Está en la página 1de 5

www.ChineseStandard.

net --> Buy True-PDF


GB/T --> Auto-delivered in 0~10 minutes.
10095.2-2008

Translated English of Chinese Standard: GB/T10095.2-2008


www.ChineseStandard.net
Sales@ChineseStandard.net

GB
NATIONAL STANDARD OF THE

PEOPLE’S REPUBLIC OF CHINA


ICS 21.200
J 17

GB/T 10095.2-2008 / ISO 1328-2:1997

Replacing GB/T 10095.2-2001

Cylindrical gears - System of accuracy - Part 2:


Definitions and allowable values of deviations relevant
to radial composite deviations and runout information
(ISO 1328-2:1997, IDT)

圆柱齿轮 精度制

第 2 部分:径向综合偏差与径向跳动的定义和允许值
GB/T 10095.2-2008 How to BUY & immediately GET a full-copy of this standard?
1. www.ChineseStandard.net;
2. Search --> Add to Cart --> Checkout (3-steps);
3. No action is required - Full-copy of this standard will be automatically & immediately delivered to
your EMAIL address in 0~25 minutes.
4. Support: Sales@ChineseStandard.net. Wayne, Sales manager
Issued on: March 31, 2008 Implemented on: September 1, 2008
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration Committee.

www.ChineseStandard.net Page 1 of 23
www.ChineseStandard.net --> Buy True-PDF
GB/T --> Auto-delivered in 0~10 minutes.
10095.2-2008

Table of Contents

Foreword .......................................................................................................... 3 

ISO Foreword................................................................................................... 5 

ISO Introduction ............................................................................................... 6 

1 Scope ......................................................................................................... 7 

2 Normative references ................................................................................. 7 

3 Terms and defections ................................................................................. 8 

4 Symbols, quantities and units ..................................................................... 8 

5 Gear tooth accuracy terms relevant to radial composite deviations ........... 8 

6 Structure of the gear accuracy system ..................................................... 10 

7 Formulae for grade 5 accuracy tolerances for radial composite deviations

....................................................................................................................... 10 

Annex A ......................................................................................................... 12 

Annex B ......................................................................................................... 18 

Bibliography ................................................................................................... 23 

www.ChineseStandard.net Page 2 of 23
www.ChineseStandard.net --> Buy True-PDF
GB/T --> Auto-delivered in 0~10 minutes.
10095.2-2008

Foreword

GB/T 10095 Cylindrical gears - System of accuracy consists of the following 2


parts:

- Part 1: Definitions and allowable values of deviations relevant to


corresponding flanks of gear teeth;

- Part 2: Definitions and allowable values of deviations relevant to radial


composite deviations and runout information.

This Part is the second part of GB/T 10095.

This Part is identical with ISO 1328-2:1997 Cylindrical gears - ISO system of
accuracy - Part 2: Definitions and allowable values of deviations relevant to
radial composite deviations and runout information.

This Part is identical translation of ISO ISO 1328-2. For easy use, this Part
makes the following editorial changes:

- Modified some formats according to Chinese customs;

- Used decimal point “.” to replace “,” used as decimal point.

- For other normative references of ISO 1328-2:1997, the ones identically


used as Chinese standards were replaced by Chinese standards,
otherwise they were directly used as international standards.

This Part is the revision of GB/T 10095.2-2001 Cylindrical gears - System of


accuracy - Part 2: Definitions and allowable values of deviations relevant to
radial composite deviations and runout information. Compared with GB/T
10095.2-2001, the main changes are as follows:

- In order to be consistent with ISO 1328.2, the standard name was revised
to Cylindrical gears - System of accuracy - Part 2: Definitions and
allowable values of deviations relevant to radial composite deviations and
runout information;

- Modified some terms, e.g., “total tolerance” was modified to “total


deviation” (“radial consolidated total tolerance” was modified to “radial
consolidated total deviation”);

- Made changes to text description of some provisions.

Annex A, Annex B of this Part are informative.

This Part was proposed by China Machinery Industry Federation.

www.ChineseStandard.net Page 3 of 23
www.ChineseStandard.net --> Buy True-PDF
GB/T --> Auto-delivered in 0~10 minutes.
10095.2-2008

This Part shall be under the jurisdiction of National Technical Committee on


Gears of Standardization Administration of China.

The drafting organizations of this Part: Zhengzhou Machinery Research


Institute, Mechanical Science Research Institute.

Main drafters of this Part: Zhang Yuanguo, Ming Cuixin, Zhang Min’an, Li
Shizhong, Wang Changlu, Wang Qi, Yang Xingyuan, Chen Aimin, Lin Taijun,
Xu Hongji.

This Standard replaces the following previous standard:

- GB/T 10095.2-2001.

www.ChineseStandard.net Page 4 of 23
www.ChineseStandard.net --> Buy True-PDF
GB/T --> Auto-delivered in 0~10 minutes.
10095.2-2008

Cylindrical gears - System of accuracy - Part 2:


Definitions and allowable values of deviations relevant
to radial composite deviations and runout information

1 Scope

This Part of GB/T 10095 establishes a system of accuracy relevant to radial


composite deviations of individual cylindrical involute gears.

It specifies the appropriate definitions of gear tooth accuracy terms, the


structure of the gear accuracy system and the allowable values of the above
mentioned deviations.

The radial measurement accuracy system has different grade ranges than
elemental ranges in GB/T 10095.1. The diameter and module ranges for radial
composite deviations and runout are also different.

- The radial composite accuracy system comprises 9 accuracy grades for


F1’’ or f1’’ of which grade 4 is the highest and grade 12 is the lowest. The
module range extends from 0.2 mm to 10 mm and the diameter range
from 5.0 mm to 1000 mm, see clauses 6 and 7. Annex A (informative)
gives tables based on the formulae in clause 7;

- Runout is defined in Annex B and values are not given in the standard for
determining accuracy grade 5. Annex B provides information on runout for
use if agreed upon between purchaser and manufacturer.

2 Normative references

The following standards contain the provisions which, through reference in this
Part of GB/T 10095, constitute the provisions of this Part. For dated references,
subsequent amendments (excluding corrections) or revisions do not apply to
this Part. However, the parties who enter into agreement based on this Part are
encouraged to investigate whether the latest versions of these documents are
applicable. For undated reference documents, the latest versions apply to this
Part.

GB/T 10095.1-2008 Cylindrical gears - System of accuracy - Part 1:


Definitions and allowable values of deviations relevant to corresponding

www.ChineseStandard.net Page 7 of 23

También podría gustarte