Documentos de Académico
Documentos de Profesional
Documentos de Cultura
No
Yes Yes
Chó ý:
1/. Th¸o J79 trªn ANALOG-LF30, J73 trªn SYSTEM-LF30, kiÓm tra ®iÖn ¸p ra trªn
PS1 cña VT60-3FF.
2/. KiÓm tra d©y dÉn, cã thÓ bÞ ch¹m vá ë b¶n lÒ xoay m¶ng System.
When the error F2 has occurred
Abnormal
Checked
MG-RS Replace MG-RS
Normal
VC+ abnormal
Chó ý:
- Check VC+; VC- (ANALOG-LF30, page 23/27)
- Check VP1, VP2: 2.8V/ t−¬ng ®−¬ng 280VDC trªn VC+, VC- vµ VC0
VP: 5.6V/ t−¬ng ®−¬ng 560VDC trªn VC+ vµ VC-
Adjust VP1 by VR15; VP2 by VR16 (ANALOG-LF30, page 9/27)
- Check power supply: 380V; AIN-1,2 on T1 transformer
When the error F3 has occurred
Abnormal
Reset Replace NEXSC
NEXSC
Normal
Abnormal
System LF-30 Replace System
Checked RmA, LF-30
RkV
Normal
Replace Analog
Analog LF-30 Abnormal LF-30(Check
Checked PKV,
IGBT gate wave
TKV, RMA, TMA,
form)
IFV
Normal
If phenomenon
Replace HT changed Replace HT cable
cable Is defective
Then checked
If phenomenon
not changed
changed
If phenomenon
not changed
changed
If phenomenon
changed
Replace X-ray Replace X-ray
Tube Tube Is
Then checked defective
If phenomenon
not changed
changed
Replace HT
Transformer
Chó ý:
1/.SYSTEM-LF30
Gi¸ trÞ chuyÓn ®æi tõ Digital -> Analog
- RkV (CP9): §Æt kV chôp 100kV: 5.00V VR11
- RmA (CP10): §Æt mA chôp 200mA: 1V VR10
- FVR (CP11): 5V/5A
- FkV (CP8): §Æt kV chôp 80kV: 4.00V
- FVF (CP4): §Æt dßng chiÕu 3.15A: 3.15V
- LMT (CP5): 5V/5A
2/. ANALOG-LF30
- IFL: CP38 dßng ®èt tãc lín: sau khi bËt m¸y 2A
- IFV CP44 : dßng ®èt tãc chung, khi Ready t−¬ng ®−¬ng gi¸ trÞ FVR
- Check Waveform CL,CO (Page 33 – Service manual)
3/. Cable, X-ray tube
When the error F4 has occurred
Abnormal
Reset Replace
NEXSC NEXSC
Normal
Normal
Replace
Analog LF-30
1/. ANALOG-LF30
Gi¸ trÞ chuyÓn ®æi tõ Digital -> Analog
- G¹t SW3-8, chän mode PKV (Page 3-70, Installation manual)
- PkV (CP6): §Æt kV chôp 150kV: 7.50V (Page 3/27 Circuit)
NÕu > 7.85V xuÊt hiÖn F4
F5 ( TKV Under):
- Khi GÆp lçi F5 cã ta kiÓm tra theo c¸c b−íc:
Cã
KiÓm tra cÇu ch× 600
FH 100 ( t¹i khèi
Inverter xem cã bÞ ®øt
IGBT bÞ háng
(1)
Khi thay IGBT chó y *
kh«ng
Cã
KiÓm tra Tô cã n¹p
b×nh th−êng kh«ng?
kh«ng
kh«ng
KiÓm tra r¬ le MG RS cã
lµm viÖc kh«ng, c¸c §iÖn
trë gi¶m xung ®· §c ng¾n
KiÓm tra tÝn
hiÖu J203
(2)
m¹ch ch−a?
Cã
kh«ng
R¬ le MG D ®· lµm viÖc
ch−a?§iÖn trë x¶ tô KiÓm tra tÝn
RC+/RC- cã bt kh«ng? hiÖu J201 (3)
Cã
kh«ng
KiÓm tra d¹ng sãng më cho
IGBT: CP16(AD), CP17 (BC)
Installation manual Analog LF 30 háng
trªn Analog LF 30 page 4-20
(4)
KiÓm tra d¹ng sãng cña Gate Thay khèi IGBT vµ
Driver 96 ( Theo c¸c b−íc trong
installation manual page 4-25) Gate driver
B×nh th−êng
bÊt th−êng
G¹t S2-5, S3-8 (Nexsc), do CP23
trªn Analog LF 30 (5V/5A) Háng SYSTEM LF 30 PCB
B×nh th−êng
bÊt th−êng
B×nh th−êng
BÊt th−êng
B×nh th−êng
bÊt th−êng
KiÓm tra d¹ng sãng KV=/ K.Tra LD1 trªn m¶ng
KV – ( Installation manual Analog LF 30 sang?
PhÇn 4.14.3 (page 4-28)
Kh«ng
Cã
BÊt th−êng KiÓm tra SystemLF 30
PCB,Nexsc PCB
F6 (Stater break).
- Khi mÊt nguån cho phÇn khëi ®éng (cÇu ch× F50, F 125 trªn T1 bÞ ®øt, connector
JS2 bÞ láng)
Normal
Normal
Normal
Abnormal
Replace IGBT in the block
Check waveform including.
of Gate Driver-96 ( Ref.Installation manual 4.23)
SW2-2:OFF on
Analog-LF30
Abnormal
Abnormal Check K2 on Replace K2 on
Error occurs ?
mA Detector-96 mA Detector-96
Yes Yes
Abnormal
No
Yes
Yes No
Replace Exchange
Replace HT Analog_LF30 SYSTEM-LF30 &
Cable Nexsc
Not changed
Replace X-
Ray Tube
Not changed
Replace HT
Transformer
* When the error : The Radio over current ( Radiographic tube current is
more than set value + 200mA ) “ F9 “ :
Normal
Check Abnormal
Replace mA
mA Detector- Detector-96
96
Normal
Normal