Documentos de Académico
Documentos de Profesional
Documentos de Cultura
74109
New Generation Single Component Polyurethane based elastomeric adhesive sealant |
High strength bonding and sealing
Bulletin Technique
Product Description
AlphaSeal PU25VLS NG is new generation single component polyurethane based
elastomeric adhesive sealant which cures under the effect of atmospheric humidity to form
a high elasticity joint that has a good resistance to tear and to weather.
Areas of Applications
AlphaSeal PU25VLS NG can be used for bonding various construction materials and as
sealing joint. specially adapted for bonding various building and for expansion joints,
panel joints in Precast Construction. This sealant adheres without primer on substrates
commonly used, like wood, anodized aluminum, polyester, glass, concrete, baked clay,
stone, ceramic tiles. For difficult materials, including plastics such as PVC, ABS, PMMA, or
materials such as raw aluminum or lacquered metal, perform preliminary tests to
determine whether a surface preparation is necessary
Characteristics / Advantages
▪ One-component, ready to use
▪ Good adhesion to many substrates
▪ Low modulus
▪ ±50% joint movement
▪ Excellent workability, easy to smooth
▪ Can be overpainted / sanded
▪ Excellent durability
▪ Non-staining
▪ Made in France
Technical Data
Appearance Pasty
Color Various
Density at 20°C Black : 1.15 ± 0.02 - Others : 1.16 ± 0.02
Sagging (ISO 7390) < 3 mm
Application temperature 5 to 35°C
Skin formation time at 23 °C and 50%
5 to 10 h
HR
Cure time at 23 °C and 50 % HR 2 mm/ 24 h
Shore A hardness (internal method) 20
Approx 25
after ISO 868 - 3 seconds)
Version 2018/1, Page 1/3
CONSUMPTION
300 ml cartridge
Tube (mm) 2 3 4 5 6 7 8 9 10
Length of cord (m) 95 42 24 15 10,5 7,5 5,5 4,5 3,5
600 ml sausage
Tube (mm) 2 3 4 5 6 7 8 9 10
Length of cord (m) 190 85 47 30 21 15 11 9 7
PACKAGING
300 ml cartridges and 600 ml sausages Contact us for other packaging options.
SAFETY
Read the material safety data sheet before use.
Apply a primer if necessary. Check the compatibility of the solvent used with the
substrates. When using solvents, extinguish all sources of ignition and carefully follow
the safety and handling instructions given by the manufacturer or supplier. If
necessary, rub down metal surfaces beforehand. After rubbing down, the surface
should be recleaned. Allow the substrate to dry after degreasing.
We recommend to clean concrete with a metal brush.
Caulking :
AlphaSeal PU25 VLS NG can be applied by a manual or pneumatic gun. After
application, use a putty knife to smooth the joint with soapy water. This product should
be used within 24 hours of opening the cartridge or sausage ; otherwise, the sealant
could harden inside. Do not apply at a temperature under 5 °C. In cold weather, store
the cartridges at about 20 °C before use.
Avoid any contact with non-cured MS, hybrid PU or silicone sealants as well as with
alcohols or ammonia during curing.
Cleaning :
Tools should be cleaned with MEK or acetone before the sealant has completely
cured. After curing, abrasion is necessary.
Value Base All technical data stated in this Data Sheet are based on
laboratory tests. Actual measured data may vary due to
circumstances beyond our control.
Health & Safety For information and advice on the safe handling, storage and
disposal of chemical products, users should refer to the most
recent Material Safety Data Sheet containing physical,
ecological, toxicological and other safety-related data.
the product must test the product’s suitability for the intended
application and purpose. ROne International reserves the right to
change the properties of its products.
ROne International, Ocean Plaza, 503, Sector 18, Noida – 201301 (Uttar Pradesh), India,
Contact us @ Phone +91 120 4316626, Email: info.roneinternational@gmail.com