Documentos de Académico
Documentos de Profesional
Documentos de Cultura
kWh Meter
Operation and Instruction Manual
CT-2EA
88..8.8.8.8.
.. 8
CTR Avg Total Utility DG Idle ON Hrs R Y B
Bill MD Max
R kWAh
CAL
Contents
Installation ...........................................................4
Operations ..........................................................6
Programming ......................................................8
Communication .................................................13
1 CT-2EA NPAMCT2EA005
Note:
1. Please check the correct reference number as per the order.
Caution !
This equipment must be mounted only by professionals. The manufacturer shall not
be held responsible for failure to comply with the instructions in this manual.
+0.8mm
Digit Height 10mm x 5mm
92mm -0.0mm
Protection Index IP 54 (Front Panel)
+0.8mm
-0.0mm
Inputs Current:
86mm
l Via Current Transformer From 5A to 6000A configurable
92mm
with primary in multiples of 5 for -/5A or from 1A to 1200A
CT-2EA configurable in multiples of 1 for -/1A meter
l Insulated secondary 5A / 1A (Programmable)
96mm
CAL l Current circuit burden < 0.25VA
ac 3 Phase, 4 Wire kWh Meter
l Overload without CT Ratio 7A
2
! 1. Use 0.5 to 0.25 m cable for voltage terminal. Auxiliary Supply: 230V AC, ±30% , 50Hz
2
l Burden < 2.5VA
2. Use 2 to 6 mm cable for current terminal.
P A
N U
X RS 485
L1 S1
AUX. SUPPLY =
I1
230±30%, ac S2
L2
S1
L3 I2
N S2
S1
G I3
PULSE 1 PULSE S2
S
0/P = 1kWh
3. Select the device address of the CT-2EA for which the data is to be read
& the COM port to which it is connected.
4. Press 'Refresh'. All the data in the screen shall be updated. The following 3.2 Pulse Output :
data is available. The followings data is available on the screen.
a. Active Energy.
b. CT Ratio. (+) DC Supply (5V-24V)
c. Serial No. of CT2EA. External Resistance (For Supply use resistance of 6.8KΩ)
1. Pulse Output is Open Collector type. In the CRC 16, the first octet transmitted is LSB
2. External Resistance is to be used between DC Supply point 'S' & 'G' of pulse EXAMPLE : Development of CRC
output. CRC 16 FLAG
3. For 24V DC use an external resistance of 6.8KΩ. Initialize CRC register 1111 1111 1111 1111
4. The external resistance value will vary depending upon the external voltage of 1st character 0000 0010
(5-24V) being given by the user. 1111 1111 1111 1101
Movement 1 0111 1111 1111 1110 1
5. Minimum pulse width is 100msec.
Flag to 1, Polynome 1010 0000 0000 0001
6. 1 Pulse = 1kWh 1101 1111 1111 1111
Movement 2 0110 1111 1111 1111 1
Operations Flag to 1, Polynome 1010 0001
1100 1111 1111 1110
Movement 3 0110 0111 1111 1111 0
CT-2EA Flag to 0 Movement 4 0011 0011 1111 1111 1
R 101 1
2742.5
kW h 1001 0011 1111 1110
Movement 5 0100 1001 1111 1111 0
Movement 6 0010 0100 1111 1111 1
101 1
CAL 1000 0100 1111 1110
Movement 7 0100 0010 0111 1111 0
ac 3 Phase, 4 Wire kWh Meter 1. Scroll up key Movement 8 0010 0001 0011 1111 1
2. Scroll down key 101 1
3. Program/Enter key 1000 0001 0011 1110
4. Unit 2nd character 0000 0111
Scroll Scroll Prog 5. Values 1000 0001 0011 1001
Up Down
6. Reverse indication Movement 1 0100 0000 1001 1100 1
HPL ELECTRIC & POWER PVT. LTD. 101 1
Gurgaon, Haryana (INDIA) 1110 0000 1001 1101
Movement 2 0111 0000 0100 1110 1
Display Parameter 101 1
1101 0000 0100 1111
A. Auto Scroll Mode: Movement 3 0110 1000 0010 0111 1
Typical screen shot given below when meter is running. 101 1
1100 1000 0010 0110
CTR
Movement 4 0110 0100 0001 0011 0
5296. 7
kW h Cumulative Active Energy (kWh)
1.
5296. 7
Cumulative Active Energy
CRC 16 HEX A001® 2.
kWA h (kWh)
CRC 16
88 .. 8.8.8.8.
.. 8
CTR Avg Total Utility DG Idle On Hrs R Y B
Bill MD Max
R kWAh
no n>7 yes LCD Segment Check.
NEXT BYTE
PROGRAMMING PARAMETERS
END Key Operation : In CT-2EA meter following parameters can be set using push
buttons.
= OR exclusive
1. CT Ratio
n = number of information bit
a. CT Primary (5 - 6000)
b. CT Secondary (1 - 5)
2. Slave Address (Range: 1-255)
Operation and Instruction Manual 14 Operation and Instruction Manual 7
CT-2EA CT-2EA
Programming: Communication
To access/view the programming mode: The MODBUS used by the CT-2EA involves a dialogue using a Master - Slave
structure. The mode of communication is the RTU (Remote Terminal Unit) using
Keys Instruction Display Comment hexadecimal characters of at least 8 bit.
By entering the correct password, you will enter into the programming mode. The typical
screen shots of programming parameter are shown below: Following examples have been given using WINBUS32 S/w.
Example 1: If the Active energy in CT-2EA = 43.0kWh then user get the following
Keys Instruction Display Comment
response from CT-2EA.
CTR CT Primary and Secondary
Prog Press Once 0050-5 settings. Slave Function Number Data CRC CRC
address address of bytes high low
0x05 0x03 0x04 0x00 0x00 0x01 0xAE 0x3F 0xDF
Scroll Down Press Once sl 005 Slave address.
Example 2: If the CT Ratio in CT-2EA = 1200 (6000/5) then user get the following
Scroll down Press Once u 14.XX Version Number response from CT-2EA(Data in Hex Values):
Slave Function Number Data CRC CRC
Scroll down Press Once To exit from programming mode address address of bytes high low
0x05 0x03 0x02 0x04 0xB0 0x4A 0xF0
1. Set CT Ratio
Example 3: If Serial No. is 12110047, user get the following response:
The default CT Ratio is 50/5. To change the CT Ratio, press the "Prog" key once to
Slave Function Number Data CRC CRC
enter into the programming mode. The CT secondary can be programmed as 5 or 1 address address of bytes high low
and the CT primary can be programmed from 5 to 6000 in multiples of 5 if the CT
0x05 0x03 0x04 0x00 0xB8 0xC8 0xDF 0x8F 0x3A
secondary is 5A and 1 to 1200 in multiples of 1 if the CT secondary is 1A.
L3
S2 120W Prog Press Once 0----1 Set CT Primary.
S1
I2
N S2 CTR
S1
Scroll down Press Once 00---1 Moves cursor right.
1PULSE I3
G PULSE S2
0/P = CTR
S 1kWh Rx- Rx+ Scroll up Press Once 01---1 Digit increment by 1.
CTR
Scroll down Press Once 010--1 Moves cursor right.
CTR
Scroll down Press Once 0100-1 Moves cursor right.
Note: Serial Communication requires 120 W end-of-line resistance to be Prog Press Once To confirm setting.
connected on first and last device in RS485 MODBUS® network.
The End Of-Line resistance supplied with CT-2EA is to be connected between
Rx- and Rx+ as shown above.
2. Set Slave Address
RS485 configuration: The default slave address is 5. To change the slave address press the program key
Baud Rate : 9600 Bps once. The slave address can be set any value from 1 to 255.
Stop Bit : 1
Byte size : 8 Bit Keys Instruction Display Comment
Parity : None
sl 005 Previous slave address.
Slave Address setting The following are also supplied with this model:
Prog Press Once completed successfully.
2 numbers 120W End-Of-Line resistance.
(This includes one number extra supplied as spare.)
General Points:
3. Meter Software Version No.
For standard configuration, an Rs485 serial link 2 wire is used to connect up
Comment
to 255 meters with one Rs232 communication port on the master (computer/
Meter Software PLC etc.) over a distance of 1200 meters using MODBUS® protocol.
Prog Press Once u 14.XX Version Number
Comment Computor
RS485/232
Exit from Programming Converter
Prog Press Once Mode
RS485
The Meter will exit from the programming mode by coming to exit and pressing the
CTR Avg Total Utility DG Idle ON Hrs R Y B Bill MD Max Bill MD Max
Bill MD Max R kWAh R kWAh
R kWAh
CAL CAL
CAL
button and if user don't press any button for 1 minute, it will automatically exit from ac 3 Phase, 4 Wire kWh Meter ac 3 Phase, 4 Wire kWh Meter ac 3 Phase, 4 Wire kWh Meter
Cables & RS485/232 converter, computer are not supplied with this CT-2EA.