Está en la página 1de 3

Fault Database Flat TV

The Flat TV section is limited as flat panel sets are largely board changes these days, but it's here to post
anything I think may be of use

Due to the nature of flat panel repairs, the info here relates mainly to fault symptoms, PCBs and their part
numbers. Part numbers it must be said change with the wind, so beware!

Note: Manufacturers part numbers listed adopt the format used by the company I work for. Just ignore the first 4
characters!

GOODMANS

LD1546WD - No digital channels or menu - Carry out Kenmark Reset


LD2655HD - LVDS cable - VSTL30044366
LD3255HD - LVDS cable - HITAVS30044866
LD2661HDFVT - PSU - VSTL20326306
LD3761HDFVT - PSU - VSTL20326306

GXK

LD1542 - No sound - R001 (15R SMD) O/C on sub PCB (no supply to audio IC pin 4)

HITACHI

19LD3750DU (Vestel chassis) - Stuck in 'burn in' mode - Switch to analogue TV, navigate to the settings
menu (the icon with the spanner!), then press 4,7,2,5 on the remote control. This enters the service menu
where burn in mode can be turned off

KENMARK

Info relating to older sets

To access factory service modes 1 or 2, press DISPLAY, Red, Green, Yellow, DISPLAY on the remote control
unit
(Factory service modes 1 and 2 can be toggled between each other by pressing the menu button)

To access firmware & screen information, press DISPLAY, Red, Green, Yellow, Blue on the remote control
unit

Various models - No DVB - Enter 'firmware info' mode (as above) then switch off and on at the set

LVD163D - Stuck displaying service text and alternating coloured rasters - Hold down the standby button
then switch on at the mains to reset

Firmware update codes

These codes are for use with the appropriate Kenmark hardware interface
Goodmans LD1540WD - D644
Goodmans LD1945WD - D1BB, DB42, 5723, CF2F
Kenmark LVD163D - 455C, 06A7
Proline LVD1580WD - D05F, E57A, 465B
Proline LVD1985WD - 84E7, 01A5

Info relating to newer sets

19LVD01D - Loses channels after switching off and on again - Carry out Kenmark Reset

22LVD02D - In DVD mode, counts down from 10 minutes to zero then TV switches off - Requires firmware
update

LVD164D - Purple picture in DVD mode or rolling DVD picture or not reading DVDs - Carry out Kenmark
Reset

Kenmark Reset

* Select TV mode
* Press LCD Menu on remote
* Press 1147 (Factory menu)
* Go down to '001' (Init TV)
* Press right arrow on remote
* Wait for the installation menu to appear

LG

32LP1D - Green colouring on bright areas - Replace main (digital) PCB (LG**3313TD3035A)
26LX2R-ZE.ALUKLF - Brightness varying - Replace main (digital) PCB (LG**3313TL3024A)
RZ-26LZ50.AKPLWUA - Lines across screen - Replace main (digital) PCB (LG**3313TP2016A)

PANASONIC

TX26LXD500 - Limited colours on digital TV (analogue OK) - Replace DG PCB (PANATXNDGLPM)

PHILIPS

32FD9944/01S - Shuts down after switch on - Replace C2530, C2532, C2533, C2541, C2663, C2664 (100uF
25V use SEME100M35VR105) and C2662 (1000uF 25V) in PSU

SAMSUNG

LE32R41BDX/XEU - No, intermittent or pulsing backlight - ZDT803 faulty in PSU (low 24V to inverter)

LE20S51BX/XEU - Backlight shuts down after several hours - Replace VR301 on inverter PCB (due to hot
glue damage / conduction)

LE23R87BDX/XEU - Beeping sound from the function button PCB - Zener diode on the infra red receiver
PCB leaky (pulse noise can be scoped across it and on the KEY1 line)
LE40F71BX/XEU - No sound from speakers, headphones OK - Pin 3 of CN200 O/C to headphone PCB
(IDENT_HP)

LE40R73BDX/XEU - Intermittent not starting / Relay clicking / Power LED flashing - Replace swollen
capacitors CM806, CM811, CM812, CM817 in PSU

SONY

KDL26U2000 - Dead (5V from sub transformer OK to CN3006 of BDT board) - BDT board faulty
(SONY994802366)

TOSHIBA

17WLT56B - Dead - See note in mains adaptor section

17WLT56B - Coloured digital noise on screen (menu OK) - Replace main PCB (TOSHV20232633)

20WLT56B - Coloured digital noise on screen (menu OK) - Replace main PCB (TOSHV20218996)

27WLT56B - Dead - Power supply faulty (TOSHV20229345) (also check for dry joints)

42WLT66 - No digital TV reception - Replace IDTV PCB (TOSH75004015)

VESTEL CHASSIS

Service mode - Select analogue TV then on the RCU press MENU,4,7,2,5

VARIOUS

LCD sets that use the 12V 6.25A 4 PIN power supply (VSTL30029332 or JVC*VE30029332) - Not switching on
or shutting down after a while - Remove R72, clean the glue from its legs, then refit it

También podría gustarte