor DNS en este campo.
- Secondary DNS (DNS Secundario): Introduzca la dirección IP del servidor DNS de
respaldo, o puede dejar este campo en blanco.

4.2.4 Wireless Configuration (Configuración inalámbrica)


Puede elegir la opción “Habilitar” o “Desactivar” para activar o desactivar la
función inalámbrica. El valor predeterminado es “habilitar”. Si elige la opción
“Desactivar” el estado, el repetidor se convertirá en un repetidor de banda
ancha por cable sin la función inalámbrica, así que tenga cuidado al elegir
este estado.

- SSID: SSID (Service Set Identifier) es el nombre compartido entre todos los puntos
de una red inalámbrica. El SSID debe ser idéntico para todos los dispositivos de la
red. Distingue entre mayúsculas y minúsculas y no debe exceder los 32 caracteres.
Asegúrese de que todos los puntos de la red inalámbrica tengan el mismo SSID. Para
mayor seguridad, debe cambiar el SSID.
- Region (Región): Seleccione una región que se ajuste al entorno de uso.
- Channel (Canal): el repetidor inalámbrico se comunica con las tarjetas inalámbricas
en un determinado canal, que puede reducir la interferencia entre los diferentes ca-
nales.
- Authentication Type (Tipo de autenticación): Diferentes tipos de autenticación
utilizan diferentes tipos de encriptación, lo que puede cifrar los datos para proteger sus
19
4.2.5 MAC Clone (Clon MAC)
El puerto WAN del repetidor tiene una dirección MAC única asignada
por el fabricante, llamada “MAC por defecto”. El “Clon MAC” se utiliza
para algunas situaciones especiales, por ejemplo, si el proveedor sólo
permite ciertas direcciones MAC para acceder a Internet, entonces
podrá modificar la dirección de su puerto WAN MAC, de acuerdo a lo
que el ISP requiera, y así evitar la detección del nombre del ISP.

4.3 WPS Settings (Configuración WPS)


La Configuración Protegida de Wi-Fi
(WPS) puede ayudarle a crear una
red segura con facilidad. Usted
puede usar “Configuración de
entrada de PIN” o “Usar botón (PBC)”
para encriptar la red. Este repetidor
también cuenta con un botón WPS.

Basta con pulsar este botón en el repetidor y la tarjeta de red inalámbrica que
soporten la función WPS, para que la señal del repetidor sea codificada para
WPA2-AES automáticamente.

Nota:
Si ha configurado el modo de encriptación en el repetidor, entonces cuando se
utilice la función WPS, configure el tipo de autenticación en ninguno, para que la
señal sea codificada en WPA2-AES de forma automática. Si no desea cambiar el
tipo de autenticación, cuando se utiliza esta función, el repetidor se puede cifrar
en el modo que ha configurado.

20
4.3.1 WPS Settings (Configuración WPS)
- WPS Status (Estado de WPS): Puede utilizar esta función para configurar
la conexión inalámbrica entre el repetidor y la tarjeta de red inalámbrica. El
valor predeterminado es Activado.
- AP PIN Code (AP Código PIN): Este código sirve para identificar el
dispositivo inalámbrico.
- Add A New Device (Agregar un nuevo dispositivo): Agregar un nuevo
dispositivo de WPS.

4.3.2 Add A New Device (Agregar un nuevo dispositivo)


- Enter the new device’s PIN (Introducir el nuevo PIN del dispositivo): Este
código debe estar impreso en el nuevo dispositivo inalámbrico.
- Press the button of the new device in two minutes (Pulse el botón del nuevo
dispositivo en los siguientes dos minutos): el nuevo dispositivo enviará un
código PIN al repetidor inalámbrico.
El botón WPS se puede conectar un adaptador inalámbrico y el repetidor
de forma segura. Si usted tiene una tarjeta de red inalámbrica que tiene
el botón WPS, puede configurar una red segura a través de los siguientes
métodos.

Método 1:
1.- Pulse el botón WPS en el repetidor hasta que el LED SYS parpadee en amarillo.
2.- Pulse el botón WPS en la tarjeta de red inalámbrica por cerca de 3-5 segundos.
3.- La conexión segura se establecerá automáticamente.

Método 2:
1.- Introduzca el código PIN de la página del adaptador WPS en la página de
configuración WPS del repetidor y haga clic en “conectar”.
2.- Presione “Configuración de entrada de PIN” en la configuración de protección de
Wi-Fi del adaptador. 21
3.- Seleccione el repetidor en la ventana emergente, haga clic en ‘Select’
4.- La conexión entre el adaptador y el repetidor se establecerá automáticamente.

Método 3:
1.- Seleccione “Input PIN from AP (entrada del PIN del AP)” en la página de
configuración de protección WI-FI, ingrese el PIN del repetidor y haga clic en “PIN
Input Config (Configuración de entrada del PIN)”.
2.- Seleccione el repetidor en la ventana emergente, haga clic en ‘Select’.
3.- La conexión entre el adaptador y el repetidor es establecer de forma automática.

Nota: Si hay más de un AP en el modo PBC cuando se utiliza el


método 1, no habrá superposición de sesiones. Cuando use los métodos 2
ó 3 espere un tiempo para pulsar el botón otra vez.

4.3.3 WPS Configuration (Configuración WPS)


Muestra la información de configuración WPS.

4.4 Network (Red)


4.4.1 WAN
Este elemento proporciona
dos tipos de acceso para
configurar los parámetros
WAN.
Estos son: acceso por cable e
inalámbrico.

22
4.4.1.1. Wired Access (Acceso por cable)
- Internet Access Type (Tipo de Acceso a Internet): Pregunte a su ISP para obtener el
tipo de acceso correcto.
- IP: La dirección IP que obtuvo después de conectarse a Internet, si no se ha
conectado a Internet, este campo es 0.0.0.0.
- Subnet Mask (Máscara de subred): La máscara de subred se obtiene después de
conectarse a Internet, si no se ha conectado a Internet, este campo es 0.0.0.0.
- Gateway (Puerta de enlace): La dirección IP de Puerta de enlace predeterminada
que obtuvo después de conectarse a Internet, si no se ha conectado a Internet, este
campo es 0.0.0.0.
- MTU: la MTU (Maximum Transmission Unit) especifica el tamaño de paquete más
grande permitido para la transmisión en la red. La mayoría de los usuarios de DSL
deben utilizar 1492. El valor MTU puede ser configurado de forma manual y debe estar
en el rango 1200 a 1500. Si el valor establecido no es igual al valor del ISP, es posible
que cause algunos problemas, tales como evitar el envío de correo electrónico o no
permitir la entrada a una página web. Si esto sucede, usted puede contactar a su ISP
para obtener más información y corregir el valor MTU de su repetidor.
- Primary DNS (DNS primario): El servidor DNS traduce nombres de dominio o sitio web
en la dirección IP, introduzca la dirección del servidor DNS proporcionada por su ISP.
- Primary DNS (DNS secundario): Introduzca la dirección IP de un servidor DNS de
respaldo o puede dejar este campo en blanco.

4.4.1.2 Wireless Access (Acceso inalámbrico)


- SSID: SSID (Service Set Identifier) es el nombre de su red inalámbrica compartida
entre todos los dispositivos de una red inalámbrica. El SSID debe ser idéntico para
todos los dispositivos de la red. Se distingue entre mayúsculas y minúsculas y no debe
exceder los 32 caracteres. Asegúrese de que todos los puntos de la red inalámbrica
tengan el mismo SSID. Para mayor seguridad, debe cambie el SSID lo antes posible.
- Authentication Type (Tipo de autenticación): “Ninguno” significa que los datos
inalámbricos no están encriptados.
23
- Internet Access Type (Tipo de Acceso a Internet): Pregunte a su ISP para obtener el
tipo correcto de acceso.
- IP: La dirección IP que obtuvo después de conectarse a Internet, si no se ha
conectado a Internet, este campo es 0.0.0.0.
- Subnet Mask (Máscara de subred): La máscara de subred se obtiene después de
conectarse a Internet, si no se ha conectado a Internet, este campo es 0.0.0.0.
- Gateway (Puerta de enlace): La dirección IP de Puerta de enlace predeterminada
que obtuvo después de conectarse a Internet, si no se ha conectado a Internet, este
campo es 0.0.0.0.
- MTU: El valor MTU (Maximum Transmission Unit) especifica el tamaño de paquete
más grande permitido para la transmisión de la red. La mayoría de los usuarios de
DSL deben utilizar el 1492.Este valor se puede configurar de forma manual, y debe
estar en el rango de 1200 a 1500. Si el valor establecido no es igual al valor del ISP,
es posible que cause algunos problemas, tales como no permitir el envío de correo
electrónico, o la apertura de páginas web. Si esto sucede, puede contactar a su ISP
para obtener más información y corregir el valor MTU de su repetidor.
- Primary DNS (DNS primario): El servidor DNS traduce nombres de dominio o sitio
web en la dirección IP, introduzca la dirección del servidor DNS proporcionada por
su ISP.
- Secondary DNS (DNS secundario): Introduzca la dirección IP de un servidor DNS de
respaldo o puede dejar este campo en blanco.

4.4.2 LAN
La dirección IP del puerto LAN se utiliza para accesar directamente al
repetidor desde los ordenadores conectados al él. En esta sección podrá
configurar la dirección IP que necesite.

El formato de dirección IP es ***.***.***.*** y la dirección IP por defecto es


192.168.1.1, la máscara de subred predeterminada es 255.255.255.0.
24
4.4.3 MAC Clone (Clon MAC)
El puerto WAN del repetidor tiene una dirección MAC única asignada por
el fabricante, llamada “MAC por defecto”. El “Clon MAC” se utiliza para
algunas situaciones especiales, por ejemplo, si el proveedor sólo permite
ciertas direcciones MAC para acceder a Internet, entonces podrá modificar
la dirección MAC del puerto WAN, de acuerdo a lo que el ISP requiera, y así
evitar la detección del nombre del ISP.

4.4.4 Port Settings (Configuración del puerto)


Aquí se pueden establecer que las interfaces WAN y LAN del repetidor
funcionen en los modos de comunicación 100M duplex, 100M half-duplex,
10M duplex y 10M half-duplex.

4.4.5 IGMP Proxy (Proxy IGMP)


Aquí puede configurar el proxy IGMP como “Activado” o “Desactivado”.

4.5 Wireless (Inalámbrico)


4.5.1. Wireless Settings (Configuración
inalámbrica)
Esta sección proporciona los elementos
básicos de configuración para usuarios
repetidor inalámbrico, incluyendo “estado
de la red inalámbrica”, “SSID”, “Banda de
Radio”, “Modo de Radio”, “MAC”, “difusión
de SSID”, “ancho de banda”, “Banda
lateral”, “ Región “y” Canal “y varios
elementos de configuración básica.
25
- Wireless network status (Estado de la red inalámbrica): El usuario puede elegir
la opción “activar” o “desactivar”. Si usted elije “Desactivar”, la función de AP del
repetidor inalámbrico se apagará.
- SSID: El valor predeterminado es trst1.
- Radio band (Banda de radio): Puede seleccionar los estándares inalámbricos
funcionando en la red, si tiene dispositivos de la red Wireless-N y Wireless-B /G,
mantenga la configuración por defecto, 802.11b+g+n.
- Radio mode (Modo de radio): Puede seleccionar el modo de radio de repetidor
inalámbrico, que son punto de acceso, Cliente, AP + WDS y WDS. El valor
predeterminado es el modo de AP.
- MAC: La dirección física del repetidor inalámbrico.
- SSID Broadcasting (Difusión del SSID): Usted puede seleccionar “habilitar” o
“desactivar” para activar o desactivar la función de difusión del identificador SSID.
Si la configuración de este campo se deshabilita, los clientes inalámbricos no podrán
obtener este SSID para iniciar sesión, el usuario tendrá que introducir el SSID
manualmente.
- Channel width (Ancho de Banda): Esta opción permite configurar el ancho de banda
inalámbrica del repetidor. 20 MHz: En este modo se puede conseguir bajo ancho de
banda, menor interferencia y ritmo lento. 40 MHz: En este modo se puede obtener
gran ancho de banda, con mucha interferencia y velocidad. Use sólo cuando usted
tiene una red inalámbrica 802.11n.
- Channel sideband (Banda lateral del canal): Controla el repetidor inalámbrico para
usar el canal superior o inferior cuando se trabaja en 40MHz.
- Region (Región): seleccione la región en la que vive.
- Channel (Canal): En 20 MHz, se puede seleccionar un canal de 1 a 13 de forma
manual, y en 40 MHz, puede seleccionar un canal del 1 al 9 ó 5 a 13, lo que le
permitirá evitar interferencias.

26
4.5.2 Wireless Security (Seguridad inalámbrica)
El punto le permite encriptar sus comunicaciones inalámbricas, y también
puede proteger su red inalámbrica de acceso de usuarios no autorizados.
Que suministra “Ninguna”, “WEP”, “WPA-PSK”, “WPA2-PSK” y “WPA/
WPA2-PSK” cinco modos de cifrado diferente.

4.5.2.1 None (Ninguna)


“Ninguno” significa que los datos inalámbricos no están encriptados.

4.5.2.2 WEP
- Key Length (Longitud de clave): Hay dos niveles básicos de encriptación WEP de
64 bits y 128 bits, mientras más bits tenga la contraseña, mayor será la seguridad, al
mismo tiempo, la velocidad de transmisión de datos inalámbrica es más lenta.
- Key Mode (Modo de contraseña): Si selecciona WEP para cifrar sus datos, elija los
bits de la contraseña, debe ser de 64 ó 128 bits. A continuación, seleccione el formato
de la contraseña, que debe ser hexadecimal o ASCII. El formato válido para la contra-
seña hexadecimal debe ser números del 0 al 9 y letras de la A a la F. Los caracteres
pueden ser letras y números mezclados. El modo ASCII admite todos los caracteres
del teclado.
- Key Length description (Descripción de longitud de la contraseña): Cuando seleccione
64 bits, debe introducir 10 caracteres para HEX y 5 caracteres de ASCII, y cuando se
selecciona 128 bits, debe introducir 26 caracteres para HEX y 13 caracteres de ASCII.

Nota: Cuando el WPS está habilitado, no utilice WEP.

4.5.2.3 WPA-PSK
- Encryption type (Tipo de cifrado): Puede seleccionar el algoritmo que desea
utilizar, TKIP, AES o TKIP y AES. TKIP significa “Temporal Key Integrity Protocol”, que
incorpora el Código de Integridad del mensaje (MIC) para brindar protección contra los
piratas informáticos. AES, significa “sistema de cifrado avanzado”, que utiliza un bloque
de datos simétrico de 128 bits.
27
- Key Renewal (Renovación de la clave): se puede configurar el tiempo de renovación
entre 60 y 86400 segundos.
- Key Length description (Descripción de longitud de la clave): es necesario de entrada
de 8 a 63 caracteres ASCII, independientemente del tipo que usted elija.

4.5.2.4 WPA2-PSK
El WPA2-PSK es similar a WPA-PSK, pero el método de cifrado es aún más
seguro. Si va a utilizar WPA2-PSK, deberá introducir la contraseña (en el
rango de 8 a 63 caracteres) y el tiempo de renovación de la clave (dejar este
valor en el rango de 60 a 86400 segundos).

4.5.2.5 WPA/WPA2-PSK
Este modo mezcla los modos WPA-PSK y WPA2-PSK, lo que proporciona
un mayor nivel de seguridad. Se puede configurar de acuerdo con WPA-PSK
o WPA2-PSK.

4.5.3 Filtrado de direcciones MAC inalámbricas


- MAC Filter Status (Estado del filtro MAC): el valor por defecto es “desactivado”.
Puede filtrar los usuarios con conexión de cable usando esta función; los usuarios no
autorizados no podrán acceder a la red.
- Description (Descripción): aquí podrá describir la lista de filtros MAC para diferenciarla
de otras listas.
- Rule (Regla): se puede seleccionar permitir o denegar. El valor predeterminado es
permitir.
- MAC address (Dirección MAC): introducir la dirección MAC que desea controlar. El
formato predeterminado es **-**-**-**-**-** (por ejemplo: 00-22-33-da-cc-bb).

5.5.4 WDS
4.5.4.1 Configuración WDS
Si seleccionó WDS o AP + WDS en el modo básico de radio inalámbrico,
realice las siguientes configuraciones.
28
- WDS Name (Nombre WDS): Dé una descripción de su puente inalámbrico.
- WDS MAC Address (Dirección MAC WDS): Si el modo actual es “WDS” o “AP +
WDS”, entonces necesitará configurar el puente inalámbrico. Introduzca la dirección
MAC del punto de acceso remoto. El punto de acceso remoto también se tendrá que
configurar en el modo “WDS” o “AP + WDS”.
- Current WDS Information (Información actual WDS): Se muestra la información básica
de todos los puentes inalámbricos que estén en estado de conexión, puede eliminar
los puentes innecesarios.

AP1:
- Seleccione el modo de radio WDS o WDS + AP inalámbrico en gestión básica de la
AP1.
- Haga clic en ‘Wireless-Management’’- “AP-Setup”- “Seguridad” y seleccione y guarde
“Ninguno” como el tipo de autenticación.
- Haga clic en ‘Wireless-Management’’ AP-Setup’ “ Security “ y seleccione y guarde
“None” como el tipo de autenticación WDS o seleccione un tipo de seguridad WDS,
ingrese la contraseña y guarde.
- Introduzca el nombre de WDS (por ejemplo: default), ingrese la dirección MAC del
AP2 (00-22-4f-bc-af-5d), haga clic en Add, a continuación, el registro de nombre por
defecto aparecerá en la lista WDS.
- El canal seleccionado es ‘Canal 6’ en la gestión básica inalámbrica de la AP2.

AP2:
- El modo de radio seleccionado debe WDS o AP + WDS inalámbrico en gestión básica
de la AP2.
- La dirección AP2IP debe ser 192.168.1.x (1<x<255, por ejemplo: x = 8).
- Dentro de ‘LAN-setup’-’DHCP server ‘, seleccione deshabilitar el servidor DHCP.
- Introduzca el nombre WDS (por ejemplo: Default) y la dirección MAC del AP1
(00-22-4f-cc-ae-f5), haga clic en Agregar. El nombre guardado aparecerá en la lista
WDS.
- Seleccione ‘Canal 6’ en la configuración inalámbrica básica de la AP2.

Nota: Antes de configurar la conexión WDS, por favor asegúrese de que


AP1 y AP2 se encuentran en la misma red, es decir, si la dirección IP de la
AP1 es 192.168.1.1, la dirección IP de la AP-2 debe ser 192.168.1.x (1 < x
<255, por ejemplo: x = 8).
29
El modo de repetidor inalámbrico se utiliza para retransmitir la señal
inalámbrica de un punto de la red al siguiente, amplificarla y formar una
nueva área de cobertura inalámbrica.

AP1:
- Seleccione el modo de radio “ Access Point (punto de acceso)” en la configuración
básica inalámbrica de la AP1.
- Seleccione “Canal 6” en la configuración inalámbrica básica de la AP1.

AP2:
- Seleccione el modo de radio “ REPEATER (REPETIDOR)” en inalámbrica gestión
básica de AP2.
- Seleccione SSID Repetidor es “Netis1” en configuración inalámbrica básica de AP2.
- Seleccione ‘Canal 6’ en configuración inalámbrica básica del AP2.
- La dirección IP de la AP-2 debe ser 192.168.1.x (1 <x <255, por ejemplo: x = 8).
- Seleccione ‘LAN-setup’-’DHCP servidor’, seleccione deshabilitar el servidor DHCP.

AP3:
- Seleccione el modo de radio “ REPEATER (REPETIDOR)” en gestión básica
inalámbrica de AP3.
- Seleccione el SSID del repetidor “Netis1” en configuración inalámbrica básica de AP2.
- Seleccione ‘Canal 6’ en configuración inalámbrica básica del AP2.
- La dirección IP de la AP-2 debe ser 192.168.1.x (1 <x <255, por ejemplo: x = 8).
- Seleccione ‘LAN-setup’-’DHCP servidor’, seleccione deshabilitar el servidor DHCP.

4.5.5. Wireless Advanced (Inalámbrica avanzada)


Estos ajustes son sólo para los usuarios más avanzados técnicamente
que tienen un conocimiento suficiente acerca de la LAN inalámbrica. Estos
ajustes no se debe cambiar a menos que sepa el efecto que el cambio
tendrá en la AP.
30
- Authentications type (Tipo de Autenticación): el valor por defecto es “Auto”, puede
seleccionar “sistema abierto” o “Shared Key” como la autenticación que se utilizará.
Seleccione “Shared Key (contraseña compartida)” si sólo desea utilizar “Shared Key”
como autenticación (el emisor y el receptor utilizan una misma clave WEP para la
autenticación).
- Beacon Interval (Intervalo de Beacon): el intervalo de tiempo de este repetidor para
la transmisión de un beacon. Éste se utiliza para sincronizar la red inalámbrica. El
intervalo válido es de 20 a 1000, el valor por defecto es 100.
- RTS Threshold (Umbral RTS): usted puede establecer el valor del umbral RTS en
este campo, el rango válido debe 256-2347 y el valor por defecto es 2347. Si un
paquete de red es más pequeño que el tamaño del umbral RTS preestablecido, el
mecanismo RTS / CTS no se habilitará.
- Aggregation (Agregación): puede acelerar la velocidad de transmisión inalámbrica
habilitando la función de agregación. El valor predeterminado es AMPDU + AMSDU.
- Fragmentation Threshold (Umbral de fragmentación): se especifica el tamaño
máximo del paquete durante la fragmentación de los datos que serán transmitidos.
- Fragmentation Threshold (Velocidad de transmisión): velocidad de transmisión indica
la velocidad de transmisión de acceso LAN inalámbrico. El valor por defecto es “Auto”
y se puede establecer este valor en el rango 1-54Mbps.
- ShortGi: usted puede seleccionar “Habilitar” o “desactivar” la función shortgi.
- Protection (Protección): utilizar el modo mixto de 802.11b y 802.11g pueden dar
lugar a un bajo rendimiento de la red. Al permitir la protección 802.11 se mejorará el
rendimiento de los dispositivos 802.11g en la red inalámbrica.
- Preamble Type (Tipo de preámbulo): “Preámbulo corto” es adecuado para redes
inalámbricas con el tráfico pesado. “Preámbulo largo” proporciona una fiabilidad de
comunicación mucho más, el valor por defecto es “Preámbulo largo”.

31
4.5.6. Wireless Statistics (Estadísticas inalámbricas)
Mostrar el estado actual de los clientes inalámbricos asociados con el AP.

4.5.7. Multiple AP Settings (Configuración de múltiples AP)


El estado por defecto de secundaria AP es desactivado, puede
seleccionar Activar para activar el AP secundario. Por favor, consulte
Configuración Rápida de Seguridad Inalámbrica y Estadísticas Inalámbricas
para obtener más detalles.

4.6. DHCP
4.6.1 DHCP Settings (Configuración de DHCP)

4.6.2 DHCP Clients List (Lista de clientes DHCP)


Muestra el estado de IP asignada por el servidor DHCP.

4.6.3 Address Reservation (Reserva de direcciones)


Address Reservation (Reserva de dirección): dirección IP reservada a la
dirección física del host. Si desea configurar una dirección IP fija para algún
host, deberá introducir la dirección física y dirección IP, hacer clic en Agregar.

4.7. Forwarding (Reenvío)

4.7.1 Virtual Servers (Servidores Virtuales)


- Description (Descripción): describir el punto actual del servidor virtual.
- Internal Host IP Address (Dirección IP interna del host): la “dirección IP interna del
host” indica la dirección IP del host interno que utiliza el servidor virtual.
- Protocol (Protocolo): el protocolo suministra a varios protocolos. Por ejemplo, si usted
dispone de un servidor web dentro de la LAN, usted puede seleccionar la plantilla de
HTTP, el repetidor usará el puerto 80 de entrada de forma automática.
- External Port (Puerto externo): ingrese un número de puerto de extranet (los usuarios
de Internet pueden ver estos puertos).
- Internal Port (Puerto interno): ingrese un número de puerto de intranet.
32
4.7.2 Port Triggering (Activación de puertos)
El módulo de activación del puerto registra dinámicamente las reglas de
servidor virtual cuando cualquier host IP genera un paquete del protocolo de
activación y puerto especificados. El módulo de activación del puerto usa el
protocolo de reenvío y número de puerto y usa la dirección IP del host que
genera el paquete de activación cuando se registra una regla.

- Predefined Trigger Rules (Reglas predefinidas de activación): seleccione una de las


reglas predefinidas.
- Rule Name (Nombre de la regla): describir el activador predefinido que va a configurar.
- Trigger Protocol (Protocolo de activación): puede seleccionar TCP / UDP.
- Trigger Port (Puerto de activación): se puede seleccionar un puerto de activación.
- Forward Protocol (Protocolo de reenvío): se puede seleccionar TCP / UDP.
- Forward Port (Puerto de Reenvío): puede seleccionar un puerto de reenvío.

4.7.3 DMZ
El DMZ abre todos los puertos de una computadora, exponiéndola al
Internet. Por esta razón sólo se debe utilizar para un propósito especial.
En esta función puede seleccionar “DMZ”, introducir la dirección IP del host
DMZ, hacer clic en “Guardar”. Por razones de seguridad, se sugiere el uso
de “prestador de servicios virtuales” en lugar de “DMZ”.

4.7.4 UPnP
La función UPnP soporta el registro del puerto de reenvío de carga de
aplicaciones de forma automática. Seleccione “Activar” para iniciar esta
función.

4.7.5 FTP Private Port (Puerto privado de FTP)


Algunos juegos, servidores y aplicaciones ya no funcionan cuando se
encuentran tras un repetidor NAT, por lo que esta función se realiza una
función de asignación de puertos de LAN a WAN.
33
4.8 Security (Seguridad)

4.8.1 Security Settings (Configuración de seguridad)


El VPN es usado comúnmente para encapsular y encriptar datos a través de
la red pública. Para el túnel VPN, el repetidor soporta transferencia IPSec,
PPTP y L2TP.

4.8.2 IP Address Filtering (Filtrado de Direcciones IP)

- Status (Estado): por defecto está desactivado.


- Description (Descripción): describa lista de cortafuegos de IP para diferenciarla de
otras listas de cortafuegos de IP.
- Rule (Regla): se puede seleccionar “permitir” o “denegar”. El valor predeterminado
es “permitir”.
- Source IP address (Dirección IP de origen): introduzca la dirección IP de origen que se
desea controlar. El formato predeterminado es ***.***.***.***( por ejemplo: 192.168.2.3).
- Protocol and Port (Protocolo y puerto): si la regla ya existe en el “modelo de
protocolo”. Usted puede seleccionar la opción adecuada y aplicarla. O puede escribir
la entrada del protocolo y el número de puerto de forma manual, haga clic en botón
“añadir”, el elemento se mostrará en la lista.

Siga los pasos siguientes para establecer control de acceso a Internet:

1.- Puede seleccionar “activar” y haga clic en “Guardar” para activar el


“Firewall de IP”. Esto es sólo el primer paso, usted debe seguir para crear
reglas adecuadas para el “Firewall de IP”.
2.- Ingrese la descripción de la regla actual de control de acceso en el
campo “Descripción”. De entrada de direcciones IP de host que desea
restringir.

34
3.- Hay dos elementos mostrados, “Dejar pasar por el repetidor para la
dirección IP en la lista, otras direcciones bloqueadas” y “Denegar el a través
del repetidor para la dirección IP en la lista, otras direcciones permitidas”,
seleccione el elemento que desee, y haga clic en botón “Guardar”.
4.- Si desea suprimir un punto determinado en la lista, seleccione el
elemento en la lista y haga clic en “Eliminar” para eliminarla.

4.8.3 MAC Filtering

- Status (Estado): por defecto está desactivado. Usando esta función puede filtrar los
usuarios con conexión de cable; los usuarios no autorizados no podrán acceder a la
red.
- Description (Descripción): Aquí podrá describir la lista de filtros MAC para
diferenciarla de otras listas, puede seleccionar permitir o denegar. El valor
predeterminado es permitir.
- MAC address (Dirección MAC): introduzca la dirección MAC que desea controlar. El
formato predeterminado es **-**-**-**-**-** (por ejemplo: 00-22-33-da-cc-bb).

Siga los pasos siguientes para configurar el filtro MAC:

1. Habilitar el filtro de MAC, a continuación, seleccione Guardar.

2. Agregue la dirección MAC que desea controlar en la “dirección MAC”


de campo (el formato es **-**-**-**-**-**), haga clic en “Añadir”, y verá la
dirección MAC en la lista.

3. Se muestran dos opciones, “Permiso de conexión inalámbrica para la


dirección MAC de la lista (los demás se les niega)” y “Denegar la conexión
inalámbrica para la dirección MAC de la lista (los demás son permitidos)”,
seleccione el elemento que desee, y haga clic en el botón “Guardar”.
35
4.8.4 Domain Filtering (Filtrado de Dominios)

- Status (Estado): por defecto está desactivado. La función “filtro DNS” es capaz de
filtrar el nombre de un dominio determinado, como www.sina.com.

- Rule (Regla): se puede seleccionar permitir o denegar. El valor predeterminado es


permitir.

- DNS Filter Key words (Palabras clave del filtro DNS): Escriba el nombre del sitio Web
o el nombre de dominio en el campo “Palabras clave DNS “, por ejemplo, www.163.
com.

Siga estos pasos para configurar filtro DNS:

1.- Seleccione “activar” y haga clic en “Guardar” para que la función se inicie.
Esto es sólo el primer paso, usted debe seguir para crear reglas adecuadas
para “filtro DNS”.

2.- Filtro de entrada DNS palabras clave.

3.- Hay dos elementos suministrados, “Deja a través del repetidor para
las palabras clave DNS en la lista, otros se les niega” y “Denegar a través
del repetidor para las palabras clave DNS en la lista, otros se les permite”,
seleccione el elemento que desee, y haga clic en el botón “Guardar”.

4.- Si desea suprimir una entrada determinada de la lista, seleccione el


elemento apropiado en la lista, haga clic en “Eliminar” para eliminarla.

36
4.9 Static Routing (Enrutamiento estático)

La mayoría de los repetidores de banda ancha e inalámbricos utilizan el


modo NAT, por lo que esta característica está diseñada para los entornos
de red más comunes.
- Destination Network or IP Address (Red o dirección IP de destino): Especifique una
red de destino o dirección IP estática a la cual se enrute.

- Subnet Mask (Máscara de subred): la máscara de subred se utiliza para distinguir la


porción de red y la porción de host para una dirección IP.

- Next-hop IP Address (Dirección IP siguiente): Esta es una dirección IP del


dispositivo siguiente (y también es la puerta de acceso para el host local) que permite
la transmisión de datos entre el repetidor y la red o host remoto.

- Routing Table (Tabla de enrutamiento): Puede ver todos los elementos de la ruta
actual, haga clic en “delete” para eliminar un elemento de la ruta existente en la tabla
de enrutamiento.

4.10 QOS Settings (configuración de la QoS)


- Status (Estado): interruptor QoS.

- Automatic Uplink Speed (Velocidad de Uplink Automática): el repetidor se ajusta el


ancho de banda de enlace uplink de forma automática.

- Manual Uplink Speed (Velocidad Uplink Manual) (Kbps): podrá configurar el ancho de
banda de enlace uplink de forma manual.
37
- IP Address (Dirección IP): Establece el rango de direcciones IP para los hosts
restringidos.
- Minimum bandwidth (Ancho de banda mínimo): ajuste el ancho de banda del enlace
uplink y downlink.
- Maximum bandwidth (Ancho de banda máximo): ajuste el ancho de banda del enlace
uplink y downlink.

4.11 Dynamic DNS (DNS dinámico)


La función de DDNS le permite usar el nombre de dominio (no la dirección
IP) para acceder a Internet. Antes de poder utilizar esta función, es necesario
registrar una cuenta en el servicio DDNS en algún proveedor de servicios
DDNS, tales como “roay.cn”, “TZO.com”, “DynDNS”. Para más información,
puede visitar http://www.oray.net/Help.

- DDNS Status (Estado DDNS): estado actual de servidor DDNS.


- DDNS Server Provider (Proveedor de DDNS): Por ejemplo, si desea utilizar el
servicio de “roay.cn”, tiene que registrarse primero. Otros proveedores de servicios
DDNS funcionan de la misma manera.
- Username, Password, Dynamic Domain Name (Nombre de usuario, contraseña,
nombre de dominio dinámico): Después de registrar una cuenta de DDNS, obtendrá un
“Nombre de Usuario”, una “Contraseña” y un “nombre de dominio dinámico”, ingrese la
información en el campo correspondiente.

4.12 System Tools (Herramientas del sistema)


La configuración del sistema incluye la configuración de la contraseña,
configuración web, actualización, reinicio, restauración, WOL y hora del
sistema.

38
4.12.1. Firmware
Para actualizar, haga clic en “Examinar ...” y seleccione un archivo de
actualización, después de haber seleccionado el archivo correspondiente,
haga clic en “Actualizar”. No corte el suministro de energía durante el
proceso de actualización.

4.12.2 Time Settings (Configuración de hora)


Usted puede elegir el servidor de hora y la zona horaria del sistema.

4.12.3 Password (Contraseña)


El nombre de usuario / Contraseña por defecto es guest / guest. Para
garantizar la seguridad del repetidor, se recomienda que se cambie la
contraseña predeterminada por una de su elección, aquí podrá introducir
una nueva contraseña y luego volver a ingresarla para confirmarla. Haga clic
en el botón “Guardar” para guardar la configuración.

4.12.4 WOL
Ingrese la dirección MAC y haga clic en el botón de “Wake up” para activar
el host de destino en la LAN.

4.12.5 System Logs (Registros del sistema)


Aquí podrá examinar los registros del sistema. Puede configurar las
opciones mostradas en una página, el valor por defecto es 10.

4.12.6 Remote Management (Gestión Remota)


Estado de la administración WEB: por defecto está desactivado. Se puede
acceder al repetidor desde el sitio remoto utilizando “Configuración Web”.
Marque la casilla “Administración de puerto” e introduzca el número de
puerto y luego presione “Guardar” para habilitar la administración web.

39
4.12.7 Factory Defaults (valores predeterminados de fábrica)
Cuando haga clic en botón “Restaurar”, el repetidor borrará todos los ajustes
y los reemplazará con los valores de fábrica, asegúrese de que cuenta con
una copia de seguridad de la configuración actual antes de hacer clic en
este botón.

4.12.8 Reboot (Reiniciar)


Haga clic en “Reiniciar” para reiniciar el repetidor.

4.13 About

5.- SOLUCIÓN DE PROBLEMAS


1) No puedo acceder a la utilidad de configuración basada en Web desde
el equipo Ethernet utilizado para configurar el repetidor.

- Compruebe que el LED LAN está encendido. Si el LED no está encendido,


compruebe que el cable para la conexión inalámbrica a internet está bien
conectado.
- Compruebe si el ordenador se encuentra en la misma subred con la dirección
IP LAN del repetidor.
- Si el equipo actúa como cliente DHCP, compruebe si se le ha asignado una
dirección IP desde el servidor DHCP. Si no, tendrá que renovar la dirección IP.
- Utilice el comando ping para hacer ping a la dirección IP LAN del repetidor para
verificar la conexión.
40
- Asegúrese de que su navegador no está configurado para utilizar un servidor
proxy.
- Compruebe que la dirección IP que ha introducido es correcta. Si la dirección
de la IP LAN del repetidor ha cambiado, debe introducir la nueva dirección IP.

2) No recuerda contraseña (Reiniciar el repetidor sin registrarse).


- Use un lápiz para presionar el botón de reinicio durante 2-6 segundos cuando
el equipo está encendido, cuando libere el botón, el repetidor regresará a la
configuración de fábrica. La contraseña por defecto es guest.

3) Tengo problemas relacionados con la conexión del módem.


Por favor, siga los siguientes pasos para comprobar los problemas:

- Compruebe si el módem DSL funciona bien o la señal es estable. Normalmente


habrá algunas luces indicadoras del módem, los usuarios pueden comprobar si
la señal es buena o el módem funciona bien a partir de esas luces. Si no es así,
póngase en contacto con el ISP.
- Compruebe el panel frontal del repetidor, también hay algunas luces
indicadoras de allí. Cuando la conexión física es correcta, el indicador luminoso
de encendido y la luz de la CPU deben de estar encendidas y la luz WAN debe
parpadear. En su computadora, la luz correspondiente puerto LAN debe
parpadear. Si no es así, compruebe los cables.
- Repita los pasos en la configuración de WAN conectar con Internet a través
de módem DSL.

4) Puedo navegar por la utilidad de configuración, pero no puede acceder


a Internet.
- Compruebe si el LED WAN está encendido. Si no es así, verifique que la
conexión física entre el repetidor y el módem DSL / cable está bien conectada.

41
Asegúrese también de que el módem DSL / cable está funcionando
correctamente.
- Si LED WAN está encendido, abra la página Resumen del sistema de la utilidad
de configuración Web y compruebe el grupo de estado para ver si el puerto
WAN del repetidor ha obtenido con éxito una dirección IP.
- Asegúrese de que está utilizando el método de corrección (dirección IP
dinámica, PPPoE o IP estática) como lo requiere el ISP. Compruebe también
que ha introducido los ajustes correctos proporcionados por el ISP.
- Para los usuarios de cable, si su ISP requiere una tarjeta de registro de
direcciones MAC Ethernet, asegúrese de que ha clonado la dirección MAC del
adaptador de red del puerto WAN del repetidor. (Ver el campo de dirección MAC
en la configuración de WAN).

5) Mi cliente inalámbrico no puede comunicarse con otro equipo Ethernet.


- Asegúrese de que el adaptador inalámbrico funciona correctamente. Puede
abrir el Administrador de dispositivos en Windows para ver si el adaptador está
instalado correctamente.
- Asegúrese de que el cliente inalámbrico utiliza el mismo SSID y la
configuración de seguridad (si está activada) que el repetidor.
- Asegúrese de que los ajustes TCP / IP del adaptador inalámbrico están de
acuerdo a los requeridos por el administrador de red.
- Si está utilizando un adaptador inalámbrico 802.11b, y compruebe que el
elemento de modo 802.11g inalámbrico en la página de configuración básica,
está configurado para utilizar 802.11g.
- Utilice el comando ping para verificar que el cliente inalámbrico es capaz de
comunicarse con el puerto LAN del repetidor y con el equipo remoto. Si el cliente
inalámbrico puede hacer ping correctamente el puerto LAN del repetidor, pero
no para hacer ping al equipo remoto, compruebe la configuración TCP / IP del
equipo remoto.
42
6.- ESPECIFICACIONES
Alimentación: 9V- - - 500mA

Convertidor
Alimentación: 100-240V~ 50/60Hz 200mA
Salida: 9V- - - 500mA

ESPECIFICACIONES DEL SOFTWARE

Estándares IEEE802.11n/g/b, IEEE802.310Base-T, IEEE802.3u 100Base-TX

11n: 40Mbps (150 Mbps, 135 Mbps, 120 Mbps, 90 Mbps, 60 Mbps, 45 Mbps,
Promedio de señal 30 Mbps, 15 Mbps) 20Mbps (72 Mbps, 65 Mbps, 57 Mbps, 43 Mbps, 28 Mbps,
inalámbrica 21 Mbps, 14 Mbps, 7 Mbps) (Auto-Sense)
con respuesta
automática 801.11g: (54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 11Mbps,
9Mbps, 6Mbps)

802.11b: (11Mbps,9Mbps, 6Mbps, 5, 5Mbps, 2Mbps, 1Mbps)

Rango de frecuencia 2.4-2.4835GHz

Poder de transmisión 20dBm


inalámbrica (MAX)

vTecnología de DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM


modulación

130M: -68dBm@10% PER


108M: -68dBm@10% PER
Sensibilidad 54M: -68dBm@10% PER
del receptor 11M: -85dBm@8% PER
6M: -88dBm@10% PER
1M: -90dBm@8% PER

43
ESPECIFICACIONES DE HARDWARE

Interfase 4 puertos 10/100M LAN


1 puerto 10/100M WAN

Antena antena 5dBi

Temperatura de 0oC~40oC
operación

Humedad relativa 10 ~ 90%, No condensada

Humedad de 5%~95% No condensada


almacenamiento

Dimensiones 183 x 125,2 x 30,72mm

El diseño del producto y las especificaciones pueden cambiar sin


previo aviso.

44
Producto: Repetidor y punto de acceso inalámbrico de 150Mbps 802,11n P1114
Modelo: COM-817
Marca: Steren
PÓLIZA DE GARANTÍA
Esta póliza garantiza el producto por el término de un año en todas sus partes y mano de obra, contra
cualquier defecto de fabricación y funcionamiento, a partir de la fecha de entrega.

CONDICIONES
1.- Para hacer efectiva la garantía, presente esta póliza y el producto, en donde fue adquirido o en
Electrónica Steren S.A. de C.V.
2.- Electrónica Steren S.A de C.V. se compromete a reparar el producto en caso de estar defectuoso sin
ningún cargo al consumidor. Los gastos de transportación serán cubiertos por el proveedor.
3.- El tiempo de reparación en ningún caso será mayor a 30 días, contados a partir de la recepción del
producto en cualquiera de los sitios donde pueda hacerse efectiva la garantía.
4.- El lugar donde puede adquirir partes, componentes, consumibles y accesorios, así como hacer válida esta
garantía es en cualquiera de las direcciones mencionadas posteriormente.

ESTA PÓLIZA NO SE HARÁ EFECTIVA EN LOS SIGUIENTES CASOS:


1.- Cuando el producto ha sido utilizado en condiciones distintas a las normales.
2.- Cuando el producto no ha sido operado de acuerdo con el instructivo de uso.
3.- Cuando el producto ha sido alterado o reparado por personal no autorizado por Electrónica Steren S.A.
de C.V.
El consumidor podrá solicitar que se haga efectiva la garantía ante la propia casa comercial donde adquirió
el producto. Si la presente garantía se extraviara, el consumidor puede recurrir a su proveedor para que le
expida otra póliza, previa presentación de la nota de compra o factura respectiva.
DATOS DEL DISTRIBUIDOR
ELECTRÓNICA STEREN S.A. DE C.V.
Nombre del Distribuidor __________________________ Camarones 112, Obrero Popular, 02840, México, D.F.
Domicilio ______________________________________ RFC: EST850628-K51
Producto ______________________________________ STEREN PRODUCTO EMPACADO S.A. DE C.V.
Marca ________________________________________ Biólogo Maximino Martínez No. 3408 Int. 3 y 4, San
Modelo _______________________________________ Salvador Xochimanca, México, D.F. 02870,
Número de serie ________________________________ RFC: SPE941215H43
Fecha de entrega ________________________________ ELECTRÓNICA STEREN DEL CENTRO, S.A. DE C.V.
Rep. del Salvador 20 A y B, Centro, 06000, México. D.F.
En caso de que su producto presente alguna RFC: ESC9610259N4
falla, acuda al centro de distribución más ELECTRÓNICA STEREN DE GUADALAJARA, S.A.
cercano a su domicilio y en caso de tener alguna López Cotilla No. 51, Centro, 44100, Guadalajara, Jal.
duda o pregunta por favor llame a nuestro Centro RFC: ESG810511HT6
de Atención a Clientes, en donde con gusto le ELECTRÓNICA STEREN DE MONTERREY, S.A.
atenderemos en todo lo relacionado con su Colón 130 Pte., Centro, 64000, Monterrey, N.L. RFC:
producto Steren. ESM830202MF8
ELECTRÓNICA STEREN DE TIJUANA, S.A. de C.V.
Centro de Atención a Clientes Calle 2a, Juárez 7636, Centro, 22000, Tijuana, B.C.N.
01 800 500 9000 RFC: EST980909NU5
45
1
802.11n 150mbps Wi-Fi
REPEATER AND ACCESS POINT
COM-817

Thank you on purchasing your new Steren product.

This manual includes all the feature operations and troubleshooting necessary
to install and operate your new Steren´s 802.11n 150Mbps Wi-Fi repeater
and access point.

Please review this manual thoroughly to ensure proper


installation and operation of this product. For support, shopping,
and everything new at Steren, visit our website:

www.steren.com.mx

The instructions of this manual are for reference about the product. There may
be differences due to updates.

Please check our web site (www.steren.com.mx) to obtain the latest version of
the instruction manual.

2
INDEX

1.- HIGHLIGHTS 4

2.- HARDWARE INSTALLATION 5

3.- CONFIGURE YOUR COMPUTER 9

4.- REPEATER SETUP  16


4.1 Status  16
4.2 Quick Setup  18
4.3 WPS Settings  20
4.4 Network  22
4.5 Wireless  25

5.- TROUBLESHOOTING  40

6.- SPECIFICATIONS  43

3
1.- HIGHLIGHTS
The repeater and access point has LAN and WAN ports, allowing the creation of
a SOHO (with up to 150 Mbps transmission), complying with standard protocols,
it also includes a button to enable or disable the WPS function.

It can be used to share an Internet connection and also can be connected old
version devices (802.11b and 802.11g).

• Omni-directional antenna.

• 4x 10/100M Auto MDI/MDIX RJ45 ports.

• 1x 10/100M Auto MDI/MDIX RJ45 port.

• Wireless extended range transmission.

• PPPoE, L2TP, dynamic IP, static IP supported.

• Automatic connection, on demand.

• UPnP, WDS, static repeater, VON link supported.

• Virtual server, special applications and DMZ host supported (perfect for WEB
page host).

• SSID broadcast control and control access from MAC address lists supported.

4
• Built-in firewall with IP, MAC and URL filter function.

• DHCP server with automatic dynamic IP addresses assignation.

• 64/128 bit WEP, WPA, WPAZ supported.

2.- HARDWARE INSTALLATION


2.1. System Requirements
Minimum Requirements:

Broadband (DSL/Cable) modem and service with Ethernet port.


802.11n b/g/n wireless adapter or Ethernet adapter and cable for each
computer.

Internet Explorer® 5.0, Firefox® 2.0 or Safari® 1.4 or higher.

5
2.2. Indicators and Connections

LED Function
SYS Constantly on or off Abnormal
Flashing Normal
WAN ON WAN Connection normal
Flashing Data transmitting
OFF WAN Connection abnormal
LAN ON LAN Connection normal
Flashing Data transmitting
OFF LAN Connection abnormal

6
Rear panel

Description Function
PWR Power jack - don’t connect power adapters other than the one
supplied or your device may be damaged.
LAN Connect with computer NIC or Ethernet device.
WAN Connect with cable from modem.
RESET Restore factory default settings.

7
2.3. Hardware Installation Procedures
To set up the COM-817 Repeater please refer to the following picture:

1 2 3 4 WAN WLAN SYS POWER WPS

Attach one end of an Ethernet cable to your computer’s Ethernet port, and
the other end to one of the LAN ports of your repeater.

Connect another Ethernet cable from your Cable/DSL modem to the WAN
port of your repeater.

Connect the single DC output connector of the power adapter to the power
jack on the back of the repeater and plug the Power Adapter into an AC

8
2.4. Restore to Factory Default
If the repeater ever freezes in a setting change process or if you can’t access
it because you can’t remember the IP you have given it or other problem, you
may have to utilize the reset button on the back of the repeater to put it back
to factory settings. You have to press and hold this button for a few seconds
(2-6s) with a pencil when it is working, then release and it will restore settings
to the factory configuration.

The other way to restore factory settings is through the same user interface
used in setup. Click on ‘System management’- ‘Restore’, and click on the
‘Restore’ button.

3.- CONFIGURE YOUR COMPUTER


You can manage the COM-817 Repeater through the Web browser-based
configuration utility.

To configure the device via Web browser, at least one properly configured
computer must be connected to the device via Ethernet or wireless network.

The COM-817 Repeater is configured with the default IP address of 192.168.1.1


and subnet mask of 255.255.255.0 and its DHCP server is enabled by default.
Before setting up the repeater, make sure your computers are configured to ob-
tain an IP address automatically from the repeater by the steps below.

9
3.1 Configuration

3.1.3. Windows XP
1. Open My Computer on your desktop or through
the Start menu, right click on My Network Places
in the Other Places menu to the left and select
Properties. Right click on your Local Area
Connection in the window that appears and
select Properties.

2. In the properties window that appears, under


“This connection uses the following items:”
select Internet Protocol (TCP/IP) and then click
the Properties button below.

3. Choose Obtain an IP address automatically


and Obtain DNS server address automatically,
and then press OK to close the Internet Protocol
(TCP/IP) Properties window.

4. Press OK to close the Local Area Connection


Properties window.

10
3.1.4. Windows Vista

1. Go to Start → Control Panel.

2. Double click on Network and


Sharing Center.

3. Click on Manage Network


Connections.

4. Right click on the Local Area Connection


icon and select Properties.

5. Highlight Internet Protocol Version 4 (TCP/


IP) and then click on the Properties button.

6. Choose Obtain an IP address automatically and


Obtain DNS server address automatically, and
then press OK to close the Internet Protocol (TCP/
IP) Properties window.

11
7. Press OK to close the Local Area
Connection Properties window.

3.2. Checking Connection to Repeater


After configuring the TCP/IP protocol, use the ping command to verify if the
computer can communicate with the Repeater. To execute the ping com-
mand, open the DOS window and Ping the IP address of the 300Mbps Wire-
less-N Broadband Repeater at the DOS prompt:

For Windows 98/Me: Start → Run. Type command and click OK.

For Windows 2000/XP: Start → Run. Type cmd and click OK.

For Windows 7 Start → Accessories → Command Prompt

At the DOS prompt, type the following command: ping 192.168.1.1

12
The command window should return something similar to the following:

C:\Documents and Settings\admin>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time=1ms TTL=64


Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64

Ping statistics for 192.168.1.1:


Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 1ms, Average = 1ms

If the computer fails to connect to the repeater, the Command window will
return the following:
C:\Documents and Settings\admin>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out.


Request timed out.
Request timed out.
Request timed out.

Ping statistics for 192.168.1.1:


Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Verify your computer’s network settings are correct and check the cable
connection between the repeater and the computer.

13
3.3. Log In to Repeater Interface
Open a web browser (Safari, Internet Explorer, etc.) on the computer you
have just connected to the repeater, type http://192.168.1.1 in the address
bar, and press enter.

In the pop-up window, enter the user name guest


and password guest and then click OK.

After you have logged in, the repeater’s user interface will be
displayed. The left menu shows the main options to configure the system,
and the right screen is the summary information for viewing and adjusting
the configurations.
14
After you have logged in, the repeater’s user interface will be displayed. The
left menu shows the main options to configure the system, and the right screen is
the summary information for viewing and adjusting the configurations.

15
4.- REPEATER SETUP
4.1 Status
This feature provides running status
information and detailed information
about repeater.

4.1.1 Version
Show the hardware and firmware version.

4.1.2 WAN
This feature provides running status information of the WAN port (the
port that connects to the Internet).

- Connection Type: Display repeater’s current connection type. It should


be one of “PPPoE”, “DHCP”, “Static IP”, depending on what kind of
connection type your ISP provides.
- Physical Address: The physical address of WAN port, this is a
unique address assigned by manufacturer.
- IP Address: The IP address you obtained after connect to the Internet, if
you haven’t connected to the Internet yet, this field is 0.0.0.0.
- Subnet Mask: The Subnet mask you obtained after connect to the
Internet, if you haven’t connected to Internet yet, this field is 0.0.0.0.
- Default Gateway: The IP address of Default gateway you obtained after
connect to the Internet, if you haven’t connected to Internet yet, this field
is 0.0.0.0.
16
- Primary DNS: The DNS server translates domain or website names into IP
address, input the most common DNS server address you used or provided
by your ISP.
- Secondary DNS: Input IP address of a backup DNS server or you can leave
this field blank
- Link Status: Show the current status of link information. You can choose
connect or disconnect by manually.

4.1.3. LAN
This item provides information about repeater’s LAN port, display LAN port’s
physical address, IP address and current situation of DHCP server.

4.1.4. Wireless
This item provides current running information of wireless signal.

- Wireless status: Display wireless interface status is enabled or not


- Name (SSID): SSID (Service Set Identifier) is your wireless network’s name
shared among all points in a wireless network.
- Mode: Current wireless mode of wireless repeater
- Channel: Display current channel of your wireless repeater.
- MAC Address: The MAC address is used for wireless communication
- WPS Status: Display WPS (Wi-Fi Protected Setup) status is enabled or not.

4.1.5 Repeater Status


This item provides current System’s running information.

4.1.6 Traffic Statistics


This item provides statistics information about send and received bits by the
repeater.
17
4.2 Quick Setup
Providing you the convenient and simplest
method for configure the repeater, the purpo-
se of this item is to provide an easy way for
you to use it and configure your repeater to
access the Internet quickly; including ‘DHCP
(dynamic)’, ‘PPPoE’, ‘Static’ and ‘Wireless
Configuration’.
This is the most convenient tool for you to configure repeater.

4.2.1 DHCP (dynamic)


After select this item, you will obtain an IP address from your ISP
automatically, those ISP who supply Cable modem always use DHCP
technology.

4.2.2 PPPoE
If your ISP provides you the PPPoE service (most ISP with DSL
transaction will supply this service), please select this item. In the
“Convenient configuration” You can input your PPPoE username and
password to access the Internet.
- PPPoE Username: Input PPPoE username provided by ISP
- PPPoE Password: Input PPPoE password provided by ISP.

4.2.3 Static
This item should only be used when users use a static IP address to
access Internet, you should input your “WAN IP address”, ”subnet
mask”,” default gateway” and “DNS server (domain name server)”
according to the information provided by your ISP.
18
And every IP address should be input in appropriate IP field, a IP address
only divided into four IP octets by sign“.” is acceptable.
- WAN IP address: The IP address that your Internet access into.
- Subnet mask: Specify a Subnet Mask for your WAN segment.
- Default gateway: It is provided by your ISP.
- Primary DNS: DNS server is used for resolve domain name. Your ISP will
provides you with at least one DNS IP address, input IP address of your DNS
server in this field.
- Secondary DNS: Input IP address of backup DNS server, or you can leave
this field blank.

4.2.4 Wireless Configuration


You can choose “Enable” or “Disable” to enable or disable the
wireless function. The default setting is “enable”. If you chose the
“Disable” status, the repeater will become a wired broadband repeater
without wireless function, so be careful when you choose this status.

- SSID: SSID (Service Set Identifier) is your wireless network’s name shared
among all points in a wireless network. The SSID must be identical for all
devices in the wireless network. It is case-sensitive and must not exceed 32
characters. Make sure all points in the wireless network have the same SSID.
For added security, you should change the default SSID to a unique name.
- Region: Choose a correct region which fit your use environment.
- Channel: Wireless repeater communicates to wireless cards in a particular
channel, which can reduce interference between different channels.
- Authentication Type: Different authentication types use different encryption
types, which can encrypt wireless data to protect your wireless communication.
19
4.2.5 MAC Clone
The WAN port of repeater has a unique MAC address assigned by
manufacturer; it called as “Default MAC”. The “Clone MAC” is used
for some special situations; For example, ISP only allows certain MAC
address to access the Internet, thus you can modify your WAN port’s
MAC address in accord with the requirement of ISP, avoiding ISP’s
detection.

4.3 WPS Settings


Wi-Fi Protect Setup (WPS)
function can help you create a safe
network easily. You can through ‘PIN
Input Config (PIN)’ or ’Push Button
(PBC)’to encrypt your network.

This repeater also provides WPS button, you only need to push the WPS button
in this repeater and the wireless network card that support WPS function, then
the repeater will be encrypted to WPA2-AES mode automatically.

Note:
If you have configured encryption mode in your repeater, then when you use
this WPS function, please configure the authentication type to none, and then it
will be encrypted to WPA2-AES mode automatically. If you don’t want to change
your authentication type, then when you use this function, the repeater will be
encrypted to the mode that you have configured.

20
4.3.1 WPS Settings
- WPS Status: You can use this function to setup the wireless connection
between this repeater and wireless network card. The default is Enable.
- AP PIN Code: This code is to identify de wireless device.
- Add A New Device: Add a new device by WPS.

4.3.2 Add a New Device


- Enter the new device’s PIN: This code may be marked in the new wireless
device.
- Press the button of the new device in two minutes: New device will send
a PIN code to wireless repeater.
WPS can connect the wireless adapter and the repeater in a safe way. If
you have a wireless network card which has WPS button, you may set up
a safe network via the following methods.

Method 1:
1. Push the WPS button in the Repeater until the SYS LED is flashing
yellow.
2. Push the WPS button in the wireless network card for about 3-5seconds.
3. The safe connection will be established automatically.

Method 2:
1. Input the PIN code of the adapter’s WPS page into the repeater’s WPS
configure page, then click ’connect’.
2. Push the ‘PIN Input Config (PIN)’ in the Wi-Fi protect setup of the adapter
3. Select the repeater in the pop-up window, then click ‘Select’
4. The connection between the adapter and the repeater will be established
automatically.
21
Method 3:
1. Select ‘Input PIN from AP’ in WI-FI protect setup page, input PIN of the
repeater, and then click ‘PIN Input Config (PIN)’.
2. Select the repeater in the pop-up window, then click ‘Select’.
3. The connection between the adapter and the repeater will be established
automatically.

Note: If there is more than one AP in the PBC mode when you use the
method 1, there will be session overlap. Please using method 2/3 or wait
for a while push the button again.

4.3.3 WPS Configuration


Display the WPS configuration information.

4.4 Network

4.4.1 WAN
This item provides two access
types for you to configure the
WAN parameters.

They are wired access and


wireless access.

22
4.4.1.1. Wired Access
- Internet Access Type: Ask your ISP to get the correct access type.
- IP: The IP address you obtained after connect to the Internet, if you haven’t
connected to the Internet yet, this field is 0.0.0.0.
- Subnet Mask: The Subnet mask you obtained after connect to the Internet,
if you haven’t connected to Internet yet, this field is 0.0.0.0.
- Gateway: The IP address of Default gateway you obtained after connect
to the Internet, if you haven’t connected to Internet yet, this field is 0.0.0.0.
- MTU: The MTU (Maximum Transmission Unit) setting specifies the largest
packet size permitted for network transmission. Most DSL users should use
the value 1492.You can set MTU manually, and you should leave this value
in the 1200 to 1500 range. If the value you set is not in accord with the value
ISP provide, it may causes some problems, such as fail to send Email, or
fail to browse website. So if that happen, you can contact your ISP for more
information and correct your repeater’s MTU value.
- Primary DNS: The DNS server translates domain or website names into IP
address, input the most common DNS server address you used or provided
by your ISP.
- Secondary DNS: Input IP address of a backup DNS server or you can leave
this field blank.

4.4.1.2 Wireless Access


- SSID: SSID (Service Set Identifier) is your wireless network’s name shared
among all points in a wireless network. The SSID must be identical for all
devices in the wireless network. It is case-sensitive and must not exceed
32 characters. Make sure all points in the wireless network have the same
SSID. For added security, you should change the default SSID to a unique
name.
23
- Authentication Type: “None” means do not encrypt wireless data.
- Internet Access Type: Ask for your ISP to get the correct access type.
- IP: The IP address you obtained after connect to the Internet, if you
haven’t connected to the Internet yet, this field is 0.0.0.0.
- Subnet Mask: The Subnet mask you obtained after connect to the
Internet, if you haven’t connected to Internet yet, this field is 0.0.0.0.
- Gateway: The IP address of Default gateway you obtained after connect
to the Internet, if you haven’t connected to Internet yet, this field is 0.0.0.0.
- MTU: The MTU (Maximum Transmission Unit) setting specifies the largest
packet size permitted for network transmission. Most DSL users should use
the value 1492.You can set MTU manually, and you should leave this value
in the 1200 to 1500 range. If the value you set is not in accord with the value
ISP provide, it may causes some problems, such as fail to send Email, or
fail to browse website. So if that happen, you can contact your ISP for more
information and correct your repeater’s MTU value.
- Primary DNS: The DNS server translates domain or website names into
IP address, input the most common DNS server address you used or
provided by your ISP.
- Secondary DNS: Input IP address of a backup DNS server or you can
leave this field blank.

4.4.2 LAN
The IP address of LAN port is used for access repeater itself by computers
that connect to the repeater directly; here you can set IP address you need.

The IP address format is like ***.***.***.***, and default IP address is


192.168.1.1, the default subnet mask is 255.255.255.0.

24
4.4.3 MAC Clone
The WAN port of repeater has a unique MAC address assigned by
manufacturer; it called as “Default MAC”. The “Clone MAC” is used for some
special situations; For example, ISP only allows certain MAC address to
access the Internet, thus you can modify your WAN port’s MAC address in
accord with the requirement of ISP, avoiding ISP’s detection.

4.4.4 Port Settings


Here you can set the repeater’s WAN and LAN interfaces work at 100M
duplex,100M half-duplex,10M duplex and 10M half-duplex communication
mode.

4.4.5 IGMP Proxy


Here you can set the IGMP Proxy ‘Enabled’ and ‘Disabled’.

4.5 Wireless

4.5.1. Wireless Settings


This section provides basic configuration
items for wireless repeater users, including
“wireless network status”, “SSID”, “Radio
Band”, “Radio Mode”, “MAC”, “SSID
broadcasting”, “Channel width”, “Channel
sideband”, “Region” and “Channel” several
basic configuration items.

25
- Wireless network status: You can choose “enable” or “disable” to enable
or disable the “Wireless Network Status”. If you choose “Disable”, the AP
function of wireless repeater will be turned off.
- SSID: The default is trst1.
- Radio band: You can select the wireless standards running on your
network, if you have Wireless-N and Wireless-B/G devices in your network,
keep the default setting, 802.11b+g+n
- Radio mode: You can select radio mode of wireless repeater, it contains
Access Point, Client, AP+WDS and WDS. The default setting is AP mode.
- MAC: Wireless repeater’s physical address.
- SSID Broadcasting: You can select “enable” or “disable” to enable or
disable the broadcast SSID function, If the setting of this field is disable,
wireless client can’t obtain this SSID to login in, then user have to input the
SSID value manually.
- Channel width: This switch allows you to set Repeater’s wireless bandwidth.
20MHz: In this mode you can get low bandwidth, little interference and slow
rate. 40MHz: In this mode you can get high bandwidth, high interference
and rapid rate. Use only when you have a pure repeater, draft 802.11n
wireless network.
- Channel sideband: It controls your wireless repeater to use higher or
lower channel when working on 40MHz.
- Region: please select the region where you live in.
- Channel: In 20MHz, you can select one channel from 1 to 13 manually,
and in 40MHz, you can select one channel from 1 to 9 or 5 to 13, which
provides a choice of avoiding interference.

26
4.5.2 Wireless Security
The item allows you to encrypt your wireless communication, and you
can also protect your wireless network from unauthorized user access. It
supplies “None”, “WEP”, “WPA-PSK”, “WPA2-PSK” and “WPA/WPA2-PSK”
five different encryption modes.

4.5.2.1 None
“None” means do not encrypt wireless data.

4.5.2.2 WEP
- Key Length: There are two basic levels of WEP encryption, 64 bits and 128
bits, the more bits password have, the better security wireless network is, at
the same time the speed of wireless is slower.
- Key Mode: If you select WEP to encrypt your data, choose the bits of
password, it should be 64 bits or 128 bits. Then choose the password
format; it should be HEX or ASCII. The valid character for HEX format should
be numbers from 0 to 9 and letters from A to F. HEX support mixed letters
and numbers. And ASCII supports all keyboard characters.
- Key Length description: When you select 64bits, you need to input 10 chars
for HEX and 5 chars for ASCII, and when you select 128bits, you need to
input 26 chars for HEX and 13 chars for ASCII.

Note: When the WPS is enabled, do not use WEP.

4.5.2.3 WPA-PSK
- Encryption type: You can select the algorithm you want to use, TKIP,
AES or TKIP&AES. TKIP means “Temporal Key Integrity Protocol”, which
incorporates Message Integrity Code (MIC) to provide protection against
hackers. AES, means “Advanced Encryption System”, which utilizes a
symmetric 128-Bit block data.

27
- Key Renewal: you can configure the renewal time between 60 to 86400
seconds.
- Key Length description: you need to input 8 to 63 ASCII characters no
matter which type you select.

4.5.2.4 WPA2-PSK
The WPA2-PSK is similar to WPA-PSK and with stronger encryption method
than WPA-PSK, using WPA2-PSK; you should input password (leave this
value in the range of 8 to 63 characters) and key renewal time (leave this
value in the range of 60 to 86400 seconds).

4.5.2.5 WPA/WPA2-PSK
This mode mixes WPA-PSK and WPA2-PSK modes, which provides higher
security level; you can configure it according with WPA-PSK or WPA2-PSK.

4.5.3 Wireless MAC Filtering


- MAC Filter Status: the default is disable. You can filter wired users by
enabling this function; thus unauthorized users cannot access the network.
- Description: describe MAC Filter list to tell from different MAC Filter lists.
- Rule: you can select permit or deny. The default is permit.
- MAC address: input the MAC address that you want to control. The default
format is **-**-**-**-**-** (e.g.: 00-22-33-da-cc-bb).

5.5.4 WDS

4.5.4.1 WDS Settings


If you have selected WDS or AP+WDS mode in Wireless Basic-Radio Mode,
follow the following configurations.
28
- WDS Name: Give a description of your wireless bridge.
- WDS MAC Address: If the current working mode is “WDS” or “AP+WDS”,
then you need to configure wireless bridge configuration. Enter MAC address
of remote access point, at the same time the remote access point also need
to configure to “WDS” or ”AP+WDS” mode.
- Current WDS Information: It illustrates basic information of all wireless
bridge that in connection status, you may delete unnecessary bridge.
AP1:
- Select radio mode is WDS or AP+WDS in wireless management-basic of
AP1.
- Click on ‘Wireless Management’- ‘AP Setup’- ‘Security’ and select and save
None as authentication type.
- Click on ‘Wireless Management’- ‘AP Setup’- ‘Security’ and select and save
None as WDS authentication type or select a WDS security type, enter key
and save.
- Input WDS name (e.g.: default), input MAC address of AP2 (00-22-4f-bc-
af-5d), click add, then the record named default will appears in WDS list.
- Select channel is ‘Channel 6’ in wireless management-basic of AP2.

AP2:
- Selected radio mode must be WDS or AP+WDS in wireless
management-basic of AP2.
- The AP2IP address should be 192.168.1.x (1<x<255,e.g.: x=8).
- Select ‘LAN setup’-‘DHCP server’, select disable DHCP server.
- Input WDS name (e.g.: Default), input MAC address of AP1 (00-22-4f-cc-
ae-f5), click add, then the Default name will appear in WDS list.
- Select ‘Channel 6’in basic wireless management of AP2.

Note: Before you setup WDS connection, please make sure that AP1 and
AP2 is in the same network, that is if the IP address of AP1 is 192.168.1.1,
then the IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8).
29
4.5.4.2 Repeater Settings
Wireless Repeater mode is used to send the wireless signal from a net point
to the next and amplify it and form a new wireless coverage area.

AP1:
- Select radio mode is ‘Access Point’ in wireless management-basic of AP1.
- Select Channel is ‘Channel 6’ in wireless management-basic of AP1.

AP2:
- Select REPEATER’radio mode ‘in wireless management-basic of AP2.
- Select Repeater SSID is ‘Netis1’ in wireless management-basic of AP2.
- Select Channel is ‘Channel 6’in wireless management-basic of AP2.
- The IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8).
- Select ‘LAN setup’-‘DHCP server’, select disable DHCP server.

AP3:
- Select radio mode is ‘REPEATER’ in wireless management-basic of AP3.
- Repeater SSID is ‘Netis2’in wireless management-basic of AP2.
- Select Channel is ‘Channel 6’ in wireless management-basic of AP2.
- The IP address of AP3 should be 192.168.1.x (1<x<255),but different from
AP2.
- Select ‘LAN setup’-‘DHCP server’, select disable DHCP server.

4.5.5. Wireless Advanced


These settings are only for more technically advanced users who have a
sufficient knowledge about wireless LAN. These settings should not be
changed unless you know what effect the change will have on your AP.
30
- Authentications type: The default is set to “Auto”, which allows “Open
System” or “Shared Key” authentication to be used. Select “Shared Key” if
you only want to use “Shared Key” authentication (the sender and recipient
use a WEP key for authentication).
- Beacon Interval: The interval time of this COM-817 Repeater broadcast a
beacon. Beacon is used to synchronize the wireless network. The valid
interval is 20-1000, the default is 100.
- RTS Threshold: You can set RTS Threshold value in this field, the valid
range should be 256-2347 and default value is 2347. If a network packet is
smaller than the preset RTS threshold size, the RTS/CTS mechanism will
not be enabled.
- Aggregation: You can accelerate the wireless transmission speed by
enabling the aggregation function. The default is AMPDU+AMSDU.
- Fragmentation Threshold: It specifies the maximum size of packet during
the fragmentation of data to be transmitted.
- Transmission Rate: Transmit rate indicates the transmission speed of
wireless LAN access. The default setting is “Auto” and you can set this value
between 1-54Mbps range.
- ShortGi: You can select “Enable” or “disable”.
- Protection: Using 802.11b and 802.11g mixed mode may result in poor
network performance. By enabling 802.11 protection, it will ameliorate
performance of 802.11g devices in your wireless network.
- Preamble Type: “Short Preamble” is suitable for heavy traffic wireless
network. “Long Preamble” provides much communication reliability; the
default setting is “Long Preamble”.

31
4.5.6. Wireless Statistics
Display current status of the wireless client associated with AP.

4.5.7. Multiple AP Settings


The default status of secondary AP is disable, you can select enable to
enable the secondary AP. Please refer to Quick Setup Wireless Security and
Wireless Statistics for details.

4.6. DHCP
4.6.1 DHCP Settings

4.6.2 DHCP Clients List


Display the state of assigned IP by DHCP Server.

4.6.3 Address Reservation


Address Reservation: reserve IP address for designed physical address
host. If you want to configure a fixed IP address for some host, please input
physical address and IP address, then click add.

4.7. Forwarding

4.7.1 Virtual Servers


- Description: Describe current virtual server item.
- Internal Host IP Address: The “Internal Host IP Address” indicates IP
address of the internal host using virtual server.
- Protocol: The protocol item supplies several protocols. For example, if you
have web server within LAN, you can select the HTTP template then the
repeater will input port number 80 automatically.
- External Port: Input an extranet port number (the users in Internet can see
these ports).
32
- Internal Port: Input an intranet port number.

4.7.2 Port Triggering

Port trigger module dynamically registers virtual server rules when any IP
host generates the packet from the specified trigger protocol and port. Port
trigger module use forward protocol type and port number and use the IP
address of host that generates the trigger packet when it registers a rule.

- Predefined Trigger Rules: select one of the Predefined Rules.


- Rule Name: describe the Predefined Trigger that you will configure.
- Trigger Protocol: you can select TCP/UDP.
- Trigger Port: you can select a part of ports.
- Forward Protocol: you can select TCP/UDP.
- Forward Port: you can select a part of ports.

4.7.3 DMZ
DMZ opens all the ports of one computer, exposing the computer to the
Internet. So it should only be used for some special-purpose. Using this
function you can select “DMZ” item and input IP address of DMZ host, then
click “Save”. For security purposes, we suggested that using “Virtual
servicer” instead of “DMZ”.

4.7.4 UPnP
The UPnP function supports load Application’s port forward record
automatically. Select “Enable” to enable this function.

4.7.5 FTP Private Port


Some games, servers, and applications are no longer effect when behind
the NAT repeater, so this item provides function of port mapping from LAN

33
to WAN.
4.8. Security

4.8.1. Security Settings


VPN is commonly used for encapsulate and encrypt data across the public
network. For VPN tunnel, the repeater supports IPSEC pass-through, PPTP

4.8.2 IP Address Filtering

- Status: the default is disable. The rules of “Internet access control” based
on source IP, port number and protocol.
- Description: describe IP Firewall list to tell from different IP Firewall lists.
- Rule: you can select permit or deny. The default is permit.
- Source IP address: input the source IP address that you want to control.
The default format is ***.***.***.***(e.g: 192.168.2.3).
- Protocol and Port: If the rule has already existed in “Protocol Template”.

You can select appropriate item and apply it. Or you can input protocol type
and port number manually, click “add” button, then the item will displayed in
the list.

Follow the following steps to set Internet Access Control:

1. You can select “enable” and click “Save” to enable “IP Firewall” function.
This is only the first step; you should continue to create appropriate rules for
“IP Firewall”.
2. Input description information for current access control rule in the
“Description” field. Input IP address of host you want to restrict.
34
3. There are two items supplied, “Permit through the repeater for IP address
listed, others are denied” and “Deny through the repeater for IP address lis-
ted, others are permitted”, Select the item you want, and click “Save” button.

4. If you want to delete certain item on the list, select appropriate item on the
list, click “delete” to delete it.

4.8.3 MAC Filtering

- Status: the default is disable. You can filter wired users by enabling this
function; thus unauthorized users cannot access the network.
- Description: describe MAC Filter list to tell from different MAC Filter lists you
can select permit or deny. The default is permit
- MAC address: input the MAC address that you want to control. The default
format is **-**-**-**-**-** e.g.: 00-22-33-da-cc-bb

Follow the following steps to set MAC filter:

1. Enable MAC Filter, then select save.


2. Add MAC address you want to control in the “MAC address” field (the
format is **-**-**-**-**-**), then click “Add” button, and you will see the MAC
address has displayed in the MAC list.
3. There are two items supplied, “Permit wireless connection for MAC
address listed (others are Denied)” and “Deny wireless connection for MAC
address listed (others are Permitted)”, Select the item you want, and click
“Save” button.

35
4.8.4 Domain Filtering

- Status: the default is disable. “DNS filter” is able to filter certain domain
name such as www.sina.com.

- Rule: you can select permit or deny. The default is permit.

- DNS Filter Key words: Input website name or Domain name in the “DNS
Key Words” field, such as www.163.com.

Follow these steps to set DNS filter:

1. You can select “enable” and click “Save” to enable “DNS Filter” function.
This is only the first step, you should continue to create appropriate rules for
“DNS Filter”.

2. Input DNS Filter Key words.

3. There are two items supplied, “Permit through the repeater for DNS Key
words listed, others are denied” and “Deny through the repeater for DNS
Key words listed, others are permitted”, Select the item you want, and click
“Save” button.

4. If you want to delete certain item on the list, select appropriate item on the
list, click “delete” to delete it.

36
4.9 Static Routing

Most of broadband and wireless repeaters use NAT mode, so this feature is
designed for most common network environment.

- Destination Network or IP Address: Specify a certain destination Network or


IP address which static route forward to.

- Subnet Mask: Subnet mask is used for distinguish Network portion and
Host portion for an IP address.

- Next-hop IP Address: This is an IP address of the next-hop device (and also


is the gateway address for local host) that allows forwarding data between
repeater and remote network or host.

- Routing Table: You can check out all current route items, click “delete”
button to delete a route item existed in routing table.

37
4.10 QOS Settings
- Status: QOS switch.
- Automatic Uplink Speed: Repeater adjusts uplink bandwidth automatically.
- Manual Uplink Speed (Kbps): User configures uplink bandwidth manually.
- IP Address: Set the IP address range for restricted hosts.
- Minimum bandwidth: setup uplink and downlink bandwidth.
- Maximum bandwidth: setup uplink and downlink bandwidth.

4.11 Dynamic DNS


The DDNS feature allows you using domain name (not IP address) to access
Internet. Before you can use this feature, you need to register an account
for DDNS service at DDNS service providers, such as “roay.cn”, ”TZO.com”,
”DynDNS”. For more information, you can visit http://www.oray.net/Help.

- DDNS Status: Current status of DDNS server.


- DDNS Server Provider: For example, if you want to use service of “roay.
cn”, you have to first register an account. Other DDNS service providers as
the same.
- Username, Password, Dynamic Domain Name: After register an DDNS
account from DDNS service providers, you will get “User Name”, “Password”,
”Dynamic Domain Name”, Input information in appropriate field.

4.12 System Tools


System management includes password setup, web Setup, upgrade, reboot,
restore, WOL and System time.

38
4.12.1. Firmware
Click “Browse...”button and select a File to upgrade, after you have selected
the appropriate file, click “Upgrade” button to execute upgrade procedure.
Do not cut off the power supply during the process of upgrading.

4.12.2 Time Settings


You can choose the time server and the time zone for the system time.

4.12.3 Password
The default username/password is guest/guest. To ensure the Repeater’s
security, it is suggested that you change the default password to one of your
choice, here enter a new password and then Re-enter it again to confirm your
new password. Click “Save” button to save settings.

4.12.4 WOL
Input host MAC address, and then click button of “Wake up” to wake up the
target host in the LAN.

4.12.5 System Logs


Examine system logs. You can configure items shown in one Page, the
default is 10.

4.12.6 Remote Management


WEB Management Status: the default is disable. Repeater can be accessed
on the remote site using “Web setup”. Check the “Management Port” and
enter the port number and then press “save” button to enable web mana-
gement.

4.12.7 Factory Defaults


Click “Restore” button, the Repeater will erase all of your settings and re-
place them with the factory defaults, make sure you have backup current
39
4.12.8 Reboot
Click “Reboot” button to restart the repeater.

4.13 About

5.- TROUBLESHOOTING
1) I cannot access the Web-based Configuration Utility from the Ethernet
computer used to configure the repeater.

- Check that the LAN LED is on. If the LED is not on, verify that the cable for the
LAN connection is firmly connected.
- Check whether the computer resides on the same subnet with the repeater’s
LAN IP address.
- If the computer acts as a DHCP client, check whether the computer has been
assigned an IP address from the DHCP server. If not, you will need to renew the
IP address.
- Use the ping command to ping the repeater’s LAN IP address to verify the
connection.
40
- Make sure your browser is not configured to use a proxy server.
- Check that the IP address you entered is correct. If the repeater’s LAN IP ad-
dress has been changed, you should enter the reassigned IP address instead.

2) I forget Password (Reset the Repeater without Login).


- Use a pencil to press the button for about 2-6 seconds when it is working, then
leave your hands, it will restore settings to the factory configuration. The default
password is guest.

3) I have some problems related to Connection with Cable Modem.


Please follow the following steps to check the problems:

- Check whether the DSL modem works well or the signal is stable. Normally
there will be some indicator lights on the modem, users can check whether the
signal is ok or the modem works well from those lights. If not, please contact the
ISP.
- Check the front panel of the Repeater, there are also some indicator lights
there. When the physical connection is correct, the Power light and the CPU light
should be solid; the WAN light should be blinking. If you use your computer, the
corresponding LAN port light should be blinking too. If not, please check whether
the cables work or not.
- Repeat the steps in WAN Setup Connect with Internet through DSL Modem.

4) I can browse the repeater’s Web-based Configuration Utility but cannot


access the Internet.
- Check if the WAN LED is ON. If not, verify that the physical connection between
the repeater and the DSL/Cable modem is firmly connected. Also ensure the
DSL/Cable modem is working properly.
41
- If WAN LED is ON, open the System Overview page of the Web configuration
utility and check the status group to see if the repeater’ s WAN port has suc-
cessfully obtained an IP address.
- Use th- Make sure you are using the correction method (Dynamic IP Address,
PPPoE, or Static IP) as required by the ISP. Also ensure you have entered the
correct settings provided by the ISP.
- For cable users, if your ISP requires a registered Ethernet card MAC address,
make sure you have cloned the network adapter’ s MAC address to the WAN port
of the repeater. (See the MAC Address field in WAN Setup.)

5) My wireless client cannot communicate with another Ethernet computer.


- Ensure the wireless adapter functions properly. You may open the Device
Manager in Windows to see if the adapter is properly installed.
- Make sure the wireless client uses the same SSID and security settings (if
enabled) as the COM-817 Repeater.
- Ensure that the wireless adapter’s TCP/IP settings are correct as required by
your network administrator.
- If you are using a 802.11b wireless adapter, and check that the 802.11G
Mode item in Wireless Basic Setting page, is not configured to use 802.11G
Performance.
- Use the ping command to verify that the wireless client is able to communicate
with the repeater’s LAN port and with the remote computer. If the wireless client
can successfully ping the repeater’ s LAN port but fails to ping the remote com-
puter, then verify the TCP/IP settings of the remote computer.

42
6.- SPECIFICATIONS
Input: 9V- - - 500mA

Power converter
Input: 100-240V~ 50/60Hz 200mA
Output: 9V- - - 500mA

SOFTWARE SPECIFICATIONS

Standards IEEE802.11n/g/b, IEEE802.310Base-T, IEEE802.3u 100Base-TX

Wireless signal 11n: 40Mbps (150 Mbps, 135 Mbps, 120 Mbps, 90 Mbps, 60 Mbps, 45 Mbps,
rate with automatic 30 Mbps, 15 Mbps) 20Mbps (72 Mbps, 65 Mbps, 57 Mbps, 43 Mbps, 28 Mbps,
answer 21 Mbps, 14 Mbps, 7 Mbps) (Auto-Sense)

801.11g: (54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 11Mbps,


9Mbps, 6Mbps)

802.11b: (11Mbps,9Mbps, 6Mbps, 5, 5Mbps, 2Mbps, 1Mbps)

Frequency range 2.4-2.4835GHz

Wireless power 20dBm


transmission

vModulation DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM


technology

130M: -68dBm@10% PER


108M: -68dBm@10% PER
Receiver sensitivity 54M: -68dBm@10% PER
11M: -85dBm@8% PER
6M: -88dBm@10% PER
1M: -90dBm@8% PER

43
HARDWARE SPECIFICATIONS

Interface 4 10/100M LAN Ports


1 10/100M WAN Port

Antenna 5dBi antenna

Operating 0oC~40oC
temperature

RH 10 ~ 90%, non condensing

Storing humidity 5%~95% non condensing

Dimensions 183 x 125.2 x 30.72mm

Product design and specifications are subject to change without previous notice.

44
Product: 802.11n 150Mbps Wi-Fi repeater and access point
Part number: COM-817
Brand: Steren
WARRANTY

This Steren product is warranted under normal usage against defects in workmanship
and materials to the original purchaser for one year from the date of purchase.

CONDITIONS

1. This warranty card with all the required information, invoice, product box or
package, and product, must be presented when warranty service is required.
2. If the product is in the warranty time, the company will repair it free of charge.
3. The repairing time will not exceed 30 natural days, from the day the claim was
received.
4. Steren sell parts, components, consumables and accessories to customer, as well
as warranty service, at any of the addresses mentioned later.

THIS WARRANTY IS VOID IN THE NEXT CASES:

If the product has been damaged by an accident, acts of God, mishandling, leaky
batteries, failure to follow enclosed instructions, improper repair by unauthorized
personnel, improper safe keeping, among others.

a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase
ticket.

RETAILER INFORMATION
Name of the retailer In case your product fails
Address or have questions, please
Product contact your nearest dealer.
Brand If you are in Mexico, please
Part number call to our Call Center.
Serial number 01 800 500 9000
Date of delivery
45

También podría gustarte