Documentos de Académico
Documentos de Profesional
Documentos de Cultura
MARCH 7, 2002
Assembly Instructions Rev. 01 Model Series -ACH13-
Figure 2
Figure 1
Step 1: Insert (4) 94-FSVP03 vent plugs in the four Step 2: Install triangle shaped Caution sticker on
end holes from the bottom of this part (fig. 1). the bottom, with the point of the triangle centered
between the right side, end vent holes (fig. 2).
Figure 3
Figure 5 Figure 6
Step 6: Install 96-TRWS01 cut to length weather strip Step 7: Install (3) 95-PCST04 pc board spacers in the
on the top of each end cap, check for fit on both ends to top end of the blower housing (30-VL1034) (fig. 6).
insure a weather tight seal (fig. 5).
Figure 7
Figure 8
-2-
ACH13 Series Assembly Instructions
Figure 10
Figure 9
Step 10: Feed the wires from the blower (71-BLEH24) Step 11: Using the two wire managing clips
through the small hole on the side of the blower hous- (94-FSLG02) wrap the wire around them a few times
ing bracket (30-VL1034) (fig. 9). ending at the top clip. Note: leave enough wire to
connect to the pc board approximately 3 inches. (fig.
10).
(+) (-)
Figure 11 Figure 12
Step 12: Install the assembly to the end cap Step 13: Connect the wires to the pc board. The red
(30-VL956) using (4) 90-BTRP24 screws and (4) wire (+) to the first slot on the left and the black wire
92-WSFL02 flat washers (fig. 11). (-) to the second slot in the left. (fig. 12).
-3-
ACH13 Series Assembly Instructions
Figure 14
Figure 13
Step 14: Feed the wires the bottom and to wire management clips (fig. 13). Then connect them to the pc
board using the two slots on the far right side.(fig. 14).
2
3
1
Figure 15
Figure 16
-4-
ACH13 Series Assembly Instructions
Step 17: Install 96-TRWS01 cut to length weather Step 18: Fit the top extrusion to the lower extrusion
strip on the top of the bottom extrusion, check for fit between the end caps. Attach the top by driving the
on both sides to insure a weather tight seal (fig. 17). 93-DL01 each pin through the holes in the end cap
into the pin retaining grove. The pins should fit flush or
extend slightly out the end cap surface (fig. 18a-b).
Figure 20a
Figure 20b
Figure 19
Step 20: Install the (2) top closing screws w/ retain-
Step 19: * Critical * Install all labels listed in the ers (fig. 11a). Step 13: Close the lid and tighten
work order & BOM on the inner surface centered and fasteners.(Note: Retainer is installed on inside of
parallel with the front & rear edges of top extrusion the top. ** Caution ** When installing the screws it
(fig. 19). is necessary to press down firmly in the center of
the top in order to properly start these screws.* DO
NOT OVER TIGHTEN * (fig. 20b)
-5-
ACH13 Series Assembly Instructions
Figure 21 Figure 22
Step 21: Attach the 30-VL1109 bracket to bottom Step 22: Attach the 30-VL1110 bracket to
of the lower housing assembly with 90-BTHH32 bolts 30-VL1108 bracket with the specified fasteners listed
and specified split washers. Caution: Do not to over on the work order & BOM. * Caution: Do not over
tighten (fig. 21). tighten. * Caution: Do not to over tighten. (fig. 22)
-6-
ACH13 Series Assembly Instructions
Figure 24 Figure 25
Step 24: Insert the completed assembly into the Step 25: Place the bagged assembly in the card-
protective plastic bag. (fig. 24) board insert. Use one piece of tape in the middle of
the insert to hold it together.(fig.25)
Step 26: Insert the completed assembly into the assembled box. (fig.26)
Step 27: Insert the Installation Packet into the box and wall mount instruction sheet, if in the BOM . ***Critical
: Check work order & BOM to verify contents of the Installation Packet and any additional instruction sheets.***
(fig.27)
Step 28: Staple box closed, 2 places equally spaced. (fig.28)
-7-